Shop-Vac SS16 Series User manual

Brand: Shop-Vac

Model: SS16 Series

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

User manual

Please review before operating vac.

Manual del usuario

Por favor lea esta manual antes de usar la aspiradora.

Series

SS11, SS14, SS16

Wet/Dry Vacuum

Household and Workshop Use

Series

SS11, SS14, SS16

Aspiradora para aspiración de residuos

Líquidos/Sólidos

Para Uso Doméstico y Comercial

ATTENTION!

Read all safety rules carefully

before attempting to operate.

Retain for future reference.

ATENCIÓN!

Lea cuidadosamente todas

las normas de seguridad

antes de utilizar la aspira-

dora. Conserve esta man-

ual para consultas futuras.

PELIGRO!

Nunca opere esta unidad ante

la presencia de materiales o

vapores inflamables dado que

los artefactos eléctricos pro-

ducen arcos o chispas que

pueden causar un incendio o

una explosión.

NO DEJE LA ASPI-

RADORA FUNCIO-

NANDO SIN VIGI-

LANCIA!

DANGER!

Never operate this unit when

flammable materials or vapors

are present because electri-

cal devices produce arcs or

sparks that can cause a fire

or explosion.

NEVER OPERATE

UNATTENDED!

SHOP-VAC CORPORATION

2323 Reach Road, P.O. Box 3307

Williamsport, PA 17701-0307

(570) 326-3557

www.shopvac.com

SHOP-VAC CANADA

1770 Appleby Line

Burlington, Ontario L7L 5P8

(905) 335-9730

www.shopvac.ca

Shop Vac-México, S.A. de C.V.

Av. Mariano Otero #5095, Local 1 PB

Col. La Calma

Zapopan, Jalisco C.P. 45070

MÉXICO

52 (33) 3188 6388

Patents Issued and Pending.

Brevets délivrés et en instance.

Patentes registradas y en trámite.

Manuel d’utilisation

Veuillez lire avant d’utiliser l’aspirateur.

Séries

SS11, SS14, SS16

Aspirateur pour déchets secs et humides

Pour utilisation domestique ou dans les entrepôts

ATTENTION!

Lisez attentivement les in-

structions sur la sécurité

avant d’utiliser cet appareil.

Conservez ce manuel pour

vous y reporter ultérieurement.

DANGER

N’utilisez jamais cet aspira-

teur en présence de vapeurs

ou de matières inflammables.

Les appareils électriques

produisent des arcs ou des

étincelles qui peuvent causer

un incendie ou une explosion.

NE JAMAIS FAIRE

FONCTIONNER SANS

SURVEILLANCE!

BRAND/MARQUE/MARCA

in sketches B and C may be used

to connect this plug to a 2-pole

receptacle as shown in sketch B

if a properly grounded outlet is not

available. The temporary adaptor

should be used only until a properly

grounded outlet (sketch A) can be

installed by a qualified electrician.

The green colored rigid ear, lug or

the like extending from the adaptor

must be connected to a permanent

ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be

held in place by a metal screw.

IN CANADA, THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN

ELECTRICAL CODE. Make sure that the appliance is connected to an outlet having the same

configuration as the plug. No adapter should be used with this appliance.

This appliance must be grounded. If it should malfunction or breakdown, grounding provides

a path of least resistance for electric current to reduce the risk of electric shock. This appli-

ance is equipped with a cord having an equipment-grounding conductor and grounding plug.

The plug must be inserted into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

WARNING – IMPROPER CONNECTION OF THE EQUIP-

MENT-GROUNDING CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE PERSON

IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY

GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE

– IF IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED

BY A QUALIFIED ELECTRICIAN.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks

like the plug illustrated in sketch A. A temporary adaptor that looks like the adaptor illustrated

GROUNDING INSTRUCTIONS

UNPACKING AND SET-UP

1. Pull lid latches in an outward motion, remove tank cover and any accessories that may have

been shipped in the tank.

2. Attach caster system following the instructions and illustrations in this manual.

3. Attach side tank handles following the instructions and illustrations in this manual.

4. Before replacing tank cover, please refer to Dry Pick Up or Wet Pick Up Operation in this

manual to ensure you have the proper filters installed for your cleaning operation.

5. Replace tank cover, and apply pressure with thumb to each latch until it snaps tightly in

place. Make sure all lid latches are clamped securely.

When using the appliance at a distance where an extension cord becomes necessary, a 3-conductor

grounding cord of adequate size must be used for safety, and to prevent loss of power and overheating.

Use the table below to determine A.W.G. wire size required. To determine ampere rating of your vacuum,

refer to nameplate located on rear of motor cover. Before using appliance, inspect power cord for loose

or exposed wires and damaged insulation. Make any needed repairs or replacements before using

your appliance. Use only three-wire outdoor extension cords which have three-prong grounding-type

plugs and three-pole receptacles which accept the extension cord’s plug. When vacuuming liquids, be

sure the extension cord connection does not come in contact with the liquid.

NOTE: STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS

LOW. THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE APPLIANCE. TO REDUCE THE

FREQUENCY OF STATIC SHOCKS IN YOUR HOME, THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR

WITH A CONSOLE OR INSTALLED HUMIDIFIER.

EXTENSION CORDS

When using an electrical appliance, basic precautions should always be followed, including the

following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY:

1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before

servicing. Connect to a properly grounded outlet only. See Grounding Instructions.

2. Do not expose to rain – store indoors.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near chil-

dren.

4. Use only as described in this manual. Use only Manufacturer’s recommended attachments.

5. Do not use with damaged cord or plug. If appliance is not working as it should, has been

dropped, damaged, left outdoors or dropped into water, contact Shop-Vac Corporation for

assistance.

6. Do Not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around

sharp edges or corners. Do not run appliance over cord. Keep cord away from heated sur-

faces.

7. Do not unplug by pulling on cord. To unplug, grasp the plug; not the cord.

8. Do not handle plug or appliance with wet hands.

9. Do not put any object into openings. Do not use with any openings blocked; keep free of dust,

lint, hair and anything that may reduce air flow.

10. Keep hair, loose clothing, fingers and all parts of body away from openings and moving

parts.

11. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot

ashes.

12. Do not use without dust bag and/or filters in place.

13. Turn off all controls before unplugging.

14. Use extra care when cleaning on stairs.

15. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where

they may be present.

16. Do not use your cleaner as a sprayer of flammable liquids such as oil base paints, lacquers,

household cleaners, etc.

17. Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as

asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering materials.

Specially designed units are available for these purposes.

18. Do not pick up soot, cement, plaster or drywall dust without cartridge filter and collection

filter bag in place. These are very fine particles that may pass through the foam and affect the

performance of the motor or be exhausted back into the air. Additional collection filter bags are

available.

19. Do not leave the cord lying on the floor once you have finished the cleaning job. It can become

a tripping hazard.

20. Use special care when emptying heavily loaded tanks.

21. To avoid spontaneous combustion, empty tank after each use.

22. The operation of a utility vac can result in foreign objects being blown into eyes, which can

result in eye damage. Always wear safety goggles when operating vacuum.

23. STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum cleaner

when you are tired, distracted or under the influence of drugs, alcohol or medication causing

diminished control.

24. WARNING! Do NOT use this vacuum cleaner to vacuum lead paint debris because this may

disperse fine lead particles into the air. This vacuum cleaner is not intended for use under EPA

Regulation 40 CFR Part 745 for lead paint material cleanup.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING

– DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND/OR OPERATING. UNPLUG UNIT WHEN NOT IN USE.

Volts

Total length of cord in feet

120V

Ampere Rating

More Not More

Than Than

0 - 6

6 - 10

10 - 12

12 - 16

25 50 100

150

AWG

Not recommended

6. Insert machine hose end into inlet of tank. Twist

slightly to tighten the connection (Figure 1).

7. Attach the extension wands to the accessory end

of the hose. Twist slightly to tighten the connection

(Figure 1).

8. Attach one of the cleaning accessories (depending on your cleaning requirements) to the

extension wands. Twist slightly to tighten the connection (Figure 1).

9. Plug the cord into the wall outlet. Your cleaner is ready for use.

I = ON, O =OFF

NOTE: MANY MORE USEFUL TOOLS ARE AVAILABLE AT YOUR LOCAL DEALER OR SHOP-VAC

WEBSITE.

With Wheel Dolly

You will find two casters (b), two large rear wheels (c), one axle (d), tool rack (e) and two cap

nuts (f). If your vacuum is 16 U.S. gallons (60.5 liters) or larger you will also find two screws,

two metal flat washers and two square nuts with your wet/dry vacuum. Assemble as follows:

1. Make sure the cord is disconnected from the receptacle then remove the tank cover.

2. If your unit is 4 U.S. gallon (15.1 liter) to 14 U.S. gallon (53 liter), assemble as follows:

a. Turn tank upside down so the bottom is facing up.

b. Continue on to step 4 below.

3. If your unit is 16 U.S. gallon (60.5 liter) or above, assemble as follows:

a. With the tank upright and back facing you, insert square nut into one of the two slots

located in back of dolly (Figure 11).

b. Place metal flat washer over stem of screw.

c. Tilt the tank forward slightly and locate the hole provided in the underside of the

dolly directly below the slot containing the square nut (Figure 12).

d. Place the screw, containing the flat washer, into the hole and turn clockwise until

end of screw is connected to square nut. If you have difficulty getting the screw to

WARNING – ALWAYS DISCONNECT THE PLUG FROM THE

WALL OUTLET BEFORE REMOVING THE TANK COVER.

When using the reusable dry filter to pick up dust and dry

material, you must install foam sleeve and reusable dry filter

to ensure proper filtration. If the vacuum has been used

to pick up liquids, the foam sleeve must be cleaned and

(Not standard with all models)

INSTALLING FOAM SLEEVE AND REUSABLE

DRY FILTER

Not all units are equipped with the same caster system. Follow the instructions, which

apply to your specific unit.

With Caster Feet

1. With cord disconnected from receptacle and tank

cover removed, turn tank upside down so that the

bottom is facing up.

2. With a pair of scissors, trim the enclosed template

to ﬁt your size tank. Sizes will be 11”, 14” or 16”

diameters.

3. Once template is cut out, place on bottom of tank.

Align inlet arrow on template with center of inlet on

tank (Figure 2).

4. If caster feet are attached together, separate by

removing webbing.

5. Take caster foot marked with the letter A and align

arrow on foot (Figure 3) with arrow on template

also marked with the letter A (Figure 4).

6. Place groove of foot over rim of tank and push until

the caster foot is tight against bottom of tank (Figure 5).

7. Secure feet with screw and washer when provided (Figure 6).

8. Repeat steps 4-7 with remaining feet.

9. If plastic ﬂat washers are included in hardware package, place one ﬂat washer over stem

of each caster. NOTE: Flat washers are not required with all units.

10. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and

twisting motion until casters snap into place (Figure 7).

11. Return tank to upright position.

CASTER SYSTEM ASSEMBLY

TOOL HOLDER

(Not standard with all models)

1. With rear of unit facing you, take tool holder and position it with tabs facing rear of unit

(Figure 18).

2. Place "J" shaped tabs into the slots on cord wraps (Figure 19).

3. Press down until tabs snap into place.

4. Press down on center of tool holder until tab latches on bottom of lid (Figure 20).

Arrow

Template

Bottom of Tank

DRY PICK UP

Tank Bottom

INSTALLING THE CARRIAGE HANDLE

(Not standard with all models)

Attach carriage handle to tank by inserting bolt through the center hole of handle and tank,

secure with nut provided. Attach side handles with screws provided. Be sure to spread ends of

carriage handle when assembling to prevent damage to tank.

Item Description

1 Metal tank handle

2 Side tank handle

3 #10 x 3/4” Screw hex head

4 Bolt 1/4 - 20 x 1/2”

5 1/4 - 20 Hex nut

SIDE TANK HANDLE ASSEMBLY

(Not standard with all models)

Attach side handles to tank with screws provided (Figure 21).

With Caster Dolly

You will ﬁnd four casters (a) with your wet/dry vacuum. If your vacuum is 16 U.S. gallon (60.5

liter) or larger, you will also ﬁnd two screws, two metal ﬂat washers and two square nuts. As-

semble as follows:

1. Make sure the cord is disconnected from the receptacle then remove the tank cover.

2. If your unit is 4 U.S. gallon (15.1 liter) to 14 U.S. gallon (53 liter), assemble as follows:

a. Turn tank upside down so the bottom is facing up.

b. Insert casters into bottom of dolly by placing stem of caster into holes provided. Apply

pressure and twisting motion until casters snap into place (Figure 8).

c. Return tank to upright position.

3. If your unit is 16 U.S. gallon (60.5 liter) or above, assemble as follows:

a. With the tank upright and back facing you, insert square nut into one of the two slots

located in back of dolly (Figure 9).

b. Place metal ﬂat washer over stem of screw.

c. Tilt the tank forward slightly and locate the hole provided in the underside of the dolly

directly below the slot containing the square nut (Figure 10).

d. Place the screw, containing the ﬂat washer, into the hole and turn clockwise until end of

screw is connected to square nut. If you have difﬁculty getting the screw to connect to

the square nut, push downward on the square nut with the eraser end of a pencil while

turning the screw.

e. Finish tightening the screw using 7/16” socket, wrench or nut driver.

f. Repeat steps a to e with the second slot in dolly.

connect to the square nut, push downward on the square nut with the eraser end of a

pencil while turning the screw.

e. Finish tightening the screw using 7/16” socket, wrench or nut driver.

f. Repeat steps a to e with the second slot in dolly.

g. Turn tank upside down so bottom is facing up. Continue on to set 4 below.

4. Place axle upright on a hard surface and hammer on one cap nut (Figure 13). Place one

wheel on axle and slide down to cap nut (Figure 14). Be sure flat side of wheel hub is

facing outward.

5. Slide axle through holes provided in tool rack (Figure 15).

6. Slide remaining wheel onto axle and hammer on second cap nut (Figure 16).

7. Install tool rack assembly onto dolly (already installed on tank) by placing large slot in

tool rack over rim on back of dolly (Figure 17). Push tool rack onto dolly until the bottom

of tool rack is flush with bottom of dolly. NOTE: It is normal for tool rack to fit tightly onto

dolly.

8. Secure with four screws provided (Figure 18).

9. If plastic flat washers are included in hardware package, place one flat washer over stem

of each caster. NOTE: Flat washers are not required with all units.

10. Insert casters into front of dolly by placing stem of casters into holes provided. Apply pres-

sure and twisting motion until casters snap into place (Figure 19).

11. Return tank to upright position.

22 23

INSTALLING THE DISPOSABLE FILTER BAG

(Not standard with all models)

1. Use for dry pick up only. Use in conjunction with cartridge

filter for picking up soot, cement, plaster or drywall dust.

2. With cord disconnected from receptacle, pull latches in an

outward motion and remove tank cover.

3. Grasp cardboard collar firmly and slide rubber guard onto

inlet fitting as far as possible (Figure 34).

4. When secured in place, expand bag and position around the inside of the tank (Figure 35).

WET PICK UP OPERATION

Remove ALL dirt and debris found in the tank. The vacuum requires only a minimum of conver-

sion when going from dry to wet pick up. Remove all dry use filters from the vacuum. A clean

cartridge filter may be used for vacuuming small amounts of liquids. For proper installation of

the cartridge filter refer to Installing the Cartridge Filter. For best results when vacuuming large

quantities of liquid, remove the cartridge filter. When vacuuming liquids containing debris, it is

recommended purchasing a foam sleeve and install over filter cage; otherwise a foam sleeve

is not required for wet pick up. Foam sleeve and additional filters may be purchased by visiting

our website at www. shopvac.com, contacting our customer service department, or purchasing

at your local Shop-Vac

distributor.

Misting in exhaust air may occur if the filter becomes saturated during wet pick up. If misting

occurs, remove filter and allow to dry or, replace with another dry filter to eliminate the misting

and possible dripping of liquid around the lid. Turn the unit off immediately upon completing a

wet pick-up job or when tank is full and ready to be emptied. Raise the hose to drain any excess

liquid into the tank. The interior of the tank should be periodically cleaned.

The foam sleeve should be cleaned periodically as described in the following steps:

1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place

tank cover in an upside down position. Remove foam sleeve by sliding it up and off the lid

cage.

2. Shake excess dust off foam sleeve with a rapid up and down movement.

3. Hold foam sleeve under running water for a minute or two, rinsing from the inside. A water

wash is not always required, depending on the condition of the foam sleeve.

4. Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The

foam sleeve is now ready to be reinstalled on the lid cage.

EMPTYING LIQUID WASTES FROM THE TANK

Not all units are equipped with tank drains. Follow the instructions, which apply to

your specific unit.

Without Tank Drain

Liquid waste may be emptied by removing the tank cover. To empty, stop the motor and

remove the plug from the wall receptacle. Remove the tank cover and deposit the liquid waste

contents in a suitable drain. After tank is empty, return the cover to its original position. To

continue use, plug the cord into the wall receptacle and turn the unit on.

With Tank Drain

Liquid waste may be emptied by removing the tank drain. To empty, turn unit off and remove

plug from wall receptacle. Remove the drain cap and deposit the liquid waste contents in a

suitable drain. After the tank is empty, return the drain cap to its original position. To continue

use, plug the cord into the wall receptacle and turn the unit on.

The vacuum is equipped with an automatic suction shut-off that operates when picking up

liquids. As the level of the liquid rises in the tank, an internal float rises until it seats itself

against a seal at the intake of the motor, shutting off suction. When this happens, the motor will

develop a higher than normal pitch noise and the suction is drastically reduced. If this occurs,

turn unit off immediately. Failure to turn unit off after float rises and shuts off suction will result

in extensive damage to the motor. To continue use, empty the liquid waste from the tank as

outlined in the previous paragraph.

NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD LOSE SUCTION. IF THIS OCCURS,

PLACE VAC IN UPRIGHT POSITION AND TURN SWITCH OFF. THIS WILL ALLOW THE FLOAT TO

RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE TO CONTINUE OPERATION.

AUTOMATIC SUCTION SHUT-OFF

LUBRICATION

No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.

Trouble Possible Cause Remedy

Suction weakens or

cleaner runs hot

Clogged filter Brush dirt from filter. If condition continues,

change filter.

Air leak Check all fittings for tight fit (nozzles, hose, etc.)

Check that tank cover is sealed properly.

Obstruction in hose

or nozzle

Check nozzle, hose, etc. for obstructions, and

remove if present.

Misting in the

exhaust air

Saturated filter Replace saturated filter with a dry filter.

TROUBLESHOOTING

WARNING –

IF ANY OF THE MOTOR HOUSING PARTS

SHOULD BECOME DETACHED OR BROKEN, EXPOSING THE MOTOR OR ANY

OTHER ELECTRICAL COMPONENTS, OPERATION SHOULD BE DISCONTINUED

IMMEDIATELY TO AVOID PERSONAL INJURY OR FURTHER DAMAGE TO THE

VACUUM. REPAIRS SHOULD BE MADE BEFORE REUSING THE VACUUM.

Your vacuum can be used as a powerful blower. To use your unit as a blower,

clear hose of any obstruction. Insert machine hose end into blower port on

rear of unit (Figure 36). Twist slightly to tighten the connection. Caution

should be used when using as a blower due to the powerful force of air when

using certain attachments.

WARNING – ALWAYS WEAR EYE PROTECTION TO PRE-

VENT ROCKS OR DEBRIS FROM BEING BLOWN OR RICOCHETING INTO

THE EYES OR FACE, WHICH CAN RESULT IN SERIOUS INJURY.

BLOWER FEATURE

STORAGE

Before storing your vacuum cleaner the tank should be emptied and cleaned.

The power cord can be wrapped around the cord wraps provided on the tank

cover on rear of unit (Figure 37). Accessories may be stored in the tool holder

(not standard on all models) so they can be readily available. The vacuum

should be stored indoors.

FIVE YEAR HOME USE WARRANTY

Your Shop-Vac® vacuum cleaner is warranted for normal household use, in accordance with

the User Manual, against original defects in material and workmanship for a period of five years

from date of purchase. Should this product be used for commercial or rental use, a 90 day lim-

ited warranty will apply. Shop-Vac Corporation warrants placing this vacuum cleaner in correct

operating condition, by repair or parts replacement, during the warranty period, without charge.

This warranty does not cover accessories. Use of non-recommended filters and/or accessories

may void the manufacturer's warranty. Shop-Vac® assumes no responsibility for damage or

faulty performance caused by misuse, careless handling, and where repairs or modifications

WARNING FOR FINE DUST & POWDERS

When vacuuming fine dust, or powders of any kind (ex. plaster, drywall dust, cold ashes, con-

crete dust, etc.)...a high efficiency drywall filter bag must be used. When vacuuming normal

household dust and debris, standard household disposable filter bags may be used. These

"large bag" filters connect to the air inlet fitting on the inside of the vacuum tank.

FILTER SELECTION GUIDE

SIZE

5-8 U.S. Gal (18.9-30.3L)

10-14 U.S. Gal (37.8-53L)

15-22 U.S. Gal (56.8-83.2L)

90671/

90672/

90673/

90107/ REUSABLE DRY FILTER AND MOUNTING RING

fits most Shop-Vac

Wet/Dry Vacuums.

90585/ FOAM FILTER SLEEVE fits most Shop-Vac

Wet/Dry Vacuum

Fine dust

Drywall

Standard

Household

90661/

90662/

90663/

dried before installing for dry pick up. With tank cover in

an upside down position, slide foam sleeve down over lid

cage pulling until foam sleeve completely covers lid cage

(Figures 22, 23). Center the reusable dry filter on lid cage

(Figure 24), slide mounting ring down over filter until ring is

positioned against the ribs of the lid cage (Figure 25). The

reusable dry filter should always be in position over the foam sleeve for dry

pick up. To remove the filter for cleaning, remove mounting ring and filter from

lid cage (Figure 26). To clean the reusable dry filter, shake off excess dirt and

dust or (depending on the condition of the filter) rinse with water. Allow the filter

to dry completely and reinstall. DO NOT MACHINE WASH OR DRY.

(Not standard with all models)

NOTE: If foam sleeve is in postion over lid cage, it must be removed before installing cartridge

filter.

The cartridge filter can be used for wet or dry pick

up; installation is the same for both. When picking up

large quantities of liquid please refer to the Wet Pick Up

Operation section in this manual. Use the cartridge filter

in position over the lid cage for most general dry material

pick up. With the tank cover in an upside down position,

slide the cartridge filter down over the lid cage, pushing

until the filter seals against the cover (Figure 27). Place

filter retainer into the top of the cartridge filter, hold the

tank cover with one hand, turn the handle on the filter

retainer clockwise to tighten, locking the filter into place

(Figures 28 & 29). To remove the filter for cleaning, again

hold the tank cover and turn the filter retainer counter-

clockwise to loosen and remove, slide the cartridge filter

off the lid cage (Figures 30 & 31). To clean the cartridge

filter shake or brush off excess dirt or rinse (from the inside of the filter) with water, dry com-

pletely (approximately 24 hours) and reinstall (Figures 32 & 33). NOTE: If the filter has been

used for wet pick up, it must be cleaned and dried before using for dry pick up.

INSTALLING THE CARTRIDGE FILTER

27 28

NOTE: WET PICK UP ACCESSORIES SHOULD BE WASHED PERIODICALLY, ESPECIALLY AFTER

PICKING UP WET, STICKY KITCHEN ACCIDENTS. THIS CAN BE ACCOMPLISHED WITH A WARM

SOLUTION OF SOAP AND WATER.

Page is loading ...

Shop-Vac SS16 Series User manual

Brand: Shop-Vac

Model: SS16 Series

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Shop-Vac SS16 Series Manuel utilisateur
español: Shop-Vac SS16 Series Manual de usuario

Shop-Vac SS16 Series User manual

This manual is also suitable for

Shop-Vac SS16 Series User manual

in other languages

Related papers

Other documents