Genesis GL20DIDKA2 User manual

20V Lithium-Ion Impact Driver

Tournevis à percussion à pile lithium-ion 12V

Destornillador de impacto de litio-ion de 12V

GLID20A

Operator’s Manual

Manuel d’utilisation

Manual del Operario

888-552-8665

TOLL FREE

HELP LINE:

WEBSITE:

www.genesispowertools.com

English

20V Lithium-Ion Impact Driver

Operator’s Manual GLID20A

SPECIFICATIONS

• Model: ------------------------ GLID20A

• Rated Power: ----------------- 20V DC

• No-Load Speed: -------------- 0-2200 RPM, Reversible

• Impacts Per Minute: ---------- 0-3800

• Maximum Torque: ------------ 1062 In-lbs

• Chuck Size: ------------------- 1/4" Hex

• Battery: ----------------------- 20V, Lithium-ion, 1.5Ah

• Charger Input: ---------------- 120V~, 60 Hz

• Charging Time: --------------- 3-5 Hours

• Net Weight: ------------------- 2.5 Lbs

Includes: Battery Pack, Charger, and #2 Phillips bit

WARNING: To reduce the risk of injury, user must read and understand this

operator’s manual before operating this tool. Save this Manual for future reference.

Toll-Free Help Line: 1-888-552-8665

WARNING: The Operation of any power tool can result in foreign

objects being thrown into your eyes, which can result in severe eye damage.

Before beginning tool operation, always wear safety goggles or safety glasses

with side shields and a full face shield when needed. We recommend Wide

Vision Safety Mask for use over eyeglasses or standard safety glasses with side

shields. Always wear eye protection which is marked to comply with ANSI Z87.1.

Look for this symbol to point out important safety

precautions. It means attention!!! Your safety is

involved.

GENERAL SAFETY RULES

WARNING: Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals known to cause

cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to ﬁlter out microscopic particles.

WARNING: Read and understand all warnings, cautions and operating

instructions before using this equipment. Failure to follow all instructions listed below

may result in electric shock, ﬁre and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WEAR YOUR

FORESIGHT IS BETTER

THAN NO SIGHT

SAFETY GLASSES

3

English

WORK AREA SAFETY

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•

Do not operate power tools in explosive atmospheres, such as in the presence of

ﬂammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

•

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adaptor plugs in any earthed (grounded) power tools. Double insulated tools are equipped with a polarized

plug (one blade is wider than the other). This plug will ﬁt in a polarized outlet only one way. If the plug does not

ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install a polarized

outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded

power cord and grounded power supply system.

•

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

•

Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is

grounded.

•

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged cords increase the risk of electric shock.

•

When operating a power tool outside, use an extension cord suitable for

outdoor use

. These cords are rated for outdoor use and reduce the risk of electric shock.

•

Do not use AC only rated tools with a DC power supply. While the tool may appear to

work. The electrical components of the AC rated tool are likely to fail and rate a hazard to the operator.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use

tool while tired or under the inﬂuence of drugs, alcohol, or medication. A moment of inattention while operating

power tools may result in serious personal injury.

•

Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection for appropriate conditions will reduce personal injuries.

•

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents may cover moving

parts and should be avoided.

•

Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power

tool with your ﬁnger on the switch or plugging in power tools that have the switch on invites accidents.

•

Remove any adjusting keys or wrenches before turning the power tool on. A

wrench or key that is left attached to a rotating part of the tool may result in personal injury.

•

Do not overreach. Maintain proper footing and balance at all times. Loss of balance can cause an injury

in an unexpected situation.

•

If devices are provided for connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of these devices can

reduce dust related hazards.

•

Do not use a ladder or unstable support. Stable footing on a solid surface enables better

control of the tool in unexpected situations.

•

Keep tool handles dry, clean and free from oil and grease. Slippery handles cannot

safely control the tool.

TOOL USE AND CARE

• Secure the workpiece. Use clamp or other practical way to hold the workpiece to a stable platform.

Holding the workpiece by hand or against your body is unstable and may lead to loss of control.

English

20V Lithium-Ion Impact Driver

Operator’s Manual GLID20A

• Do not force the power tool. The tool will perform the job better and safer at the feed rate for

which it is designed. Forcing the tool could possibly damage the tool and may result in personal injury.

•

Use the correct power tool for the job. Don’t force the tool or attachment to do a job for which

it is not designed.

•

Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired or replaced by an authorized service center.

•

Turn power tool off, and disconnect the plug from the power source and/or battery pack

from the power tool before making any adjustments, changing the accessories, or storing the tools. Such

preventive safety measures reduce the risk of an accidental start up which may cause personal injury.

•

Store idle tool out of reach of children and other inexperienced persons. It is

dangerous in the hand of untrained users.

•

Maintain power tools with care. Check for proper alignment and binding of moving parts,

component breaks, and any other conditions that may affect the tool’s operation. A guard or any other part that

is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal

injury.

•

Use recommended accessories. Using accessories and attachments not recommended by the

manufacturer or intended for use on this type tool may cause damage to the tool or result in personal injury to

the user. Consult the operator’s manual for recommended accessories.

•

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

•

Feed the workpiece in the correct direction and speed. Feed the workpiece into a

blade, cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only. Incorrectly

feeding the workpiece in the same direction may cause the workpiece to be thrown out at high speed.

•

Never leave the tool running unattended, turn the power off. Do not leave the tool

until it comes to a complete stop.

BATTERY TOOL USE AND CARE

• Ensure the trigger switch is in the off position before inserting battery pack.

Inserting the battery pack into power tools that have the switch on invites accidents.

•

Recharge only with the charger speciﬁed by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of ﬁre when used with another battery pack.

•

Use battery tools only with speciﬁed battery pack. Use of any other battery packs may

create a risk of injury and ﬁre.

•

Avoid storing battery pack in a container with other metal objects such as

nails, coins, clips, keys, screws, or other small metal objects that can make

a connection from one terminal to another. Always protect the battery terminals when

battery pack is not being used. Connecting the battery terminals together may cause burns or a ﬁre.

•

Under abusive conditions, liquid may be ejected from the battery. Avoid contact.

If contact accidentally occurs, ﬂush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

•

Battery tools do not need to be plugged into an electrical outlet, therefore, they are

always in operation condition. Be aware of possible hazards when not using your battery tool or when changing

accessories. Following this rule will reduce the risk of electric shock, ﬁre or personal injury.

WARNING: USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR

OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST

AND ASBESTOS. Direct particles away from face and body. Always operate tool in a

well-ventilated area and provide for proper dust removal. Use dust collection system

wherever possible. Exposure to the dust may cause serious and permanent respiratory

or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid

breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into

your mouth or eyes, or lay on your skin may promote absorption of harmful material.

Always use properly ﬁtting NIOSH/OSHA approved respiratory protection appropriate for

dust exposure, and wash exposed areas with soap and water.

5

English

SERVICE

• Have your power tool serviced by a qualiﬁed repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

•

Service your power tool periodically. When cleaning a tool, be careful not to disassemble any

portion of the tool since internal wires may be misplaced or pinched.

SAVE THESE INSTRUCTIONS

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double insulated tools can

use either a two or three wire extension cord. As the distance from the power supply outlet increases, you must

use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop

in voltage, resulting in loss of power and possible tool damage. Refer to the table shown below to determine the

required minimum wire size.

The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a 14-gauge cord

can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total

length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord

for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire

size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be sure it is marked with the sufﬁx “W-A” (“W” in Canada) to

indicate that it is acceptable for outdoor use.

• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged

extension cord or have it repaired by a qualiﬁed person before using it.

• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

SPECIFIC SAFETY RULES FOR CORDLESS IMPACT

DRIVERS

WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT (GAINED

FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT SAFETY RULES. If

you use this tool unsafe or incorrectly, you can suffer serious personal injury!

•

Hold the tool by insulated gripping surfaces when performing an operation

where the tool may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool

“live” and shock the operator.

•

Do not leave the tool running. Operate the tool only when hand-held.

•

Be aware that this tool is always in an operating condition, because it does not have

to be plugged into an electric outlet.

•

When operating the tool from an elevated position, be aware of people or things

beneath you.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate

Amperes

(At Full Load)

Extension Cord Length

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 200 Feet

0–2.0 18 18 18 18 16 16

2.1–3.4 18 18 18 16 14 14

3.5–5.0 18 18 16 14 12 12

5.1–7.0 18 16 14 12 12 10

7.1–12.0 18 14 12 10 8 8

12.1–16.0 14 12 10 10 8 6

16.1–20.0 12 10 8 8 6 6

English

20V Lithium-Ion Impact Driver

Operator’s Manual GLID20A

• Always hold the tool ﬁrmly in your hands before switching the tool “ON”. The reaction to

the torque of the motor as it accelerates to full speed may cause the tool to twist.

•

Wear eye and hearing protection. Always use safety glasses with side shields. Unless

otherwise speciﬁed, everyday glasses provide only limited impact resistance, they are not safety glasses.

Use only certiﬁed safety equipment; eye protection equipment should comply with ANSI z87.1 standards.

Protective hearing equipment should comply with ANSI s3.19 standards.

• Bits, sockets and tool get hot during operation. Wear gloves when touching them.

•

Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule

will reduce the risk of personal injury.

•

Always disconnect battery pack from tool or place the switch in the locked or off position

before any assembly, adjustments or changing of accessories. Following this instruction will reduce the risk

of serious personal injury.

•

Do not place battery tools or their batteries near ﬁre or heat. This will reduce the

risk of explosion and possibly personal injury.

•

Never use a battery which has been dropped or received a sharp blow. A

damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.

•

Use designated battery pack (Genesis™ -Model GLAB20A) and charger

(Genesis™- Model GLACH20AS) for this tool. Use of any other batteries may result in a

risk of ﬁre.

WARNING: Read and understand safety and operating instructions of

designated battery and charger before using this tool. This manual contains important

safety and operating instruction for battery charger.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER &

BATTERY

• Save These Instructions. This manual contains important safety and operating instructions for

your battery charger.

•

Before Using the battery Charger, read all instructions and cautionary markings on (1) Battery

Charger, (2) Battery, and (3) Product using battery.

•

Use only the charger which accompanied your product or direct replacements as listed in this

manual. Do not substitute any other charger.

•

Do not recharge battery in damp or wet environments. Do not expose battery pack to

water or rain.

•

Do not operate charger with damaged cord or plug. Replace immediately.

•

Do not operate charger if it has received a sharp blow, been dropped or otherwise

damaged in any way. Take it to a qualiﬁed serviceman.

•

Do not disassemble charger or battery pack. Take it to a qualiﬁed serviceman when

service or repair is required. Incorrect reassembly may result in a risk of electric shock or ﬁre.

•

Do not charge battery pack when temperature is below 50 degrees F (10 degrees C) or above

104 degrees F (40 degrees C). Store tool and battery pack in a location where temperature will not exceed

122 degrees F (50 degree C). This is important to prevent serious damage to the battery cells.

•

Place charger on ﬂat non-ﬂammable surface and away from ﬂammable materials when

re-charging the battery pack.

•

To reduce risk of electric shock, unplug charger from outlet before attempting any

maintenance or cleaning.

• I

f operating time has become excessively shorter, stop operating immediately. It may

result in a risk of overheating, possible burns and even an explosion.

7

English

• Battery leakage may occur under extreme usage or temperature conditions. Avoid contact with

skin and eyes. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets

into your eyes, wash them out with clear water for at least 10 minutes, and then seek medical attention right

away.

•

Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.

•

Do not short the battery pack. Do not touch the terminal with any conductive material. Avoid

storing battery pack in a container with other metal objects such as nails, coins, etc. Always protect the battery

terminals when battery pack is not used.

•

Do not charge battery pack inside a box or container of any kind. The battery

must be placed in a well ventilated area during charging.

•

Do not allow anything to cover or clog the charger vents.

• Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The

battery pack can explode in a ﬁre.

•

Disconnect Charger from the power source when not in use. This will reduce the

risk to electric shock or damage to the charger if metal pieces should fall into the opening. It also will help

prevent damage to the charger during a power surge.

WARNING: A battery short can cause a large current ﬂow, overheating, possible

burns and even a breakdown.

WARNING: 120 volts are present at charging terminals, do not probe with

conductive objects. Electric shock or electrocution may result. Do not allow any liquid to

get inside charger. Electric shock may result.

IMPORTANT BATTERY INFORMATION: DISPOSING OF THE BATTERY

• Your batteries are LITHIUM-ION rechargeable batteries. Certain Local, State and Federal

laws prohibit disposal of these batteries in ordinary trash.

• Consult your local waste authorities for your disposal/recycling options.

• More information regarding battery disposal in U.S. and Canada is available at;

http://www.rbrc.org/index.html, or by calling 1-800-822-8837 (1-800-8BATTERY).

KNOWING YOUR IMPACT DRIVER

1. Hex Keyless Chuck

2. Trigger Switch

3. Reversing Switch

4. LED Work Light

5. Battery Power Indicator

6. Battery Pack

7. Battery Locking Tab

8. Charger Adaptor

9. Charger Stand

10. Screwdriver Bit

FIG 1

9

8

7

3

2

5

4

1

10

6

English

20V Lithium-Ion Impact Driver

Operator’s Manual GLID20A

UNPACKING AND CONTENTS

IMPORTANT: Due to modern mass production techniques, it is unlikely the tool is

faulty or that a part is missing. If you ﬁnd anything wrong, do not operate the tool until

the parts have been replaced or the fault has been rectiﬁed. Failure to do so could result

in serious personal injury.

CONTENTS IN PACKAGE

Description Q'ty Description Q'ty

OPERATION

WARNING:

To reduce the risk of serious personal injuries, read and follow all

important safety warning and instructions before using this tool.

WARNING: Always be sure that the tool

is switched off before insertion or removal of the

battery pack.

INSTALLING OR REMOVING THE

BATTERY PACK (FIG 2)

• To install the battery pack, slide the battery pack (1) into the

bottom of the tool housing (2) all the way until it locks in place

with a click, as shown in FIG 2. Lightly pull on the battery to

ensure it is locked into place and will not accidentally fall out of

the tool, causing an injury.

• To remove the battery pack, pull the battery pack away from the

tool while depressing the battery locking tab (3).

CHARGING THE BATTERY (FIG 3)

NOTE:

Always Check that the power supply corresponds to

the voltage on the ratings plate.

• Connect the charger adaptor (1) and the charger stand (3).

• Plug the charger adaptor (1) into a 120 Volt AC Power Source.

The green light on the charger stand (3) will illuminate,

indicating the charger is powered.

• Slide the battery (2) all the way into the charger stand (3) until

it locks in place with a click, as shown in FIG 3. The red light

on the charger stand will illuminate, indicating that the battery

is charging.

• The red light will go off after charging is complete.

• Batteries may become warm while charging. This is normal.

• If battery is hot after continuous use in the tool, allow it to cool down to room temperature before charging. This

will extend the life of your batteries.

NOTE: It takes approximately 3-5 hours to charge up a completely discharged battery.

WARNING: Always disconnect the battery pack from the tool or place the switch

in the locked or off position before any assembly, adjustments or changing accessories.

FIG 2

2

1

3

2

3

FIG 3

1

2

3

Impact Driver 1

Charger Adaptor 1

Charger Stand 1

Bit 1

Operator's Manual 1

9

English

TRIGGER SWITCH ACTION

• Turn the driver on by depressing the trigger switch (2-FIG 1).

• Depressing the switch further will produce more speed and torque.

• Use the reversing switch (3-FIG 1) to change the direction of rotation of the driver.

• The reversing switch has three positions: Forward, Reverse, and Off (middle).

• Always check the rotation before beginning your work.

LED WORK LIGHT

Your tool has a built-in LED work light to illuminate the work area. When you turn on the tool, the work light will

automatically turn on.

BATTERY POWER INDICATOR

Your tool has a built-in battery power indictor (5-FIG 1) right above the trigger switch. It has three colored lights-

Green, Yellow and Red. Depress the trigger switch slightly to check the battery power level. When all three lights

illuminate, it indicates the battery is at full power. The battery is at half full power when only the yellow and

red lights illuminate. When the red light illuminates only, it indicates that the battery is at low power level and

requires immediate charging.

ELECTRIC BRAKE

This driver is equipped with an electric brake. The electric brake provides you with another element of control

during various operations. If the tool consistently fails to quickly stop after trigger switch release, have a

qualiﬁed serviceman examine the tool.

1/4" HEX CHUCK (FIG 4)

• Your driver is equipped with a tool-less 1/4" Hex Chuck, so you

can quickly change bits with no extra tools required.

• Remove battery pack or place the Forward/Reverse Switch in

the center (OFF) position.

• To insert or change bits, pull the chuck locking sleeve (A) away

from the tool. Hold it with one hand while inserting the bit with

the other hand. Release the locking sleeve to lock the bit in

place.

• Always make sure that bit is seated ﬁrmly by pulling on the

bit. Never attempt to operate a bit that is wobbly, unstable, or

broken.

• To remove the bit, pull the chuck locking sleeve away from the

tool, remove the bit and release the sleeve.

NOTE: Only use Impact-Quality Bits with a locking groove.

APPLICATION

WARNING:

The Impact Driver is NOT intended to be used as a drill.

WARNING:

The Impact Driver is NOT a torque wrench. Do not use this tool

for tightening fasteners to speciﬁed torques.

GENERAL SCREWDRIVING

1. Clamp your workpiece.

2. Drill pilot holes for larger screws or when driving screws into hardwoods.

3. Exert enough pressure to start the screw and keep it turning. Do not force the screw. Let the tool do the work.

4. Use a speed that will not strip the screw head or break the screw. Maintain your balance.

FIG 4

A

English

20V Lithium-Ion Impact Driver

Operator’s Manual GLID20A

MAINTENANCE

CLEANING

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING: Do not at any time let brake ﬂuids, gasoline, petroleum-based

products, penetrating oils, etc., come in contact with plastic parts. Chemicals can

damage, weaken or destroy plastic which may result in serious personal injury.

Electric tools used on ﬁberglass material, wallboard, spackling compounds, or plaster are subject to accelerated

wear and possible premature failure because the ﬁberglass chips and grindings are highly abrasive to bearings,

brushes, commutators, etc. Consequently, we do not recommended using this tool for extended work on these

types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool

using compressed air.

LUBRICATION

This tool is permanently lubricated at the factory and requires no additional lubrication.

TWO-YEAR WARRANTY

This product is warranted free from defects in material and workmanship for 2 years after date of purchase. This

limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser

is covered by this warranty and it is not transferable. Prior to returning your tool to store location of purchase,

please call our Toll-Free Help Line for possible solutions.

THE BATTERY INCLUDED IS WARRANTED FOR 1 YEAR AS DESCRIBED ABOVE.

THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.

ACCESSORIES INCLUDED IN THIS KIT ARE NOT COVERED BY THE 2 YEAR WARRANTY.

TOLL-FREE HELP LINE

For questions about this or any other GENESIS™ Product, please call Toll-Free: 888-552-8665.

Or visit our web site: www.genesispowertools.com

Richpower Industries, Inc.

736 Hampton Road

Williamston, SC 29697

Printed in China, on recycled paper

Page is loading ...

31

Español

GARANTÍA DE DOS AÑOS

Este producto está garantizado contra defectos de material y de fabricación durante 2 años a partir de la fecha de

compra. Esta garantía limitada no cubre el desgaste normal o daños por negligencia o accidente. El comprador

original está cubierto por esta garantía y no es transferible. Antes de devolverlo su herramienta para almacenar la

ubicación de la compra, por favor llame gratis a la línea de ayuda para las posibles soluciones.

EL PAQUETE DE BATERÍAS INCLUIDA ES UNA GARANTÍA DE 1 AÑO, COMO SE HA DESCRITO

ANTERIORMENTE.

ESTE PRODUCTO NO ESTÁ GARANTIZADO SI SE UTILIZA PARA PROPÓSITOS INDUSTRIALES O

COMERCIALES.

LOS ACCESORIOS INCLUIDOS CON ESTE JUEGO NO TIENEN 2 AÑOS DE GARANTÍA.

LÍNEA DE AYUDA GRATUITA

Para preguntas acerca de este o cualquier otro producto GENESIS Llame gratuitamente al teléfono:

888-552-8665.

O visite nuestro sitio web: www.genesispowertools.com

Richpower Industries, Inc.

736 Hampton Road

Williamston, SC 29697

Printed in China, on recycled paper

Richpower Industries, Inc.

736 Hampton Road

Williamston, SC USA

www.genesispowertools.com

2015.08. V01

Genesis GL20DIDKA2 User manual

This manual is also suitable for

Genesis GL20DIDKA2 User manual

in other languages

Related papers

Other documents