Genelec 8030 Operating instructions

Brand: Genelec

Model: 8030

Category: Soundbar speakers

Type: Operating instructions

This manual is also suitable for

Page is loading ...

2 English

General description

The bi-ampliﬁed GENELEC 8030A is a two way

active monitoring loudspeaker designed to be small

but still have high output, low coloration, and broad

bandwidth.

The 8030A is ideal for near ﬁeld monitoring,

mobile vans, broadcast and TV control rooms, sur-

round sound systems, home studios, multimedia

applications and also for use with computer sound-

cards. As an active loudspeaker, it contains driv-

ers, power ampliﬁers, active crossover ﬁlters and

protection circuitry. The MDE™ (Minimum Diffrac-

tion Enclosure™) loudspeaker enclosure is made

of die-cast aluminium and shaped to reduce edge

diffraction. Combined with the advanced Direc-

tivity Control Waveguide

(DCW

), this design

provides excellent frequency balance in difﬁcult

acoustic environments. If necessary, the bass

response of the 8030A’s can be extended with a

Genelec 7050B or 7060B subwoofer.

Positioning the loudspeaker

Each 8030A monitor is supplied with an integrated

ampliﬁer unit, mains cable and an operating manual.

After unpacking, place the loudspeaker in its required

listening position, taking note of the line of the acous-

tic axis. The axes of all loudspeakers should converge

at ear height at the listening position (see Figure 1).

Connections

Before connecting up, ensure that the mains

switch is off and the volume control fully counter-

clockwise. These controls are located on the front

panel of the loudspeaker. Do not connect the loud-

8030A

Active Monitoring System

English 3

speaker to an unearthed mains supply or using an

unearthed mains cable.

Audio input is via a 10 kOhm balanced female

XLR connector labelled “INPUT”. An unbalanced

source may be used as long as pin 3 is grounded

to pin 1 at the unbalanced source connector (see

Figure 2).

The male XLR “OUTPUT” connector can be

used for daisy-chaining up to six 8030A’s together

or for connecting a Genelec 7050B subwoofer. The

volume control attenuates the signal on this output,

so the ﬁrst “master” loudspeaker on a daisy-chain

can be used to adjust the level on the whole chain.

The volume controls on the “slave” loudspeakers

should be set fully clockwise.

Once the connections have been made, the

loudspeakers are ready to be switched on.

Setting the volume control

The input sensitivity of the loudspeaker can be

matched to the output of the audio signal source by

adjusting the volume control on the front panel.

Setting the tone controls

The frequency response of Genelec 8030A can

be adjusted to match the acoustic environment by

setting the tone control switches on the rear panel.

The controls are “Treble Tilt”, “Bass Tilt” and “Bass

Roll-Off”. An acoustic measuring system such as

WinMLS is recommended for analyzing the effects

of the adjustments, however, careful listening with

suitable test recordings can also lead to good results

if a test system is not available. Table 1 shows some

typical settings in various situations. Figure 4 shows

the effect of the controls on the anechoic response.

Figure 1: Location of the acoustic

axis

Figure 2: Type of cable needed if

unbalanced source is used (ex-

ample shown is RCA output to the

XLR input)

Figure 3: Control and connector layout on the rear panel of

the 8030A.

190 mm

ACOUSTIC

AXIS

> 0,7 m

4 English

Treble Tilt

Treble Tilt (switch 1) attenuates the treble response

above 5 kHz by 2 dB, which can be used for smooth-

ening down an excessively bright sounding system.

Bass Tilt

Bass Tilt offers three attenuation levels for the bass

response below 1 kHz, usually necessary when the

loudspeakers are placed near room boundaries.

The attenuation levels are -2 dB (switch 3 “ON”), -4

dB (switch 4 “ON”) and -6 dB (both switches “ON”).

Bass Roll-Off

Bass Roll-Off (switch 2) activates high-pass ﬁlter-

ing at 85 Hz to complement the low-pass ﬁlter on

a Genelec 7050B subwoofer. This switch should

always be set to “ON” when using the 8030A with

7050B subwoofers.

The factory setting for all tone controls is “OFF” to

give a ﬂat anechoic response. Always start adjust-

ment by setting all switches to “OFF” position. Mea-

sure or listen systematically through the different

combinations of settings to ﬁnd the best frequency

balance.

Mounting considerations

Align the loudspeakers correctly

Always place the loudspeakers so that their acous-

tic axes (see ﬁgure 1) are aimed towards the listen-

ing position. Vertical placement is preferable, as it

minimises acoustical cancellation problems around

the crossover frequency.

Maintain symmetry

Check that the loudspeakers are placed symmetri-

cally and at an equal distance from the listening

position. If possible, place the system so that the lis-

tening position is on the centerline of the room and

the loudspeakers are placed at an equal distance

from the centerline.

Minimise reﬂections

Acoustic reﬂections from objects close to the loud-

speakers like desks, cabinets, computer monitors

etc. can cause unwanted blurring of the sound

image. These can be minimised by placing the loud-

speaker clear of reﬂective surfaces. For instance,

putting the loudspeakers on stands behind and

above the mixing console usually gives a better

result than placing them on the meter bridge.

Table 1: Suggested tone control settings for differing acoustical environments

Loudspeaker Mounting Position Treble Tilt Bass Tilt Bass Roll-Off

Flat anechoic response OFF OFF OFF

Free standing in a damped room OFF OFF OFF

Free standing in a reverberant room OFF -2 dB OFF

Near ﬁeld or console bridge OFF -4 dB OFF

Near to a wall OFF -6 dB OFF

With a 7050B subwoofer See above See above ON

English 5

Minimum clearances

Sufﬁcient cooling for the ampliﬁer and function-

ing of the reflex port must be ensured if the

loudspeaker is installed in a restricted space

such as a cabinet or integrated into a wall

structure. The surroundings of the loudspeaker

must always be open to the listening room with

a minimum clearance of 5 centimeters (2”)

behind, above and on both sides of the loud-

speaker. The space adjacent to the amplifier

must either be ventilated or sufﬁciently large to

dissipate heat so that the ambient temperature

does not rise above 35 degrees Celsius (95°F).

Mounting options

The 8030A offers several mounting options: The Iso-

Pod™ (Isolation Positioner/Decoupler™) vibration

insulating table stand allows tilting the loudspeaker

for correct alignment of the acoustic axis. The stand

can be attached to three mounting points allowing

vertical and symmetrical horizontal positioning. On

the base of the loudspeaker is a 3/8” UNC threaded

hole compatible with a standard microphone stand.

On the rear there are two M6x10 mm threaded

holes for Omnimount

size 20.5 brackets.

Maintenance

No user serviceable parts are to be found within

the ampliﬁer unit. Any maintenance or repair of the

8030A unit should only be undertaken by qualiﬁed

service personnel.

Safety considerations

Although the 8030A has been designed in accord-

ance with international safety standards, the fol-

lowing warnings and cautions should be observed

to ensure safe operation and to maintain the loud-

speaker under safe operating conditions:

• Servicing and adjustment must only be

performed by qualiﬁed service personnel. The

loudspeaker must not be opened.

• Do not use this product with an unearthed

mains cable as this may compromise

electrical safety.

• Do not expose the loudspeaker to water or mois-

ture. Do not place any objects ﬁlled with liquid,

such as vases on the loudspeaker or near it.

• This loudspeaker is capable of producing sound

pressure levels in excess of 85 dB, which may

cause permanent hearing damage.

• Free ow of air behind the loudspeaker is nec-

essary to maintain sufficient cooling. Do not

obstruct airﬂow around the loudspeaker.

• Note that the ampliﬁer is not completely discon-

nected from the AC mains service unless the

mains power cord is removed from the ampliﬁer

or the mains outlet.

Guarantee

This product is guaranteed for a period of two years

against faults in materials or workmanship. Refer to

supplier for full sales and guarantee terms.

6 English

Figure 4. The curves

show the effect of the

“Bass Tilt”, “Treble Tilt”

and “Bass Roll-Off” con-

trols on the free ﬁeld re-

sponse of the 8030A

Figure 5. The upper

curve group shows the

horizontal directivity

characteristics of the

8030A measured at

1 m. The lower curve

shows the system's

power response.

100

20k

100

200

500

1k 2k

10k

Genelec Oy 8030A (dBr) vs freq (Hz) 6 Apr 04

0°

60°

15°

30°

45°

100

20k

100

200

500

1k 2k

10k

Genelec Oy 8030A (dBr) vs freq (Hz) 6 Apr 04

BASS ROLL-OFF

TREBLE TILT

BASS TILT

English 7

AMPLIFIER SECTION

Bass amplifier output power with an 8 Ohm load: 40 W

Treble amplifier output power with an 8 Ohm load: 40 W

Long term output power is limited by driver unit protection

circuitry.

_____________________________________________

Amplifier system distortion at nominal output:

THD < 0.05 %

SMPTE-IM < 0.05 %

CCIF-IM < 0.05 %

DIM 100 < 0.05 %

_____________________________________________

Signal to Noise ratio, referred to full output:

Bass > 100 dB

Treble > 100 dB

_____________________________________________

Mains voltage: 100, 120, 220 or 230 V

according to region

Voltage operating range: ±10 %

Power consumption:

Idle 10 VA

Full output 80 VA

SYSTEM SPECIFICATIONS

Lower cut-off frequency, –3 dB: < 55 Hz

_____________________________________________

Upper cut-off frequency, –3 dB: > 21 kHz

_____________________________________________

Free field frequency response of system:

58 Hz – 20 kHz (± 2.0 dB)

_____________________________________________

Maximum short term sine wave acoustic output on axis in

half space, averaged from 100 Hz to 3 kHz:

@ 1 m > 100 dB SPL

@ 0.5 m > 106 dB SPL

_____________________________________________

Maximum long term RMS acoustic output in same

conditions with IEC weighted noise (limited by driver unit

protection circuit): @ 1 m > 97 dB SPL

_____________________________________________

Maximum peak acoustic output per pair on top of

console, @ 1 m distance with music material: > 108 dB

_____________________________________________

Self generated noise level in free field @ 1 m on axis:

< 10 dB (A-weighted)

_____________________________________________

Harmonic distortion at 85 dB SPL @ 1 m on axis:

Freq: 50…100 Hz < 2 %

>100 Hz < 0.5 %

_____________________________________________

Drivers: Bass 130 mm (5") cone

Treble 19 mm (

") metal dome

Both drivers are magnetically shielded

_____________________________________________

Weight: 5.6 kg (12.3 lb)

_____________________________________________

Dimensions: Height 299 mm (11

”)

(including Iso-Pod™ table stand)

Height 285 mm (11

”)

(without Iso-Pod™ table stand)

Width 189 mm (7

Depth 178 mm (7”)

CROSSOVER SECTION

Connectors: Input: XLR female, balanced 10 kOhm,

pin 1 gnd, pin 2 +, pin 3 -

Output: XLR male, balanced 100 Ohm,

pin 1 gnd, pin 2 +, pin 3 -

_____________________________________________

Input level for 100 dB SPL output at 1 m:

-6 dBu at volume control max

_____________________________________________

Volume control range: -80 dB relative to max output

Output signal level is 0 dB relative to input signal level

but adjustable by volume control

_____________________________________________

Crossover frequency, Bass/Treble: 3.0 kHz

_____________________________________________

Treble Tilt control operating range:

0 to –2 dB @ 15 kHz

_____________________________________________

Bass Roll-Off control operating in a –6 dB step @ 85 Hz

(to be used in conjunction with a 7050B subwoofer)

_____________________________________________

Bass Tilt control operating range in –2 dB steps:

0 to –6 dB @ 100 Hz

_____________________________________________

The ‘CAL’ position is with all tone controls set to ‘off’ and

the input sensitivity control to maximum (fully clockwise).

EC DECLARATION OF CONFORMITY

This is to certify that the Genelec Monitoring System

8030A conforms to the following standards:

Safety: EN 60065: 2002 + A1:2006 + A11:2009/

IEC 60065:2001 7th Edition + A1: 2005

EMC: EN 55020 A2: 2008

EN 55013: (2001)+ A1 : 2003 + A2: 2009

EN 61000-3-2: 2006

EN 61000-3-3 A2: 2005

The product herewith complies with the requirements of

The Low Voltage Directive 2006/95/EC and EMC Directive

2004/108/EC

Signed:

Ilpo Martikainen

Position: Chairman of the Board

Date: 12-January-2009

Page is loading ...

Deutsch 13

VERSTÄRKER

Bass amplifier output power with an 8 Ohm load: 40 W

Treble amplifier output power with an 8 Ohm load: 40 W

Long term output power is limited by driver unit protection

circuitry.

_____________________________________________

Amplifier system distortion at nominal output:

THD < 0.05 %

SMPTE-IM < 0.05 %

CCIF-IM < 0.05 %

DIM 100 < 0.05 %

_____________________________________________

Signal to Noise ratio, referred to full output:

Bass > 100 dB

Treble > 100 dB

_____________________________________________

Mains voltage: 100, 120, 220 or 230 V

according to region

Voltage operating range: ±10 %

Power consumption:

Idle 10 VA

Full output 80 VA

FREQUENZWEICHE UND FILTER

Connectors: Input: XLR female, balanced 10 kOhm,

pin 1 gnd, pin 2 +, pin 3 -

Output: XLR male, balanced 100 Ohm,

pin 1 gnd, pin 2 +, pin 3 -

_____________________________________________

Input level for 100 dB SPL output at 1 m:

-6 dBu at volume control max

_____________________________________________

Volume control range: -80 dB relative to max output

Output signal level is 0 dB relative to input signal level

but adjustable by volume control

_____________________________________________

Crossover frequency, Bass/Treble: 3.0 kHz

_____________________________________________

Treble Tilt control operating range:

0 to –2 dB @ 15 kHz

_____________________________________________

Bass Roll-Off control operating in a –6 dB step @ 85 Hz

(to be used in conjunction with a 7050B subwoofer)

_____________________________________________

Bass Tilt control operating range in –2 dB steps:

0 to –6 dB @ 100 Hz

_____________________________________________

The ‘CAL’ position is with all tone controls set to ‘off’ and

the input sensitivity control to maximum (fully clockwise).

EG KONFORMITÄTSERKLÄRUNG

This is to certify that the Genelec Monitoring System

8030A conforms to the following standards:

Safety: EN 60065: 2002 + A1:2006 + A11:2009/

IEC 60065:2001 7th Edition + A1: 2005

EMC: EN 55020 A2: 2008

EN 55013: (2001)+ A1 : 2003 + A2: 2009

EN 61000-3-2: 2006

EN 61000-3-3 A2: 2005

The product herewith complies with the requirements of

The Low Voltage Directive 2006/95/EC and EMC Directive

2004/108/EC

Signed:

Ilpo Martikainen

Position: Chairman of the Board

Date: 12-January-2009

TECHNISCHE DATEN

Lower cut-off frequency, –3 dB: < 55 Hz

_____________________________________________

Upper cut-off frequency, –3 dB: > 21 kHz

_____________________________________________

Free field frequency response of system:

58 Hz – 20 kHz (± 2.0 dB)

_____________________________________________

Maximum short term sine wave acoustic output on axis in

half space, averaged from 100 Hz to 3 kHz:

@ 1 m > 100 dB SPL

@ 0.5 m > 106 dB SPL

_____________________________________________

Maximum long term RMS acoustic output in same

conditions with IEC weighted noise (limited by driver unit

protection circuit): @ 1 m > 97 dB SPL

_____________________________________________

Maximum peak acoustic output per pair on top of

console, @ 1 m distance with music material: > 108 dB

_____________________________________________

Self generated noise level in free field @ 1 m on axis:

< 10 dB (A-weighted)

_____________________________________________

Harmonic distortion at 85 dB SPL @ 1 m on axis:

Freq: 50…100 Hz < 2 %

>100 Hz < 0.5 %

_____________________________________________

Drivers: Bass 130 mm (5") cone

Treble 19 mm (

") metal dome

Both drivers are magnetically shielded

_____________________________________________

Weight: 5,6 kg (12.3 lb)

_____________________________________________

Dimensions: Height 299 mm (11

”)

(including Iso-Pod™ table stand)

Height 285 mm (11

”)

(without Iso-Pod™ table stand)

Width 189 mm (7

Depth 178 mm (7”)

Page is loading ...

Français 15

source, en tournant la commande de volume sur le

panneau avant de l’enceinte.

Réglage des commandes de

tonalité

La réponse en fréquences de la 8030A peut s’ac-

corder à l’environnement acoustique en ajustant

les commandes de tonalité sur l’arrière de l’en-

ceinte. Les commandes sont Treble Tilt, Bass

Tilt, et Bass Roll-Off. GENELEC recommande

l’utilisation d’un système de mesure acoustique

tel WinMLS pour analyser l’effet des ajustements,

bien que l’écoute critique avec un signal appro-

prié peut aussi donner d’excellents résultats si

un système de mesure n’était pas disponible. Le

tableau 1 montre des ajustements typiques dans

différentes situations. L’illustration 4 montre l’effet

des commandes sur la réponse en chambre ané-

choïque.

Commande Treble Tilt

Le sélecteur Treble tilt (commutateur 1) atténue de

2 dB la réponse en fréquence au delà de 5 kHz, ce

qui permet d’adoucir les systèmes trop stridents.

Commande Bass Tilt

Le circuit Bass Tilt procure trois niveaux d’atténua-

tion pour la réponse en basses fréquences sous 1

kHz, ce qui est habituellement nécessaire lorsque

l’enceinte est placée près des murs de la pièce. Les

niveaux d’atténuation disponibles sont -2 dB (com-

mutateur 3 en position ON), -4 dB (commutateur

4 en position ON), -6 dB (commutateurs 3 et 4 en

position ON).

Cable

Blindage

RCA

(Source)

XLR

(Enceinte)

Illustration 1: Position de l’axe

acoustique

Illustration 2: Cablage nécessaire pour

connexion à une source asymétrique

(example ci-dessus d’une sortie RCA

à une entrée XLR)

Illustration 3: Contrôles et disposition des connecteurs sur la

face arrière de la 8030A

MAINS INPUT

50/60Hz80W 230 V~

MAGNETICALLY SHIELDED

MADE IN FINLAND

8030A BI-AMPLIFIED

MONITORING SYSTEM

OUT

GND

SERIAL NUMBER

www.genelec.com

292-8030T-6

GND

BASS AND TREBLETILT

55 1k 5k 20k

L'INTÉRIEUR REMPLAÇABLEPA RL'UTILISATEUR.ADRESSER

TO WATEROR MOISTURE. NO USERSERVICEABLE PARTS

ELECTRIC SHOCKHAZARD. DO NOTOPEN.DO NOTSUBJECT

AVERTISSEMENT

RISQUE DECHOC ÉLECTRIQUE. NE PASOUVRIR.NEPAS

EXPOSERÀL'EAU OU L'HUMIDITÉ.AUCUN COMPOSANT À

TOUTERÉPARATIONÀUNPERSONNEL QUALIFIÉ. CET

APPAREIL DOITÊTRERACCORDÉÀLATERRE.

USE EARTHEDMAINS CONNECTION ONLY.

INSIDE. REFERSERVICING TO QUALIFIED PERSONNEL.

WARNING

292-8030W292-8030W

BASS ROLL-OFF-6dB 85Hz

55 85 500 Hz

ALL OFF

3+4

-6

TREBLETILT-2dB

ALL OFF

BASS ROLL-OFF

BASS TILT -6 dB

BASS TILT -2 dB

BASS TILT -4 dB

OFF

-6

-4

-2

ÉVENT ACCORDÉ

ORIFICES FILETÉS POUR

SUPPORT MURAL ET

SUPPORT DE PLAFOND

COMMANDES DE TONALITÉ

PANNEAU DE CONNEXION

(ACCÈS HORIZONTAL)

ISO-POD

SOCLE DE SUPPORT

190 mm

AXE

ACOUSTIQUE

> 0,7 m

Page is loading ...

Suomi 21

Herkkyyden säätö

Kaiuttimen ottoliitännän herkkyys (äänenvoi-

makkuus) voidaan säätää sopivaksi etuseinän

oikeassa alakulmassa olevalla voimakkuussääti-

mellä.

Taajuusvastesäätöjen käyttö

Kaiuttimen taajuusvastetta voidaan muokata kuun-

telutilan akustisista ominaisuuksista ja kaiuttimien

sijoituksesta johtuvien toistovirheiden kompensoi-

miseksi. Säätö tehdään kaiuttimen takapaneelissa

olevien “Treble Tilt”-, “Bass Tilt”- ja “Bass Roll-Off”-

kytkimien avulla. Kaikki säädöt asetetaan tehtaalla

asentoon “OFF”, mikä antaa tasaisen taajuusvas-

teen kaiuttomassa tilassa. Säätöjen vaikutus toisto-

vasteeseen on esitetty kuvassa 4.

Suosittelemme akustisen mittausjärjestelmän

(esim. WinMLS) käyttöä kaiuttimien säätämisessä.

Ellei tällaista ole käytettävissä, säätö voidaan

tehdä myös korvakuulolta sopivia testiäänitteitä ja

-signaaleja hyväksikäyttäen. Taulukko 1 sisältää

muutamia suuntaa-antavia säätöesimerkkejä. Kai-

uttimien sijoitus ja akustinen ympäristö vaikuttaa

ratkaisevasti säätötarpeeseen, joten säätöön kan-

nattaa ryhtyä vasta kun kuuntelutilan järjestys on

saatu lopulliseen muotoonsa.

Treble Tilt

Treble Tilt-säätö (kytkin 1) vaimentaa kaiuttimen dis-

kanttitoistoa 5 kHz:n yläpuolella 2 dB, mitä voidaan

käyttää liian kirkkaalta tuntuvan toiston korjaami-

seen.

Kuva 1: Kaiuttimen akustisen akselin

sijainti.

Kuva 2: Balansoimattomaan RCA-

liittimeen liitettäessä tarvittavan väli-

kaapelin kytkentä.

Kuva 3: 8030A:n takapaneeli.

190 mm

AKUSTINEN

AKSELI

> 0,7 m

MAINS INPUT

50/60Hz80W 230 V~

MAGNETICALLY SHIELDED

MADE IN FINLAND

8030A BI-AMPLIFIED

MONITORING SYSTEM

OUT

GND

SERIAL NUMBER

www.genelec.com

292-8030T-6

GND

BASS ANDTREBLETILT

55 1k 5k 20k

L'INTÉRIEUR REMPLAÇABLEPA RL'UTILISATEUR.ADRESSER

TO WATEROR MOISTURE. NO USERSERVICEABLE PARTS

ELECTRIC SHOCKHAZARD. DO NOTOPEN.DO NOT SUBJECT

AVERTISSEMENT

RISQUE DECHOC ÉLECTRIQUE. NE PASOUVRIR.NEPAS

EXPOSERÀL'EAU OU L'HUMIDITÉ.AUCUN COMPOSANT À

TOUTERÉPARATIONÀUNPERSONNEL QUALIFIÉ. CET

APPAREIL DOITÊTRERACCORDÉÀLATERRE.

USE EARTHEDMAINS CONNECTION ONLY.

INSIDE. REFERSERVICING TO QUALIFIED PERSONNEL.

WARNING

292-8030W292-8030W

BASS ROLL-OFF-6dB 85Hz

55 85 500 Hz

ALL OFF

3+4

-6

TREBLETILT-2dB

ALL OFF

BASS ROLL-OFF

BASS TILT -6 dB

BASS TILT -2 dB

BASS TILT -4 dB

OFF

-6

-4

-2

REFLEKSIPUTKI

MUTTERIKIERTEET

RIPUSTUSTELINEILLE

TAAJUUSVASTESÄÄTIMET

LIITINPANEELI

Iso-Pod™

PÖYTÄJALUSTA

Page is loading ...

Svenska 27

Volymkontroll

Ingångskänsligheten hos 8030A kan anpassas till

utsignalen på ansluten mixer, eller annan signal-

källa, genom att man justerar volymkontrollen på

högtalarens framsida.

Inställning av tonkontrollerna

Frekvensåtergivningen hos Genelec 8030A kan

anpassas till den akustiska miljö, som den ska an-

vändas i, med hjälp av tonomkopplarna på baksi-

despanelen.

Dessa kontroller är Treble Tilt, Bass Tilt och Bass

Roll-Off. Ett akustiskt mätsystem, som till exempel

WInMLS, rekommenderas för att analysera effek-

ten av de gjorda justeringarna, men en noggrann

lyssning, tillsammans med lämpliga testskivor, kan

ge goda resultat om inte ett testsystem ﬁnns till-

gängligt. Tabell 1 visar några typiska grundinställ-

ningar i olika lyssningssituationer. Bild 4 visar ef-

fekten av kontrollinställningarna i ett ekofritt rum.

Treble Tilt

Treble Tilt-kontrollen (switch 1) sänker diskantåtergiv-

ningen hos högtalaren vid frekvenser över 5 kHz med

2 dB. Detta kan användas för att mjuka upp återgiv-

ningen hos ett system som låter vasst i diskanten.

Bass Tilt

Bass Tilt-kontrollen erbjuder tre olika dämpnivåer

vid 2 kHz hos högtalaren, ofta nödvändigt när hög-

talaren placeras nära en vägg eller liknande. Dämp-

nivåerna är -2 dB (switch 3 ON), -4 dB (switch 4 ON)

och -6 dB (båda switcharna ON).

Figur 1: Bestämning av den

akustiska axeln

Figur 2: Kabeltyp som behövs om

obalanserad ljudkälla används

(i detta exempel en RCA-utgång

kopplad till XLR-ingången)

Figur 3: Kontrollernas och anslutningarnas placering på

8030A:s baksidespanel.

190 mm

AKUSTISK

AXEL

> 0,7 m

MAINS INPUT

50/60Hz80W 230 V~

MAGNETICALLY SHIELDED

MADE IN FINLAND

8030A BI-AMPLIFIED

MONITORING SYSTEM

OUT

GND - +

SERIAL NUMBER

www.genelec.com

292-8030T-6

+ - GND

BASS AND TREBLETILT

55 1k 5k 20k

L'INTÉRIEUR REMPLAÇABLEPA RL'UTILISATEUR. ADRESSER

TO WATEROR MOISTURE. NO USER SERVICEABLE PARTS

ELECTRIC SHOCKHAZARD. DO NOTOPEN.DO NOT SUBJECT

AVERTISSEMENT

RISQUE DECHOC ÉLECTRIQUE. NE PASOUVRIR.NEPAS

EXPOSERÀL'EAU OU L'HUMIDITÉ. AUCUNCOMPOSANT À

TOUTERÉPARATIONÀUNPERSONNEL QUALIFIÉ. CET

APPAREIL DOITÊTRERACCORDÉÀLA TERRE.

USE EARTHEDMAINS CONNECTION ONLY.

INSIDE. REFERSERVICING TO QUALIFIED PERSONNEL.

WARNING

292-8030W292-8030W

BASS ROLL-OFF -6dB 85Hz

55 85 500 Hz

ALL OFF

3+4

-6

TREBLETILT-2dB

ALL OFF

BASS ROLL-OFF

BASS TILT -6 dB

BASS TILT -2 dB

BASS TILT -4 dB

OFF

-6

-4

-2

BASREFLEXPORT

GÄNGADE HÅL

FÖR TAK OCH

VÄGGFÄSTEN

TONKONTROLLER

KONTAKTPANEL

MED

NÄTSTRÖMBRYTARE

(HORISONTAL)

Iso-Pod™

GUMMIFOT

Page is loading ...

Genelec Document D0036R001a Copyright Genelec Oy 4.2010. All data subject to change without prior notice

www.genelec.com

International enquiries

Genelec, Olvitie 5

FI 74100, Iisalmi, Finland

Phone +358 17 83881

Fax +358 17 812 267

Email [email protected]

In Sweden

Genelec Sverige

Ellipsvägen 10B

P.O. Box 5521,

S-141 05 Huddinge

Phone +46 8 449 5220

Fax +46 8 708 7071

Email [email protected]

In the USA

Genelec, Inc., 7 Tech Circle

Natick, MA 01760, USA

Phone +1 508 652 0900

Fax +1 508 652 0909

Email [email protected]

In China

Beijing Genelec Audio Co.Ltd

Jianwai SOHO, Tower 12,

Room 2605

D-1504, Chaoyang District

Beijing 100022, China

Phone +86 10 8580 2180

Fax +86 10 8580 2181

Email [email protected]

Genelec 8030 Operating instructions

Brand: Genelec

Model: 8030

Category: Soundbar speakers

Type: Operating instructions

This manual is also suitable for

Download PDF

report

in other languages

français: Genelec 8030 Mode d'emploi
Deutsch: Genelec 8030 Bedienungsanleitung
svenska: Genelec 8030 Bruksanvisningar
suomi: Genelec 8030 Käyttö ohjeet

Genelec 8030 Operating instructions

This manual is also suitable for

Genelec 8030 Operating instructions

in other languages

Related papers

Other documents