BLACK+DECKER STB3620L User manual

Page is loading ...

6

ENGLISH

(Original instructions)

Intended use

Your BLACK+DECKER STB3620L trimmer has been

designed for trimming and nishing lawn edges and to cut

grass in conned spaces. This appliance is intended for

consumer use only.

Safety instructions

Warning! When using mains-powered

appliances, basic safety precautions,

including the following, should always be

followed to reduce the risk of re, electric

shock, personal injury and material dam-

age.

Warning! When using the machine the

safety rules must be followed. For your

own safety and bystanders please read

these instructions before operating the

machine. Please keep the instructions

safe for later use.

u Read all of this manual carefully before

operating the appliance.

u The intended use is described in this

manual. The use of any accessory

or attachment or the performance

of any operation with this appliance

other than those recommended in this

instruction manual may present a risk

of personal injury.

u Retain this manual for future refer-

ence.

Using your appliance

Always take care when using the appli-

ance.

u Always use safety glasses or goggles.

u Never allow children or people unfa-

miliar with the instructions to use the

appliance.

u Do not allow children or animals to

come near the work area or to touch

the appliance or power supply cord.

u Close supervision is necessary when

the appliance is used near children.

u This appliance is not intended for use

by young or inrm persons without

supervision.

u This appliance is not to be used as a

toy.

u Only use the appliance in daylight or

good articial light.

u Use in a dry location only. Do not allow

the appliance to become wet.

u Avoid using the appliance in bad

weather conditions, especially when

there is a risk of lightning.

u Do not immerse the appliance in water.

u Do not open the body casing. There

are not user-serviceable parts inside.

u Do not operate the appliance in

explosive atmospheres, such as in the

presence of ammable liquids, gases

or dust.

u To reduce the risk of damage to plugs

or cords, never pull the cable to re-

move the plug from a socket.

u The appliance is only to be used with

the power supply unit provided with the

appliance.

Safety of others

u This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sen-

sory or mental capabilities or lack of

experience and knowledge if they have

been given supervision or instruction

concerning use of the appliance in a

safe way and understand the hazards

involved. Children shall not play with

the appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

u Children must be supervised to ensure

that they do not play with the

appliance.

Residual risks.

Additional residual risks may arise when

using the tool which may not be included

in the enclosed safety warnings.

7

ENGLISH

(Original instructions)

These risks can arise from misuse, pro-

longed use etc.

Even with the application of the relevant

safety regulations and the implementa-

tion of safety

devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotat-

ing/moving parts.

u Injuries caused when changing any

parts, blades or accessories.

u Injuries caused by prolonged use

of a tool. When using any tool for

prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing

dust developed when using your tool

(example:- working with wood, espe-

cially oak, beech and MDF.)

After use

u When not in use, the appliance should

be stored in a dry, well ventilated place

out of reach of children.

u Children should not have access to

stored appliances.

u When the appliance is stored or trans-

ported in a vehicle it should be placed

in the boot or restrained to prevent

movement following sudden changes

in speed or direction.

Inspection and repairs

u Before use, check the appliance for

damaged or defective parts. Check for

breakage of parts and any other condi-

tions that may affect its operation.

u Do not use the appliance if any part is

damaged or defective.

u Have any damaged or defective parts

repaired or replaced by an authorised

repair agent.

u Never attempt to remove or replace

any parts other than those specied in

this manual.

Additional safety instructions for

grass trimmers

Warning! Cutting elements continue to

rotate after the motor is switched off.

u Be familiar with the controls and the

proper use of the appliance.

u Before use, check the power supply

cord and extension cord for signs of

damage, ageing and wear. If a cord

becomes damaged during use, discon-

nect the cord from the mains supply

immediately. DO NOT TOUCH THE

CORD BEFORE DISCONNECTING

THE SUPPLY.

u Always remove the battery from the

appliance whenever the appliance is

unattended, before clearing a block-

age, before cleaning and maintenance,

after striking a foreign object or when-

ever the appliance starts vibrating

abnormally.

u Do not use the appliance if the cords

are damaged or worn.

u Wear stout shoes or boots to protect

your feet.

u Wear long trousers to protect your

legs.

u Before using the appliance, check that

your cutting path is free from sticks,

stones, wire and any other obstacles.

u Only use the appliance in the upright

position, with the cutting line near the

ground. Never switch the appliance on

in any other position.

u Move slowly when using the appliance.

Be aware that

freshly cut grass is

damp and slippery.

8

ENGLISH

(Original instructions)

u Do not work on steep slopes. Work

across the face of slopes, not up and

down.

u Never cross gravel paths or roads

while the appliance is running.

u Never touch the cutting line while the

appliance is running.

u Do not put the appliance down until the

cutting line

has come to a complete

standstill.

u Use only the appropriate type of cut-

ting line. Never use metal cutting line

or shing line.

u Be careful not to touch the line trim-

ming blade.

u Take care to keep the mains cable

away from the cutting line. Always be

aware of the position of the cable.

u Keep hands and feet away from the

cutting line at all times, especially

when switching on the motor.

u Before using the appliance and after

any impact, check for signs of wear or

damage and repair as necessary.

u Never operate the appliance with

damaged guards or without guards in

place.

u Take care against injury from any de-

vice tted for trimming the lament line

length. After extending new cutter line

always return the machine to its nor-

mal operating position before switching

on.

u Always ensure that the ventilation slots

are kept clear of debris.

u Do not use the lawn trimmer (edge

trimmer), if the cords are damaged or

worn.

u Keep extension cords away from cut-

ting elements.

Additional safety instructions for

batteries and chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not store in locations where the

temperature may exceed 40 °C.

u Charge only at ambient temperatures

between 10 °C and 40 °C.

u Charge only using the charger pro-

vided with the tool.

u When disposing of batteries, follow

the instructions given in the section

"Protecting the environment".

Chargers

u Use your BLACK+DECKER charger

only to charge the battery in the tool

with which it was supplied. Other bat-

teries could burst, causing personal

injury and damage.

u Never attempt to charge non-recharge-

able batteries.

u Have defective cords replaced immedi-

ately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

$

The charger is intended for

indoor use only.

Read the instruction manual

before use.

Electrical safety

#

Your charger is double insu-

lated; therefore no earth wire is

required. Always check that the

mains voltage corresponds to the

voltage on the rating plate. Never

attempt to replace the charger

unit with a regular mains plug.

9

ENGLISH

(Original instructions)

u If the supply cord is damaged, it must

be replaced by the manufacturer or an

authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Labels on appliance

The following warning symbols are found on the appliance

along with the date code:

Read the manual prior to operation.

Wear safety glasses or goggles when operating

this appliance.

N

Wear suitable ear protectors when operating this

appliance.

Always remove the battery from the appliance

before performing any cleaning or maintenance .

K

Beware of ying objects. Keep bystanders away

from the cutting area.

R

Do not expose the appliance to rain or high

humidity.

Directive 2000/14/EC guaranteed sound power.

Features

This appliance includes some or all of the following features.

1. Variable speed trigger

2. Handle

3. Lock off button

4. Battery

5. Charge indicator

6. Auxiliary handle

7. Height adjust locking clamp

8. Trimmer head

9. Head rotate button

10. Edge guide

11. Guard

12. Spool housing

13. Spool cap

Assembly

Warning! Before assembly, make sure that the tool is

switched off and the battery has been removed.

Fitting the guard (Fig. D & E)

u Remove the screw (E1) from the Guard

u Keeping the Guard square to the trimmer head slide it fully

into place until the retaining tab clicks. Ensure that the

guide rails (D1) on the Guard (11) are correctly aligned

with the guide rails (D2) on the trimmer head (D3) (Figure

D). The locking tab (D4) should be snapped into the hous-

ing slot (D5).

u Secure the guard with the screw (E1) (Figure E).

Warning! Never use the tool unless the guard is properly

tted.

Attaching the auxiliary handle (Fig. F&G)

u Push the Auxiliary handle (F1) onto the tube (F2).

u Slide the bolt (G1) into the hex-shaped hole in the handle

and through to the opposite side.

u Tighten the knob (G2) onto the bolt by turning it clockwise.

Warning! Ensure that central rib is located into slot in tube.

Adjusting the position of the auxiliary handle

(Fig.G)

The auxiliary handle (6) can be adjusted to provide optimum

balance and comfort.

u Loosen the knob (G2) on the bolt (G1) by turning it

counter-clockwise.

u Gently slide the auxiliary handle up or down the tube (F2)

to the desired height for comfort.

u Tighten the knob (G2) onto the bolt by (G1) turning it

clockwise.

Adjusting the height of the tool (Fig.H)

Adjust the length of the trimmer to obtain proper working posi-

tion as shown in Figure M.

This tool has a telescopic mechanism, allowing you to set it to

a comfortable height.

To adjust the height setting, proceed as follows:

u Release the height adjust locking clamp (7).

u Gently pull the tube (H1) up or down to the desired height.

u Close the height adjust locking clamp (7).

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

Warning! Before assembly, remove the battery from the tool.

u Remove the tape holding the cutting line to the spool

housing (12).

Fitting and removing the battery (Fig.B,C)

u To t the battery (4), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button while at

the same time pulling the battery out of the receptacle.

96

10

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace.

Do not overload.

Charging the battery

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell tempera-

ture is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell temperature

warms up or cools down.

u Plug the charger into an appropriate outlet before inserting

the battery pack.

u Insert the battery pack into the charger.

The green LED will ash indicating that the battery is being

charged.

The completion of charge is indicated by the green LED

remaining on continuously. The pack is fully charged and

may be used at this time or left in the charger

Warning! Recharge discharged batteries as soon as pos-

sible after use or battery life may be greatly diminished.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad Battery

The charger can detect a weak or damaged battery. The

red LED ashes in the pattern indicated on the label. If you

see this bad battery blink pattern, do not continue to charge

the battery. Return it to a service centre or a collection site

for recycling

Hot/Cold Pack Delay

When the charger detects a battery that is excessively

hot or excessively cold, it automatically starts a Hot/Cold

Pack delay, suspending charging until the battery has

normalised. After this happens, the charger automatically

switches to the Pack Charging mode. This feature ensures

maximum battery life. The red LED ashes in the pattern

indicated on the label when the Hot/Cold pack delay is

detected.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

State of Charge Indicator

The battery is equipped with a state of charge indicator.

This can be used to display the current level of charge in the

battery while in the trimmer and during charging. It does not

indicate appliance functionality and is subject to variation

based on product components, temperature and end user

application.

Checking State of Charge during use

u Press the state of charge indicator (A1).

u The four LEDs (A2) will illuminate indicating the percent of

charge in the battery (Fig.A.)

u If LED light does not illuminate, charge battery.

Switching on and off

u To switch the trimmer on, press in and hold the lock off

button (3).

u Depress the variable speed trigger (1). The trimmer's

speed, power and runtime depend on how far you press

the trigger. Lightly depressing the trigger will result in

lower speed and power, but longer runtime. Fully depress-

ing the trigger will result in maximum speed and power,

but shorter runtime.

u To switch the trimmer off, release both the trigger and the

lock off button.

Warning! Never attempt to lock the on/off button in the on

position.

Operating the trimmer

u With the unit on, angle unit and slowly swing the trimmer

side to side as shown in (Fig.M).

u Maintain a cutting angle of 5° to 10° as shown in gure

M1. Do not exceed 10° (Fig.M2). Cut with the tip of the

line. To keep distance from hard surfaces use edge guide

(10). Pull the guide out until it snaps securely into place

u Maintain a minimum distance of 60cm between the guard

and your feet as shown in (Fig.M3). To achieve this

distance adjust the overall height of the trimmer as shown

in (Fig.H).

11

ENGLISH

(Original instructions)

Setting Trimming or Edging Mode (Fig.I, J

and K)

u The trimmer can be used in trimming mode as shown in

(Fig.I) or in edging mode to trim overhanging grass along

lawn edges and ower beds as shown in (Fig.K).

Trimming Mode (Fig.I and J)

For trimming mode, the trimmer head should be in the position

shown in gure I. If it is not:

u Remove the battery from the trimmer.

u Press and hold the head release button (9).

u While holding the auxiliary handle (6), rotate the head (8)

clockwise.

u Release the head release button.

u Lift the edge guide (10) into the closed position.

Edging Mode (Fig.K)

Warning! When being used as an edger, stones, pieces of

metal and other objects can be thrown out at high speed by

the line. The trimmer and guard are designed to reduce the

danger, however make sure that other persons and pets are at

least 30 metres away. For edging, the trimmer head should be

in the position shown in (Fig.K). If it is not:

u Remove the battery from the trimmer.

u Press and hold the head-release button (9) as shown in

(Fig. K).

u While holding the auxiliary handle (6), rotate the head (8)

counterclockwise.

u Release the head-release button.

u Drop the edge guide (10) in to the open position. Ensure

that the guide is all the way down, an audible click will be

heard.

Note: The head will only rotate in one direction.

Warning!Do not use the trimmer to create

edges or trenches.

u Guide the trimmer as shown in (Fig.N).

u To make a closer cut, slightly tilt the trimmer.

Hints for optimum use

uUse the tip of the string to do the cutting; do not force

string head into uncut grass.

u Wire and wooden fences cause extra string wear, even

breakage. Stone and brick walls, kerbs and wood will

wear string rapidly. Take care to reduce contact with hard

surfaces.

u Do not allow spool cap to drag on ground or other sur-

faces.

uIn long growth cut from the top down and do not exceed

30cm in height.

uKeep trimmer tilted toward the area being cut; this is the

best cutting angle

uThe trimmer cuts when passing the unit from the right to

the left. This will avoid throwing debris at the operator.

uAvoid trees and shrubs. Tree bark, wood mouldings, siding

and fence posts can easily be damaged by the string.

Clearing Jams and Tangled Line Fig.O, P, Q

Warning! Remove the battery from the trimmer before making

any assembly adjustments or changing accessories. Such

preventive safety measurements reduce the risk of starting the

appliance accidentally. From time to time, especially when cut-

ting thick or stalky weeds, the line feeding hub may become

clogged with sap or other material and the line will become

jammed as a result. To clear the jam follow the steps below.

uPress the release tabs on the line spool cap as shown in

(Fig.O) and remove the cap by pulling it straight off.

uPull the nylon line spool out and clear any broken line or

debris from the spool area.

uPlace spool and line into spool cap with line "parked" in

slots provided as shown in (Fig.P1).

uInsert the line end through the appropriate hole in the

spool cap. Pull slack line through until it pulls out of the

holding slots as shown in (Fig.P2).

uPress the spool down gently and rotate it until you feel it

drop into place. When in place the spool will turn a few

degrees left and right freely.

uTake care to keep the line from becoming trapped under

the spool

uAlign the spool caps tabs with the slots on the spool hous-

ing (Fig.P).

uSnap the spool cap back on ensuring the lugs snap into

spool housing.

Note: The line should protrude approximately 122mm from

the housing.

Replacing the Spool Fig.O, P, Q and R

uRemove battery from trimmer.

uDepress the tabs and remove the spool cap from the

spool housing on the trimmer head (Fig.O).

uGrasp empty spool with one hand and spool cap with

other hand and pull spool out.

uReplace spool with BLACK+DECKER model A6482-XJ.

uRemove any dirt and grass from the spool and spool cap.

uIf lever (R1) in base of spool cap becomes dislodged,

replace in correct position before inserting a new spool as

shown in (Fig.R).

uUnfasten the end of the cutting line and guide the line into

the eyelet (P2).

uPress the spool gently into the spool cap and rotate it until

you feel it drop into place. Then push to snap into place.

When in place the spool will turn a few degrees left and

right freely.

uTake care to ensure that the line does not become trapped

under the spool.

uAlign the spool cap tabs with the slots on the spool hous-

ing (g Q).

uSnap the spool cap back on ensuring the lugs snap into

spool housing.

Note: The line should protrude approximately 122mm from

the housing.

Rewinding spool from bulk line (use only 2.0mm

ROUND diameter line) (Fig.S)

Bulk line is also available for purchase from your local retailer.

To install bulk line, follow the steps below:

uRemove battery from trimmer.

12

ENGLISH

(Original instructions)

u Remove the empty spool from the trimmer as described in

“Replacing the spool”.

uRemove any remaining cutting line from the spool.

uMake a fold at the end of the cutting line at about 19mm

(S1). Feed the cutting line into one of the line anchoring

slots (S3).

uMake sure the line is pulled tight against the spool and

begin to wind the cutting line onto the spool in the direc-

tion of the arrow on the spool

uMake sure to wind the line on neatly and in layers. Do not

crisscross (Fig.T).

uWhen the wound cutting line reaches the recesses (S4),

the spool is full.

uLocate line into 'parked' slot provided (Fig.P1). Cut line

from bulk reel.

uFit the spool onto the trimmer as described in “Replac-

ing the spool” gures O,P,Q and R.

NOTE: Hand wound spools from bulk line are likely to become

tangled more frequently than BLACK+DECKER factory

wound spools. For best results, factory wound spools are

recommended.

Replacement spools:

#A6486-XJ (3pcs SA spool and line)

#A6482-XJ (1pcs SA spool and line)

Auto Feed System (AFS)

The string trimmer is tted with AFS spool, which will detect

when the string breaks and re-feed automatically. Do not

bump or pull the string. If the AFS is not feeding properly,

remove spool and check the wire is wound correctly and

re-insert into tool.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory opera-

tion depends upon proper tool/appliance care and regular

cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

uRegularly clean the cutting line and spool using a soft

brush or dry cloth.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Troubleshooting

Problem

Solution

Appliance runs slowly.

Fully depress the variable speed trigger.

The level of trigger depression affects

speed.

Remove battery from trimmer

Check that the spool housing can rotate

freely. Carefully clean it if necessary.

Check that the cutting line does not pro-

trude more than approximately 122mm

from the spool. If it does, trim it so that it

just reaches the line trimming blade.

Automatic line feed does not

feed line.

More line is fed when the line shortens

to approximately 76mm. To determine if

the line is not feeding, let line wear past

this point.

Keep the tabs depressed and remove the

spoolcap with the spool from the spool

housing in the trimmer head.

Ensure that the line is not crisscrossed

on the spool as detailed in (Fig.T). If it

is unwind the cutting line and rewind

it neatly.

Inspect tracks at the bottom of spool for

damage. If damageed, replace spool.

Pull the cutting line until it protrudes

approximately 122mm from the spool. If

insufcient cutting line is left on the spool,

install a new spool of cutting line.

Align the tabs on the spool cap with the

cut outs in the housing.

Push the spool cap onto the housing until

it snaps securely into place.

If the cutting line protrudes beyond the

trimming blade, cut it off so that it just

reaches the blade. If the automatic line

feed still does not work or the spool is

jammed, try the following suggestions:

Carefully clean the spool and housing.

Make sure you are using correct line size

and diameter (2.00 mm) - smaller and

larger line sizes will affect the functional-

ity of the auto feed system.

Remove the spool and check if the lever

in the spool housing can move freely.

Remove the spool and unwind the cutting

line, then wind it on neatly again. Replace

the spool into the housing.

Overfeeding

Ensure you are cutting with the tip of the

line 177mm from the spool. Use the edge

guide if needed to ensure proper space

is maintained.

Ensure you are not axceeding a 10º an-

gle as shown in (Fig.M). Avoid contact of

the line with hard surfaces such as brick,

concrete, wood etc. This will prevent

excessive wear and/or overfeed of line.

Cut with the tip of the line

Line unravels when cap or

spool is removed

Make sure to park the lines in holding

slots (gure P) before removing.

13

ENGLISH

(Original instructions)

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your BLACK+DECKER product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

z

Separate collection of used products and packag-

ing allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or

by the retailer when you purchase a new product.

BLACK+DECKER provides a facility for the collection and re-

cycling of BLACK+DECKER products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local BLACK+DECKER ofce at the

address indicated in this manual. Alternatively, a list of author-

ised BLACK+DECKER repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

Batteries

Z

At the end of their useful life, discard batteries with

due care for our environment:

u Run the battery down completely, then remove it from the

tool.

u NiCd, NiMH and Li-Ion batteries are recyclable. Place

the battery(s) in a suitable packaging to ensure that the

terminals cannot be short-circuited. Take them to any

authorised repair agent or a local recycling station.

u Do not short-circuit the battery terminals.

u Do not dispose of the battery(s) in a re as this may result

in a risk of personal injury or an Explosion.

Technical data

STB3620L

H 1

Input Voltage

V

AC

36V

No-Load Speed

min

-1

0 - 7200/min

Weight

kg

3.4kg

Battery BL2036

Voltage

V

dc

36V

Capacity

Ah

2.0Ah

Type

Li-Ion

Charger LCS36 Type 1

Input Voltage

V

AC

220 - 240V

Output Voltage

V

DC

36V

Current

mA

A

Input: 600mA

Output: 1,3A

Hand/arm weighted vibration value according to

EN 50636-2-91:

= < 2,5 m/s

2

, uncertainty (K) = 1,5 m/s

2

.

L

PA

(sound pressure) 75 dB(A)

uncertainty (K) = 1.5 dB(A)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

%

STB3620L Cordless String Trimmer

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1:2012 + A11:2014

EN 50636-2-91:2014

2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VIII

DEKRA Certication B.V., Utrechtseweg 310,

6802 ED Arnhem, The Netherlands

Notied Body ID No.: 0344

Level of acoustic power according to 2000/14/EC

14

ENGLISH

(Original instructions)

(Article 12, Annex III, L ≤ 50 cm):

L

WA

(measured sound power) 95 dB(A)

uncertainty (K) = 1.5 dB(A)

L

WA

(guaranteed sound power) 96 dB(A)

These products also comply with Directive 2014/108/EC (until

19.04.2016), 2014/30/EU (from 20.04.2016) and 2011/65/EU.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

R. Laverick

Engineering Manager

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

06/08/2015

Guarantee

Black & Decker is condent of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to

faulty materials, workmanship or lack of conformity, within

24 months from the date of purchase, Black & Decker guar-

antees to replace defective parts, repair products subjected

to fair wear and tear or replace such products to ensure

minimum inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent

by contacting your local Black & Decker ofce at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-

sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to register

your new BLACK+DECKER product and to be kept up to date

on new products and special offers. Further information on the

BLACK+DECKER brand and our range of products is avail-

able at www.blackanddecker.co.uk

Page is loading ...

België/Belgique/Luxembourg Stanley Black & Decker Belgium BVBA Tel. NL +32 15 47 37 65

www.blackanddecker.be Egide Walschaertsstraat 16 Tel. FR +32 15 47 37 66

enduser[email protected] 2800 Mechelen Fax. +32 15 47 37 99

Danmark Black & Decker [email protected]

Roskildevej 22 www.blackanddecker.dk

2620 Albertslund

Deutschland Stanley Black & Decker Deutschland Gmbh Tel. 06126 21-0

www.blackanddecker.de Black & Decker Str. 40, D - 65510 Idstein Fax 06126 21-2980

[email protected]

Ελλάδα StanleyBlack&Decker(ΕΛΛΑΣ)Ε.Π.Ε Τηλ. 210-8981616

www.blackanddecker.gr ΓΡΑΦΕΙΑ:Στράβωνος7&Βουλιαγμένης Φαξ 210-8983570

[email protected] 16674Γλυφάδα-Αθήνα

SERVICE: ΗμεροςΤόπος2-ΧάνιΑδάμ Τηλ.Service 210-8985208

 19300Ασπρόπυργος-Αθήνα Φαξ 210-5597598

España Stanley Black & Decker Ibérica, S.C.A. Tel. 934 797 400

www.blackanddecker.es Parc de Negocis “Mas Blau” Fax 934 797 419

[email protected] EdicioMuntadas,c/Bergadá,1,Of.A6

 08820ElPratdeLlobregat(Barcelona) 

France Black&Decker(France)S.A.S. Tel. 0472203920

www.blackanddecker.fr 5 allée des Hêtres Fax 04 72 20 39 00

B.P. 30084

69579 Limonest Cédex

Helvetia ROFOAG Tel. 026-6749393

www.blackanddecker.ch Gewerbezone Seeblick Fax 026-6749394

[email protected] 3213 Kleinbösingen

Italia Stanley Black & Decker Italia Tel. 039-9590200

www.blackanddecker.it Via Energypark 6 Fax 039-9590313

[email protected] 20871Vimercante(MB) Numeroverde800-213935

Nederland Stanley Black & Decker Netherlands BV Tel. +31 164 283 065

www.blackanddecker.nl HoltumNoordweg35,6121REBORN Fax +31164283200

enduser[email protected] Postbus83,6120ABBORN

Norge Black & Decker [email protected]

Postboks 4613, Nydalen www.blackanddecker.no

 0405Oslo  

Österreich Stanley Black & Decker Austria GmbH Tel. 01 66116-0

www.blackanddecker.at Oberlaaerstraße248,A-1230Wien Fax 0166116-614

[email protected]

Portugal Black & Decker Limited SARL Tel. 214667500

www.blackanddecker.pt Quinta da Fonte - Edifício Q55 D. Diniz Fax 214667580

[email protected] Rua dos Malhões, 2 e 2A - Piso 2 Esquerdo

2770 - 071 Paço de Arcos

Suomi Black&Decker asiakaspalvelu.@sbdinc.com

 PL47 www.blackanddecker.

00521, Helsinki

Sverige Black & Decker AB [email protected]

Box 94, 431 22 Mölndal www.blackanddecker.se

Türkiye KALEHırdavatveMakinaA.Ş. Tel. 02125335255

www.blackanddecker.com.tr DefterdarMah.SavaklarCad.No:15 Fax. 02125331005

 Edirnekapı/Eyüp/İstanbul34050 

United Kingdom & Black & Decker Tel. 01753 511234

Republic Of Ireland 210 Bath Road Fax 01753 512365

www.blackanddecker.co.uk Slough, Berkshire SL1 3YD

[email protected]

Middle East & Africa Black & Decker Tel. +971 4 8863030

www.blackanddecker.ae P.O.Box-17164 Fax +97148863333

[email protected] JebelAliFreeZone(South),Dubai,

UAE

90627509 REV-0

08/2015

BLACK+DECKER STB3620L User manual

BLACK+DECKER STB3620L User manual

in other languages

Related papers

Other documents