DeWalt DW099E Owner's manual

Please read these instructions before operating the product.

www.dewalt.eu

DW099E & DW099S

User Manual

DW099E

GB

NL

GR

I

FIN

D

DK

ES

NO

F

SE

PT

TR

Page is loading ...

4

GB

Contents

• User Safety

• Battery Safety

• Setup (Load Batteries)

• Operation

• Warranty

• Error Codes

• Specications

Retain all sections of this manual for future

reference.

User Safety

WARNING:

Carefully read the Safety Instructions and

Product Manual before using this product.

The person responsible for the product must

ensure that all users understand and adhere to

these instructions.

WARNING:

The following label information is placed on

your laser tool to inform you of the laser class

for your convenience and safety.

DW099S

FCC ID: 2ADA6DW099S

IC: 12409A-DW099S

DW099E

The DW099E and DW099S tools emit a visible laser

beam, as shown in Figure

A

#1. The laser beam

emitted is Laser Class 2 per IEC 60825-1 and complies

with 21 CFR 1040.10 and 1040.11 except for deviations

pursuant to Laser Notice No. 50, dated June 24, 2007.

WARNING:

While the laser tool is in operation, be careful

not to expose your eyes to the emitting laser

beam (red light source). Exposure to a laser

beam for an extended time period may be

hazardous to your eyes. Do not look into the

beam with optical aids.

WARNING: To reduce the risk of injury, user

must read the Product User manual, Laser

Safety manual, and Battery Safety information.

DeWalt, Slough, Bershire SL1 3YD, UK herewith

declares that the product DW099E/DW099S is in

compliance with the essential requirements and all

other provisions of Directive 1999/5/EC. Please contact

DeWalt for Declaration of Conformity.

Battery Safety

WARNING: Batteries can explode or leak and

cause serious injury or re. To reduce the risk:

ALWAYS follow all instructions and warnings

on the battery label and package.

DO NOT short any battery terminals.

DO NOT charge alkaline batteries.

DO NOT mix old and new batteries. Replace

all of them at the same time with new batteries

of the same brand and type.

DO NOT mix battery chemistries.

DO NOT dispose of batteries in re.

ALWAYS keep batteries out of reach of

children.

ALWAYS remove batteries if the device will not

be used for several months.

NOTE: Ensure that the recommended

batteries are used.

NOTE: Ensure the batteries are inserted in the

correct manner, with the correct polarity.

Setup (Load Batteries)

1.

Locate the battery compartment latch on the back

of the tool (Figure

C

#2).

2.

Using your finger, pull the latch up to unlock and

remove the battery door (Figure

D

#1 and #2).

3.

Insert two AAA batteries, making sure to position

the - and + ends of each battery as noted inside the

battery compartment (Figure

D

#3).

4.

Slide the pins at the bottom of the battery door into

the notches in the battery compartment

(Figure

D

#4).

5.

Push the battery door down until it snaps in place

(Figure

D

#5).

When the tool is ON, the battery level appears in the

display window (Figure

E

#1).

5

GB

Operation

Measuring Distance to a Wall or Object

1.

Click (Figure

A

#5) to turn on the tool.

2.

The tool will measure the distance from the bottom

of the tool to the wall or object (Figure

F

#1).

To measure from the top of the tool instead of the

bottom (Figure

F

#2), hold for 2 seconds.

On the display window, the tool icon will change

from

to (Figure

E

#5).

3.

Point the laser at the top of the tool (Figure

A

#1)

toward the wall or object whose distance you need

to measure (Figure

F

).

4.

Click to measure the distance from the tool

to the wall or object.

5.

At the bottom of the display window (Figure

A

#2),

view the current measurement (Figure

E

#3).

To take a new measurement, click

to move the

current measurement up to the previous line on the

display window (Figure

E

#2). Then repeat steps 2-5.

Measuring Distances Continuously

To take a series of measurements as you move

around, change to Continuous Measure mode.

1.

Click (Figure

A

#5) to turn on the tool.

2.

Point the laser at the top of the tool (Figure

A

#1)

toward the wall or object whose distance you need

to measure (Figure

F

).

3.

Click and hold for 2 seconds to turn on the

Continuous Measure mode.

4.

At the bottom of the display window

(Figure

A

#2), view the current measurement

(Figure

E

#3), which will keep changing as you

move the tool.

5.

To take the current measurement (from the tool to

the wall or object) and exit Continuous Measure

mode, click

.

To take a new measurement, click

to move the

current measurement up to the previous line on the

display window. Then repeat steps 2-5.

Measuring Area

You can measure the area of a wall, floor, or object.

1.

Click (Figure

A

#5) to turn on the tool.

2.

The tool will measure the distance from the bottom

of the tool to the wall or object (Figure

F

#1).

To measure from the top of the tool instead of the

bottom (Figure

F

#2), hold for 2 seconds.

On the display window, the tool icon will change

from

to (Figure

E

#5).

3.

Click to show on the display window

(Figure

E

#4).

4.

Measure the width.

• Point the top of the tool at one side of the target

(wall, floor, or object).

• Position the tool at one end of the target and

point the laser dot across the width. (Figure

G

#1 shows where to position the tool if you are

measuring from the bottom of the tool.)

• Click

to display the width measurement at

the top of the display window.

5.

Measure the length.

• Position the tool at one end of the target and

point the laser dot across the length. (Figure

G

#2 shows where to position the tool if you are

measuring from the bottom of the tool.)

• Click

to display the length measurement

on the second line of the display window.

6.

View the Area measurement at the bottom of the

display window (Figure

E

#3).

6

GB

Measuring Volume

You can measure the volume of a room or object.

1.

Click (Figure

A

#5) to turn on the tool.

2.

The tool will measure the distance from the bottom

of the tool to the wall or object (Figure

F

#1).

To measure from the top of the tool instead of the

bottom (Figure

F

#2), hold for 2 seconds.

On the display window, the tool icon will change

from

to (Figure

E

#5).

3.

Click twice to show on the display

window (Figure

E

#4).

4.

Measure the width.

• Point the top of the tool at one side of the target

(room or object).

• Position the tool at one end of the target and

point the laser dot across the width. (Figure

H

#1 shows where to position the tool if you are

measuring from the bottom of the tool.)

• Click

to display the width measurement at

the top of the display window.

5.

Measure the length.

• Position the tool at one end of the target and

point the laser dot across the length. (Figure

H

#2 shows where to position the tool if you are

measuring from the bottom of the tool.)

• Click

to display the length measurement

on the second line of the display window.

6.

Measure the height.

• Positon the tool at one end of the target and

point the laser dot across the height. (Figure

H

#3 shows where to position the tool if you are

measuring from the bottom of the tool).

• Click

to display the height measurement

on the third line of the display window.

7.

View the Volume measurement at the bottom of the

display window (Figure

E

#3).

Adding Measurements

You can add two measurements to get a total

measurement of the two distances.

1.

Click (Figure

A

#5) to turn on the tool.

2.

The tool will measure the distance from the bottom

of the tool to the wall or object (Figure

F

#1).

To measure from the top of the tool instead of the

bottom (Figure

F

#2), hold for 2 seconds.

On the display window, the tool icon will change

from

to (Figure

E

#5).

3.

Point the laser at the top of the tool (Figure

A

#1)

toward the wall or object whose distance you need

to measure.

4.

Click to measure the distance from the tool

to the wall or object.

5.

Indicate that you want to add this measurement to

the next measurement.

• On the DW099E keypad, click

(Figure

A

#7).

• On the DW099S keypad, click

(Figure

B

#1).

6.

Point the laser at the top of the tool toward the next

wall or object.

7.

Click to measure the distance and add it to

the previous measurement.

8.

View the total of the two measurements at the

bottom of the display window (Figure

E

#3).

7

GB

Subtracting Measurements

You can subtract one measurement from another.

1.

Click (Figure

A

#5) to turn on the tool.

2.

The tool will measure the distance from the bottom

of the tool to the wall or object (Figure

F

#1).

To measure from the top of the tool instead of the

bottom (Figure

F

#2), hold for 2 seconds.

On the display window, the tool icon will change

from

to (Figure

E

#5).

3.

Point the laser at the top of the tool (Figure

A

#1)

toward the wall or object whose distance you need

to measure.

4.

Click to measure the distance from the tool

to the wall or object.

5.

Indicate that you want to subtract the next

measurement from this measurement.

• On the DW099E keypad, click

twice.

• On the DW099S keypad, click

twice.

6.

Point the laser at the top of the tool toward the next

wall or object.

7.

Click to measure the distance and subtract it

from the previous measurement.

8.

View the difference between the two measurements

at the bottom of the display window (Figure

E

#3).

Changing the Unit of Measure

Once the current measurement is taken (the device is

not in Continuous Measure mode), you can change the

unit of measure from decimal ft (6.21 ft) to fractional ft

(6'02"

9/16), fractional ft to meters (1.894 m), meters to

inches (74

9/16 in), or inches to decimal ft.

• On the DW099E keypad, click

(Figure

A

#3).

• On the DW099S keypad, hold

(Figure

B

#1) until you see the measurement

change (2-3 seconds).

Using Your DW099S With

If you have a DW099S, you can use its Bluetooth

®

capability to pair it with the DeWALT Tool Connect

application on your cell phone or tablet, and then record

accurate measurements in your floor plans.

1.

From either or , download

the DeWALT Tool Connect application to your cell

phone or tablet.

2.

Using the DeWALT Tool Connect application,

capture the room or space for which you want to

record the measurements, and build your floor plan.

3.

On the DW099S keypad, click to turn on the

tool.

4.

If the Bluetooth

®

icon does not appear on the

display window (Figure

E

#6), click on the

keypad to turn on Bluetooth

®

.

5.

Use the DeWALT Tool Connect application to pair

your cell phone or tablet to the DW099S.

6.

Use the DW099S to measure each wall in the room

or space captured in the floor plan, and sync the

measurements to the floor plan.

7.

Using the DeWALT Tool Connect application, save

the floor plan.

Once you have saved the floor plan, you can export it

to one of several different file formats, including PDF,

DXF, or JPG, and print it or email it to other people (your

realtor, home center, etc.).

“THE BLUETOOTH

®

WORD MARK AND LOGOS ARE

REGISTERED TRADEMARKS OWNED BY BLUETOOTH

SIG, INC. AND ANY USE OF SUCH MARKS BY DEWALT

INDUSTRIAL TOOL CO. IS UNDER LICENSE. OTHER

TRADEMARKS AND TRADE NAMES ARE THOSE OF THEIR

RESPECTIVE OWNERS.”

Turning Off the Tool

The tool can be turned off in either of these ways:

• Press and hold

for several seconds (until the

display window clears).

• If you do not use the tool for 90 seconds, it will

automatically turn off.

8

GB

Three Year Limited Warranty

DeWALT will repair, without charge, any defects due

to faulty materials or workmanship for three years

from the date of purchase. This warranty does not

cover part failure due to normal wear or tool abuse.

For further detail of warranty coverage and warranty

repair information, visit www.DeWALT.com or call

1–800–4-DeWALT (1–800–433–9258). This warranty

does not apply to accessories or damage caused

where repairs have been made or attempted by others.

This warranty gives you specific legal rights and you

may have other rights which vary in certain states or

provinces.

In addition to the warranty, DeWALT tools are covered

by our:

1 YEAR FREE SERVICE

DeWALT will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first

year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance

of your DeWALT Power Tool, Laser, or Nailer for any

reason, you can return it within 90 days from the date of

purchase with a receipt for a full refund - no questions

asked.

RECONDITIONED PRODUCT: Reconditioned product

is covered under the 1 Year Free Service Warranty. The

90 Day Money Back Guarantee and the Three Year

Limited Warranty do not apply to reconditioned product.

FREE WARNING LABEL REPLACEMENT: If your

warning labels become illegible or are missing, call

1-800-4-DeWALT or visit your local service center for

a free replacement.

Protecting the Environment

Separate collection. This product must not

be disposed of with normal household

waste.

Should you nd one day that your DeWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

Separate collection of used products and

packaging allows materials to be recycled

and used again. Re-use of recycled

materials helps prevent environmental pollution and

reduces the demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

DeWALT provides a facility for the collection and

recycling of DeWALT products once they have

reached the end of their working life. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

DeWALT ofce at the address indicated in this

manual. Alternatively, a list of authorised DeWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com.

Batteries

• When disposing batteries, think of the protection

of the environment.

• Check with your local authorities for an

environmentally safe way of battery disposal.

9

GB

Error Codes

If INFO appears on the display window with a Code number, perform the corresponding Corrective Action.

Code Description Corrective Action

101 Received Signal Too Weak,

Measuring Time Too Long

Use the target plate or change the target surface.

102 Received Signal Too High Target is too reective. Use the target plate or change the target

surface.

201 Too Much Background Light Reduce the background light on the target area.

202 Laser Beam Interrupted Remove the obstacle and repeat the measurement.

203 Insufcient Power Replace the batteries.

301 Temperature Too High Allow the device to cool down to a temperature within

the specied Operating Temperature Range.

302 Temperature Too Low Allow the device to warm up to a temperature within

the specied Operating Temperature Range.

401 Hardware Error Switch the device on/off several times. If the error still occurs,

return the defective device to the Service Center or distributor.

Refer to the Warranty.

402 Unknown Error Contact the Service Center or distributor. Refer to the Warranty.

10

GB

Specications

Range .1m to 30m (4in to 100ft)

Measuring Accuracy* ± 2mm (± 3/32in)*

Resolution** 1mm (1/16in)**

Laser Class Class 2 (IEC/EN60825-1: 2014)

Laser Type ≤ 1.0mW @ 620-690nm

Laser/Backlight Automatic Switch-off After 30s

Unit Automatic Switch-off After 90s

Continuous Measuring Yes

Area/Volume Yes

Battery Life (2 x AAA) Up to 3000 Measurements (2500 with

)

Dimension (H x D x W) 120 x 48.5 x 26mm (4.72 x 1.91 x 1.02in)

Weight (with Batteries) 100g (3.21oz)

Storage Temperature Range -10° C ~ +60 C (14° F ~ 140° F)

Operating Temperature Range 0° C ~ +40° C (32° F ~ 104° F)

*Measuring Accuracy depends on the current conditions:

• Under favorable conditions (good target surface and room temperature), up to 10m (33ft).

• Under unfavorable conditions (bright sunlight, a very weak reecting target surface, or large temperature uctuations),

the error can increase by to ± 0.25mm/m (± 0.003 in/ft) for distances over 10m (33ft).

**Resolution is the nest measurement you can see. In inches, that is 1/16". In mm, that is 1mm.

Page is loading ...

DEWALT Europe, DEWALT D-65510 Idstein,

Germany 65509

Made in China

097395 - Rev A

July 2017

DeWalt DW099E Owner's manual

This manual is also suitable for

DeWalt DW099E Owner's manual

in other languages

Related papers

Other documents