Sony MEX-1GP is an in-car audio system that combines the convenience of modern connectivity with a wide range of audio playback options, allowing you to enjoy your favorite music and enhance your driving experience. Equipped with a CD/MD changer, you can seamlessly switch between your favorite discs and immerse yourself in a rich and dynamic sound. The USB port enables effortless connection to external storage devices, granting you access to a diverse collection of digital music files.
Sony MEX-1GP is an in-car audio system that combines the convenience of modern connectivity with a wide range of audio playback options, allowing you to enjoy your favorite music and enhance your driving experience. Equipped with a CD/MD changer, you can seamlessly switch between your favorite discs and immerse yourself in a rich and dynamic sound. The USB port enables effortless connection to external storage devices, granting you access to a diverse collection of digital music files.
丣嵓彂㌉♢ữ!
㱌!(-A)
•!∅⼩⚌彂㌉㒢⢋◌ᶯ↱彂㌉㌉⚔丣Ɂ
•!⍎㙭⚌ợ䒌⃩仒䗨㒢⢋◌㕚濇嫊㈉ㆱṾ⌵⅞⡔Ɂ
㌴䢞濃-B-
濄
剉壥彂㌉!3!⍔ㅺ㙘⡾!DE0NE!㋆䠃㚞濇⼩柟ợ䒌杗㷴彭㉍◌!
YB.D51濃曂斨彥濄Ɂ
丣嵓彂㌉♢!
!兗㯡廊愵⯂埌曆
棺€彂㌉渵凖㌉⚔⭠丣濇䂚⍲彂㌉㦽凖0䗡凖㛅丝ɀ渨凖ṉ⌮
丆凖䒙㷴廷⭠丣Ɂ
!兗䒙∌⢍丣㌋↚⭠丣ㅺ⢍丣⊫亍㒢⢋◌䗨䒙㷴⭠
丣
㱌
•!⣦㜀㰅㙭䒙∌⢍丣ㅺ⢍丣⊫亍◌濇ㅺ㙭ㆯ∌ẜ亍⢍丣濇
ⅽ㕄晤彂㌉㫈⭠丣Ɂ
•!剉㯡廊䗨⍲0Ἃ䌟䏧⃩㙭⃩仒!GN0BN!⢍丣濇孛⌦敩ĥ⃗ᷲ
㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝ĦɁ
!兗彭岑䗨∃䋫㒢⢋◌䗨!BNQ!SFNPUF!JO
㫈彂㌉ḩ彦䒌ᷲ∃䋫㒢⢋◌Ɂ彂㌉⃚⫧䱟乃⍓偡㋃⚳㚐㚞Ɂ
!兗廊廡䒙孁㌉⍇䒙乪
!兗㯡廊䃋㕲ὅ⍛
⼩柟棺€⭪渵凖㌉⚔⭠丣彂㌉兗㯡廊䗨愵⯂埌曆Ɂ
!兗!,23!W!䒙㷴䩓⪴濇孉䩓⪴⚌䀝㿏⃗斨Ṛằ仒
彾䒙
㱌
•!⣦㜀㰅㙭斨Ṛằ仒濇ⅽ彂㌉兗!,23!W!䒙㷴濃吨䒙㯄濄䩓
⪴濇孉䩓⪴旳㕚⡨ᷲ彾䒙䈚⽥Ɂ
!䟒ὁ棺€⭪渵凖㌉⚔⭠丣彂㌉兗㯡廊愵⯂埌曆Ɂ
•!剉㯡廊䗨⍲0Ἃ䌟䏧⃩㙭⃩仒!GN0BN!⢍丣濇孛⌦敩ĥ⃗ᷲ
㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝ĦɁ
!兗!,23!W!䒙㷴䩓⪴濇孉䩓⪴旳㕚⡨ᷲ彾䒙䈚⽥
䟒ὁ棺€⭪渵凖㌉⚔⭠丣彂㌉兗㯡廊愵⯂埌曆Ɂ
L
R
AUDIO OUT
FRONT
BUS
CONTROL IN
REMOTE
IN
2
4
5
6
7
1
3
AUD IO
OUT
REAR
AUD IO
OUT
FRONT
BUS
AUD IO
IN
BUS AUDIO IN
/AUX IN
*
2
AUDIO OUT
REAR
*
3
© 2006 Sony Corporation Printed in Thailand
2-661-372-31 (1)
Cautions
• This unit is designed for negative earth 12 V DC
operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Run all earth leads to a common earth point.
• Be sure to in su late any loose un con nect ed leads with
electrical tape for safety.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts Iist
• The numbers in the list are keyed to those in the
instructions.
• The bracket and the protection collar are
attached to the unit before shipping. Before mounting
the unit, use the release keys to remove the bracket
and the protection collar from the unit. For
details, see “Removing the protection collar and the
bracket ()” on the reverse side of the sheet.
• Keep the release keys for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket carefully to avoid injuring your
fi ngers.
Catch
Note
Before installing, make sure that the catches on both sides of
the bracket are bent inwards 2 mm. If the catches are straight
or bent outwards, the unit will not be installed securely and may
spring out.
Installation/Connections
⫭堩濊丣嵓彂㌉
Network Audio
System
Connection example
Notes (-
A
)
• Be sure to connect the earth lead before connecting the
amplifi er.
• The alarm will only sound if the built-in amplifi er is used.
Tip (-
B
-
)
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
Connection diagram
To a metal surface of the car
First connect the black earth lead, then connect the orange/
white stripped, yellow, and red power input leads.
To the power aerial control lead or power
supply lead of aerial booster amplifi er
Notes
• It is not necessary to connect this lead if there is no power
aerial or aerial booster, or with a manually-operated
telescopic aerial.
• When your car has a built-in FM/AM aerial in the rear/side
glass, see “Notes on the control and power supply leads.”
To AMP REMOTE IN of an optional power
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
To the interface cable of a car telephone
To a car’s illumination signal
Be sure to connect the black earth lead to a metal surface
of the car fi rst.
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black earth lead to a metal surface
of the car fi rst.
• When your car has a built-in FM/AM aerial in the rear/side
glass, see “Notes on the control and power supply leads.”
To the +12 V power terminal which is
energized at all times
Be sure to connect the black earth lead to a metal surface
of the car fi rst.
AUDIO OUT FRONT
AUDIO OUT REAR*
BUS AUDIO IN
BUS CONTROL IN
A
B
Equipment used in illustrations (not supplied)
㌶♢ᶑ䗨堩仒濃曂斨彥濄
from car aerial
㛉兎㯡廊⢍丣
Rear speaker
⍲㇐⡔◌
Front speaker
↱㇐⡔◌
Active subwoofer
㙭㷴峩愱Ẳ杗㇐⡔◌
Rotary commander RM-X4S
㔯廐忉㌋◌!SN.Y5T
Power amplifi er
∃䋫㒢⢋◌
× 2
× 4
CD/MD changer
DE0NE!㋆䠃㚞
BUS AUDIO IN
BUS CONTROL IN
Source selector*
杗㷴彭㉍◌*
XA-C40
* not supplied
! 曂斨彥
㱌び
•!㚐㚞⍎偡ợ䒌岃㛥㌉⚔䗨!23!W!䙘㲥䒙㷴Ɂ
•!≣ợ䒙丣⢝⚌圞揭ᵯ濇ㅺ亄⚌䥟∌恌Ṛᵮ濃⣦⸋㡩
㇚ㆯ濄Ɂ
•!彂㌉丣嵓ᶯ↱濇孛⃗救㯡廊䀝㿏⃗濇ṉ忣₱䝑
嵓Ɂ
•!⍎㙭彂㌉ᷪㆤ㙭⃚Ḻ⭠丣ᶯ⍲濇彂㌉渨凖⏰丆凖
䒙㷴廷⭠丣Ɂ
•!⭪ㆤ㙭⚔丣恡彂㌉↔⍰ᵤ㌉⚔䀝Ɂ
•!ᶞᷪ⫭濇孛∅⼩䒌乁乼做ⶊợㆤ㙭㛢㓇㚎彂㌉䗨
䒙丣乁乼Ɂ
⃗ᷲ䒙㷴丣濃渨凖濄䗨㱌びᷯ柝
•!⭪㚐㚞ᵲ⃚⫧䨯ặ⡔堩仒丨⍬ợ䒌㕚濇ㆤ彂㌉䗨㯡
廊䒙嵓⬝愳⼩柟⢋ᷲ⍨堩仒ὁ旍ᶁ⬝愳䗨⾟⏰Ɂ
•!⺷㯡廊䒙嵓⬝愳ᵱ⢃⢋㕚濇孛⭪㚐㚞䙘㌉ᵲ吨䒙㯄
䙜彂㌉Ɂ
晚Ṛᵤ夬埌!
•!埌ᶑ㓔⪻ᵲ存㕲᷊ᶑ䗨㓔⪻㖓ᵤ兘䗨Ɂ
•!堩⋜㒓㜚!!⏰ὁ㈈䌓!!㖓弴廷ᶯ↱堩⚌㚐堩
仒ᵮ䗨Ɂ⫭堩㚐堩仒ᶯ↱濇ợ䒌摥搉≽!!Ḳ
㚐堩仒ᵮ⌺ᵯ堩⋜㒓㜚!!⏰ὁ㈈䌓!!Ɂ孊个
⃩⬝濇孛⌦敩㚐柙⌱曆䗨ĥ㈪⋜ὁ㈈䌓⏰堩⋜㒓㜚!
)*ĦɁ
•!ὁ⪼⣡摥搉≽!!ṉ⡫⍲䒌Ɂ「Ḳ㯡廊ᵮ⌺ᵯ㚐
堩仒㕚濇㙭⼩壥䒌↔孉搉≽Ɂ
㱌び
⭳⼧ợ䒌堩⋜㒓㜚!
!ṉ₱Ẉ↔ㆯ㉫Ɂ
♞⫾䆫
㱌
⫭堩↱濇孛䟒嬈堩⋜㒓㜚!
!ᶈ弝䗨♞⫾䆫⍵⃩⺓㙖!3!nnɁ⣦㜀
♞⫾䆫䩸䙘ㅺ⍵⡺⺓㙖濇㚐堩仒⭪ᵱ偡䇆♞⫭堩ⷚ⍓偡⺝⅞Ɂ
*
1
RCA pin cord (not supplied)
*
2
Be sure to match the colour-coded cord for
audio to the appropriate jacks from the unit.
If you connect an optional CD/MD changer,
you cannot use AUX IN terminal.
*
3
AUDIO OUT can be switched SUB or
REAR. For details, see the Operating
Instructions.
*
4
Auxiliary optional equipment such as
portable DVD player (not supplied)
*
5
Supplied with the auxiliary equipment
*
6
Insert with the cord upwards.
*
1
!SDB!揬䒙丣濃曂斨彥濄
*
2
!䟒ὁ 杗柵⭠丣栀凖ᵲ堩仒ᵮ䗨㫇䟒㌶⪸䙜⭝
ⷸɁ⣦㜀彂㌉彭岑䗨!DE0NE!㋆䠃㚞濇ⅽ「
⭪㕄㰹ợ䒌!BVY!JO!䩓⪴Ɂ
*
3
!BVEJP!PVU!⍓Ⅻ㋆兗!TVC!ㅺ!SFBSɁ孊个⃩
⬝濇孛⌦敩斨ⶊ䗨ợ䒌存㕲᷊Ɂ
*
4
廩∍彭岑嬢⡫濇⣦ἣ㎞!EWE!㐑㒢㚞
濃曂斨彥濄
*
5
斨ⶊᷲ廩∍嬢⡫
*
6
䒙丣⍵ᵮ㌶
AMP REM
Max. supply current 0.3 A
㙤⢋䒙㲥!1/4!B
Fuse (10 A)
ὁ旍ᶁ!)21!B*
Blue/white striped
呁凖濊䗡凖㛅丝
Red
丆凖
Yellow
渨凖
White
䗡凖
Green
乣凖
Purple
䲏凖
White/black striped
䗡凖濊渵凖㛅丝
Grey/black striped
㿔凖濊渵凖㛅丝
Green/black striped
乣凖濊渵凖㛅丝
Grey
㿔凖
Left
ⵊ
Right
⍗
Left
ⵊ
Right
⍗
ANT REM
Black
渵凖
Blue
呁凖
Max. supply current 0.1 A
㙤⢋䒙㲥 1/2!B
Purple/black striped
䲏凖濊渵凖㛅丝
*
1
Source selector
(not supplied)
杗㷴彭㉍◌
)曂斨彥*
XA-C40
Supplied with the CD/MD changer
斨ⶊᷲ!DE0NE!㋆䠃㚞
*
1
ATT
ILLUMINATION
Orange/white striped
㦽凖濊䗡凖㛅丝
Light blue
㵅呁凖
*
6
MEX-1GP
Supplied with XA-C40
斨ⶊᷲ!YB.D51
* AUDIO OUT SUB/REAR
*
5
*
4
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V DC when
you turn on the tuner.
• When your car has built-in FM/AM aerial in the rear/side glass,
connect the power aerial control lead (blue) or the accessory
power input lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the earth lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
⃗ᷲ㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝
•!㌉彾孧孴◌䒙㷴㕚濇䒙∌⢍丣䗨㌋↚⭠丣濃呁凖濄ἣ偡㌴ỿ!
,23!W!䙘㲥䒙Ɂ
•!⺷㯡廊䗨⍲0Ἃ䌟䏧䧻ᵮ㙭⃩仒!GN0BN!⢍丣㕚濇孛⭪䒙∌⢍丣
㌋↚丣濃呁凖濄ㅺ廩∍䒙㷴廷䒙丣濃丆凖濄彂㌉兗䌔㙭⢍丣
⊫亍◌ᵮ䗨䒙㷴䩓⪴ᵮɁ孊个存㕲濇孛ᵲ「䗨丳摤⒪侸䱟Ɂ
•!㚐㚞ᵱ偡ợ䒌ᵱ⃛⡫之䒙◌䘶䗨䒙∌⢍丣Ɂ
ὁ㉥嬔⼪䗨丣嵓彂㌉㰹
⺷彂㌉ᷪ渨凖䗨䒙㷴廷䒙丣㕚濇⋗ợ䀝㿏⃗⃗救濇䒙㷴ḱ⭪
⭝嬔⼪䒙嵓ỿ䒙Ɂ
⃗ᷲ㇐⡔◌彂㌉䗨㱌びᷯ柝
•!彂㌉㇐⡔◌ᶯ↱濇孛⃗救㚐㚞䒙㷴Ɂ
•!孛ợ䒌斟ㇻᶞ!5.9!㪋⤪ᵸ⃛㙭崗⢃∃䋫⡨䍪偡⇿䗨㇐⡔◌濇ṉ
₱㋃⚳Ɂ
•!≣⭪㇐⡔◌䩓⪴彂㌉↔㯡廊ⷹ䘼ᵮ濇ㅺ⭪⍗㇐⡔◌䗨䩓⪴ᵲⵊ
㇐⡔◌䗨䩓⪴彂㌉Ɂ
•!≣⭪㚐㚞䗨㌉⚔丣彂㌉↔㇐⡔◌䗨岃㛥濃.濄䩓⪴ᵮɁ
•!㇐⡔◌ᵱ⍓ⷚ侸彂㌉Ɂ
•!孛ḩ彂㌉㕄㷴㇐⡔◌Ɂ⭪㙭㷴㇐⡔◌濃⃛㙭⃩仒㒢⢋
◌濄彂㌉
↔㇐⡔◌䩓⪴⍓偡Ṿ㋃⚳㚐㚞Ɂ
•!剉㚐㚞ợ䒌ⵊɀ⍗㇐⡔◌䗨⃕䒌岃㛥濃.濄䒙丣濇ᶞᷪ忣₱㒩
昀濇Ⅻ≣ợ䒌⫭堩⚌㯡廊⃩䗨⃩仒㇐⡔◌䒙丣Ɂ
•!孛≣⭪㚐㚞㇐⡔◌䒙丣䙜᷶彂㌉Ɂ
彂㌉䗨㱌びᷯ柝
⣦㜀㚎㫇䟒彂㌉㇐⡔◌⏰㒢⢋◌濇ⅽ㖢䢞⮳ᵮṾ⅞
䌔ĥGBJMVSFĦɁ弽㕚濇孛䟒ὁ㇐⡔◌⏰㒢⢋◌彂㌉㫇䟒Ɂ
12 3
182 mm
53 mm
Dashboard
Ṏ埌㛣
A TOYOTA
to dashboard/centre console
兗Ṏ埌㛣0ᶑ⢒㌋↚䬕
Bracket
ㆼ㜚
Bracket
ㆼ㜚
B NISSAN
to dashboard/centre console
兗Ṏ埌㛣0ᶑ⢒㌋↚䬕
Bracket
ㆼ㜚
Bracket
ㆼ㜚
Existing parts supplied with your car
旳㯡廊斨彥䗨䌔㙭恌Ṛ
AB
12
max. size
5 × 8 mm
㙤⢋⮞⭜
69!nn
max. size
5 × 8 mm
㙤⢋⮞⭜
69!nn
max. size
5 × 8 mm
㙤⢋⮞⭜
69!nn
max. size
5 × 8 mm
㙤⢋⮞⭜
69!nn
Face the hook
inwards.
損⪴曆⍵⃩Ɂ
Claws
⋅䆎
How to detach and attach the
front panel
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press .
Press , then slide the front panel to the right, and
gently pull out the left end of the front panel.
-B To attach
Place the hole of the front panel onto the spindle
on the unit, then lightly push the left side in.
Warning if your car’s ignition
has no ACC position
After turning the ignition off, be sure to press
and hold on the unit until the display
disappears.
Otherwise, the display does not turn off and this causes
battery drain.
RESET button
When the installation and connections are completed, be
sure to press the RESET button with a ballpoint pen, etc.,
after detaching the front panel.
Precautions
• Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe
and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket
Before installing the unit, remove the protection
collar and the bracket from the unit.
1 Remove the protection collar .
Engage the release keys together with the
protection collar .
Pull out the release keys to remove the
protection collar .
2 Remove the bracket .
Insert both release keys together between
the unit and the bracket until they click.
Pull down the bracket , then pull up the unit
to separate.
Mounting example
Installation in the dashboard
Notes
• Bend these claws outward for a tight fi t, if necessary (-
2
).
• Make sure that the 4 catches on the protection collar are
properly engaged in the slots of the unit (-
3
).
Mounting the unit in a Japanese
car
You may not be able to install this unit in some makes of
Japanese cars. In such a case, consult your Sony dealer.
Note
To prevent malfunction, install only with the supplied screws .
Orient the release key
correctly.
㫇䟒䟒⫾摥搉≽㔝⍵Ɂ
Existing parts supplied with your car
旳㯡廊斨彥䗨䌔㙭恌Ṛ
Fire wall
斖㿏⠥
1
2
A
B
ợ䒌↱㱌びᷯ柝
•!Ḹ个彭⌺⫭堩ằ仒濇ṉợ㚐堩仒ᵱⷖ㇔㫇䗨槢槚
㐱ỀɁ
•!忣₱⭪㚐㚞⫭堩⚌⌻㿔⭼濇㯅䇍⏰⺞䀬㊓∌⻕䗨
⊞❃濇ㅺ⫭堩⚌樼㶍⡨濇⣦䙘⭨斗₭ᵯㅺ䁑㭸䬅德
斨張Ɂ
•!ᶞᷪ⫭堩⫭⏰⍓曄濇⍎偡ợ䒌斨彥䗨⫭堩㛨ṚɁ
⫭堩夶⸊ᶯ孧㓘
孛⚌!56ṉ⃩孧㓘⫭堩夶⸊Ɂ
㈪⋜ὁ㈈䌓⏰堩⋜㒓㜚!
⫭堩㚐堩仒ᶯ↱濇孛€Ḳ㚐堩仒ᵮ⌺ᵯὁ㈈䌓!!
⏰堩⋜㒓㜚!Ɂ
1!!㈪⋜ὁ㈈䌓!Ɂ
!垸㌉摥搉≽!!⏰ὁ㈈䌓!Ɂ
!㈭⅞摥搉≽!!ṉ⌺ᵯὁ㈈䌓!Ɂ
2!!㈪⋜堩⋜㒓㜚!
Ɂ
!⭪!3!ᶎ摥搉≽!!㌶㚐堩仒⏰堩⋜㒓
㜚!!ᶯ敘䙘↔⎐夥ⓤ┶⡔Ɂ
!⍵ᵯ㈭堩⋜㒓㜚!
濇䂚⍲⍵ᵮ㈭⅞㚐堩仒
ṉἣⅪ䤟Ɂ
⫭堩䢞ữ!
⫭堩⚌Ṏ埌㛣愰
㱌
•!⣦㙭⼩壥濇⍵⡺⺓㙖⋅䆎ṉ䲋♞⫭堩濃.3濄Ɂ
•!孛䟒ὁὁ㈈䌓!!ᵮ䗨!5!ᶎ♞⫾䆫ᵲ㚐堩仒䗨⋅㥡㫇䟒垸㌉
濃.4濄Ɂ
⭪㚐㚞⫭堩ᷲ㕉㚐ḋ㯡廊ᵮ!
㙭䗨㕉㚐ḋ㯡廊ᵱ偡⫭堩㚐㚞Ɂ⚌弽䤱〩⻆ᵯ濇孛⍵!
Tpoz!丳摤⒪␌孆Ɂ
㱌
ᶞ斖㫆⌵䒃㒩昀濇⫭堩㕚⍎偡ợ䒌斨彥䗨圞ᶁ!Ɂ
⣦ẹ㈪⋜⏰堩悱↱曆㛣!
⫭堩㚐㚞ᶯ↱濇孛€㈪⋜↱曆㛣Ɂ
.B!㈪⋜
㈪⋜↱曆㛣↱濇孛䟒⫾ⵖ㉭ᵯ(OFF)撒Ɂ
㉭ᵯ(OPEN)濇䂚⍲⭪↱曆㛣㸵↔⍗弝濇䂚⍲廟廟㈭
⅞↱曆㛣䗨ⵊ䩓Ɂ
.C!堩悱
⭪↱曆㛣䗨⪸! ⢻↔㚐堩仒䗨廘! ᵮ濇䂚⍲廟廟㌌
ⵊ䩓Ɂ
「䗨㯡廊㐲㰅㙭!BDD!ằ仒㕚
䗨嫊⎮
⃗救㐲⍲濇⼩柟㉭ẳ㚐㚞ᵮ䗨!
ᵱ㒢濇䙘兗㖢
䢞㳬⢕Ɂ
⎊ⅽ濇㖢䢞⮳⭪ᵤ䙘䚤Ḳ佰㳬佻䒙㯄Ɂ
SFTFU!㉭搒
⺷⫭堩⏰彂㌉⫰ㅴ濇⌺ᵯ↱曆㛣⍲濇∅孛䒌♪䍄䩸䪭
㉭⋯!SFTFU!㉭搒Ɂ
-
1
-
2
Sony MEX-1GP is an in-car audio system that combines the convenience of modern connectivity with a wide range of audio playback options, allowing you to enjoy your favorite music and enhance your driving experience. Equipped with a CD/MD changer, you can seamlessly switch between your favorite discs and immerse yourself in a rich and dynamic sound. The USB port enables effortless connection to external storage devices, granting you access to a diverse collection of digital music files.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sony MEX-BT5000 Installation guide
-
-
-
Sony CDX-GT50UI Installation guide
-
Sony Portable CD Player CDX-GT860U User manual
-
Sony MEX-1GP Installation guide
-
-
-
-