Garmin GMR™ 24 xHD Operating instructions

Brand: Garmin

Model: GMR™ 24 xHD

Type: Operating instructions

Marine Ethernet Installation

Instructions

The Garmin Marine Network is an Ethernet network used to

share data such as radar, sonar, and detailed mapping. You

can modify the Ethernet cable to suit your installation needs. To

obtain the best performance and to avoid damage to your boat,

install the connector according to these instructions. Read all

installation instructions before proceeding with the installation. If

you experience difficulty during the installation, contact Garmin

Product Support.

Contacting Garmin Product Support

• Go to www.garmin.com/support and click Contact Support

for in-country support information.

• In the USA, call (913) 397.8200 or (800) 800.1020.

• In the UK, call 0808 2380000.

• In Europe, call +44 (0) 870.8501241.

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

Preparing the Network Cable

Cleanly cut the Ethernet cable

to the needed length.

NOTE: Retain the connector for use in step 4.

Remove the strain-relief nut

from the cable-connection

housing

and slide the nut onto the cut end of the Ethernet

cable.

Feed the cut cable end through the connection housing.

Examine the connector removed from the cable and

compare it to this table to determine whether cable side A or

cable side B was removed.

Position Side A Side B

1 White/Orange White/Green

2 Orange Green

3 White/Green White/Orange

4 Blue Blue

5 White/Blue White/Blue

6 Green Orange

7 White/Brown White/Brown

8 Brown Brown

NOTE: As a point of reference, the brown wire will always be

in position 8.

NOTE: The Garmin Marine Network requires cross-over

cables not exceeding 100 m between devices.

Using a sharp knife, insert the blade between the cable

shield and jacket, and slit the jacket 16 mm (

in.) from the

cut end of the cable.

Peel the jacket back and remove the slit portion.

Trim the drain wire

to approximately 14 mm (

in.) and

fold the drain wire back over the jacket.

Arrange the individual wires in order according to table

shown in step 4.

NOTE: When constructing a custom cable from bulk wire,

you must create both a side A and a side B.

Trim the wires to an even length, leaving approximately

14 mm (

in.) from the ends of the wires to the jacket edge.

Wrap the supplied copper tape around the drain wire and

jacket.

Using a pair of pliers, squeeze the copper tape to pre-form

the cable jacket end.

Installing the Network Connector

With the wires in the correct order, insert the wires into the

modular plug until the ends of the wires touch the bottom of

the plug.

Verify the wires are in the correct order.

If any wire is not in the correct position, remove the plug,

arrange the wires in the correct order, and reinsert the wires

into the plug.

Using a modular plug hand tool, crimp the plug onto the

wires.

Align the release tab on the modular plug with the

corresponding notch in the cable-connection housing, and

push the cable through the connection housing until plug is

securely seated.

Screw the strain relief nut onto the cable-connection housing

and tighten with a 15 mm wrench.

NOTE: Do not overtighten the nut.

Install the O-ring onto the housing.

The cable is now ready for use.

April 2014

190-00489-00_0C Printed in Taiwan

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of Garmin.

www.garmin.com/support

Garmin GMR™ 24 xHD Operating instructions

Garmin GMR™ 24 xHD Operating instructions

Garmin GMR™ 24 xHD Operating instructions

Related papers

Other documents