JBSYSTEMS LP-8140 Owner's manual

Brand: JBSYSTEMS

Model: LP-8140

Category: Floodlights

Type: Owner's manual

This manual is also suitable for

LP-8115

Version: 1.0

WWW.BEGLEC.COM

Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.

LP-8115/

LP-8140

Operation Manual

Mode d'emploi

Gebruiksaanwijzing

Bedienungsanleitung

Manual de instrucciones

Manual do utilizador

EN - DISPOSAL OF THE DEVICE

Dispose of the unit and used batteries in an environment friendly manner

according to your country regulations.

FR - DÉCLASSER L’APPAREIL

Débarrassez-vous de l’appareil et des piles usagées de manière écologique

Conformément aux dispositions légales de votre pays.

NL - VERWIJDEREN VAN HET APPARAAT

Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke

manier conform de in uw land geldende voorschriften.

DU - ENTSORGUNG DES GERÄTS

Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und

Weise gemäß den Vorschriften Ihres Landes.

ES - DESHACERSE DEL APARATO

Reciclar el aparato y pilas usadas de forma ecologica conforme a las

disposiciones legales de su pais.

PT - COMO DESFAZER-SE DA UNIDADE

Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em

conformidade com as normas vigentes no seu país.

ENGLISH OPERATION MANUAL

JB SYSTEMS

1/20 LP-8115 & LP-8140 RGB LED PROJECTOR

Thank you for buying this JB Systems

product. To take full advantage of all possibilities and for your own safety, please

read these operatinginstructions verycarefully before you start using thisunit.

FEATURES

This unit is radio-interference suppressed. This product meets the requirements of the current European and national

guidelines. Conformity has been established and the relevant statements and documents have been deposited by the

manufacturer.

 This devicehas been designedto produce decorative effect lighting andis used in light showsystems.

 A lightweight RGB LED projector to be used withthe LED MANAGER (special DMX power supply)

 81 LEDS (Red26pcs + Green26pcs + Blue29pcs) behind asturdy 15cm x 15cm cover.

 Two beam angles available: 15° and40°

 Can be built inany wall and/or ceiling

 Hangingbracket included for easy fixing on truss or any surface

 Very easy electrical4-wire connection

 Lowpowerconsumption, only 10watts!

 No heat dissipation!

 Can be usedindiscotheques, pubs,lounges, buildings, parkings,homes, etc.

BEFORE USE

 Before you start using this unit, please check if there’s notransportation damage. Should there be any, do not use the

device and consult yourdealer first.

 Important: This device left our factory in perfect conditionand well packaged. It is absolutely necessary for the user to

strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not

subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by

disregardingthisuser manual.

 Keep this booklet in a safe place for future consultation. If yousell the fixture, be sure to add this user manual.

Check thecontents:

Check thatthe carton contains the followingitems:

 Operatinginstructions

 LP-8115 unit (beam angle = 15°) orLP-8140 unit (beam angle = 40°)

 Hangingbracket with2 knobs

 2 Springclips

SAFETY INSTRUCTIONS:

This symbolmeans: indoor use only.

This symbolmeans: Read instructions.

 To protect the environment, please try to recyclethe packingmaterial as much as possible.

 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it

into awarm room after transport. Condense sometimes prevents the unit from working at full performance ormay even

causedamages.

 This unitis for indoor use only.

 Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object

enters the unit,immediately disconnectthe mains power.

 Prevent use industy environments andclean the unit regularly.

 Keep the unitaway from children.

 Inexperienced persons shouldnot operatethis device.

 Maximum save ambient temperatureis 40°C. Don’t usethis unit at higher ambient temperatures.

 Make sure the area belowthe installation placeis free from unwanted persons during installation andservicing.

 The electrical installation should be carried out by qualified personal only, according to the regulations for electrical

and mechanical safety inyourcountry.

 Check thatthe available voltageis not higher thanthe one stated onthe rear panel ofthe unit.

 Don’t connect the unit to any dimmer pack.

 Please use the original packingwhen the device is to be transported.

 Due to safety reasons it is prohibited to make unauthorizedmodificationsto the unit.

ENGLISH OPERATION MANUAL

JB SYSTEMS

2/20 LP-8115 & LP-8140 RGB LED PROJECTOR

Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from

epilepsy.

INSTALLATION:

When you connect theLP-8115/LP-8140 to theLED MANAGER, just connect thecorresponding colors:

You can install the LP-8115 & LP-8140 in 3 ways:

1.Using the includedhanging bracket to fix the LP-8115/LP-8140 with a mounting hook

2.You can build the LP-8115/LP-8140 in amounting panel (ex. ceiling)

3.Installing theLP-8115/LP-8140 in amounting panel USING4 SCREWS:

1. Usingtheincludedhangingbracket:

The hanging bracket has 2 knobs and a mounting hole to fixa smallmountinghook.

Before installing this unit, please take note of following information:

 Make sure the area below the installation place is free from unwanted persons while

installing

 The device should be well fixed, free-swinging mounting is dangerous and may not be

considered!

2. Installing the LP-8115/LP-8140 in a mountingpanel USINGTHE SPRINGCLIPS:

IMPORTANT NOTE: Before you startinstalling the unit, be sure to remove the hanging bracket first !

Before installingthis unit, please take note of followinginformation:

 The diameter ofthe hole cutout has to be 125mm x 125mm

 The thickness of the mountingpanel (ceiling) can be up to 15mm

 Make sure the area below the installation place is free from unwanted

persons while installing

How toinstall the unit:

 Install the Spring Clips onboth sides ofthe enclosure.

 Make sure you make the electrical connections before you install the unit

in the mounting panel!

 Press both Spring Clips upwards (see pictureA).

 Slide the armature in the 125mm x 125mm hole of the mounting panel

(ceiling).

 Release theSpringClips (see picture B).

 The armature will belockedin the mounting panel (ceiling).

!! This LP-8115/LP-8140 can only be used together with the JB SYSTEMS

LED MANAGER !!

!!! DON’T CONNECT DIRECTLY TO 230Vac or any ordinary 24Vdc power supply !!!

ENGLISH OPERATION MANUAL

JB SYSTEMS

3/20 LP-8115 & LP-8140 RGB LED PROJECTOR

3. Installing the LP-8115/LP-8140in amounting panel USING 4 SCREWS:

You will have difficulties using the spring

clips when the mounting panel is thicker

than 15mm. In that case you can mount

the armature asfollows:

 Make a hole as shown on the

drawing. (you will have to widen the

hole at some locations with a file to fit

the armatureperfectly)

 Remove the safety screen (and the

Spring Clips when they are attached

to the unit)

 Drill 4 holes on the locations marked

bythe circles (seepicture C)

 Fix the unit in the mounting panel with

4 adapted screws

 Place thesafety screen back onthe fixture

OVERHEAD RIGGING



Important: The installation must be carried out by qualified service personal only. Improper

installation can result in serious injuries and/or damage to property. Overhead rigging requires extensive

experience! Working load limits should be respected, certified installation materials should be used, the

installed device should be inspectedregularly for safety.

 Make sure the area belowthe installationplaceis free from unwanted persons during rigging, de-rigging andservicing.

 Locate the fixturein a well ventilated spot, far away from any flammable materials and/or liquids.

 The device should beinstalled out of reach of people andoutside areas where persons may walk by orbe seated.

 The device should be well fixed; a free-swingingmounting isdangerous andmay not be considered!

 The operator has to make sure that the safety-relating andmachine-technical installations are approved by an expert

before using them for thefirst time. The installations should be inspected every year by a skilled person to be sure that

safety is still optimal.

MAINTENANCE

 Make surethe area below the installationplace is free from unwanted persons duringservicing.

Duringinspection thefollowing pointsshould bechecked:

 All screws used forinstalling the device and anyof its parts shouldbe tightly fastened andmay not be corroded.

 Housings, fixations andinstallations spots (ceiling,truss, suspensions) should betotally free from any deformation.

 The cables must be in impeccable condition and should be replaced immediately when even a small problem is

detected.

Attention: We strongly recommend internal cleaning to be carried outby qualifiedpersonnel!

SPECIFICATIONS

Input: 3x 24Vac comingfrom the LEDMANAGER

Powerconsumption: 10Watt

Lamp: LED: Red 26pcs Green26pcs Blue 29pcs

Beamangle: 15° (LP-8115) or 40° (LP-8140)

Size: 146 ×146 × 55mm

Weight: 0.3kg

LP-8115 LP-8140

Every information is subjectto change without prior notice

You can download the latestversion ofthisuser manualon our website: www.beglec.com

FRANÇAIS MODE D’EMPLOI

JB SYSTEMS

4/20 LP-8115 & LP-8140 RGB LED PROJECTOR

Merci d’avoir choisi ce produitJB Systems

. Pour votre sécurité et pourune utilisation optimale detoutes les possibilités

de l’appareil,lisez attentivement cettenotice avant utilisation.

EN VOUS INSCRIVANT POUR LA LETTRE D’INFORMATION VOUS SEREZ TOUJOURS TENU AU

COURANT DES DERNIERES NOUVELLES CONCERNANT NOS PRODUITS: NOUVEAUTES,

ACTIONS SPECIALES, JOURNEES PORTES OUVERTES, ETC.

 SURFEZ SUR: WWW.BEGLEC.COM 

CARACTERISTIQUES

Cet appareil ne produit pas d’interférences radio. Il répond aux exigences nationales et européennes. La conformité a

été établie et les déclarations et documents correspondants ont été déposés par le fabricant.

 Cet appareil a été conçupourla productionde jeux de lumières décoratifs et estutilisé dans des spectacles lumineux.

 Projecteur RGB à LED, très léger, à utiliser uniquement avec le LED MANAGER (appareil d'alimentation externe,

spécialement adapté auxnormes DMX).

 81 LED: 26 rouges + 26vertes + 29 bleues, placées derrière une solide vitre de protectionde 15 x 15 cm.

 Deuxangles de dispersion sont disponibles : 15° et 40°.

 L'appareil peut être encastré dans n'importe quel paroi et/ou plafond.

 Une équerre destinée à suspendre l'appareil est fournie pour le fixer aisément sur une barre de support ou sur

n'importe quelle surface.

 Connexion électrique très simple, à4 fils.

 Trèsbasse consommationde courant,seulement 10 watts !

 Pas de production de chaleur !

 L'appareilpeut être utilisédans des discothèques, des cafés, des salons, des bâtiments, des parkings, des habitations

diverses, etc …

AVANT UTILISATION

 Avant d’utiliser cet appareil, assurez-vous de l’absence de dommages liés au transport. En cas de dommages,

n’utilisez pasl’appareil etcontactezle vendeur.

 Important: Cet appareil a quitté notre usine en parfaite condition et bien emballé. Il est primordial que l’utilisateur

suive les instructions de sécurité et avertissements inclus dans ce manuel. La garantie ne s’applique pas en cas de

dommage lié à une utilisation incorrecte. Le vendeur ne prend pas la responsabilité des défauts ou de tout problème

résultant dufait de n’avoir pas tenu compte des mises en garde de ce manuel.

 Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l’appareil, assurez-vous d’y

joindre cemanuel également.

 Afin de protéger l’environnement, merci de recycler les emballages autant que possible.

Vérifiezlecontenu:

Vérifiez si l’emballage contient bienles articles suivants :

 Appareil LP-8115 (angle de dispersion =15°) ou LP-8140 (angle de dispersion =40°) ;

 Mode d'emploi ;

 Equerre desuspensionmuniede ses deux boutons

 2 Springclips.

INSTRUCTIONS DE SECURITE:

Ce symbole signifie: uniquement pour usage à l'intérieur.

Ce symbole signifie : Lire lemode d’emploi.

 Afin de protéger l’environnement, merci de recycler les emballages autant que possible.

 Afin d’éviter tout risque d’incendie ou de décharge électrique,ne pas exposer cet appareil à la pluie ouà l’humidité.

 Pour éviter la formation de condensation à l’intérieur de l’appareil, patientez quelques minutes pour laisser l’appareil

s’adapter à la température ambiante lorsqu’il arrive dans une pièce chauffée après le transport. La condensation

empêche l'appareil de fonctionnermanière optimale, et elle peutmêmecauser des dommages.

 Cet appareil est destiné à une utilisation àl’intérieuruniquement.

 Ne pas insérer d’objet métallique ou renverser de liquide dans l’appareil. Aucun objet contenant un liquide, tels que

des vases, ne peut être placé sur cet appareil. Cela risquerait de provoquer une décharge électrique ou un

Page is loading ...

JBSYSTEMS LP-8140 Owner's manual

Brand: JBSYSTEMS

Model: LP-8140

Category: Floodlights

Type: Owner's manual

This manual is also suitable for

LP-8115

Download PDF

report

in other languages

français: JBSYSTEMS LP-8140 Le manuel du propriétaire
español: JBSYSTEMS LP-8140 El manual del propietario
Deutsch: JBSYSTEMS LP-8140 Bedienungsanleitung
Nederlands: JBSYSTEMS LP-8140 de handleiding
português: JBSYSTEMS LP-8140 Manual do proprietário

JBSYSTEMS LP-8140 Owner's manual

This manual is also suitable for

JBSYSTEMS LP-8140 Owner's manual

in other languages

Related papers

Other documents