Apollo STORM VINYL STORAGE Assembly Instructions

Brand: Apollo

Model: STORM VINYL STORAGE

Type: Assembly Instructions

APOLLO STORM VINYL STORAGE ASSEMBLY INSTRUCTIONS

LIST OF COMPONENTS

A 4 X 8MM STEEL STUDS AND LOCKING NUTS

B 4 X LOCATING DISCS

C 4 X LOWER LEG CAPS

D 8MM STEEL SPIKES WITH LOCKING NUTS

E 1 X APOLLO BADGE

F 1 X OAK SHELF WITH (REMOVABLE) REAR OAK STOP BAR

G 2 X LEG RODS

H 4 X LEG BOLTS

I 4 X LOCATING DISCS

J 4 X LEG TUBES

k 1 X TOP OAK SHELF

L 4 X LOCATING DISCS

Lower module assembly

FIT LOCKING NUTS TO SPIKES (D), SCREW

SPIKES INTO THE LOWER LEG CAP (C) COPPER

THREAD .

TAKING THE STEEL STUDS (A) AND LOCKING

NUTS, FIT THE LOCKING NUTS APPROX.

10MM UP THE THREAD. SCREW THE STUD

INTO THE BACK OF THE LOWER LEG CAP

WITH THE LOCKING NUT FACING THE CAP.

10MM

GAP

TAKE ONE OF THE LOCATING DISCS MAKING

SURE THE INNER RAISED PART IS FACING

AWAY FROM THE LEG CAP AND SLIDE

DOWN THE STUD UNTIL IT LOCATES INTO

THE LEG CAP. REPEAT FOR ALL 4 LEGS.

TAKE THE LEG TUBES (J) AND FIT LACATING

DISCS (I, L) INTO BOTH ENDS OF EACH TUBE

WITH THE INNER RAISED PART FACING

AWAY FROM THE TUBE.

SLOT THE LEG RODS (G) INTO THE LOCATING HOLE IN THE

SIE OF THE LEG TUBES.

TAKING THE OAK SHELF WITH REAR STOP BAR (F), LINE UP

THE “H” SHAPPED LEGS (WITH THE CROSSBAR HAVING THE

BIGGER GAP TOWARDS THE SHELF) ON THE SIDE WITH THE

STOP BAR FACING TOWARDS THE LEGS.

PLACE THE ASSEMBLED LOWER LEGS STUD THROUGH THE

SHELF AND SCREW INTO THE LEG TUBES. REPEAT THE

PROCESS WITH ALL 4 LOWER LEGS.

LINE UP THE TOP OAK SHELF (K) TO THE LEG

TUBES, ONCE IN POSITION SCREW IN THE LEG

BOLTS (H) WITH TH HEX KEY SUPPLIED.

FIT BADGE.

THESE INSTRUCTIONS ASSUME YOU WILL BE USING THE MODULE FOR 12” VINYL STORAGE. THIS

MODULE CAN BE ADAPTED TO STORE HIFI COMPONENTS IF REQUIRED. THE REAR OAK STOP BAR CAN

EASILY BE REMOVED BY REMOVINGTHE RETAINING SCREWS LOCATED UNDERNEATH THE LOWER

SHELF. THE LEG RODS (G) CAN ALSO BE DESCARDED IF PREFERED.

UP TO 4 ADDITIONAL APOLLO STORM 6 SHELF MODULES CAN BE STACKED ON TOP OF THE VINYL

STORAGE MODULE IF REQUIRED.

ONE SET OF 4 ATACAMA/APOLLO HD-L SPIKE SHOES ARE RECOMMENDED SHOULD THE MODULE BE

POSITIONED ON A DELICATE FLOOR COVERING TO PROTECT THE SURFACE FROM THE ISOLATION

SPIKES.

Please Note:- Oak is a natural material, so block colour variaon, knots and grain texture

is part of the intrinsic beauty of this hi support. Every module is aesthecally unique

and will darken over me as part of the woods ageing process, especially if exposed to

sunlight. This dierence will be enhanced should you add new extra shelving at a later

date, so where possible purchase your Apollo Storm as a complete matched set taking

into account your future storage requirements.

210618

WE OPERATE A POLICY OF CONTINUOUS IMPROVEMENT AND RESERVE THE RIGHT TO AMEND DESIGNS AND SPECIFICATIONS WITHOUT PRIOR NOTICE.

Apollo STORM VINYL STORAGE Assembly Instructions

Apollo STORM VINYL STORAGE Assembly Instructions

Apollo STORM VINYL STORAGE Assembly Instructions

Related papers

Other documents