Wonderfire 961 Installation and Owner's Manual

Brand: Wonderfire

Model: 961

Type: Installation and Owner's Manual

Model 961

Inset live fuel effect gas fire

Incorporating the Wonderfire Premier Control.

Fitted with one of the following fascia:

Bauhaus, Bloomsbury or

Ebony.

(G.C. Number 32-032-88)

INSTALLER: Please leave this guide with the owner

INSTALLATION AND OWNER GUIDE

We trust that this guide gives

sufficient details to enable this

appliance to be installed and

maintained satisfactorily. However, if

further information is required, our

Wonderfire Premier Technical

Helpline will be pleased to help.

Telephone 0844 8711 554 (National

call rates apply in the United

Kingdom).

In the Republic of Ireland

Telephone 0044 844 8711 554.

5137994/01

(including photocopying), stored in any medium by electronic means (including in any

retrieval system or database) or transmitted, in any form or by any means, whether

electronic, mechanical, recording or otherwise, without the prior written permission of

the copyright owner.

Applications for the copyright owner's permission to reproduce any part of this

publication should be made, giving details of the proposed use, to the following

address: The Company Secretary, Baxi Heating UK Limited, The Wyvern Business

Park, Stanier Way, Derby, DE21 6BF.

Warning: Any person who does any unauthorised act in relation to a copyright work

may be liable to criminal prosecution and civil claims for damages.

Wonderfire Premier, Wood Lane, Erdington, Birmingham B24 9QP

www.wonderfire.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from

those given in this publication

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

UNDER NO CIRCUMSTANCES IS THIS FIRE TO BE CONVERTED TO LPG.

AN LPG KIT DOES NOT EXIST FOR THIS GAS FIRE.

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Page 2

Safety First.

Wonderfire Premier fires are CE Approved and designed to meet the appropriate

British Standards and Safety Marks.

Quality and Excellence.

All Wonderfire Premier fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted

by the British Standards Institute.

The Highest Standards

Wonderfire is a member of SBGI and HHIC (Heating and Hot water Industry Council)

that work to ensure high standards of safety, quality and performance.

Careful Installation

This gas fire must be installed by a competent GAS SAFE REGISTER engineer (GAS

SAFE REGISTER or CORGI engineer outside of UK) in accordance with our installer

guide and should not be fitted directly on to a carpet or floor of combustible material.

Page 3

INSTALLER GUIDE

Page 4

INSTALLER GUIDE

FOR OWNER GUIDE SEE PAGES 48 TO 67

INSTALLER GUIDE

Page 5

CONTENTS

Section Heading Page

INSTALLER GUIDE 4 - 47

OWNER GUIDE 48 - 67

1. IMAGES 7

2. SAFETY AND UNPACKING 8

3. APPLIANCE DATA, EFFICIENCY AND NOx 9

3.1 General information. 9

3.2 Efficiency. 10

3.3 NOx 10

4. GENERAL INSTALLATION REQUIREMENTS 11

4.1 Regulations, Standards and Law. 11

4.2 Ventilation requirements. 12

4.3 The Atmosphere sensing device (ASD). 12

4.4 Fireguard requirements. 12

4.5 Room considerations. 12

4.6 Chimney preparation. 12

4.7 Fireplace preparation. 13

4.8 The hearth and surround. 13

4.9 Fireplace clearances. 14

4.10 Installation options. 16

4.11 Flues. 19

5. PACK CONTENTS 20

6. FIREPLACE CHECK 23

7. IGNITION CHECK 24

8. GAS SUPPLY CONNECTION 24

9. PREPARING APPLIANCE FOR INSTALLATION 25

10. CONVECTION BOX INSTALLATION 27

10.1 Method 1 - Front fixing to fireplace surround. 27

10.2 Method 2 - Cable retention and floor fixing. 28

10.3 Sealing floor front - All installations. 30

11. BURNER AND SUPPLY PIPE INSTALLATION 31

11.1 Burner and supply pipe installation. 31

11.2 Preliminary burner checks. 31

11.3 Inlet pressure check. 32

Continued on next page

INSTALLER GUIDE

Page 6

CONTENTS (Continued)

Section Heading Page

12. FITTING THE CERAMIC FUEL EFFECT 32

13. FITTING THE WINDOW FRAME ASSEMBLY 33

14. OPERATING AND SPILLAGE CHECKS 33

14.1 Fitting the control knob extension on the Bloomsbury model. 33

14.2 Checking the control settings. 33

14.3 Check for spillage. 34

14.4 Flame supervision and spillage monitoring system. 35

15. OUTLET BAFFLE AND FASCIA FITTING 36

15.1 Fitting the outlet baffle. 36

15.2 Fitting the fascia. 36

15.3 Fitting the firefront casting / lower firefront casting. 37

16. FINAL REVIEW 38

17. SERVICING & PARTS REPLACEMENT 39

17.1 Checking the aeration setting of the burner. 40

17.2 To remove the ignition microswitch. 40

17.3 To remove the gas shut-off microswitch. 40

17.4 To remove the fascia. 41

17.5 To replace the control slide unit. 42

17.6 To replace the control slide button. 42

17.7 To remove and fit the window mounting frame and window assembly. 43

17.8 To remove the window assembly. 43

17.9 To remove the fuel effect. 44

17.10 To remove the ceramic side walls. 44

17.11 To remove the electronic ignition generator. 44

17.12 To remove the complete burner unit. 45

17.13 To remove the thermocouple interrupter block (See figure 36). 45

17.14 To remove the pilot unit. 45

17.15 To remove the shut-off tap. 45

17.16 To remove the gas flow rate controller. 46

17.17 To replace the burner. 47

17.18 To remove the main burner injector. 47

17.19 To remove the appliance from the fireplace. 47

INSTALLER GUIDE

Page 7

1. IMAGES

Ebony fascia

Bauhaus fascia

Bloomsbury fascia

2. SAFETY AND UNPACKING

Installer

Before continuing any further with the installation of this appliance please read the

following guide to manual handling.

 The approximate lifting weight (kg) of this appliance is as below:

Model

Heat Engine Firefront Combined Weight

Bauhaus 8.64 12.00 20.64

Bloomsbury 8.64 7.22 15.86

Ebony 8.64 9.13 17.77

One person should be sufficient to lift the fire. If for any reason this weight is

considered too heavy then obtain assistance.

 When lifting always keep your back straight. Bend your legs and not your back.

 Avoid twisting at the waist. It is better to reposition your feet.

 Avoid upper body/top heavy bending. Do not lean forward or sideways whilst

handling the fire.

 Always grip with the palm of the hand. Do not use the tips of fingers for support.

 Always keep the fire as close to the body as possible. This will minimise the

cantilever action.

 Use gloves to provide additional grip.

 Always use assistance if required.

This product uses fuel effect pieces and burner compartment walls containing

Refractory Ceramic Fibres (RCF), which are man-made vitreous silicate fibres.

Excessive exposure to these materials may cause irritation to eyes, skin and

respiratory tract. Consequently, it is important to take care when handling these

articles to ensure that the release of dust is kept to a minimum. To ensure that

the release of fibres from these RCF articles is kept to a minimum, during

installation and servicing we recommend that you use a HEPA filtered vacuum

to remove any dust and soot accumulated in and around the fire before and

after working on the fire. When replacing these articles we recommend that the

replaced items are not broken up, but are sealed within a heavy duty polythene

bag, clearly labelled as RCF waste. RCF waste is classed as a stable, non-

reactive hazardous waste and may be disposed at a landfill licensed to accept

such waste. Protective clothing is not required when handling these articles,

but we recommend you follow the normal hygiene rules of not smoking, eating

or drinking in the work area and always wash your hands before eating or

drinking.

This appliance does not contain any component manufactured from asbestos or

asbestos related products.

INSTALLER GUIDE

Page 8

INSTALLER GUIDE

Page 9

3. APPLIANCE DATA, EFFICIENCY AND NO

3.1 General information.

Under no circumstances is this fire to be converted to LPG. An LPG conversion kit

does not exist for this gas fire.

The appliance information label is located on a chained plate at the base of the fire.

This can be seen by removing fire front / fire front casting.

Gas Natural (G20)

Inlet Pressure 20mbar

Input - Max. (Gross) 5.00kW (17,060 Btu/h)

Input - Min. (Gross) 2.5kW (8,530 Btu/h)

Input - Max. (Net) 4.5kW (15,371 Btu/h)

Input - Min. (Net) 2.25kW (7,677 Btu/h)

Inlet Test Pressure (Cold) 20.0 ± 1.0mbar (8.0 ± 0.4in w.g.)

Gas Connection 8mm pipe

Burner Injector Cat 82 - 065

Pilot & Atmosphere Sensing Device Copreci Ref. O.D.S 21500/166

Ignition Electronic (Alkaline Battery 9V PP3)

Aeration Setting Factory set - See section 17.1

Figure 1.

INSTALLER GUIDE

Page 10

3.2 Efficiency.

The efficiency of this appliance has been measured as specified in BS 7977 - 1 and

the result is as below:

Model Efficiency % (Gross) Efficiency % (Net)

961 80 89

The gross calorific value of the fuel has been used for this efficiency calculation. The

test data from which it has been calculated has been certified by Advantica

Certification services (0087). The efficiency value may be used in the UK

Government's Standard Assessment Procedure (SAP) for energy rating of dwellings.

The conversion of net efficiency to gross was achieved by multiplying the net

efficiency by the following conversion factor from Table E3 of SAP 2005, rounding

down to the nearest whole number.

3.3 NO

The 'Weighted' result for this appliance equates to NO

Class II.

Gas Conversion factor from net to gross efficiency

Natural Gas 0.901

INSTALLER GUIDE

Page 11

4. GENERAL INSTALLATION REQUIREMENTS

4.1 Regulations, Standards and Law.

The installation must be in accordance with these instructions.

For the user’s protection, in the United Kingdom it is the law that all gas appliances

are installed by competent persons in accordance with the current edition of the Gas

Safety (Installation and Use) Regulations. Failure to install the appliance correctly

could lead to prosecution. GAS SAFE REGISTER and CORGI require their members

to work to recognised standards.

In the United Kingdom the installation must also be in accordance with:

All the relevant parts of local regulations.

All relevant codes of practice.

The relevant parts of the current editions of the following British Standards:-

BS EN 1856 Part 1 - Chimneys - Requirements for metal chimneys.

BS 715 - Specification for metal flue boxes for gas-fired appliances not

exceeding 20kW.

BS EN 1858 - Chimneys - Components - Concrete flue blocks.

BS EN 1806 - Chimneys - Clay / ceramic flue blocks.

BS 5440 Part 1 - Installation of flues.

BS 5440 Part 2 - Installation and maintenance of flues and ventilation for gas

appliances of rated input not exceeding 70 kW net (1st, 2nd

and 3rd family gases).

BS 6461 Part 1 - Masonry chimney & flues - Installation

BS 1251 - Fireplace components

BS 5871 Part 2 - Installation - Inset LFE gas fires

BS 6891 - Gas pipework installation

 In England and Wales, the current edition of the Building Regulations issued by the

Department of the Environment and the Welsh Office.

 In Scotland, the current edition of the Building Standards (Scotland) Regulations

issued by the Scottish Executive.

 In Northern Ireland, the current edition of the Building regulations (Northern Ireland)

issued by the Department of the Environment for Northern Ireland.

 In the republic of Ireland the installation must be carried out by a competent person

and also conform to the relevant parts of:

a) The current edition of IS 813 “Domestic Gas Installations”.

b) All relevant national and local rules in force.

Where no specific instructions are given, reference should be made to the relevant

British Standard Code of Practice.

INSTALLER GUIDE

Page 12

4.2 Ventilation requirements.

Normal adventitious ventilation is usually sufficient to satisfy the ventilation

requirements of this appliance. In GB reference should be made to BS 5871 Part 2

and in IE reference should be made to the current edition of IS 813 “Domestic Gas

Installations” which makes clear the conditions that must be met to demonstrate that

sufficient ventilation is available.

4.3 The Atmosphere sensing device (ASD).

The appliance is fitted with an A.S.D (Atmosphere sensing device). If the appliance

closes down after a period of operation for no apparent reason, the consumer should

be informed to stop using the appliance until the installation and appliance have been

thoroughly checked. The A.S.D will shut the appliance down if an unacceptable

amount of harmful products of combustion accumulate. Under no circumstances

should the A.S.D be altered or bypassed in any way. Only a genuine manufacturer’s

replacement part should be fitted. The individual A.S.D components are not

replaceable.

4.4 Fireguard requirements.

A fireguard complying with BS 8423 should be fitted for the protection of young

children, the elderly, the infirm and pet animals.

4.5 Room considerations.

4.5.1 This appliance must not be installed in any room that contains a bath or shower

or where steam is regularly present.

4.5.2 An extractor fan may only be used in the same room as this appliance, or in any

area from which ventilation for the appliance is taken, if it does not affect the safe

performance of the appliance. Note the spillage test requirements detailed further on

in this guide. If the fan is likely to affect the appliance, the appliance must not be

installed unless the fan is permanently disconnected.

4.5.3 Note that soft wall coverings (e.g. embossed vinyl, etc.) are easily affected by

heat. They may scorch or become discoloured when close to a heating appliance.

Please bear this in mind when installing.

4.6 Chimney preparation.

4.6.1 If the appliance is intended to be installed to a chimney that was previously used

for solid fuel, the flue must be swept clean prior to installation. All flues should be

inspected for soundness and freedom from blockages.

4.6.2 Any chimney damper or restrictor should be removed. If removal is not possible,

they must be secured in the open position.

INSTALLER GUIDE

Page 13

4.7 Fireplace preparation.

4.7.1 If the fireplace opening is an underfloor draught type, it must be sealed to stop

any draughts.

4.7.2 The fireplace floor should be reasonably flat to ensure that the convection box

can be installed without it rocking and so that a good seal can be made at the bottom

front of the box.

4.7.3 The front face of the fireplace should be reasonably flat over the area covered

by the convection box top and side flange seals to ensure good sealing. These faces

should be made good if necessary. The fireplace floor should be reasonably flat to

ensure that a good seal with the convection box can be made.

4.7.4 If the appliance is to be fitted against a wall

with combustible cladding, the cladding must be

removed from the area covered by the fascia. The

cladding must also not touch the fascia (See figure

2). We suggest that the actual fascia is used as a

template to mark the area for combustible cladding

removal and that this area is increased by at least

2mm all round.

4.7.5 If the fireplace opening is greater than the

acceptable dimensions given in this guide, do not

use the back of a fire surround or marble to reduce

the opening. This may cause cracking of the

surround back or marble.

4.8 The hearth and surround.

The appliance must be mounted behind a non-combustible hearth unless the

conditions of section 4.10.1.1 are met (N.B. conglomerate marble hearths are

considered as non-combustible). The appliance can be fitted to a purpose made

proprietary class “O”-150°C surround. The hearth material must be at least 12mm

thick. The periphery of the hearth (or fender) should be at least 50mm above floor

level to discourage the placing of carpets or rugs over it.

The surface of the hearth must be sufficiently flat to enable the bottom of the front

surround and the bottom front cover to be aligned horizontally. Any excessive

unevenness (uneven tiles, Cotswold stone, etc.) should be rectified.

The appliance must not stand on combustible materials or carpets.

Figure 2. Removal of combustible

cladding (Fascia may differ from

that shown).

INSTALLER GUIDE

Page 14

4.9 Fireplace clearances.

4.9.1 The minimum height from the base of the fireplace opening to the underside of

any shelf made from wood or other combustible materials is detailed below.

For Bauhaus and Ebony models:-

• For a shelf up to 150mm deep: Minimum height = 700mm.

• For a shelf deeper than 150mm: 700mm + 12.5mm for every 25mm depth over

150mm (See Figure 3).

For Bloomsbury models:-

• For a shelf up to 150mm deep: Minimum height = 775mm.

• For a shelf deeper than 150mm: 775mm + 12.5mm for every 25mm depth over

150mm (See Figure 4).

Figure 3. Combustible shelf clearances

Figure 4. Combustible shelf clearances

INSTALLER GUIDE

Page 15

4.9.2 The minimum allowable distance from the outside of the appliance fascia to a

corner wall having combustible material or any other combustible surface which

projects beyond the front of the appliance is shown in figure 5. A 10mm access

clearance from a non-combustible surface is necessary at the left side.

Figure 5. Appliance dimensions and clearances (The fascia may differ from that

shown and dimensions are subject to manufacturing tolerances)

Key Description

Model

Bauhaus Bloomsbury Ebony

A Height (mm) 616 741 616

B Width (mm) 518 588 518

C Depth into room (mm) 117 127 126

Minimum mandatory clearance to

combustible surfaces projecting beyond

the front of appliance (mm).

100 100 100

Recommended clearance to non-

combustible surfaces for access purposes

(mm).

50 50 50

INSTALLER GUIDE

Page 16

4.10 Installation options.

In the United Kingdom, as supplied, the appliance can be installed in the following

situations: -

4.10.1 Conventional fireplace and hearth.

To a fireplace complete with surround and hearth as shown in figure 6 and complying

with BS1251 after removal of the fireback and sufficient material behind the fireback

for a debris catchment space. The required fireplace, hearth, debris catchment area

and clearance dimensions are shown in figure 7.

Figure 7. Fireplace area.

Figure 6. Hearth and fireplace opening dimensions

INSTALLER GUIDE

Page 17

4.10.1.1 ‘Hole-in-the-wall’ Installations.

 It is recommended that a hearth should be installed as in section 4.8.

 If a reduced depth hearth is fitted, the fire must be installed so that the distance

from the base of the fireplace opening in the wall to the finished floor level is at

least 100mm. It is recommended that the reduced hearth has a depth from the

fixing plane of the fire of 100mm minimum. This is necessary to support the lower

front casting. Where there is no floor covering or carpet and the floor is of a type

that is likely to be covered in such a way in the future then the distance from the

base of the fireplace opening in the wall to the floor level should be increased to at

least 175mm.

4.10.2 Metal flue box and hearth.

The appliance can be installed to a fireplace incorporating a metal flue box complying

with the constructional requirements of the current edition of BS 715 and with a flue

conforming to BS EN 1856 part 1. The dimensions of the flue box must conform to

those shown in figure 8.

The top, sides and rear surface of the metal flue box must be covered with a 50mm

layer of mineral wool or equivalent insulation (See figure 8).

Important Note: Where the flue box has a base sheet that is single wall (i.e. a single

metal sheet) the flue box must be mounted on a non-combustible hearth. The hearth

material must be at least 12mm thick.

Figure 8. Metal flue box dimensions

INSTALLER GUIDE

Page 18

4.10.3 Precast concrete or clay flue block system and hearth.

The appliance can be installed to a precast concrete or clay flue block system

conforming to BS EN 1858 with dimensions as in figure 9.

BS 1289 part 1 recommends there should be an air space or insulation between the

flue blocks and the plaster because heat transfer may cause cracking on directly

plastered flues. However, generally this appliance is suitable for installations under all

circumstances unless there is a history of cracking problems.

Remember that faults such as cracking may be caused by poorly built and restrictive

flues, e.g. mortar extrusions, too many bends, flue heights below three metres,

restrictive terminations etc.

Figure 9. Precast or clay flue block system

INSTALLER GUIDE

Page 19

4.11 Flues.

1. Suitable flues and minimum flue sizes are as follows:

It should be noted that, as with many appliances, sharp bends or horizontal runs in

metal flues at the top of the system can be a cause of problems in these types of

installation.



225mm x 225mm conventional brick flue.



175mm diameter lined brick or stone flue.



200mm diameter factory made insulated flue manufactured to BS4543 Part 2.



175mm diameter flue pipe. See BS6461 Part 1 for suitable materials.



Single wall, twin wall or flexible flue liner with a minimum diameter of 125mm. The

materials to be used are stainless steel or aluminium as specified in

BS EN 1856 Part 1. The liner must be sealed to the surrounding area above the

fireplace opening and to the top of the chimney. An approved terminal must be fitted.



A properly constructed precast concrete or clay flue system conforming to BS1289

or BS EN 1858. This system is only suitable if the conditions stated in section 4.10.3

are met.

2. The flue must conform to BS 5440: Part 1 in design and installation.

The flue, measured from the bottom of the fireplace opening to the bottom of the

terminal, shall be not less than 3m in actual vertical height. When calculated in

accordance with BS 5440: Part 1 Annex A, the minimum equivalent height of the flue

shall be 2.0m of 125mm dia. flue pipe.

3. The flue must not be used for any other appliance or application.

4. Proprietary terminals must comply with BS 715 or BS 1289. Any terminal or

termination must be positioned in accordance with BS 5440 Part 1 to ensure that the

products of combustion can be safely dispersed into the outside atmosphere. Where

the appliance is connected to an unlined brick chimney it is generally unnecessary for

the chimney pot to be replaced or for a terminal to be fitted unless the flue has a

diameter smaller than 170mm.

INSTALLER GUIDE

Page 20

5. PACK CONTENTS

1 Burner and convection box unit.

1 Burner tray trim.

1 Outlet baffle for the convected air outlet.

2 Tapping Screws for outlet baffle.

1 Nut and olive for 8mm inlet pipe.

1 ‘T’ connector and pressure test point.

1 Flue restrictor.

3 Tapping Screws (For flue restrictor).

2 Small “U” seals (For convection box side flanges).

2 Strips of floor sealing tape.

6 Fibre / wooden plugs.

4 Woodscrews.

2 Fire retaining cables.

2 Cable clamps.

4 Eyebolts.

1 Rubber grommet (For rear of convector box).

2 Machine screws (For fascia hanging).

2 Washers for fascia hanging.

1 PP3 Alkaline battery.

1 Smoke match tube.

2 Fireback spacing brackets.

4 Tapping Screws (For fireback spacing brackets).

1 Length of self adhesive foam seal.

1 Literature pack (Not shown).

1 Ceramic fuel effect set (Not shown).

1 Slider control position label.

1 Control knob extension bracket (Bloomsbury only)

2 M4 x 7mm screws for securing the control knob extension

bracket (Bloomsbury only).

1 Fascia and firefront casting.

1 Fascia Hood (Bauhaus and Ebony only).

4 Screws for fascia hood (Bauhaus and Ebony only).

Carefully remove all the contents. Take special care in handling the ceramic pieces.

Take care not to bend or distort the slide control linkage.

Check that all the listed parts are present and in good condition.

Page is loading ...

Wonderfire 961 Installation and Owner's Manual

Wonderfire 961 Installation and Owner's Manual

Wonderfire 961 Installation and Owner's Manual

Related papers

Other documents