Neff T48PD23X0 Operating instructions

Category
Hobs
Type
Operating instructions
[en] INSTRUCTION MANUAL
T48.D2...
Hob
2 Ø = cm
: :
: :
: :
,(&
: :
:



en
3
Table of contents
[en]INSTRUCTION MANUAL
8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
( Important safety information . . . . . . . . . . . . . . . 5
] Causes of damage . . . . . . . . . . . . . . . . . . . . . . . . 6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7 Environmental protection . . . . . . . . . . . . . . . . . . 7
Energy-saving advice . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Environmentally-friendly disposal . . . . . . . . . . . . . . . . . 7
f Induction cooking . . . . . . . . . . . . . . . . . . . . . . . . 7
Advantages of induction cooking. . . . . . . . . . . . . . . . . 7
Cookware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
* Getting to know your appliance . . . . . . . . . . . . . 9
The control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
The hotplates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Residual heat indicator. . . . . . . . . . . . . . . . . . . . . . . . 10
1 Operating the appliance . . . . . . . . . . . . . . . . . . 10
Switching the hob on and off . . . . . . . . . . . . . . . . . . . 10
Setting a hotplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chef's recommendations . . . . . . . . . . . . . . . . . . . . . . 11
w CombiZone function . . . . . . . . . . . . . . . . . . . . . 13
Notes regarding cookware. . . . . . . . . . . . . . . . . . . . . 13
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
u Move function. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Advice on using cookware. . . . . . . . . . . . . . . . . . . . . 13
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
O Time-setting options . . . . . . . . . . . . . . . . . . . . . 14
Programming the cooking time . . . . . . . . . . . . . . . . . 14
The kitchen timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
v PowerBoost function . . . . . . . . . . . . . . . . . . . . . 15
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
z Keep warm function. . . . . . . . . . . . . . . . . . . . . . 16
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
A Childproof lock. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Activating and deactivating the childproof lock . . . . . 16
Childproof lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
k Wipe protection . . . . . . . . . . . . . . . . . . . . . . . . . 17
b Automatic safety cut-out . . . . . . . . . . . . . . . . . . 17
Q Basic settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
To access the basic settings: . . . . . . . . . . . . . . . . . . .19
[ Energy consumption indicator . . . . . . . . . . . . . 19
t Cookware check. . . . . . . . . . . . . . . . . . . . . . . . . 20
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Hob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Hob surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
{ Frequently Asked Questions (FAQ) . . . . . . . . . 21
3 Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . 22
4 Customer service . . . . . . . . . . . . . . . . . . . . . . . . 23
E number and FD number . . . . . . . . . . . . . . . . . . . . .23
E Test dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.neff-international.com and in the online shop
www.neff-eshop.com
en Intended use
4
8Intended use
Intended use
Read these instructions carefully. Please keep
the instruction and installation manual, as well
as the appliance certificate, in a safe place for
later use or for subsequent owners.
Check the appliance after removing it from the
packaging. If it has suffered any damage in
transport, do not connect the appliance,
contact the Technical Assistance Service and
provide written notification of the damage
caused, otherwise you will lose your right to
any type of compensation.
This appliance must be installed according to
the installation instructions included.
This appliance is intended for private domestic
use and the household environment only. The
appliance must only be used for the
preparation of food and beverages. The
cooking process must be supervised. A short
cooking process must be supervised without
interruption. Only use the appliance in
enclosed spaces.
This appliance is intended for use up to a
maximum height of 4000 metres above sea
level.
Do not use covers. These can cause
accidents, due to overheating, catching fire or
materials shattering, for example.
Do not use inappropriate child safety shields
or hob guards. These can cause accidents.
This appliance is not intended for operation
with an external clock timer or a remote
control.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with, on, or around the
appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8 years old and are
being supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
We advise that you exercise caution using or
standing near an induction hob while it is in
operation, if you wear a pacemaker or a
similar medical device. Consult your doctor or
the device manufacturer concenring its
conformity or any possible incompatibilities,
Important safety information en
5
(Important safety
information
Important safety information
:Warning – Risk of fire!
Hot oil and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk of fire!
The hotplates become very hot. Never
place combustible items on the hob. Never
place objects on the hob.
Risk of fire!
The appliance gets hot. Do not keep
combustible objects or aerosol cans in
drawers directly underneath the hob.
Risk of fire!
The hob switches off automatically and can
no longer be operated. It may switch on
unintentionally at a later point. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
:Warning – Risk of burns!
The hotplates and surrounding area
(particularly the hob surround, if fitted)
become very hot. Never touch the hot
surfaces. Keep children at a safe distance.
Risk of burns!
The hotplate heats up but the display does
not work. Switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
Risk of burns!
Metal objects on the hob quickly become
very hot. Never place metal objects (such
as knives, forks, spoons and lids) on the
hob.
Risk of fire!!
After each use, always turn off the hob at
the main switch. Do not wait until the hob
turns off automatically after the pan is
removed.
:Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the after-
sales service.
Risk of electric shock!
Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk of electric shock!
A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk of electric shock!
Cracks or fractures in the glass ceramic
may cause electric shocks. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
:Warning – Malfunction risk!
The hob is equipped with a fan in the lower
section. If there is a drawer under the hob it
should not be used to store small objects or
paper, since they could damage the fan or
interfere with the cooling if they are sucked
into it.
There should be a minimum of 2 cm between
the contents of the drawer and fan intake.
:Warning – Risk of injury!
When cooking in a bain marie, the hob and
cooking container could shatter due to
overheating. The cooking container in the
bain marie must not directly touch the
bottom of the water-filled pot. Only use heat-
resistant cookware.
Risk of injury!
Saucepans may suddenly jump due to
liquid between the pan base and the
hotplate. Always keep the hotplate and
saucepan bases dry.
en Causes of damage
6
]Causes of damage
Causes of damage
Caution!
Rough pan bases may scratch the hob.
Avoid leaving empty pots and pans on the hotplate.
Doing so may cause damage.
Do not place hot pans on the control panel, the
indicator area, or the hob frame. Doing so may
cause damage.
Hard or pointed objects dropped on the hob may
damage it.
Aluminium foil and plastic containers will melt if
placed on the hotplate while it is hot. The use of
laminated sheeting is not recommended on the hob.
Overview
You will find the most frequently caused damage in the
following table:
Damage Cause Measure
Stains Boiled over food. Remove boiled over food immediately with a glass scraper.
Unsuitable cleaning agent. Only use cleaning agents that are suitable for this type of hob.
Scratches Salt, sugar and sand. Do not use the hob as a work surface or storage space.
Cookware with rough bases scratch the hob. Check the cookware.
Discolouration Unsuitable cleaning agent. Only use cleaning agents that are suitable for this type of hob.
Pan abrasion. Lift pots and pans when moving them.
Chips Sugar, food with a high sugar content. Remove boiled over food immediately with a glass scraper.
Environmental protection en
7
7Environmental protection
Environmental protection
In this section, you can find information about saving
energy and disposing of the appliance.
Energy-saving advice
Always use the correct lid for each pan. Cooking
without a lid uses a lot more energy. Use a glass lid
to provide visibility and avoid having to lift the lid.
Use pans with flat bases. Bases that are not flat use
a lot more energy.
The diameter of the pan base must match the size of
the hotplate. Please note: pan manufacturers usually
provide the diameter for the top of the pan, which is
usually larger than the diameter of the pan base.
Use a small pan for small amounts of food. A large
pan which is not full uses a lot of energy.
Use little water when cooking. This saves energy and
preserves all the vitamins and minerals in
vegetables.
Select the lowest power level to maintain cooking. If
the power level is too high, energy is wasted.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
fInduction cooking
Induction cooking
Advantages of induction cooking
Induction cooking is very different from traditional
cooking methods, as heat builds up directly in the item
of cookware. This offers numerous advantages:
Saves time when boiling and frying.
Saves energy.
Easier to care for and clean. Spilled food does not
burn on as quickly.
Heat control and safety – the hob increases or
decreases the heat supply as soon as the user
changes the setting. The induction hotplate stops the
heat supply as soon as the cookware is removed
from the hotplate, without having to switch it off first.
Cookware
Only use ferromagnetic cookware for induction cooking,
such as:
Cookware made from enamelled steel
Cookware made from cast iron
Special induction-compatible cookware made from
stainless steel.
To check whether your cookware is suitable for
induction cooking, refer to the section on
~ "Cookware check".
To achieve a good cooking result, the ferromagnetic
area on the base of the pan should match the size of
the hotplate. If a hotplate does not detect an item of
cookware, try placing it on another hotplate with a
smaller diameter.
Some induction cookware does not have a fully
ferromagnetic base:
If the base of the cookware is only partially
ferromagnetic, only the area that is ferromagnetic will
heat up. This may mean that heat will not be
distributed evenly. The non-ferromagnetic area may
not heat up to a sufficient temperature for cooking.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment -
WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
FP
FP
FP
en Induction cooking
8
The ferromagnetic area will also be reduced if the
material from which the base of the cookware is
made contains aluminium, for example. This may
mean that the cookware will not become sufficiently
hot or even that it will not be detected.
Unsuitable pans
Never use diffuser hobs or pans made from:
common thin steel
glass
earthenware
copper
aluminium
Properties of the base of the cookware
The material(s) from which the base of the cookware is
made can affect the cooking result. Using pots and
pans made from materials that distribute heat evenly
through them, such as stainless-steel pans with a three-
layer base, saves time and energy.
Use cookware with a flat base; if the base of the
cookware is uneven, this may impair the heat supply.
Absence of pan or unsuitable size
If no pan is placed on the selected hotplate, or if it is
made of unsuitable material or is not the correct size,
the power level displayed on the hotplate indicator will
flash. Place a suitable pan on the hotplate to stop the
flashing. If this takes more than 90 seconds, the
hotplate will switch off automatically.
Empty pans or those with a thin base
Do not heat empty pans, nor use pans with a thin base.
The hob is equipped with an internal safety system.
However, an empty pan may heat up so quickly that the
"automatic switch off" function may not have time to
react and the pan may reach very high temperatures.
The base of the pan could melt and damage the glass
on the hob. In this case, do not touch the pan and
switch the hotplate off. If it fails to work after it has
cooled down, please contact the Technical Assistance
Service.
Pan detection
Each hotplate has a lower limit for pan detection. This
depends on the diameter of the ferromagnetic area of
the cookware and the material from which its base is
made. For this reason, you should always use the
hotplate that best matches the diameter of the base of
the pan.
Getting to know your appliance en
9
*Getting to know your
appliance
Getting to know your appliance
You can find information on the dimensions and power
of the hotplates in~ Page 2
The control panel
Controls
Touching a symbol activates the respective function.
Note: Always keep the control panel clean and dry.
Moisture can prevent it from working properly.
The hotplates
Controls
#
Main switch
$
Selecting a hotplate
A/@
Adjustment fields
Childproof lock
z
Locking the control panel for cleaning
ý
Move function
þ
Combi zone function
˜
PowerBoost function
Keep warm function
0
Timer function
Indicators
Operating status
-Š
Heat settings
‹‹
Timer function
/œ
Residual heat
Childproof lock
˜
PowerBoost function
Keep warm function
ò
Combi zone function and Move function
x
Programming the cooking time
S
Kitchen timer
Min. Time display
÷
Energy consumption
Hotplates
$
Simple hotplate Use cookware that is a suitable size
à
Combined hotplate See section ~ "CombiZone function" or ~ "Move function"
Only use cookware that is suitable for induction cooking; see section ~ "CombiZone function"
en Operating the appliance
10
Residual heat indicator
The hob has a residual heat indicator for each hotplate.
This indicates that a hotplate is still hot. Do not touch a
hotplate while the residual heat indicator is lit up.
The following are shown depending on the amount of
residual heat:
Display : High temperature
Display œ: Low temperature
If you remove the cookware from the hotplate during
cooking, the residual heat indicator and the selected
heat setting will flash alternately.
When the hotplate is switched off, the residual heat
indicator will light up. Even after the hob has been
switched off, the residual heat indicator will stay lit for as
long as the hotplate is still warm.
1Operating the appliance
Operating the appliance
This chapter explains how to set a hotplate. The table
shows heat settings and cooking times for various
meals.
Switching the hob on and off
The main switch is used to switch the hob on and off.
To switch on: Touch the # symbol. An audible signal
sounds. The indicator next to the main switch and the
hotplate indicators light up. The hob is ready to use.
To switch off: Touch the # symbol until the indicator
goes out. All hotplates are switched off. The residual
heat indicator remains lit until the hotplates have cooled
down sufficiently.
Notes
The hob switches off automatically if all hotplates
have been switched off for more than 20 seconds.
The selected settings are stored for four seconds
after the hob has been switched off. If you switch it
on again during this time, the hob will operate using
the previously stored settings.
Setting a hotplate
Use the @ and A symbols to select the required heat
setting.
Heat setting = lowest setting.
Heat setting Š = highest setting.
Every heat setting has an intermediate setting. This is
marked with a dot.
Selecting a hotplate and heat setting
The hob must be switched on.
1. Select the hotplate using the $ symbol.
2. Touch the @ or A symbol within 10 seconds. The
following basic setting appears:
@ symbol: Š heat setting
A symbol: heat setting
The heat setting is set.


Operating the appliance en
11
Changing the heat setting
Select the hotplate and touch the
@ or A symbol until
the required heat setting appears.
Switching off the hotplate
Select the hotplate and then touch the @ or A symbol
until appears.
The hotplate switches itself off and the residual heat
indicator appears.
Notes
If no pan has been placed on the hotplate, the
selected power level flashes. After a certain time has
elapsed, the hotplate switches off.
If a pan has been placed on the hotplate before
switching on the hob, it will be detected within
20 seconds of pressing the main switch and the
hotplate will be selected automatically. Once
detected, select the power level within the next
20 seconds or the hotplate will switch off.
If more than one pan is placed on the hob, only one
will be detected when switching it on.
Chef's recommendations
Recommendations
When heating up puree, cream soups and thick
sauces, stir occasionally.
Set heat setting 8 to 9 for preheating.
When cooking with the lid on, turn the heat setting
down as soon as steam escapes between the lid
and the cookware. Steam does not need to escape
for a good cooking result.
After cooking, keep the lid on the cookware until you
serve the food.
To cook with the pressure cooker, observe the
manufacturer's instructions.
Do not cook food for too long, otherwise the
nutrients will be lost. The kitchen clock can be used
to set the optimum cooking time.
For a more healthy cooking result, smoking oil
should be avoided.
To brown food, fry small portions in succession.
Cookware may reach high temperatures while the
food is cooking. We recommend that you use oven
gloves.
You can find recommendations for energy-efficient
cooking in section ~ "Environmental protection"
Cooking table
The table shows which heat setting is suitable for each
type of food. The cooking time may vary depending on
the type, weight, thickness and quality of the food.
Heat setting Cooking time
(mins)
Melting
Chocolate coating 1 - 1. -
Butter, honey, gelatine 1 - 2 -
Heating and keeping warm
Stew, e.g. lentil stew 1. - 2 -
Milk* 1. - 2. -
Heating sausages in water* 3 - 4 -
Defrosting and heating
Spinach, frozen 3 - 4 15 - 25
Goulash, frozen 3 - 4 35 - 55
Poaching, simmering
Potato dumplings* 4. - 5. 20 - 30
Fish* 4 - 5 10 - 15
White sauces, e.g. Béchamel sauce 1 - 2 3 - 6
Whisked sauces, e.g. sauce béarnaise, hollandaise 3 - 4 8 - 12
* Without lid
** Turn several times
*** Preheat to heat setting 8 - 8.
en Operating the appliance
12
Boiling, steaming, braising
Rice (with double the volume of water) 2. - 3. 15 - 30
Rice pudding*** 2 - 3 30 - 40
Unpeeled boiled potatoes 4. - 5. 25 - 35
Boiled potatoes 4. - 5. 15 - 30
Pasta, noodles* 6 - 7 6 - 10
Stew 3. - 4. 120 - 180
Soups 3. - 4. 15 - 60
Vegetables 2. - 3. 10 - 20
Vegetables, frozen 3. - 4. 7 - 20
Cooking in a pressure cooker 4. - 5. -
Braising
Roulades 4 - 5 50 - 65
Pot roast 4 - 5 60 - 100
Goulash*** 3 - 4 50 - 60
Roasting/frying with little oil*
Escalope, plain or breaded 6 - 7 6 - 10
Escalope, frozen 6 - 7 8 - 12
Chop, plain or breaded** 6 - 7 8 - 12
Steak (3 cm thick) 7 - 8 8 - 12
Poultry breast (2 cm thick)** 5 - 6 10 - 20
Poultry breast, frozen** 5 - 6 10 - 30
Rissoles (3 cm thick)** 4. - 5. 20 - 30
Hamburgers (2 cm thick)** 6 - 7 10 - 20
Fish and fish fillet, plain 5 - 6 8 - 20
Fish and fish fillet, breaded 6 - 7 8 - 20
Fish, breaded and frozen, e.g. fish fingers 6 - 7 8 - 15
Scampi, prawns 7 - 8 4 - 10
Sautéeing fresh vegetables and mushrooms 7 - 8 10 - 20
Stir-fry, vegetables, meat cut in Asian-style strips 7 - 8 15 - 20
Frozen dishes, e.g. roasted dishes 6 - 7 6 - 10
Pancakes (baked in succession) 6. - 7. -
Omelette (cooked in succession) 3. - 4. 3 - 6
Fried eggs 5 - 6 3 - 6
Deep-fat frying* (150-200 g per portion in 1-2 l oil, deep-fat fried in portions)
Frozen products, e.g. chips, chicken nuggets 8 - 9 -
Croquettes, frozen 7 - 8 -
Meat, e.g. chicken portions 6 - 7 -
Fish, breaded or in beer batter 6 - 7 -
Vegetables, mushrooms, breaded or battered, tempura 6 - 7 -
Small baked items, e.g. doughnuts, fruit in batter 4 - 5 -
Heat setting Cooking time
(mins)
* Without lid
** Turn several times
*** Preheat to heat setting 8 - 8.
CombiZone function en
13
wCombiZone function
CombiZone function
Using this function, the two right hotplates, which are
the same size, can be linked together. When doing this,
the same heat setting is set for both hotplates. This is
especially suitable for cooking with elongated
cookware.
Notes regarding cookware
To achieve the best results, use suitable, oval cookware
in the area of both hotplates. Position the cookware in
the middle of the hotplates.
When you are using cookware on just one of the two
hotplates, it can be moved to the second hotplate. In
this case, the heat setting and the selected settings are
transferred.
Activation
The hob must be on.
1. Select one of the two hotplates in the combi zone
and set the heat setting.
2. Touch the þ symbol. The ò indicator lights up.
The heat setting lights up on the displays for the two
hotplates.
The function has now been activated.
Changing the heat setting
Select one of the two hotplates assigned to the combi
zone and use the @ or A symbol to set the heat
settings.
Deactivation
Select one of the two hotplates assigned to this function
and touch the þ symbol.
This deactivates the function. The two hotplates will now
function independently.
uMove function
Move function
You can use this function to link the two right hotplates,
which are the same size, and select a different heat
setting for each of the two hotplates. Preset heat
settings:
Front hotplate = heat setting
Š
Rear hotplate = heat setting
The heat settings can be changed independently of one
another for each hotplate.
Notes
Only place cookware on one of the hotplates. The
function will not be activated if there is cookware on
each of the two hotplates.
The heat setting is less brightly lit on the display for
the hotplate on which there is no cookware. It will not
be activated until the cookware is moved to this
hotplate and is detected.
If the function has already been activated and a
second piece of cookware is placed on the free
hotplate, the display lights up less brightly, as
before. The hotplate is not active. The hotplate is
activated when the first piece of cookware is
removed.
Advice on using cookware
To ensure that the cookware is detected and heat is
distributed evenly, correctly centre the cookware:
Only use one piece of cookware which only covers one
hotplate.
Moving the cookware from one hotplate to another:
en Time-setting options
14
Activation
1. Select one of the two hotplates assigned to the
Move function.
2. Touch the ý symbol. The ò indicator lights up.
The heat settings light up on the displays for each of
the two hotplates.
The function has now been activated.
Notes
The display for the hotplate with the cookware lights
up more brightly.
The ¬ indicator lights up on the display for the
hotplate that is still selected.
Changing the heat setting
Select one of the two hotplates assigned to the Move
function and use the @ or A symbol to set the heat
setting.
Note: If the function is deactivated, the heat settings
return to the preset values
Deactivation
Touch the ý symbol.
This deactivates the function.
Note: When one of the two hotplates is set to , the
function is deactivated within approx. 10 seconds.
OTime-setting options
Time-setting options
Your hob has two timer functions:
Programming the cooking time
Kitchen timer
Programming the cooking time
The hotplate automatically switches off after the time
that is set has elapsed.
Setting procedure:
1. Select the hotplate and the required heat setting.
2. Touch the 0 symbol. x lights up on the display for
the hotplate.‹‹ lights up on the timer display.
3. Touch the @ or A symbol. The basic setting
appears:
@ symbol: 30 minutes.
A symbol: 10 minutes.
4. Use the @ or A symbol to select the required
cooking time.
After a few seconds, the time begins to elapse.
Notes
The same cooking time can be set automatically for
all hotplates. The set time for each of the hotplates
counts down independently from the others.
You can find information on automatically
programming the cooking time in section ~ "Basic
settings"
If the Combi Zone or Move function is selected for
the combined hotplate, the set time for both
hotplates is the same.
Changing or deleting the time
Select a hotplate. Touch the 0 symbol and use the
@ or A symbols to change the cooking time, or set the
time to ‹‹.
When the time has elapsed
The hotplate switches off. An audible signal sounds. ‹‹
lights up in the timer display for 60 seconds.
Touch the 0 symbol. The displays go out and the
audible signal ceases.
Notes
If a cooking time was programmed for several
hotplates, the time information for the selected
hotplate is shown in the timer display.
You can set a cooking time of up to 99 minutes.
 
PowerBoost function en
15
The kitchen timer
You can use the kitchen timer to set a time of up to 99
minutes.
This functions independently from the hotplates and
from other settings. This function does not automatically
switch off a hotplate.
Setting procedure
1. Touch the 0 symbol repeatedly until the V
indicator lights up. ‹‹ lights up on the timer display.
2. Touch the @ or A symbol. The basic setting appears.
@ symbol: 10 minutes.
A symbol: 5 minutes.
3. Use the @ or A symbol to set the required time.
After a few seconds, the time begins to count down.
Changing or cancelling the cooking time
Touch the 0 symbol repeatedly until the V indicator
lights up. Change or set the time to ‹‹ using the @ or
A symbol.
When the time has elapsed
An audible signal sounds. ‹‹ appears in the timer
display. The displays go out after 60 seconds.
By pressing the 0 symbol, the displays go out and the
audible signal ceases.
vPowerBoost function
PowerBoost function
The PowerBoost function enables you to heat up large
quantities of water faster than when using heat setting
Š.
This function can always be activated for a hotplate,
provided the other hotplate in the same group is not in
use (see illustration). Otherwise,
˜ and Š will flash in
the display for the selected hotplate; the
Š heat setting
will then be set automatically without activating the
function.
Note: In the combi zone, the PowerBoost function can
only be activated if the two hotplates are used
independently of each other.
Activation
1. Select a hotplate.
2. Touch the ˜ symbol.
˜ lights up on the display.
The function is activated.
Deactivation
1. Select a hotplate.
2. Touch the ˜ symbol.
The ˜ display goes out and the hotplate switches
back to the Š heat setting.
The function is deactivated.
Note: In certain circumstances, the PowerBoost
function can switch itself off automatically in order to
protect the electronic elements inside the hob.
en Keep warm function
16
zKeep warm function
Keep warm function
This function is suitable for melting chocolate or butter
and for keeping food warm.
Activation
1. Select the required hotplate.
2. Touch the within the next 10 seconds.
lights up on the display.
The function is activated.
Deactivation
1. Select the hotplate.
2. Touch the symbol.
The indicator goes out. The hotplate switches itself
off and the residual heat indicator lights up.
The function is deactivated.
AChildproof lock
Childproof lock
You can use the childproof lock to prevent children
from switching on the hob.
Activating and deactivating the childproof
lock
The hob must be off.
To activate: Touch the symbol for approx. 4
seconds. The indicator lights up for 10 seconds.
The hob is locked.
To deactivate: Touch the symbol for approx. 4
seconds. The lock is released.
Childproof lock
With this function, the childproof lock automatically
activates when a hob is switched off.
Switching on and off
You can find out how to switch the automatic childproof
lock on in the ~ "Basic settings" section
Wipe protection en
17
kWipe protection
Wipe protection
If you wipe over the control panel while the hob is
switched on, settings may be altered. To avoid doing
this, you can use the hob's "Lock control panel for
cleaning" function.
To activate: Touch the
z symbol. You will hear an
audible signal. The control panel is locked for
35 seconds. You can now wipe over the surface of the
control panel without altering any settings.
To deactivate: The control panel will be unlocked once
35 seconds have elapsed. To release the function early,
touch the
z symbol.
Notes
An audible signal sounds 30 seconds after
activation. This indicates that the function is about to
finish.
The cleaning lock does not lock the main switch. The
hob can be switched off at any time.
bAutomatic safety cut-out
Automatic safety cut-out
If a hotplate operates for an extended period and no
settings are changed, the automatic safety shut-off is
activated.
The hotplate stops heating. , and the residual heat
indicator œ or flash alternately in the hotplate display.
When you touch any symbol, the display switches off.
The hotplate can now be set again.
The point at which the safety shut-off becomes active
depends on which heat setting has been set (after 1 to
10 hours). .
en Basic settings
18
QBasic settings
Basic settings
The appliance has various basic settings. You can
adapt these to suit your cooking habits.
Display Function
™‚
Automatic childproof lock
Manual*.
Automatic.
ƒ Function deactivated.
™ƒ
Audible signals
Confirmation and fault signals are switched off.
Only the fault signal is switched on.
ƒ Only the confirmation signal is switched on.
All signal tones are switched on.*
™„
Display energy consumption
Switched off.*
Switched on.
™†
Automatically programming the cooking time
‹‹ Switched off.*
‹‚-ŠŠ Time until automatic switch-off.
™‡
Duration of the timer-end signal tone
10 seconds.
ƒ 30 seconds.
1 minute.*
™ˆ
Power management function. Limiting the total power of the hob
Switched off.*
1000 W minimum power.
. 1500 W.
ƒ 2000 W.
...
Š or Š. Maximum power of the hob.
™Š
Time for selecting the hotplate
Unlimited: The hotplate that was set last remains selected.*
Limited: The hotplate only remains selected for a few seconds.
™‚ƒ
Checking cookware and cooking results
Not suitable
Not perfect
ƒ Suitable
™‹
Restoring the factory settings
Individual settings.*
Restore factory settings.
* Factory settings
Energy consumption indicator en
19
To access the basic settings:
The hob must be off.
1. Switch on the hob.
2. Within ten seconds, touch and hold the z symbol
for approximately four seconds.
The first four displays provide product information.
Touch the @ or A symbol to view the individual
displays.
3. Touch the z symbol again to access the basic
settings.
and flash alternately on the displays and
appears as a presetting.
4. Touch the z symbol repeatedly until the required
function is displayed.
5. Then use the @ and A symbols to select the
required setting.
6. Touch the z symbol for at least four seconds.
The settings have been saved.
Leaving the basic settings
Turn off the hob with the main switch.
[Energy consumption
indicator
Energy consumption indicator
This function indicates the total amount of energy
consumed by this hob the last time it was used for
cooking.
Once switched off, the energy consumption in kWh is
displayed for 10 seconds.
The picture shows an example with an energy
consumption of .‹‰ kWh.
You can find out how to switch this function on in the
section on ~ "Basic settings"
Product information Display screen
After-sales service index (ASSI)
‹‚
Production number
”š
Production number 1
Š†.
Production number 2
.
en Cookware check
20
tCookware check
Cookware check
This function can be used to check the speed and
quality of the cooking process depending on the
cookware.
The result is a reference value and depends on the
properties of the cookware and the hotplate being used.
1. Place the cold cookware containing 200 ml of water
on the centre of the hotplate the diameter of which
best matches that of the base of the cookware.
2. Go to the basic settings and select the setting ™‚ƒ.
3. Touch the @ or A symbol. A flashes in the hotplate
display.
The function is activated.
After 10 seconds, the result for the quality and speed of
the cooking process appears in the hotplate display.
Check the result using the following table:
To activate the function again, select the @ or A symbol.
Notes
If the diameter of the hotplate used is much smaller
than the diameter of the cookware, only the middle
of the cookware can be expected to heat up. This
may result in the cooking results not being as good
as expected or being less than satisfactory.
You can find information on this function in the
section on ~ "Basic settings".
You can find information on the type, size and
positioning of the cookware in the section on
~ "Induction cooking".
DCleaning
Cleaning
Suitable maintenance and cleaning products can be
purchased from the after-sales service or in our e-Shop.
Hob
Cleaning
Always clean the hob after cooking. This will prevent
food deposits from becoming burned on. Only clean the
hob after the residual heat indicator has gone out.
Clean the hob with a damp dish cloth and dry it with a
cloth or towel to prevent limescale build-up.
Only use cleaning agents that are suitable for this type
of hob. Observe the manufacturer's instructions on the
product packaging.
Never use:
Undiluted washing-up liquid
Cleaning agents designed for dishwashers
Abrasive cleaners
Harsh cleaning agents, such as oven spray and
limescale remover
Scouring pads
High-pressure cleaners or steam jet cleaners
Stubborn dirt is best removed with a glass scraper,
available from retailers. Observe the manufacturer's
instructions.
You can obtain a suitable glass scraper from customer
services or through our online shop.
Using a special sponge for cleaning glass-ceramic
hobs achieves a great cleaning result.
Note: Do not use any cleaning agents while the hob is
still hot. This may mark the surface. Make sure that any
residue left by cleaning agents is removed.
Hob surround
To prevent damage to the hob surround, observe the
following instructions:
Only use warm soapy water
Wash new dish cloths thoroughly before use.
Do not use harsh or abrasive cleaning agents.
Do not use a glass scraper or sharp objects.
Result
The cookware is not suitable for the hotplate and will therefore
not heat up.*
The cookware is taking longer to heat up than expected and the
cooking process is not going as well as it should.*
ƒ
The cookware is heating up correctly and the cooking process
is going well.
* If there is a smaller hotplate available, test the cookware again on the
smaller hotplate.
Potential marks
Limescale and water
marks
Clean the hob as soon as it has cooled down.
You can use a cleaning agent suitable for
glass-ceramic hobs.*
Sugar, rice starch or
plastic
Clean immediately. Use a glass scraper. Cau-
tion: Risk of burns.*
* Then clean with a damp dish cloth and dry with a cloth or towel.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Neff T48PD23X0 Operating instructions

Category
Hobs
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI