Bauknecht TGE 4407-1SW Program Chart

Brand: Bauknecht

Model: TGE 4407-1SW

Type: Program Chart

Bauknecht TGE 4407-1SW gas cooktop offers innovative features for a seamless cooking experience. With automatic burner lighting, you can simply turn the knob without holding it down or using a separate igniter. The burner knobs can be turned in both directions for quick and precise adjustments. The ON/OFF push-button provides immediate control over all burners, ensuring safety and convenience. Enjoy peace of mind with automatic relighting in case of accidental burner熄火.

5019 619 61201

TGE 4407 PRODUCT DESCRIPTION SHEET



INNOVATIVE COOKTOP

FEATURES

The gas cooktop you have bought has some

innovative features, compared with traditional gas

cooktops.

• Easy burner lighting after switching the

cooktop on with the ON/OFF button just turn

the knob. There is no need to keep it pressed

down or to press a separate igniter.

• The burner knob can be turned in both

directions: to the right the burner goes to

the minimum, to the left it goes directly to

the maximum. There is no need to go

through the other levels.

•The ON/OFF push-button turns off all the

working burners immediately, so that you

can act quickly if there is an unexpected

situation on the cooktop (water spill,

dangerous situation with children, etc.).

• With automatic relighting the cooktop

can react to the burner being turned off,

relighting it automatically. If relighting

happens too frequently, however, the

cooktop recognises that there is something

wrong and informs the user. This avoids

continuous attempts to relight which could

make the product dangerous.

•The minute counter can be used when the

cooktop is being used, for cooking needs, and

when the product is switched off for needs not

directly linked to the cooktop.

• Instead the timer can operate directly on

the burner, turning it off automatically at

the end of the set time.

• The timer can be used both with a burner

turned off, and with a burner already lit,

where cooking is taking place, just by turning

the corresponding knob: this function can be

useful when cooking must continue for a set

number of minutes once the water is boiling.

•The timer can also be switched off

without turning the burner off, as at the

end of normal timer use: cooking can then

continue for as long as wished without

turning the burner off.

• Residual heat pilot lights at the cooktop

centre indicate that the grid is still hot.

• Attention: When switching on the

cooktop after a power failure, the

residual heat pilot lights remain off,

even if the grids are still hot.

1. Removable grids

2. Large burner

3. Rear medium burner

4. Front medium burner

5. Auxiliary burner

6. Control panel

Warning

Improper use of the grids can result in

damage to the hob: do not position the

grids upside down or slide them across

the hob.

Do not use:

cast iron griddles or terracotta pots

and pans

heat diffusers such as metal mesh, or

any other types

two burners simultaneously for one

receptacle (e.g. fish kettle).

DIMENSIONS OF THE COOKTOP AND

THE WORKING SURFACE (in mm)

•Using the search for the minimum the

cooktop can automatically identify the

lowest minimum compatible with the local

gas network distribution conditions at the

time the function is used. The burner can

thus be used for long cooking at the lowest

level possible, without turning the knob in

the OFF direction, as in traditional cooktops,

when the knob minimum is too high.

• When searching for the minimum the knob

checks the flame continuously through its

range, as it has a direct flame-knob link on

all its rotation.

• As in modern cars this cooktop has self-

diagnosis capacity and can signal abnormal

situations which require the help of the

Technical After-Sales Service.

DESCRIPTION OF THE KNOBS AND COOKTOP OPERATION

COOKTOP OPERATION

• Switch on the cooktop by pressing button

. Pilot light comes on. The cooktop is

ready for use.

• Turn the knob corresponding to the burner

to be used to the position required. The

pilot light near the knob and the residual

heat light come on.

• As soon as the knob is turned the burner

lights completely automatically: a pulsing

noise indicates that the safety and gas

control systems have been activated and are

working correctly.

• To turn off the burner turn the knob to “0”.

Switch off the cooktop by pressing button

. The pilot light goes out.

N.B.:

— If the burner goes out automatically

(draught, spilt liquids, etc.) the burner

relights automatically.

— If this happens too often, the cooktop

recognises the abnormal situation, turns off the

burner involved, sounds a warning and flashes

“0”. In this case turn the knob to “0”.

— If at the end of cooking the cooktop is not

switched off by pressing button , after a

few minutes pilot light begins to flash and

an acoustic signal is given, until the cooktop

is switched off.

— This obligatory switching off function reduces

the consumption of electricity when the

product is not working and also makes sure

that the product cannot be switched on by

accident (knocking the knobs, faults, etc....)

— If the cooktop is used for too long, the

display indicates “H” and the cooktop

switches off until the electronic components

cool down. The indication “H” then flashes.

Turn the knob to “0” and light the burners

again, if necessary.

1. Front medium burner control

knob

2. Rear medium burner control

knob

3. Large burner control knob

4. Auxiliary burner control knob

5-6-7-8. Knob pilot lights

9-10. Timer/minute counter buttons

11. Signal display (Timer/Faults)

12-13-14-15. Timer section pilot

light

16. ON pilot light

17. ON/OFF button

18-19-20-21. Residual heat pilot

light



If the burners will not light

• The burner will stop automatically within

22 seconds.

• One of pilot lights or flashes and

an acoustic signal sounds.

• Turn the knob back to “0”.

• Look for the cause (see “Trouble Shooting

Guide” in the separate instruction booklet)

and repeat the lighting operations.

If the system stops one of the burners:

• Turn the burner off and turn the knob back

to “0”.

• Look for the cause (see “Trouble Shooting

Guide” in the separate instruction booklet).

• Repeat the lighting operations.

To switch off all the burners at the same

time in an emergency (e.g. food spills

over, etc.):

• Press button . The pilot lights of the lit

burners flash.

• Remember to put all the knobs back to

“0” because if the cooktop is used again

and the knobs have not been zeroed, a

buzzer will sound.

OPERATION OF THE TIMER/

MINUTE COUNTER (Maximum

time: 99 minutes)

To use the MINUTE COUNTER:

• Select the cooking time required by pressing

buttons or . The set time appears on

display and the 4 pilot lights and

come on for a few seconds.

• a few moments after selection, the

minute counter starts to count down and a

buzzer sounds.

• When the set time has elapsed a buzzer

sounds.

• To zero press buttons and at the same

time or zero the time by pressing button .

N.B.:

The minute counter works even with the

cooktop switched off.

To use the TIMER:

— The timer function can be used for any

burner, whether turned off or already lit.

1) Select the cooking time required by pressing

buttons or . The set time appears on

display and the 4 pilot lights and

come on for a few seconds.

2) Turn the burner knob to the position

required before the pilot lights go out.

The pilot light corresponding to the burner

chosen lights up.

N.B.:

If the knobs are not turned before the pilot

lights go out, the minute counter function is

switched on.

3) When the set time has elapsed, the burner

goes out automatically and the timer and

knob pilot lights flash.

The acoustic signal sounds.

• Turn the knob back to “0”:

To stop the timer:

a) To zero the time and switch off the

burnerturn button or turn the knob to

“0”.

b) To cancel the timer function press buttons

and at the same time.

The burner remains lit.

N.B.:

the residual heat pilot lights stay on even

when the cooktop is OFF, until the burner has

cooled down.

AUTOMATIC SEARCH AND

SETTING OF THE MINIMUM

• Turn the burner control knob to symbol .

After a few seconds small bars light up on

display and the residual heat pilot light

flashes for a few seconds until the search is

complete, confirmed by an acoustic signal.

The burner searches for the minimum and

set it automatically.

• If the knob is positioned on the automatic

search and setting of the minimum, the

burner lights again until the gas has reached

the correct flow rate.

DIMENSIONS OF THE COOKTOP AND

THE WORKING SURFACE (in mm)

NOTE: If the distance “A“ between the wall cabinets is between 660 mm and

680 mm, the height “B” must be a minimum of 520 mm.

If the distance “A” between the wall cabinets is greater than the width

of the cooktop, the height “B” must be a minimum of 400 mm.

In case of installation of a hood above the cooktop, please refer to the

hood instructions for the correct distance.

INJECTOR TABLE CATEGORY II2L3B/P

Type of

gas used

Type of

burner

Gas

type

code

No.

Injector

marking

ø 100/mm

Rated

thermal

flow

rate

Rated

consump-

tion

Low

thermal

nominal

flow rate

Gas pressure

min. rated max.

NATURAL GAS

(Methane) G 25

High-speed

Medium-speed

Auxiliary

145

103

3.00

1.65

1.00

332 l/h

183 l/h

111 l/h

1.20

1.00

0.70

20 25 30

LIQUID

PETROLEUM GAS

(Butane/Propane)

G 30/G 31

High-speed

Medium-speed

Auxiliary

3.00

1.65

1.00

218 g/h

120 g/h

73 g/h

1.20

1.00

0.70

25 30 35

Type of gas

used

Type of

appliance

Total rated

thermal flow rate

Total rated

consumption

Air needed

for combustion

G 25 25 mbar

4 gas 7.30 809 l/h 14.6

G30/G3130 mbar

4 gas 7.30 531 g/h 14.6

Bauknecht TGE 4407-1SW Program Chart

Bauknecht TGE 4407-1SW Program Chart

Bauknecht TGE 4407-1SW Program Chart

Other documents