Webb WER18SP User manual

Brand: Webb

Model: WER18SP

Category: Lawnmowers

Type: User manual

OPERATOR’S MANUAL AND PARTS LIST

SELF PROPELLED PETROL LAWNMOWER

WER18SP

Spares & Support: 01793 333212

www.webblawnmowers.co.uk

Before use please read & understand this manual, paying particular attention to

the safety instructions.

16/06/2014

Thank you for choosing our petrol lawnmower.

To ensure that you get the best results from your petrol lawnmower please read all of these safety and

operating instructions carefully before using this product.

TABLE OF CONTENTS PRODUCT SPECIFICATION

Product Specifications…………………….1

Safety Rules……………………………..1-3 Model number WER18SP (193803001)

Assembly/Pre-Operation………………...3-5 Petrol engine B&S 450e series 125cc

Operation………………………………...6-8 Engine speed 2800rpm

Maintenance……………………………...8-9 Cutting width 457mm

Storage………………………………………9 Adjustable cutting height 15-65mm

Environment…………………….………….10 Grass collection capacity 60L

Symbols…………………………………….10 Steel deck

Parts Diagram and Lists...………………11-16 Sound Pressure Level 80.5 dB(A)

DOC………………………………………..17 Guaranteed Sound Power Level 96dB(A)

Also Available From Webb…………….......18 Max. vibration value 6.360m/ s

IMPORTANT: Failure to observe the following safety instructions could result in serious injury.

WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making

repairs, always the disconnect the spark plug lead.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after

engine has stopped. To avoid severe burns on contact, stay away from these areas.

Drive lever

Brake lever

Grass catcher

Height adjust handle

Quick fix handle

B&S 450E series

Water nozzle

1. GENERAL OPERATION AND SAFETY RULES

z Read the instructions carefully. Be familiar with the controls and the proper use of the equipment.

z Do not put your hands or feet near or under rotating parts. Keep clear of the discharge opening at all

times.

z Only allow responsible individuals, who are familiar with the instructions, to operate the machine.

z Thoroughly inspect the area where equipment is to be used and remove all objects, which could be

thrown by the machine.

z Never mow while people, especially children, or pets are nearby.

z While mowing, always wear appropriate footwear and trousers. Do not operate the equipment when

barefoot or wearing open sandals.

z Do not pull the mower backwards unless absolutely necessary.

z Never operate the lawnmower with defective guards, or without safety devices, for example

deflectors and/or grass catchers, in place.

z Only use accessories approved by the manufacturer.

z Stop the blade(s) when crossing gravel drives, paths, or roads.

z Stop the engine and disconnect the spark plug:

- before clearing blockages or unclogging the chute.

- before checking, cleaning or working on the lawnmower.

- after striking a foreign object. Inspect the lawnmower for damage and make repairs before

restarting and operating the lawnmower.

- if lawnmower starts to vibrate abnormally (check immediately).

z Shut the engine off and wait until it has come to a complete stop before removing the grass catcher.

z Mow only in daylight or good artificial light.

z Do not operate the machine while under the influence of alcohol or drugs.

z Never operate machine in wet grass, this could cause slipping.

z Keep a firm hold on the handle and walk; never run.

z Disengage the self-propelled mechanism before starting the engine.

z Always wear safety goggles or safety glasses with side shields when operating the mower.

z Remove obstacles such as rocks, tree limbs, etc.

z Watch for holes, ruts, or bumps. Tall grass can hide obstacles.

z Do not trim near drop-offs, ditches or embankments. The operator could lose their footing or balance.

z Do not mow excessively steep slopes.

z Keep in mind that the operator or user is responsible for accidents or hazards involving the machine

that could occur to other people or their property.

z Be alert and turn the machine off if children enter the area.

z For wheel

ed rotary machines, mow across the face of slopes, never up and down.

z Never allow children or people unfamiliar with these instructions to use the lawnmower.

z WARNING-Petrol is highly flammable.

- store fuel in containers specifically designed for this purpose;

- refuel outdoors only and do not smoke while refueling;

- add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the

engine is running or when the engine is hot;

- if petrol is spilled, do not attempt to start the engine but move the machine away from the area

of spillage and avoid creating any source of ignition until the petrol vapours have dissipated;

- replace fuel tanks and container caps securely.

z Before using, always visually inspect to ensure that the blade, blade bolts and cutter assembly are not

worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance.

z Never tamper with safety devices. Regularly check that they are operating properly.

z Keep the machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow the

machine to cool before storing.

z Exercise extreme caution when changing direction on slopes.

z Never attempt to make wheel height adjustments while the engine is running.

z Grass catcher components are subject to wear, damage, and deterioration, which could expose

moving parts or allow objects to be thrown. Frequently check components and replace with the

manufacturer’s recommended parts, when necessary.

z The mower blades are extremely sharp. Wrap the blade, wear gloves, and use extra caution when

servicing them.

z Do not change the engine governor setting or over-rev the engine.

z Stop the engine if the lawnmower has to be tilted for transportation when crossing surfaces other than

grass, and when transporting the lawnmower to and from the area to be mowed.

z Disengage the drive clutch before starting the engine.

z Start the engine carefully according to the instructions, with your feet well away from the blade.

z Do not tilt the lawnmower when starting the engine or cutting.

z Do not start the engine when standing in front of the discharge chute.

z Never pick up or carry a lawnmower while the engine is running.

ASSEMBLY/PRE-OPERATION

Read this instruction manual in its entirety before you assemble or operate your new lawnmower.

IMPORTANT: The lawnmower is shipped WITHOUT OIL OR PETROL in the engine.

Your new lawnmower has been assembled and tested at the factory.

Roll the lawnmower out of the carton and check the carton thoroughly for additional loose parts.

To avoid damage during the transport process, the drive and brake cables for your machine may not be

fitted to their appropriate handle bar.

The front cable is the brake cable, which is to be fitted to the front lever on your machine, this is the

Operator Presence Control Lever (OPC). The cable at the rear is your drive cable, which is to be fitted to

the rear lever, which is your Drive Lever.

Brake Cable

Drive Cable

Apply inward pressure to the lever assembly on the left hand side of the machine, to remove the lever lug

from the handle assembly.

Insert the Brake Cable into the OPC Lever.

Insert the Drive Cable into the Drive Lever.

Re-seat the lever assembly back into the main handle.

INSTALL ATTACHMENTS

Your lawnmower was shipped ready to be used as a rear bag mower.

The mower has three different operating modes.

1. Collecting:

• Fit the grassbox by lifting the rear flap on the mower and hook the front of the box to the shaft on the

mower.

• Lower the flap to lock the grassbox in position.

• When the box is full, the grass will be visible through the viewing window in the top of the box.

• Stop the engine before emptying the grassbox.

2. Rear Discharge:

• With the grassbox removed and the rear flap in the down position, the mower will cut and discharge the

grass from the rear of the machine.

3. Mulching:

• Fit the mulch plug to the rear discharge opening of the mower and close the rear flap.

• The mower will now recycle the chopped grass into the lawn surface.

• To mulch efficiently only cut one third of the length of the grass.

SET UP YOUR MOWER

IMPORTANT: Unfold the handle carefully so

as not to pinch or damage the control cables.

1. Depress the Operator Presence Control Bar

(OPC) and raise the handles until the lower handle

section locks into place at the mowing position.

2. With the Operator Presence Control Bar still

depressed raise the upper handle section into place

on the lower handle and tighten both handle knobs.

OPERATION

Operator Presence Control (OPC) Bar - must be held down to the handle to start the engine. Release to

stop the engine.

Starter rope - used to start the engine.

Drive control lever - used to engage self- propelled motion of the lawn mower.

LAWNMOWER ENGINE SPEED

The engine speed was set at the factory for optimum performance. Speed is not adjustable.

DRIVE CONTROL (Model: WER18SP)

z The drive is controlled by holding the Operator Presence Control bar down to the handle and pulling

the drive control lever back towards the handle.

z Forward motion will stop when the operator presence control bar is released. To stop forward motion

without stopping the engine release the drive control lever until the drive control disengages and hold the

operator presence control bar down against handle to continue mowing without the drive.

ADJUST CUTTING HEIGHT

Lower the cutting deck for a low cut and raise the deck for a high cut; adjust cutting height to suit your

requirements. Medium position is best for most lawns.

BEFORE STARTING ENGINE ADD OIL

Before each subsequent use the oil level must be checked and if necessary topped up with SAE30 engine

oil.

OIL FILLER CAP/DIPSTICK

Your lawnmower is shipped without oil in the engine.

CAUTION: DO NOT overfill the engine with oil, or it will smoke heavily from the muffler on startup.

1. Be sure that the lawnmower is on level ground.

2. Remove the oil dipstick from the oil fill spout.

3. Insert and tighten the dipstick.

IMPORTANT:

z Check the oil level before each use. Add oil if needed. Fill to the full line on the dipstick.

z Change the oil after every 25 hours of operation or each season. You may need to change the oil

more often under dusty, dirty conditions. See “TO CHANGE ENGINE OIL” in the Maintenance

section of this manual.

ADD PETROL

z Fill fuel tank to the bottom of the tank filler neck. Do not overfill. Use fresh, clean, regular unleaded

petrol. Do not mix oil with petrol. Purchase fuel in quantities that can be used within 30 days to

assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use petrol near an open flame.

FUEL TANK CAP

UPPER LIMIT

LOWER LIMIT

CAUTION: To avoid engine problems, the fuel system should be emptied before being stored for 30 days

or more. Empty the fuel tank, start the engine and let it run until the fuel lines and carburettor are empty.

Use fresh fuel for your next use of the machine. See Storage Instructions for additional information.

Never use engine or carburettor cleaner products in the fuel tank or permanent damage may occur.

START ENGINE

To start the engine, first make sure that the spark plug is tightened and that the machine is filled with

sufficient oil and petrol.

NOTE: Due to the protective coating on the engine, a small amount of smoke may be present during the

initial use of the product and should be considered normal.

Press the primer bulb 3 times to allow fuel into the engine (for the first use, press 5 times).

Hold the Operator Presence Control bar down to the handle and pull the starter handle quickly.

Do not allow the starter rope to snap back.

STOP ENGINE

z To stop engine, release the Operator Presence Control bar.

z Disconnect the spark plug cap if the lawnmower is to be left unattended.

MOWING TIPS

z Under certain conditions, such as very tall grass, it may be necessary to raise the height of the cut to

reduce the pushing effort and to keep from overloading the engine and leaving clumps of grass

clippings. It may also be necessary to reduce ground speed and/or run the lawnmower over the area a

second time.

z For extremely heavy cutting, reduce the width of cut by overlapping the previously cut area and mow

slowly.

z Pores in cloth grass catchers can become filled with dirt and dust during use and catchers will collect

less grass. To prevent this, regularly hose the catcher off with water and let it dry before using.

z Keep the top of the engine around the starter clean and clear of grass clippings and chaff. This will

assist engine air flow and extend engine life.

MAINTENANCE

IMPORTANT-Regular, careful maintenance is essential for keeping the safety level and original

performance of the machine unchanged over time.

1) Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. Regular

maintenance is essential for safety and performance.

2) Never store the equipment with fuel in the tank inside a building where vapour may reach a flame,

spark or source of extreme heat.

3) Allow the engine to cool before storing in an enclosed space.

4) To reduce the fire hazard, keep the engine, exhaust silencer, battery compartment and fuel storage area

free of grass, leaves, or excessive grease. Remove grass cuttings from containers before storage.

5) Do not use equipment with worn or damaged parts. Parts should be replaced not repaired. Only use

genuine spare parts. Parts that are not of the same quality can damage the equipment and create safety

hazards.

6) If the fuel tank has to be drained, this should be done outdoors and when the engine is cool.

7) Wear strong work gloves when removing and reassembling the blade.

8) Check the blade’s balance after sharpening.

9) Check the self-closing guard and grass-catcher frequently for wear and deterioration.

10) Whenever the machine is to be handled, transported or tilted you must:

- Wear strong working gloves.

- Grasp the machine at the points that offer a safe grip, clear of the blade and taking account of the weight

of the machine and its distribution.

CLEANING

Your lawnmower has been supplied with a hose pipe connector towards the back of the deck. This enables

you to clean your machine, using your garden hose. Clip the hose to the machine using a standard hose

connector. Turn on your tap. Ensure that any trailing hose is away from the machine deck. Start the

machine. The momentum of the blade rotation will force water around the deck to clean it.

Carefully clean the machine after each cut to ensure an easy start-up next time you use the machine. Be

sure to remove grass debris and mud accumulated inside the chassis before it dries.

If you need to tilt the mower while cleaning always tip it backwards towards the handles, do not tip it on

its side as this will cause oil to enter the carburettor or exhaust.

The paintwork on the inside of the chassis may peel off over time due to the abrasive action of the cut

grass; when this occurs you must touch up the paintwork using a rustproof paint as soon as possible to

prevent the formation of rust that would lead to corrosion of the metal.

Remove the transmission casing by removing the screws and clean around the transmission and drive

belts with a brush or compressed air once or twice a year.

Once every season, the drive wheels should be cleaned internally. Remove both wheels. Clean the gear

wheel and the wheel gear rim of grass and dirt using a brush or compressed air.

CHANGING BLADES

Empty the oil tank before removing the blade.

To replace the blade, undo the screw.

Reinstall as illustrated. Tighten the screw properly. Tightening torque 45 Nm.

When replacing the blade, the blade screw should also be replaced.

STORAGE

The same petrol must not remain in the tank for more than one month.

Thoroughly clean the mower and store it indoors in a dry place.

THE ENVIRONMENT

In order to protect the environment, we recommend that the following points should be given special

consideration:

z Always use pure unleaded petrol.

z Always use a funnel and/or petrol can with a level control to avoid spillage when refilling the fuel

tank.

z Do not fill the fuel tank completely.

z Do not overfill with engine oil.

z When changing the oil, ensure that all the used oil is collected. Avoid spillage. Take the used oil to a

recycling unit.

z Do not dispose of used oil in a rubbish bin. Take it to a recycling unit.

z Replace the silencer if faulty. Always use the Manufacturer’s original spare parts.

z Always seek professional help when the carburretor requires adjustment.

z Clean the air filter according to the instructions.

SYMBOLS

The following symbols can be found on the machine to remind you of the care and attention that are

required during use. The symbols mean:

Important: Read the instruction manual Warning! Beware of objects being thrown out.

before using your lawn mower Ensure bystanders are at a safe distance.

Warning! Before starting any repair work, Warning! Keep hands and feet clear of the

remove the spark plug cap from the cutting deck when the machine is running.

spark plug.

Warning! Ensure other people are at a Drive and stop mower

safe distance when using this

lawnmower.

PARTS DIAGRAM AND LIST – HANDLE ASSEMBLY

Item No Part Number Description Qty Item No Part Number Description Qty

1 WE114-1 Foam Handle Cover 1 14 WE113-14 Pin 6x20 2

2 WE114-2 Brake Lever 1 15 WE113-15 Bolt for Quick Lock Handle 2

3 WE114-3 Self-Propelled Lever 1 16 WE113-16 Lock for Quick Lock Handle 2

4 WE113-4 Top Handle 1 17 WE113-17 Flat Washer 8.4x16x1.6 4

5 WE113-5 Pull Rope Guide 1 18 WE113-18 Lock Nut 2

6 WE113-6 Cap NutM6/8.8 1 19 WE113-19 Hex Nut M8 4

7 WE113-7 Brake Cable Assembly Plate 1 20 WE113-20 Lower Handle 1

8 WE113-8 Bolt M6x30 2 21 WE113-21 Cable Fastener 1

9 WE113-9 Lock Nut M6/8.8 2 22 WE113-22 Hex Bolt M8x16 2

10 WE113-10 Plastic Stopper 1 23 WE113-23 Square Neck Bolt M8x30 2

11 WE113-11 Brake Cable 1 24 WE113-12 Lock Nut M8/8.8 2

12 WE114-4 Self-Propelled Cable 1 25 WE113-3 Triangle knob 2

13 WE113-13 Quick Lock Handle 2

PARTS DIAGRAM AND LIST – DECK ASSEMBLY

Item

Part

Number

Description Qty

Item

Part

Number

Description Qty

1 WE113-24 Deck 1 12 WE113-35 Rear Drive Right Bracket 1

2 WE113-25 "O" Ring 11.2x2.65 1 13 WE113-36 Rear Drive Left Bracket 1

3 WE113-26 Inlet 1 14 WE113-37 Hex Self-Tapping screw M6x10 4

4 WE113-27 Pipe Connector Nut M12x1.25 1 15 WE113-38 Height Adjustment Spring 1

5 WE113-28 Cable Stopper 1 16 WE113-39 Height Adjustment Rod 1

6 WE113-29 Left Handle Bracket 1 17 WE113-40 R Pin 1.5x25 2

7 WE113-30 Right Handle Bracket 1 18 WE113-41 Bolt M6x12 2

8 WE113-31 Hex Bolt M8x14 4 19 WE113-42 Lock Nut M6 2

9 WE113-32 Lock Nut M8 6 20 WE113-47 Mulch Plug 1

10 WE113-33 Height Adjustment Board 1 21 WE113-48 B&S 450E Petrol Engine 1

11 WE113-34 Square Neck Bolt M8x15/8.8 2

PARTS DIAGRAM AND LIST – FRONT AXLE ASSEMBLY

Item No Part Number Description Qty

1 WE113-49 Front Axle 1

2 WE113-50 Front Wheel 2

3 WE113-51 Wheel Bearing 4

4 WE113-52 Lock Nut M8 2

5 WE113-53 Wheel Trim 2

6 WE114-5 Inner Wheel Cover 2

PARTS DIAGRAM AND LIST – REAR AXLE ASSEMBLY

Item No Part Number Description Qty Item No

Part

Number

Description Qty

1 WE113-54

Rear Axle with Height

Adjustment Handle

1 10 WE114-14 Drive Cog L 1

2 WE114-6 Gearbox Assembly 1 11 WE114-15 Drive Cog R 1

3 WE114-7 Bush 2 12 WE114-16 Drive Pin 6

4 WE114-8 Bearing 6001RS 2 13 WE113-56 Rear Wheel 2

5 WE114-9 Self-Propelled Spring 1 14 WE113-51 Wheel Bearing 4

6 WE114-10 Inner Wheel Cover 2 15 WE113-52 Lock Nut M8 2

7 WE114-11 Spring Washer 12 6 16 WE113-57 Rear Wheel Trim 2

8 WE114-12 Ratchet Washer 4 17 WE114-17 Drive V Belt 1

9 WE114-13 "O" ring 11.2x2.65 2

PARTS DIAGRAM AND LIST – GRASS COLLECTOR ASSEMBLY

Item No Part Number Description Qty

1 WE113-58 Grass Box Frame 1

2 WE113-59 Grass Box Top 1

3 WE113-60 Filter Plate 1

4 WE113-61 60L Grass Box Bag (Unbranded) 1

5 WE113-62 Rear Discharge Cover 1

6 WE113-63 Rear Discharge Cover Shaft 1

7 WE113-64 Rear Discharge Cover Spring 1

8 WE113-65 Lock Washer 6 2

9 WE113-66 Rear Discharge Cover Dust Board 1

10 WE113-67 R Pin 1.5x25 2

PARTS DIAGRAM AND LIST – BLADE ASSEMBLY

Item No Part Number Description Qty

1 WE114-18 Blade Adapter Assy 1

2 WE113-69 18" Double Edge Blade 1

3 WE113-70 Blade Washer 1

4 WE113-71 50mm Hex Flange Bolt 1

5 WE114-19 Chassis Bushing 2

6 WE114-20 Hex Self-Tapping Screw 3/8-16x1ST-30mm 2

7 WE114-21 Hex Self-Tapping Screw 3/8-16x1ST 1

8 WE114-22 Belt Cover 1

WER18SP

80.5dB

(

)

125cc

GUARANTEE

This product is guaranteed against manufacturing defects for a period of 24 months.

This does not cover the product where the fault is due to misuse, abuse, use in

contravention of the instructions, or where the product has been the subject of

unauthorised modifications or alterations. This warranty only covers domestic use

and will be void if the tool is used for a commercial application. In the event of a

problem with the product within the guarantee period, please contact Customer

Service on 01793 333212 or email [email protected]. If the

issue cannot be resolved over the telephone or by email, you may be referred to your

local approved service dealer.

Please keep your sales receipt as proof of purchase

Your statutory rights remain unaffected. Guarantor: Handy Distribution SN3 4NS

Whilst every effort is made to accurately represent the product, small variations in

colour, design and specification may occur. We reserve the right to alter the product

without giving notice. All images are illustrative only and may differ from the product

due to ongoing product development.

•

Page is loading ...

Webb WER18SP User manual

Brand: Webb

Model: WER18SP

Category: Lawnmowers

Type: User manual

Download PDF

report

Webb WER18SP User manual

Webb WER18SP User manual

Related papers

Other documents