TOA HY-TM7B-WP User manual

Category
AV equipment stands
Type
User manual

This manual is also suitable for

TOA HY-TM7B-WP is a speaker rigging bracket designed for use with TOA's HX-7B-WP or HX-7W-WP Speaker Systems. It allows for the safe and secure mounting of these speaker systems from ceilings, beams, or other building structures, including under outdoor eaves.

The bracket is made of stainless steel with a black, semi-gloss paint finish, and it has dimensions of 433 (w) x 57 (h) x 295 (d) mm (17.05" x 2.24" x 11.61"). It weighs 2.5 kg (5.51 lb) and comes with all necessary hardware for installation.

The bracket is designed to be used with two speakers, one mounted on each end.

TOA HY-TM7B-WP is a speaker rigging bracket designed for use with TOA's HX-7B-WP or HX-7W-WP Speaker Systems. It allows for the safe and secure mounting of these speaker systems from ceilings, beams, or other building structures, including under outdoor eaves.

The bracket is made of stainless steel with a black, semi-gloss paint finish, and it has dimensions of 433 (w) x 57 (h) x 295 (d) mm (17.05" x 2.24" x 11.61"). It weighs 2.5 kg (5.51 lb) and comes with all necessary hardware for installation.

The bracket is designed to be used with two speakers, one mounted on each end.

1. SAFETY PRECAUTIONS
• Beforeinstallationoruse,besuretocarefullyread
all the instructions in this section for correct and
safeoperation.
• Besuretofollowalltheprecautionaryinstructions
in this section, which contain important warnings
and/orcautionsregardingsafety.
• After reading, keep this manual handy for future
reference.
Indicatesapotentiallyhazardoussituationwhich,
if mishandled, could result in death or serious
personalinjury.
WARNING
• Referallinstallationworktothedealerfromwhom
the speaker was purchased. Installation onto the
ceilingrequiresextensivetechnicalknowledgeand
experience.The speaker may falloff ifincorrectly
installed,resultinginpossiblepersonalinjury.
• Installtheunitonlyinalocationthatcanstructurally
supporttheweightofthespeakerandthemounting
bracket.Doingotherwisemayresultinthespeaker
falling down and causing personal injury and/or
propertydamage.
• Owing to the speaker's size and weight, be sure
thatatleasttwopersonsareavailabletoinstallthe
speaker. Failure todo so could result in personal
injury.
• Donotuseothermethodsthanspeciedtomount
thebracket.Extremeforceisappliedtothebracket
andthespeakercouldfalloff,possiblyresultingin
personalinjuries.
• Usesafetywireswheninstallingspeakers.Ifnot
used, personalinjurycouldresult if a speaker
shouldaccidentallyfall.
• Attachthesafetywiretothespeaker.Ifnotattached,
thespeakercouldfalloff,resultinginpersonalinjury.
• Use nuts and bolts that are appropriate for the
ceiling’sstructureandcomposition.Failuretodoso
maycausethespeakertofall,resultinginmaterial
damageandpossiblepersonalinjury.
• Tighten each nut and bolt securely. Ensure that
the bracket has no loose joints after installation
to prevent accidents that could result in personal
injury.
• UsetheHX-7B-WPorHX-7W-WPSpeakerSystem
in combination. Doing otherwise may cause the
speakertofalloff,resultinginpersonalinjury.
• Do not mount the speaker in locations exposed
to constant vibration. The rigging bracket can be
damagedbyexcessivevibration,potentiallycausing
the speakertofall, whichcouldresult in personal
injury.
• Avoidinstallingthespeakerinlocationsclosetothe
seashore or in indoor swimming facilities thatare
not well ventilated. In such locations, the bracket
maybevulnerabletocorrosion,eventuallyallowing
thespeakertofallresultinginpersonalinjury.
Indicatesapotentiallyhazardoussituationwhich,
ifmishandled,couldresultinmoderateorminor
personalinjury,and/orpropertydamage.
CAUTION
• Avoid touching the bracket's sharp metal edge to
preventinjury.
• Do not stand or sit on, nor hang down from the
bracketasthismaycausethespeakertofalldown
ordrop,resultinginpersonalinjuryand/orproperty
damage.
• Havethebracketcheckedperiodicallybytheshop
fromwhereitwaspurchased.Failuretodosomay
resultincorrosionordamagetothespeakerorits
riggingbracketthatcouldcausethespeakertofall,
possiblycausingpersonalinjury.
INSTALLATION MANUAL
SPEAkER RIGGING bRACkET HY-TM7b-WP
HY-TM7W-WP
ThankyouforpurchasingTOA’sSpeakerRiggingBracket.
Pleasecarefullyfollowtheinstructionsinthismanualtoensurelong,trouble-freeuseofyourequipment.
2. GENERAL DESCRIPTION
TheHY-TM7SeriesSpeakerRiggingBracketsareusedtohangtheHX-7B-WPorHX-7W-WPSpeakerSystem
directlyfromceilings,beamsorotherbuildingstructures,includingunderoutdooreaves.
3. NOTES ON INSTALLATION
• Observethefollowinginstructionswheninstallingthespeaker
system.
Failuretodosocouldadverselyaffecttheirintendedweather-
resistantcapability,leadingtomalfunction.
· Installthespeakersysteminlocationsnotexposeddirectlyto
rain,suchasundereaves.
· Allspeakermodulesmustpointdownwardfromthehorizontal.
• TwojoinedHX-7 SeriesSpeaker Systems cannotbe installed
withthisbracket.
4. INSTALLATION
Step 1. Mountthisbrackettoaceiling,beam,etc.usingthebolts.
Boltsandnutsformountingthebracketontheceilingorbeamarenot
supplied.
Use bolts and nuts that are appropriate for the ceiling’s or beam’s
structureandcomposition.Failuretodosomaycausethespeakerto
fall,resultinginmaterialdamageandpossiblepersonalinjury.
WARNING
[Mounting dimensions]
36
(1.42")
146.5 (5.77")
[Front] [Right side]
ø8.5 (0.33") (with M8 weld nut)
ø8.5 (0.33")
(with M8 weld nut)
ø8.5 (0.33")
(with M8 weld nut)
ø8.5(0.33")
(6 positions)*
353 (13.9")
60 (2.36")
100 (3.94")100 (3.94")
0
26
(1.02")
76
(2.99")
126
(4.96")
291
(11.46")
220
(8.66")
170
(6.69")
φ8.5 (0.33")*
Note: Left-side surface same.
Unit: mm
*TheseholesnotttedwithM8weldnuts.
[Vertical installation]
Horizontal
Step 2. Mountthespeakersystemtothisbracket.
Mountthespeakersystemvertically,asshowninthegure.
Fixthespeakertothemountingbracketatall3indicatedplaces.
2-1. Fixthisbrackettobothendsofthesideangleplateofthespeakerfront.
Usethesuppliedbolts(withspringandplainwashers)andspacers.
2-2. Fixthisbrackettothespeaker’srearbracket.
Fixtotherearbracket’sendmosthole.
Usethesuppliedbolt(withspringandplainwashers),J-spacer,andangenut.
Fordetails,refertotheprocedures(1)to(3)asshownbelow.
• Use safety wires when installing speakers. If not used, personal
injurycouldresultifaspeakershouldaccidentallyfall.
• Owingto the speaker's size and weight, besure that at leasttwo
personsareavailabletoinstalltheunit.
Failuretodosocouldresultinpersonalinjury.
• Tighten the bolts securely, as instructed below. Failure to follow
instructionspreciselycouldresultinafallingspeakerandpotential
personalinjury.
· Ensurethatallboltsaresecurelyinsertedasfarastheirthreadsgo,
thensecurelyfasteneachboltwithanut.
· Tighten all the bolts with the designated tightening torque. For
tightening,useaPhillipsscrewdriver,oropen-orbox-endwrench.
WARNING
This bracket
HX-7B-WP or HX-7W-WP
J-spacer
(accessory)
Rear bracket
(1) Lightly secure.
(3) Tighten firmly.
(2) Insert.
Flange nut
for M6 (accessory)
Hex head
bolt M6x30
(accessory)
Tightening
torque: 5 N·m
Spacer ø9.2 (0.36")
(accessory)
Hex head bolt
M6x12(accessory)
Side angle plate
Protection cover
Note
Remove the
protection covers
from the side
angle plates
before joining.
Tightening torque:
5 N·m
2-1
Note
Similarly, fix this bracket to the end of the
side angle plate on the opposite side.
2-2
This bracket
HX-7B-WP or HX-7W-WP
[Completed installation]
Step 3. Attachsafetywiresforprotectionagainstfalls.
Regardingtheattachingmethodofsafetywires,
refertotheoperatinginstructionssuppliedwith
HX-7Seriesspeakersystem.
Note
Aftertighteningthebolt,ensurethat
theJ-spacerisrmlyxed.
5. SPECIFICATIONS
ModelNo. HY-TM7B-WP HY-TM7W-WP
Finish Stainless steel, black, semi-gloss,
paint
Stainless steel, white, semi-gloss,
paint
Dimensions 433(w)x57(h)x295(d)mm(17.05"x2.24"x11.61")
Weight 2.5kg(5.51lb)
Note: Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.
Accessories
HexheadboltM6x12withspringandplainwashers... 2
HexheadboltM6x30withspringandplainwashers... 1
FlangenutforM6........................................................... 1
Spacerø9.2(0.36")........................................................ 2
J-spacer.......................................................................... 1
URL:http://www.toa.jp/
133-01-00045-00
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

TOA HY-TM7B-WP User manual

Category
AV equipment stands
Type
User manual
This manual is also suitable for

TOA HY-TM7B-WP is a speaker rigging bracket designed for use with TOA's HX-7B-WP or HX-7W-WP Speaker Systems. It allows for the safe and secure mounting of these speaker systems from ceilings, beams, or other building structures, including under outdoor eaves.

The bracket is made of stainless steel with a black, semi-gloss paint finish, and it has dimensions of 433 (w) x 57 (h) x 295 (d) mm (17.05" x 2.24" x 11.61"). It weighs 2.5 kg (5.51 lb) and comes with all necessary hardware for installation.

The bracket is designed to be used with two speakers, one mounted on each end.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI