Vermont Castings VCS6005 Operating instructions

Brand: Vermont Castings

Model: VCS6005

Category: Rack accessories

Type: Operating instructions

VCS6005 Assembly

Page 5

BQ128

grates knobs

2/05

Step 8: Side Burner Grates,

Side Burner Knobs

Materials Required:

Side Burner Grate (2)

Side Burner Knob (2)

Place side burner grates in proper position.

Attach knobs.

Step 9: Backlit Knobs

Materials Required:

Backlit Knob (7)

Attach to the console backlit knobs as shown.

Grates Side Burner

Knobs Side Burner

BQ129

attach knobs

2/05

Step 10: Attach Handle to Door

Materials Required:

Handle (3)

Secure the door handles (2) to the doors by insert-

ing two (2) screws (supplied with handles) through

the circular cutouts at the rear of the door panel and

into the handle.

Attach third handle to the pull out drawer above

the doors.

NOTE: Handles may not be exactly as shown de-

pending on your model.

BQ107

attach handles

12/04

VCS6005 Assembly

Page 6

Step 11: Grease Tray and Grease Cups

Materials Required:

Grease Cups (2)

Grease Tray Assembly (1)

A. Place grease cups in position into openings in

the upper base panel area. (Fig. 11a)

B. Place grease tray in position under the com-

bustion area. (Fig. 11b)

BQ130

grease cups

2/05

Grease Cup Openings

Grease Cups

BQ131

grease tray

2/05

Fig. 11a

See Detail A

Detail A

Slide

Fig. 11b

Step 12: Install Internal Components

Materials Required:

Sear Plates (6)

Cooking Grates (4)

Griddle Plate (1)

Warming Rack (1)

Refer to Figure 12 for proper locations.

Place the sear plates into the base unit ensuring

the edges with the “ﬁnger holes” face the grill

front. Position the griddle plate and the cooking

grates into the base with the ﬁnger holes facing

the front. Cooking grate may be turned over to

provide a ﬂat surface for delicate foods. Set the

warming rack into the two supports in the ends

of the rear lid.

BQ132

griddle plates

2/05

Cook Grate

Sear Plate

Warming Rack

Finger Holes

at Front

Griddle

Plate

Fig. 12

VCS6005 Assembly

Page 7

Step 13: Attach Stabilizer Bracket

Materials Required:

Stabilizer Bracket (2)

10-24 x 1/2” Long Black Bolt (4)

Attach the stabilizer brackets to the bottom

panel.

Secure with four (4) bolts.







Bolts

Stabilizers

Step 14: Install the LP Cylinder (LP Models Only)

Materials Required:

LP Gas Cylinder (Not included)

NOTE: Refer to the Userʼs Manual for the cylinder ﬁlling requirements, regulator attachments and leak test-

ing procedures, before lighting the grill.

Insert the Propane (LP) Cylinder into the hole provided into the bottom panel.

Secure cylinder with cylinder retainer (as shown below).

Connect the cylinder to the regulator.

BQ111

LP tank

12/04

BQ112

tank retainer

12/04

Step 15: Attach Utensil Hooks to Shelf

Materials Required:

(3) Utensil Hooks

Attach three (3) Utensil Hooks into the holes located

at the bottom of the shelf.

Attach to either side of grill.

A_3

BQ116

hooks

12/04

Hooks

VCS6005 Assembly

Step 16: Side Burner / Rotisserie Control Functions

Rear Burner

Front Burner

Rotisserie

Burner and

Side Burner

Igniter

Knob Controlling

Front Burner

Knob Controlling

Rear Burner

410 Admiral Blvd. * Mississauga, Ontario * Canada L5T 2N6

www.myownbbq.com * www.vermontcastings.com

phone: 1-800-227-8683

fax: 905-565-4690

Vermont Castings VCS6005 Operating instructions

Brand: Vermont Castings

Model: VCS6005

Category: Rack accessories

Type: Operating instructions

Download PDF

report

Vermont Castings VCS6005 Operating instructions

Vermont Castings VCS6005 Operating instructions

Related papers

Other documents