Schneider Electric PIR Motion Sensor Instruction Sheet

Brand: Schneider Electric

Model: PIR Motion Sensor

Type: Instruction Sheet

(1) (3)(2) (4)

(1) (2)

1.2 m

Side viewTop view

0 8 9

8 9

110°

0 9

Less sensitive to radial movementHighly sensitive to cross movement

(3)

(1)

L L’N N

Load

(2)

L L’N N L L’N N

Load

(3)

LL’NN Load

Staircase timer

Push

button

Ein

„

(1) (3)

(6)

(4)

Lux

(2)

ON AUTO OFF

(5)

(7) a. (7) b. (7) c.

Meter

Time

20 min 6 sec

Test

1S.

Finish

Start

Walk test

LED

AUTO ON OFF

(1) (2)

$ Operation

(1) Open up the knob cover:

slightly.

(2) Knob setting:

To adjust Time, Lux, Meter knobs refer to the

following steps and make sure the slide switch is

at the position “AUTO”.

(3) Lux knob setting

a. Setting Lux knob value at the position “ ”,

means sensor can work in the dark only.

b. Setting Lux knob value at the position “ ”,

means sensor can work at any light level.

c. Adjusting the Lux knob according to your desire.

(4) Time knob setting

(5) Meter knob setting

a. Setting Meter knob value at the position “-”,

performed.

b. Setting Meter knob value at the position

performed.

c. Adjusting the Meter knob according to your

desire in between the position “-” and “+”.

(6) Walk test

Note: It takes 30 secs for sensor to warm up

with LED and load turn on, then enters into

standby mode. The purpose of conducting a

walk test is to select a proper location to get the

best detection range. Set the slide switch at the

position “AUTO”, turn Meter knob to “+”, Time

knob to “test”, then conduct a walk test referring

to below steps:

• Install the sensor correctly, to make sure wiring is

connected correctly.

• Switch on the power.

• Walk from outside across to the detection pattern,

once the sensor is triggered, Led and load will all

turn on for 2 sec.

• Adjust Meter knob to targeted coverage.

• Repeat the above steps until it meets your needs.

• Pay attention to the walking direction while

proceeding the test.

• Use the Red LED behind the lens for indication.

Lux setting value is disabled.

(7) Manual switch function

a. AUTO: Set slide switch at the middle position

(AUTO), sensor is in auto operation mode. If time

knob is set between 6 sec and 20 min, LED will

turn on for 1 sec once the sensor is triggered.

b. ON: Set the slide switch leftward, “ON” mode is

activated, load will be permanent on with LED

c. OFF: Set the slide switch rightward, “OFF” mode

% Unmounting the sensor

(1) Insert a screwdriver between the cover frame

and the wall surface to remove the cover frame.

Then twist the screwdriver to disassemble the

cover frame from the sensor.

(2) Use the other hand to support and remove the

cover frame.

en PIR Motion Sensor

About this product

The PIR Motion Sensor (hereinafter referred to as

Sensor) is 110° wall mounted. It is ideally located in

as corridors, staircases, dining rooms, cellars, drawing

rooms, bedrooms, garages, etc. Additionally, it has the

following features:

• Suitable for a normal wall box for easy installation

and operation.

•

modes of function.

• Screw-in terminal block for easy and safe wire

connection.

• Replace two-way switch of staircase by PIR

Motion Sensor to make the operation fully

automatic.

• Energy saving: Built-in photocell allows automatic

operation at night and in daylight.

!Mounting the sensor

CAUTION

HAZARD OF EQUIPMENT DAMAGE

•

• Bulb burn of certain brands would cause high

inrush current which might damage the unit

permanently.

•

• Circuit breakers are recommended to be installed

upfront for safety precaution.

Failure to follow these instructions can result in

injury or equipment damage.

(1) Mount the wall box to the wall.

(2) Connect the wires to the sensor.

(3) Place the sensor on the wall box and secure it

using the screws on both sides.

(4) Assemble the cover frame on the sensor,

ensuring proper engagement by hearing a clear

“click.”

“ Choose a suitable location to install

(1) Detection coverage: It is recommended to install

the sensor at the height of 0.8 m to 1.5 m. At the

height of 1.2 m, the detection range is up to 9 m

frontward and 8 m sideward.

(2) Installation tips: Since the sensor is respondent

to temperature change, please avoid the

following conditions:

a. Directing the sensor towards the objects whose

monitors, etc.

b. Mounting the sensor near the heat sources,

such as heating vents, air conditioners, vents as

dryers, lights, etc.

c. Aiming the sensor towards the objects which

may be sway in the wind, such as curtains, tall

plants, miniature garden, etc.

(3) Pay attention to the walking direction during the

test.

§Wiring diagram

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION,

OR ARC FLASH

Safe electrical installation must be carried out only

by skilled professionals. Skilled professionals must

prove profound knowledge in the following areas:

• Connecting to installation networks.

• Connecting several electrical devices.

• Laying electric cables.

• Safety standards, local wiring rules and

regulations.

Failure to follow these instructions will result in

death or serious injury.

(1) Normal Operation

(2) Two sensors control one load

(3) One sensor controls staircase timer (Set time

knob to 1s. )

Time: Adjustable from 6 sec to 20 min. Set the

time knob between 6 sec to 20 min. LED will turn

on for 1 sec once the sensor is triggered.

Test: Walk test operation. Set the Time knob at

“test”, once the sensor is triggered, both of load

next trigger should be 2 sec interval. Lux setting

value is disabled.

1S.

: Short impulse for staircase timer switch

1S.

“ ”, once the sensor is triggered, both of load

next trigger should be 9 sec interval.

Troubleshooting

Problem Possible cause Suggested solution

LED does

not turn on.

Power is not

switched on.

Switch on the power.

Wire is connected

incorrectly.

Refer to wiring

diagrams and

connect wiring

correspondingly.

Load does

not turn on.

Wire is connected

incorrectly.

Refer to wiring

diagrams and

connect wiring

correspondingly.

Defective load.Replace the defective

load with a new one.

Meter setting is too

short.

Setting Meter knob

to “+”.

The slide switch is

at “OFF”.

Adjust slide switch at

“AUTO” or “ON”.

Load does Time setting is

too long, sensor

is continuously

triggered.

Set time in test mode,

check whether the

sensor is nuisance

triggered.

Sensor is nuisance

triggering.

Keep away from

the detection zone

to avoid activating

sensor.

Wire is connected

incorrectly.

Please check if load is

connected correctly.

Nuisance

triggering

There are heat

sources or any

objects which may

be swayed in the

wind within the

Avoid aiming the sen-

sor toward any heat

sources, such as air

conditioners, electric

fans, heaters, or

objects. Make sure

there are no swaying

objects within the

Note:

• Do not attempt to open or repair the unit without

• The following conditions may cause lower

sensitivity:

• In very hot days, the sensitivity may be less

since high ambient temperature is close to body

temperature.

• In very cold days when heavy clothing is dressed,

especially the facial area is covered, very little

heat will be emitted from the body causing the unit

to be less sensitivity.

• Cleaning: Wipe with dry cloth only. Soap or rough

cloth may damage the sensor lens.

Care

1. Use a soft damp cloth/tissue to remove dust or dirt.

cleaning.

3. Do not use caustic cleaning agents.

Technical data

Rated Voltage 230 Vac

Detection Angle Up to 110°

Detection Range About 9 m for frontward, 8 m each

for sideward at the height of 1.2 m

(20 to 25 °C)

Mounting Height 0.8 to 1.5 m (optimal mounting

height: 1.2 m)

Lux Adjustment Adjustable from “ ” (about 5 Lux)

to “☼” (∞)

“test” & “ 1S ”

Meter Adjustable for detection zones

Manual Switch (3 modes) Manual on permanently / AUTO / OFF

Environmental Protection IP40

Operating Temperature 0 to 45 °C

Dimensions 98 x 101 x 40.70 mm

Types of load

Incandescent Lamp 2000 W maximum

AC Halogen Lamp 1000 W maximum

LV Halogen Lamp 1000 VA maximum (electronics

and traditional)

Fluorescent Lamp 900 VA maximum / 100 µF

(compensated)

Energy saving Lamp

(include CFL and PL Lamp)

600 VA maximum

Schneider Electric Industries SAS

If you have technical questions, please contact the

Customer Care Centre.

Customer Care: 1800 103 0011

Email: [email protected]

Mktd. by: Schneider Electric India Pvt. Ltd.,

C56, Mayapuri Industrial Area, Phase II,

New Delhi - 110064, India.

Mfg. by: Schneider Electric India Pvt. Ltd.,

A9/10, Nimblak Road, MIDC, Nagapur,

Ahmednagar 414111, Maharashtra, India

UNSPIR_xx PIR Motion Sensor

MFR3778401-03 07/23

Schneider Electric PIR Motion Sensor Instruction Sheet

Schneider Electric PIR Motion Sensor Instruction Sheet

Schneider Electric PIR Motion Sensor Instruction Sheet

Other documents