Konica Minolta Df-601 Installation guide

Brand: Konica Minolta

Model: Df-601

Type: Installation guide

Konica Minolta Df-601 is an automatic document feeder that can be used to scan, copy, and fax documents. It has a capacity of up to 50 sheets of paper and can handle a variety of document sizes, including A4, letter, and legal. The Df-601 also features a number of adjustable settings, including the document feeding width, skew, and reference position. This allows you to customize the feeder to meet your specific needs.

The Df-601 is easy to install and use. Simply follow the instructions in the user manual and you'll be up and running in no time. Once installed, the Df-601 can be used to scan, copy, and fax documents directly from your computer.

E-1

DF-601 Automatic Document Feeder

4582-7701-03

INSTALLATION MANUAL

Applied Machine: C250

COLOR MFP 25 ppm

for Product Code 4038

I. Accessory parts II. Installation procedures

1. Turn off the machine and unplug the power cord

from the power outlet.

2. Remove the two hinge covers at two places

(one screw each).

Note:

When the spacer is mounted, remove the spacer.

3. Screw the shoulder screws furnished with the

Automatic Document Feeder into the holes in the

rear (one screw each).

No. Name Shape Q’ty

1. Shoulder screw

2. Mounting screw

3. Chart

4. Installation

Manual

set

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting your head in the wrapper involves

danger of suffocation.

4582U010AA

4582U011AA

4980IXC019DA

4582IXC002DB

Spacer

4582IXC001DA

E-2

4. Place the Automatic Document Feeder in posi-

tion.

Note:

When installing the Automatic Document Feeder,

hold onto the upper and lower ends of the Auto-

matic Document Feeder in the vertical position as

shown on the left.

5. Using the two mounting screws furnished with

the Automatic Document Feeder, tighten the

hinges to secure the Automatic Document

Feeder in position.

Note:

Check that the shoulder screws are fully tight-

ened.

6. Remove the plastic bag of the hookup cable.

7. Connect the hookup cable to the machine.

III. Adjusting the Document Feeding Tray

Width

1. Plug the power cord into the power outlet and

turn on the machine.

2. Widen the width across the edge guides by slid-

ing them to their maximum width.

3. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the Service Manual.)

4. Touch “ADF.”

5. Touch “Original Tray Width.”

C4652U012AA

4582U001AD

4582U018AA

4582U013AA

4037IXE295DA

4582IXE508DA

E-3

6. Touch “Max. Width” and then press the Start key.

Check that “Adjustment Result” is “OK.”

7. Narrow the width across the edge guides by slid-

ing them to their minimum width.

8. Touch “Min. Width” and then press the Start key.

Check that “Adjustment Result” is “OK.”

9. Touch “END.”

10.Touch “Exit” on the Service Mode screen.

IV. Checking and Adjusting Document

Skew

1. Place the chart in the document feeding tray (with

the side having an arrow facing up).

2. Set up the following functions:

• Select the tray in which A4 crosswise or Letter

crosswise paper is loaded.

• 1-sided original 1-side copy

3. Press the Start key.

4. Check in which direction, A or B, the image tilts

on the copy fed out of the machine.

Specifications: Tilt 3 mm max.

* If the image tilts more than the specifications, per-

form the following steps to make the adjustment.

4582IXE509DA

4582U014AA

4582IXE510DA

4582U003AA

▲

4582U006AC

E-4

5. Loosen the two front screws on the right hinge.

If the gap A is wider than gap B, move the Auto-

matic Document Feeder toward the front.

If the gap B is wider than gap A, move the Auto-

matic Document Feeder toward the rear.

Note:

Do not move the Automatic Document Feeder to

the frontmost or leftmost position.

6. Tighten the two screws.

7. Make the copy and check again.

V. Checking and Adjusting the Document

Feeding Tray Reference Position

1. Place the chart in the document feeding tray

(with the side having an arrow facing up).

2. Set up the following functions:

• Select the tray in which A4 crosswise or Letter

crosswise paper is loaded.

• 1-sided original 1-side copy

3. Press the Start key.

4. Fold the copy in half.

5. With reference to the crease, check to see if the

arrow is on the side of A or B.

Specifications: ± 2 mm from the center

* If the deviation falls outside the specified range,

use the following procedure to make an adjust-

ment.

4582U007AC

4582U003AA

▲

E-5

6. Loosen the screw (two on the front side and three

on the backside) on the document feeding tray.

If the crease deviates on the side of A, move the

tray to the front.

If the crease deviates on the side of B, move the

tray to the rear.

7. Tighten the five screws.

8. Make the copy and check again.

VI. Adjusting the Document Stop Position

1. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the Service Manual.)

2. Touch “ADF.”

3. Touch “Auto Stop Position Adjustment.”

4. Touch “Sub Scanning Direction 1-Side.”

4582U005AC 4037IXE295DA

4582IXE508DA

4582IXE003DA

E-6

5. Place the chart in the document feeding tray

(with the side having an arrow facing up).

6. Press the Start key.

7. Make sure that “Adjustment Result” is “OK.”

Then, touch “SET.”

8. Touch “Sub Scanning Direction 2-Side.”

9. Place the chart in the document feeding tray.

Note:

Make sure that the blank surface of the chart

faces up.

10.Press the Start key.

11.Check that “Adjustment Result” is “OK” and then

touch “SET.”

12.Touch “Main Scanning Direction.”

13.Place the chart in the document feeding tray

(with the side having an arrow facing up).

14.Press the Start key.

15.Check that “Adjustment Result” is “OK” and then

touch “SET.”

16.Touch “END.”

17.Touch “Exit” on the Service Mode screen.

18.Turn OFF and ON the Main Power Switch.

Note:

When displayed the Service Mode screen, be

sure to turn off the main power after exiting the

Service Mode screen and wait for 10 seconds or

more before turning on.

VII. Fixing the Stoppers

Loosen the stopper screws (two each on the right

and left). Then, with the stoppers raised, tighten the

screws.

4582U003AA

4582IXE512DA

4582IXE513DA

4582IXE514DA

4582U009AB

4582U008AB

Konica Minolta Df-601 Installation guide

Konica Minolta Df-601 Installation guide

Konica Minolta Df-601 Installation guide

Related papers

Other documents