Astria Fireplaces ELDV-35/40/45 Instruction Sheet

Type
Instruction Sheet

This manual is also suitable for

Astria Fireplaces ELDV-35/40/45 are designed to enhance the beauty of your fireplace and create a barrier to prevent direct contact with the hot glass.

These free-standing screens are easy to assemble and can be used as a freestanding screen placed in front of the fireplace or secured to the front of the appliance.

The screens are height adjustable and come with adjustable brackets to fit various facing thicknesses.

The attached chain helps to prevent the screen from tipping over, and the decorative design adds a touch of elegance to any room.

Astria Fireplaces ELDV-35/40/45 are designed to enhance the beauty of your fireplace and create a barrier to prevent direct contact with the hot glass.

These free-standing screens are easy to assemble and can be used as a freestanding screen placed in front of the fireplace or secured to the front of the appliance.

The screens are height adjustable and come with adjustable brackets to fit various facing thicknesses.

The attached chain helps to prevent the screen from tipping over, and the decorative design adds a touch of elegance to any room.

P/N 750218M
REV. C 01/2014
HEARTH PRODUCTS
KITS AND ACCESSORIES
1
Cat.
No.
Model Description Model Series
H4688 DASK-DV35 Dual Arch Screen Kit - DV35 ELDV35 & SYM35
H4689 DASK-DV40 Dual Arch Screen Kit - DV40 ELDV40 & SYM40
H4690 DASK-DV45 Dual Arch Screen Kit - DV45 ELDV45 & SYM45
Table 1 - Arch Screen Panel Kits
DUAL ARCH SCREEN PANEL KITS
INSTALLATION INSTRUCTIONS FOR OPTIONAL ARCH
SCREEN PANEL KITS FOR USE WITH GAS FIREPLACES
FIREPLACE MODELS ELDV35, ELDV40, ELDV45, SYM35, SYM40 AND SYM45
Figure 1 - Kit Contents
Models
DASK-DV40 & DASK-DV45
Model
DASK-DV35
KIT CONTENTS (See Figure 1)
1 ea. Screen Assembly (1)
2 ea. Bottom Legs (2)
2 ea. Long Screws (3)
2 ea. Medium Screws (4)
4 ea. Short Screws (5)
2 ea. Long Spacers (6)
4 ea. Sliding Bracket A (8)
4 ea. Sliding Bracket B (9)
6 ea. Nuts (10)
2 ea. L-Brackets (11)
4 ea. Wing Nuts (12)
1 ea. Instruction Sheet
REQUIRED TOOLS
7/16” End Wrench
7/32” Allen Wrench
1
11
5
10
9
12
812
910
85
12 910
85
910
11
12
5
8
10
7
6
2
4
3
7
6
2
4
310
750,218M REV. NC
3/2005
LENNOX HEARTH PRODUCTS
KITS AND ACCESSORIES
TOOLS REQUIRED
7/16” Nutdriver
GENERAL INFORMATION
These optional decorative rescreen panels are designed to enhance the
beauty of the rpleplace. If you encounter any problems, need clarifi cation
of these instructions or are not qualifi ed to properly install this kit, contact
you local distributor or dealer.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
1
Cat. No.Model DescriptionModel Series
H4688DASK-DV35Dual Arch Screen Kit - DV35 ELDV35
H4690DASK-DV45Dual Arch Screen Kit - DV45 ELDV45
Table 1 - Arch Screen Panel Kits
Item#QuantityDescription
11 ea.Screen Assembly
22 ea.Bottom Legs
32 ea.Long Screws
42 ea.Medium Screws
62 ea.Long Spacers
84 ea.Sliding Bracket A
94 ea.Sliding Bracket B
10 4 ea.Nuts
11 2 ea.L- brackets
12 4 ea.Wing Nuts
13 1 ea.Instruction Sheet
Table 2
- Kit Contents
(item numbers correspond to Figure 1)
DUEL ARCH SCREEN PANEL KITS
ELDV-35/40/45 SERIES
INSTALLATION INSTRUCTIONS FOR OPTIONAL ARCH SCREEN PANEL KITS
FOR USE WITH ELDV35, ELDV40 AND ELDV45 SERIES GAS FIREPLACES
WARNINGS
Hot! Do not touch!
The decorative screen doors
become hot during operation
and will retain
heat for a while after shutting off the appliance
.
Severe burns may result. Carefully supervise
children in the same room as appliance.
• These decorative screen doors are NOT heat guards
• INSTALL ONLY WHEN THE FIREPLACE IS OFF AND COLD!
1
11
5
8
9
12
8
12
9
10
85
12 910
85
910
11
12
5
8
8
7
6
2
4
3
7
6
2
4
310
Figure 1
Kit Contents
(see Table 2)
INSTALLATION INSTRUCTIONS
Step 1. Assemble componets to screen assembly as shown in Figure 2.
Figure 2 - Assemble Components to Screen Assembly
Refer to Figure 1 for com-
ponent identication
Using an 7/16” nutdriv-
er, loosely assemble
the components to the
screen assembly as
shown in Figure 1 &
Figure 2 (do not tighten
nuts yet).
13
GENERAL INFORMATION
These decorative, free-standing screens are designed to enhance the beauty of
the fireplace and create a barrier to prevent direct contact with the hot glass.
The attached chain is provided to secure the screen to the fireplace, to help
prevent the screen from tipping over.
If you encounter any problems, need clarification of these instructions or are
not qualified to properly install this kit, contact you local distributor or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION INSTRUCTIONS
AND CARE AND OPERATION MANUALS PROVIDED WITH THE APPLIANCE
APPLY TO THESE INSTRUCTIONS.
TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL BEFORE
PROCEEDING.
WARNING
Hot! Do not touch! These decorative screen
panels are NOT heat guards.
The glass behind
the screens will be hot during operation
and
will retain heat for a while after shutting off the
appliance
.
Severe burns may result. Carefully
supervise children in the same room as appliance.
As with any similar heating appliance, surfaces of the
frame, the door and appliance can become very hot.
Printed in U.S.A. © 2006 IHP LLC
P/N 750218M REV. C 01/2014
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products. Consult your local distributor
for fireplace code information.
2
Locking tab
pointing up
Rotate tab 90º into corresponding slot on
fireplace front (as shown in picture B).
Correct locking position
of tab into slot.
A
B
C
Sliding brackets
are designed
to adjust for
various facing
thicknesses.
1. Slightly tighten the 2 nuts on right side of screen which secure sliding brackets to screens
(loose enough so brackets can be rotated in instruction number 3 below). Snugly tighten the
2 nuts on the left side of the screen (with brackets rotated in the locking position - B).
2. Adjust the four sliding bracket as-
semblies to the thickness needed for
a near flush fit to facing, then tighten
wing nuts.
3. Rotate the right side tabs from position
A to position B to lock in place.
NOTE: Tabs should fit into slots as shown in
Figure 3A. Adjust alignment if necessary.
Figure 3B - Assemble Screen Assembly to Fireplace
Figure 4
Figure 3A - Inside View of Adjustable Brackets
Screen Fireplace
Adjustable
Brackets
Wing Nut
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Tabs lock
into slots on
fireplace
INSTALLATION INSTRUCTIONS
Screen Panel Assembly Instructions
Step 1. Using an 7/32” Allen Wrench and 7/16” End Wrench, loosely as-
semble the parts as shown in Figure 1 and Figure 2 (do not tighten
yet). Note: If the screen panel is to be used as a freestanding screen
only (not attached to fireplace), do NOT use the sliding brackets
with screws and wing nuts (circled in Figure 2). If the screen panel
is to be secured to the front of the fireplace these parts should be
assembled to the screen panel (ref. Step 4).
Step 2. Adjust the L-Bracket to height needed for this installation (slot allows
up to 1 inch vertical adjustment). When you are satisfied that the
screen will stand stable in front of the fireplace, then tighten the
nuts on both sides.
Step 3. The assembled screen is ready to be used as a freestanding screen
placed in front of the fireplace when in use (in a close proximity to the
glass door) or if it is desired it can be assembled to the face of the ap-
pliance per instructons in Step 4. **Read IMPORTANT note above**
Figure 2
Refer to Figure 1 for
component identification
Using an 7/16” End Wrench
and 7/32” Allen Wrench,
assemble components to
the screen assembly as
shown.
Assemble Components
to Screen Assembly
Install Screen Panel onto Fireplace Front (optional)
Step 4. (optional) Secure the screen assembly to fireplace face - Adjust the
sliding brackets to the thickness needed for the screen to fit nearly
flush with the fireplace front & finish facing. Rotate tabs on sliding
brackets to lock in place per instructions in Figures 3a, 3b & 4.
IMPORTANT
To minimize possible exposure to hot surfaces, it is strongly
recommended that the screen assembly is secured to the
fireplace front if small children are present in the home
(see Step 4).
Completed
Installation
These components will not
be used if the screen panel
is to be used as a free-
standing screen only (not
attached to fireplace).
Innovative Hearth Products LLC
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
  • Page 1 1
  • Page 2 2

Astria Fireplaces ELDV-35/40/45 Instruction Sheet

Type
Instruction Sheet
This manual is also suitable for

Astria Fireplaces ELDV-35/40/45 are designed to enhance the beauty of your fireplace and create a barrier to prevent direct contact with the hot glass.

These free-standing screens are easy to assemble and can be used as a freestanding screen placed in front of the fireplace or secured to the front of the appliance.

The screens are height adjustable and come with adjustable brackets to fit various facing thicknesses.

The attached chain helps to prevent the screen from tipping over, and the decorative design adds a touch of elegance to any room.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI