Sportop E-8000P Owner's manual

Brand: Sportop

Model: E-8000P

Type: Owner's manual

Sportop E-8000P is an elliptical trainer designed to provide a full-body workout in the comfort of your home. With its adjustable resistance levels, you can customize your workout intensity for a challenging and effective cardio session. Track your progress with the LCD monitor that displays workout data such as time, distance, calories burned, and pulse. Choose from various training programs, including manual, preset, and customized options, to keep your workouts engaging and motivating.

MODEL:E 8000P

Owner's Operating Manual ENGLISH

ELLIPTICAL TRAINER

- 1 -

J1-L

F1-L

F2-R

J1-R

- 2 -

- 3 -

ASSEMBLY FOR REAR STABILIZER

Attach the Rear Stabilizer (C)(the Rear

Stabilizer will have wheels) to the

bracket at the back of the Main

Frame (A) Use two bolts (L1),

two Arc Washers (L2) and

two Nuts (L3.)

ASSEMBLY FOR FRONT STABILIER

Before you attach the Front Stabilizer(D)

to the brackets on the Main Frame (A)

you will need to put two bolts (L6)

and two washers (L7) under the Front

Stabilizer (D.) Then slide it under

the main frame(A)putting the bolts into

the underside of the pre-drilled holes of

the bracket. Once firmly through the holes

secure it with two washers (L8)

and two bolts (L3.) You

will have to hold onto

the bolt (L6) from the

bottom while

securing the

nuts (L3.)

Then secure the rest of the Front

Stabilizer (C) to the Main Frame (A)

with two bolts (L4) and two

washers (L5) these bolts will be

threaded directly into the Frame

and will not need any nuts.

- 4 -

B11

B12

B11

ASSEMBLY FOR MONITOR

Attach the cable wires from the Computer (E) to

the Sensor Wire (B11) and to the Cable Wire (B12.)

Once attached place the Computer on the fixing

plate and scure it wity the screw(E2).

ASSEMBLY FOR CENTRAL SUPPORT TUBE

Connect the Cable (A7) from the Main Frame(A) to the Cable (B11) coming out of the Central

Support Tube(B.) Once they are connected firmly, insert the Central Support Tube (B) into the

Main Frame (A.) Please make sure when attaching the two ends of the tube together that cables

are not pinched. Then use six bolts (L9) and six washers (L5) to secure in place.

- 5 -

J1-R

J11

ASSEMBLY FOR PEDAL SUPORT

Start with the right side and take the Pedal Support

Tube (J1-R) and pull up the connected tube (J11)

into the straight position. Once in the upright

position attach to the Connected Tube (K) making

sure firmly clicking in place. Repeat steps above

for the left side.

Once both sides of the lower and upper connected tube (K & J11) are attached to the pedal support

tube (J1-R.) It is now time to attach the upper portion of the connected tube (K) into the connected

tube (B2.) Then position the front moving wheels of the pedal support tube (J1-R) on the concave

of the front stabilizer (D). Once this is securely in place use 1 bolt (L10) there will be a series of five

holes for screws or bolts on the connected tube (B2) you must put bolt (L10) into the second from the

bottom (see picture 3.)

- 6 -

ASSEMBLY FOR PEDAL SUPORT TUBE

Slide the left side of the pedal support tube (J1-L)

into the rear hole on the main frame (A.) Attach

using the nut (L11.) Repeat the process on the

right side.

KEEP THE MACHINE STABLE

You can also use the adjustable end cap (D3-2)

to adjust for uneven or unlevel floors.

- 7 -

J1-R L13

L12

H2-R

H2-L

L12

ASSEMBLY FOR SIDE PEDAL JOINT COVERS

Attach the right and left side of the Pedal Joint

Cover (H2-R & H2-L) onto the Pedal Support

Tube (J1-R), secure using four bolts (L12)

ASSEMBLY FOR PEDALS

There are three positions to place the pedals. Starting with the right pedal (H3-R) on the Pedal

Support Tube (J1-R) and using washers (L8) and two Star Knobs (L13) attach firmly to one of

the positions on the Pedal Support Tube (J1-R.) Repeat the process above for the left side.

- 8 -

F2-R

F2-R F1-L

L14

B12

F2-R

F1-L

F7 B12

L14

ASSEMBLY FOR FRONT HANDLEBAR

Step1. Connect sensor wires(F7) and sensor wires(B12)

Step2. Insert the front handlebar(F1-L & F2-R)

into the central support tube.

Step 3.Twist and connect the

front handlebar (F1-L & F2-R)

as shown on (Figure 8-2).

StEP 4. Secure the front handlebar by bolts(L14)

as shown on (Figure 7-1).

And one screw(F4) as shown on

(Figure 7-3).

- 9 -

L17

H6 L15

L15

G1-L

L16

H5-L

H5-R

G1-R

ASSEMBLY FOR SIDE HANDLEBAR

Slide side handlebar(G1-L & G1-R) into connect tube and secure it by bolts(L15).

ASSEMBLY FOR WATTER BOTTLE HOUSING

Step 1. Assembly the bottle housing(H4) with the central support tube and

secure it by screw(L17).

Step 2. Assembly the decortation bottle housing (H5-L & H5-R) with the bottle housing

and secure it by screws(L16).

Then, You can put the water bottle on the bottle housing.

- 10 -

H1-FRONT

L16

H1-BACK

ASSEMBLY FOR SIDE HANDLEBAR JOINT COVER

Starting on the right side connect the

front of the Handlebar Joint Covers (H1-Front) to the

back of the Handlebar Joint Covers (H1-Back) using two screws (L16). Repeat the steps above for

the left hand side of the Handlebar Joint Covers (H1-Front & Back).

ASSEMBLY FOR ADAPTOR

On the Main Frame (A) there will be a female receptacle for an A/C adaptor. Plug in theAdaptor (E3)

to the female receptacle and plug the other end into your

electricity outlet. This will keep your batteries from running down too quickly.

- 11 -

HOW TO MOVE THE MACHINE

Stand at the front of the machine and lift it up until the weight of the machine is transferred to the

transport wheel (located on the Rear Stabilizer (C.) Now the machine can be rolled to a new location

if necessary.

- 12 -

A6-3

- 13 -

PARTS LIST

P/N DESCRIPTION Q'TY

A1 MAIN FRAME 1 B3 BUSHING 2 H3-R PEDAL (R) 1

A2-1 PULLEY AXLE 1 B4 BEARING 4 H4 WATER BOTTLE HOUSING

BACK COVER(L)

BACK COVER(R)

A2-2 NUT 4 B5 BEARING HOUSING 2 H5(L) 1

A2-3 BELT PULLEY 1 B6 BEARING HOUSING 2 H5(R) 1

A2-4 HEXAGON WASER 4 B7 FLAT WASHER 2 H6 WATER BOTTLE 1

A2-5 BEARING 2 B8 SPRING WASHER 2 J1-L PEDAL TUBE (L) 1

A2-6 C-CLIP 1 B9 HEXAGON WASHER 2 J1-R PEDAL TUBE (R) 1

A3 HEXAGON WASHER

2 B10 SHAFT 1 J2 HEXAGON SCREW 4

A4-1 PEDAL SUPPORT 2 B11 CABEL (MIDDLE) 1 J3 CLIP 4

A4-2 ARC PLATE 2 B12 HAND PULSE SENSOR 2 J4 BEARING 4

A4-3 SCREW 4 C1 REAR STABILIZER 1 J5 PIPE 2

A4-4 FLAT WASHER 4 C2 END CAP 2 J6 PU WHEEL 2

A4-5 CROSS SCREW 16 C3 TRANSPORTATION 2 J7 NYLON NUT 4

A5 DC CORD 1 C4 WASHER SCREW 4 J8 NYLON BUSHING 4

A6-1 MAGNETIC 1 D1 FRONT STABILIZER 1 J9 BEARING 2

A6-2 SHAFT 1 D2 ALUMINUM SLIDER 2 J10 SCREW 4

A6-3 BEARING 2 D3-1 ADJUSTED END-CAP 4 J11 CONNECT PIPE 2

A6-4 FLAT WASHER 2 D3-2 ADJUSTED-WHEEL 4 J12 PLSATIC BUSHING 4

A6-5 NUT 2 D3-3 ADJUSTED END-CAP 4 J13 SHAFT FOR PEDAL 2

A6-6 MAGNETIC 1 D4 CROSS SCREW 4 J14 BEARING 4

A6-7 SCREW 2 E1 MONOTIR 1 J15 TAPER BUSHING 2

A7 MOTOR SET 1 E2 SCREW 4 J16 FLAT WASHER 2

A8 CROSS WASHER 3 F1 FRONT HANDLE BAR (L)

1 J17 DECORTATION COVER 2

A9-1 TENSION PULLEY 1 F2 FRONT HANDLE BAR(R)

1 J18 SCREW 2

A9-2 FLAT WASHER 2 F3 U-BRACKET 1 J19 END CAP 2

A9-3 HEAXGON WASHER

1 F4 CROSS SCREW 2 K CONNECT PIPE 2

A9-4 BEARING 2 F5 SPONGE 2 L1 SCREW (3/8"x89mm) 2

A9-5 C-CLIP 1 F6 SPONGE 2 L2 ARC WASHER (3/8") 2

A10 SPRING 1 F7 HAND PUSLE SENSOR 2 L3 BOLT (3/8") 4

A11 CHAIN CVOER(L) 1 F8 4 L4 HEXAGON 4

A12 CHAIN COVER(R) 1 F9 2 L5 FLAT WASHER(3/8") 8

A13 CICLE PLATE 2 F10 SENSO

SPACER

SENSOR CHIP

R HOUSHING 2 L6 HEXAGON 2

A14 DECORTATION 2 F11 SENSOR HOUSHING 2 L7 FLAT 2

A15 SIDE COVER 2 F12 CLIP 4 L8 FLAT 4

A16 CHROMED SCREW

6 G1-L SIDE HANDLE BAR (L)

1 L9 HEXAGON 6

A17 HEXAGON SCREW 6 G1-R SIDE HANDLE BAR

(

)

1 L10 HEXAGON 2

A18 TENSION CABLE 1 G2 SPONGE 2 L11 NYLON NUT(3/8") 2

A19 BELT 1 G3 ROUND END CAP 2 L12 CROSS 8

A20 MAGNET 1 H1-F DECORTATION COVER 2 L13 KNOB (M8x35mm) 4

A21 SENSOR HOUSING

1 H1-B DECORTATION COVER 2 L14 HEXAGON 2

A22 SCREW 1 H2-L PEDAL JOINT COVER (L)

2 L15 HEXAGON 4

B1 CENTRAL SUPPOR

1 H2-R PEDAL JOINT COVER(R)

2 L16 CROSS SCREW 8

B2 CONNECT TUBE 2 H3-L PEDAL(L) 1 L17 CROSS 1

- 12 -

EXERCISE

COMPUTER

Monitor instruction manual

1. Plug the power supply (AC adaptor).

2. The monitor displays all segments for 2 seconds. [If you press RESET button for over 2 seconds, the

monitor will display all segments for 2 seconds for a new start.]

3. Press UP or DOWN to select training mode in MANUAL, PROGRAM(P1~P12),USER,TARGET.H.R.,

and press MODE to confirm setting.

4. Different training mode :

MANUAL-

1. Once you select MANUAL training mode, the LED bar below monitor display will light up to show

your current level position. You may increase or decrease training level by pressing UP or DOWN.

2. Press START/STOP to start training in Manual mode.(STOP symbol disappear from the monitor)

3. Press UP/DOWN/MODE to set target function datas of Time, Distance, Calories, Watt, and Pulse.

Each preset function (except Watt and Pulse) will count down from preset target as soon as training

starts.

4. You may adjust training resistance level (1~16) by pressing UP/DOWN during training. (except the

Watt datas has been preset)

[

Preset Watt datas for training] - If you have preset Watt datas, the training resistance level will be

adjusted automatically according to the training speed and RPM. If you see the symbol ϰ on the

monitor, it means your training speed is slow that the resistance level will be increased automatically

to maintain the preset watt. If you see the symbol ϧon the monitor, it means the speed is fast that

the resistance will be decreased automatically to maintain the preset watt. If you see the symbol ---

ϰon the monitor, it means your current speed is too slow and the resistance has been achieved to

the maxium level. At the moment, the monitor alarms "bi-b-bi" per second to remind you increasing

training speed. If you maintain same training speed for 1 minute, the monitor will alarm "bi-bi-bi-bi-

bi-bi" (per second) for 30 seconds and stop the system automatically [ The resistance level will be

- 13 -

droped to level 1 at the moment] as a proection implement. If you see the symbol --- and ϧ on the

monitor, it means your current speed is too fast and the resistance has been droped to the minium

level. At the moment, the monitor alarms "bi-b-bi" per second to remind you decreasing training

speed. If you maintain same training speed for 1 minute, the monitor will alarm "bi-bi-bi-bi-bi-bi" (

per second) for 30 seconds and stop the system automatically [ The resistance level will be dropped

level 1 at the moment] as a proection implement.

5. The monitor will alarm "bi-bi-bi" to remind you and stop as soon as one of each preset function target

has count down to zero.

PROGRAM

1. Once you select Program training mode, the LED bar below monitor display will light up to show your

current level position. You may increase or decrease training level by pressing UP/DOWN.

2. Press START/STOP to start training in Program mode.(STOP symbol disappear from the monitor)

3. Press UP/DOWN/MODE to select preferred training program profiles from P1 to P12.

4. Press UP/DOWN to adjust resistance level of the profile from level 1 to level 16. (You may adjust

training resistance level by pressing UP/DOWN buttons during training )

5. Press UP/DOWN/MODE to set target function datas of Time, Distance, Calories, and Pulse. Each

preset function will count down when the training starts.(Except Pulse)

6. Press START/STOP to start your training with PROGRAM mode.

7. The monitor will alarm "bi-bi-bi" to remind you and stop as soon as one of each preset function target

has count down to zero.(Except Pulse)

USER

1. Once you select User training mode, the LED bar below monitor display will light up to show your

current level position. You may adjust increas or decrease training level by pressing UP/DOWN.

2. Press UP/DOWN/MODE to preset your own Profiles for training. You may quit profile setting mode

by pressing MODE button for over 2 seconds.

3. Press UP/DOWN/MODE to set target function datas of Time, Distance, Calories, and Pulse. Each

preset function will count down when the training starts. (Except Pulse)

4. Press START/STOP to start your training with USER mode.

5. During training, you may press UP/DOWN to adjust resistance level.

6. The monitor will alarm "bi-bi-bi" to remind you and stop as soon as one of each preset function target

has count down to zero.(Except Pulse)

TARGET H. R.

1. When you select User training mode, the LED bar below monitor display will light up to show your

current level position. You may adjust increas or decrease training level by pressing UP/DOWN.

2. Once you select TARGET H.R. for training, the monitor requests you to input the AGE. Press UP/

DOWN/MODE to set age. This data is the key point for the proper target heart rate datas calculation

by the monitor.

3. Press UP/DOWN/MODE to select different percentage of target heart rate figures you would like to

achieve for training. There are 55%, 75%, 90% for selection, or you may input manually a target heart

- 14 -

heart rate figures for training.

3-1 The training resistance level is not available to be adjusted by buttons operation if you are training

in TARGET H.R. mode.

3-2 The resistance level will be auto adjusted by the monitor according to your actual heart rate figure.

If your current heart rate figures is under preset, the resistance level will be increased 1 level per

30 seconds till level 16 or the target heart rate figures is achieved. If your current heart rate figure

is exceed preset target figures, the resistance level will be decreased on level immediately. The

resistance level will be keeping decreased by one level per 15 seconds till level one. If your

current heart rate figure is still exceed the target when the resistance level is droped to level one

for 30 seconds, the monitor will stop and keep alarm to remind you.

4. Press UP/DOWN/MODE to set target function datas of Time, Distance, Calories. Each preset function

will count down when the training starts.

5. Press ST/STOP to start your training with TARGET H.R. mode.

Function buttons

START/STOP To start or stop monitor counting.

MODE To enter all functions, age, and training programs setting.

UP/DOWN To adjust and set all functions, personal datas, and training programs setting.

RESET To have the monitor jump to initial display for training mode selection. If you hold on

pressing the button for 2 seconds, the monitor will reset previous training and jump to

user code selection.

Functions

RPM To display current training rotations per minute.

SPEED To display current training speed.

TIME Count up - To accumulate training time from 0:00 to 99:59 with one second increment when the

training starts.(No preset target)

Count down - The monitor will start to count from preset time down to 0:00 with one second

decrement when the training starts. As soon as the preset time is achieved, the monitor starts to

alarm, and TIME will start to count up immediately from 0:00.

DISTANCE Count up - To accumulate training distance from 0.00 to 999.9 with 0.01 km (ml) increment

when the training starts. (No preset target)

Count down - The monitor will start to count from preset distance down to 0.00 with 0.01 km

or ml) decrement when the training starts. As soon as the preset distance is achieved, the monitor

starts to alarm, and DISTANCE will start to count up immediately from 0.00.

CALORIES Count up - To accumulate calories consumption from 0 to 9999 cal with one cal increment when

when the training starts. (No preset target)

Count down - The monitor starts to count from preset calories down to 0 with 1 cal decrement

when the training starts. As soon as the preset calories is achieved, the monitor starts to alarm,

and CALORIES will start to count up immediately from 0.

WATT To display the workout effort in figures.

- 15 -

PULSE The monitor can detect both chest pulse and hand pulse, the chest pulse is priority. It means if

you hold both hands on handlebar grip sensors and wear on the chest blet together, the monitor

will display chest pulse only. If you would like to have hand pulse readout, please do not wear

on the chest belt when you hold on handgrip sensors. The monitor start beep when your heart

rate figure is exceed the target.

Note

1. When you stop training and did not press any button for 4 minutes, the monitor will shut off automatically.

All previous training datas (Time,Distance,and Calories) will be stored.You may press any button or start

training again to wake up the monitor display.

2. You may have the monitor reset all function datas by hold on pressing the RESET button for 4 seconds.

3. The monitor requires power supply with AC adaptor input.(Out put 500mA, 6V)

Sportop E-8000P Owner's manual

Sportop E-8000P Owner's manual

Sportop E-8000P Owner's manual

Other documents