Dodge 2007 KA Nitro Owner's manual

TABLE OF CONTENTS

SECTION PAGE

1

INTRODUCTION

.............................................................3

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

.............................11

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

..............................77

4

INSTRUMENT PANEL AND CONTROLS

.........................................159

5

STARTING AND OPERATING

.................................................235

6

WHAT TO DO IN EMERGENCIES

..............................................323

7

MAINTAINING YOUR VEHICLE

...............................................335

8

MAINTENANCE SCHEDULES

..................................................385

9

IF YOU NEED CONSUMER ASSISTANCE

.........................................411

10

INDEX

....................................................................419

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS

䡵Introduction ........................... 4

▫Roll Over Warning ..................... 5

䡵How To Use This Manual .................. 6

䡵Warnings And Cautions ................... 8

䡵Vehicle Identification Number ............... 8

䡵Vehicle Modifications / Alterations ........... 9

1

INTRODUCTION

This manual has been prepared with the assistance of

service and engineering specialists to acquaint you with

the operation and maintenance of your new vehicle. It is

supplemented by a Warranty Information Booklet and

various customer oriented documents. You are urged to

read these publications carefully. Following the instruc-

tions and recommendations in this manual will help

assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored

in the vehicle for convenient reference and remain with

the vehicle when sold, so that the new owner will be

aware of all safety warnings.

When it comes to service, remember that your dealer

knows your vehicle best, has the factory-trained techni-

cians and genuine Mopar威parts, and is interested in

your satisfaction.

WARNING!

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals

known to the State of California to cause cancer and

birth defects or other reproductive harm. In addition,

certain fluids contained in vehicles and certain prod-

ucts of component wear contain or emit chemicals

known to the State of California to cause cancer and

birth defects or other reproductive harm.

4 INTRODUCTION

Roll Over Warning

Utility vehicles have a significantly higher roll over rate

than other types of vehicles. This vehicle has a higher

ground clearance, higher center of gravity, and narrower

track than many passenger cars. It is capable of perform-

ing better in a wide variety of off-road applications.

Driven in an unsafe manner, all vehicles can be caused to

go out of control. Because of the higher center of gravity

and the narrower track, if this vehicle is out of control it

may roll over when some other vehicles may not.

Do not attempt sharp turns or abrupt maneuvers or other

unsafe driving actions that can cause loss of vehicle

control. Failure to operate this vehicle safely may result

in an accident, roll over of the vehicle, and severe or fatal

injury. Drive carefully.

Failure to use driver and passenger seat belts provided

is a major cause of severe or fatal injury. In fact, the U.S.

government notes that the universal use of existing seat

belts could cut the highway death toll by 10,000 or more

each year, and could reduce disabling injuries by 2

Roll Over Warning Label

INTRODUCTION 5

1

million annually. In a roll over crash an unbelted person

is significantly more likely to die than a person wearing

a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section

contains the information you desire.

The detailed index, at the rear of this manual, contains a

complete listing of all subjects.

Consult the following table for a description of the

symbols that may be used on your vehicle or throughout

this owner manual:

6 INTRODUCTION

INTRODUCTION 7

1

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating

procedures which could result in an accident or bodily

injury. It also contains CAUTIONS against procedures

which could result in damage to your vehicle. If you do

not read this entire manual you may miss important

information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The vehicle identification number (VIN) is found on the

left front corner of the instrument panel area, visible

through the windshield. This number also appears on the

Automobile Information Disclosure Label affixed to a

window on your vehicle, the vehicle registration and

title. NOTE: It is illegal to remove the VIN.

Vehicle Identification Number

8 INTRODUCTION

VEHICLE MODIFICATIONS / ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle

could seriously affect its roadworthiness and safety

and may lead to an accident resulting in serious

injury or death.

INTRODUCTION 9

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

䡵A Word About Your Keys ..................14

▫Ignition Key Removal ...................14

▫Key-In-Ignition Reminder ................16

䡵Steering Wheel Lock — If Equipped ..........16

▫To Manually Lock The Steering Wheel .......16

▫To Release The Steering Wheel Lock .........16

䡵Sentry Key — If Equipped .................16

▫Replacement Keys ......................17

▫Customer Key Programming ..............18

▫General Information ....................19

䡵Security Alarm System — If Equipped .........19

▫ToSetTheAlarm ......................19

▫To Disarm The System ...................20

䡵Illuminated Entry ........................20

䡵Remote Keyless Entry .....................21

▫To Unlock The Doors And Liftgate ..........21

▫To Lock The Doors And Liftgate ............22

▫Using The Panic Alarm ..................23

2

▫Programming Additional Transmitters ........24

▫Battery Replacement ....................24

▫General Information ....................25

䡵Remote Starting System — If Equipped ........26

䡵Door Locks ............................27

▫Manual Door Locks .....................28

▫Power Door Locks .....................29

▫Child-Protection Door Lock System

(Rear Doors) ..........................30

䡵Windows .............................31

▫Power Windows .......................31

▫Wind Buffeting ........................35

䡵Liftgate ...............................35

䡵Occupant Restraints ......................36

▫Lap/Shoulder Belts .....................38

▫Lap/Shoulder Belt Operating Instructions .....39

▫Adjustable Upper Shoulder Belt Anchorage ....42

▫Automatic Locking Mode — If Equipped .....43

▫Energy Management Feature ..............43

▫Seat Belt Pretensioners ...................44

▫Enhanced Seat Belt Use Reminder System

(BeltAlert) ...........................44

▫Seat Belts And Pregnant Women ............45

▫Seat Belt Extender ......................46

▫Driver And Front Passenger Supplemental

Restraint Systems (SRS) ..................47

▫Child Restraint ........................64

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

䡵Engine Break-In Recommendations ...........74

䡵Safety Tips ............................74

▫Exhaust Gas ..........................74

▫Safety Checks You Should Make Inside The

Vehicle..............................75

▫Safety Checks You Should Make Outside The

Vehicle..............................76

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

2

A WORD ABOUT YOUR KEYS

The keys for your new vehicle are enclosed in a plastic

bag with the key code number on it. If you received your

keys without the bag, ask your dealer to give you the

number. The key code can also be obtained by the dealer

from your vehicle invoice.

Ignition Key Removal

Manual Transmission

Turn the ignition switch to the ACC position, push the

key and cylinder inward, rotate the key to the LOCK

position, and remove the key.

Ignition Key

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Automatic Transmission — If Equipped

Place the shift lever in P (Park). Turn the ignition switch

to the ACC position, push the key and cylinder inward,

rotate the key to the LOCK position, and remove the key.

WARNING!

Leaving children in a vehicle unattended is danger-

ous for a number of reasons. A child or others could

be injured. Children should be warned not to touch

the parking brake, brake pedal, or the gear selector

lever. Do not leave the keys in the ignition. A child

could operate power windows, other controls, or

move the vehicle.

CAUTION!

An unlocked vehicle is an invitation to thieves.

Always remove the key from the ignition, and lock

all doors when leaving the vehicle unattended.

Ignition Key Positions

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

2

Key-In-Ignition Reminder

Opening the driver’s door when the key is in the ignition,

sounds a signal to remind you to remove the key.

STEERING WHEEL LOCK — IF EQUIPPED

Your vehicle may be equipped with a passive steering

wheel lock (manual transmission only). This lock pre-

vents steering the vehicle without the ignition key. If the

steering wheel is moved a half turn in either direction

and the key is not in the ignition, the steering wheel will

lock.

To Manually Lock the Steering Wheel

With the engine running, rotate the steering wheel 1/2

revolution from straight ahead position, turn off the

engine and remove the key. Rotate the steering wheel

slightly in both directions until the lock engages.

To Release the Steering Wheel Lock

Insert the key in the ignition and turn the wheel slightly

to the right or left to disengage the lock.

NOTE: If you turned the wheel to the right to engage

the lock, you must turn the wheel slightly to the right to

disengage it. If you turned the wheel to the left to engage

the lock, turn the wheel slightly to the left to disengage it.

SENTRY KEY — IF EQUIPPED

The Sentry Key Immobilizer System prevents unautho-

rized vehicle operation by disabling the engine. The

system does not need to be armed or activated. Operation

is automatic, regardless of whether the vehicle is locked

or unlocked.

The system uses ignition keys, which have an embedded

electronic chip (transponder), to prevent unauthorized

vehicle operation. Therefore, only keys that are pro-

grammed to the vehicle can be used to start and operate

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

the vehicle. The system will shut the engine off in two (2)

seconds if someone uses an invalid key to start the

engine.

NOTE: A key that has not been programmed is consid-

ered an invalid key even if it is cut to fit the ignition lock

cylinder for that vehicle.

During normal operation, after turning on the ignition

switch, the “Vehicle Security Alarm Indicator Light” will

turn on for three (3) seconds for a bulb check. If the light

remains on after the bulb check, it indicates that there is

a problem with the electronics. In addition, if the light

begins to flash after the bulb check, it indicates that

someone used an invalid key to start the engine. Either of

these conditions will result in the engine being shut off

after two (2) seconds.

If the “Vehicle Security Alarm Indicator Light” turns on

during normal vehicle operation (vehicle running for

longer than 10 seconds), it indicates that there is a fault in

the electronics. Should this occur, have the vehicle ser-

viced as soon as possible.

Replacement Keys

NOTE: Only keys that have been programmed to the

vehicle electronics can be used to start the vehicle. Once

a Sentry Key has been programmed to a vehicle, it cannot

be programmed to any other vehicle.

At the time of purchase, the original owner is provided

with a four digit PIN. This number is required for dealer

replacement of keys. Duplication of keys may be per-

formed at an authorized dealer or by using the Customer

Key Programming procedure. This procedure consists of

programming a blank key to the vehicle electronics. A

blank key is one which has never been programmed and

needs to be cut.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

2

NOTE: When having the Sentry Key System serviced,

bring all vehicle keys to the dealer.

Customer Key Programming

You can program new keys to the system if you have two

valid keys by doing the following:

1. Cut the additional Sentry Key Transponder blank(s) to

match the ignition switch lock cylinder key code.

2. Insert the first valid key into the ignition switch and

turn the ignition switch ON for at least 3 seconds but no

longer than 15 seconds. Turn the ignition switch OFF and

remove the first key.

3. Insert the second valid key and turn the ignition

switch ON within 15 seconds. After ten seconds, a chime

will sound and the “Vehicle Theft Alarm Indicator Light”

will begin to flash. Turn the ignition switch OFF and

remove the second key.

4. Insert a blank Sentry Key into the ignition switch and

turn the ignition switch ON within 60 seconds. After 10

seconds, a single chime will sound and the “Vehicle Theft

Alarm Indicator Light” will stop flashing, turn on again

for 3 seconds, and then turn off.

The new Sentry Key has been programmed. The Keyless

Entry Transmitter will also be programmed during this

procedure. Repeat this procedure to program up to a

total of 8 keys. If you do not have a programmed sentry

key, contact your dealer for details.

NOTE: If a programmed key is lost, see your dealer to

have all remaining keys erased from the systems

memory. This will prevent the lost key from starting your

vehicle. The remaining keys must then be repro-

grammed. All vehicle keys must be taken to the dealer at

the time of service to be reprogrammed.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

General Information

The Sentry Key system complies with FCC rules part 15

and with RSS-210 of Industry Canada. Operation is

subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be

received, including interference that may cause undes-

ired operation.

SECURITY ALARM SYSTEM — IF EQUIPPED

This system monitors the vehicle doors, liftgate, and

ignition for unauthorized operation. When the alarm is

activated, the system provides both audible and visual

signals. The horn will sound repeatedly for three minutes

and the headlights and taillights will flash for an addi-

tional 15 minutes.

NOTE: The “Panic” and “Security” alarms are quite

different. Please take a moment to activate the “Panic”

and the “Security” modes to hear the differences in the

horn. In case one should go off in the future, you will

need to know which mode has been activated in order to

deactivate it.

To Set the Alarm

The alarm will set when you use the remote keyless entry

transmitter to lock the doors and liftgate or when you use

the power door lock switch while the door is open. After

all the doors are locked and closed, the “Vehicle Security

Alarm Indicator Light” (located in the instrument cluster)

will flash rapidly for about 16 seconds to signal that the

system is arming. During this 16 second pre-arm period,

opening any door or the liftgate will cancel the arming. If

the system successfully arms, the “Vehicle Security

Alarm Indicator Light” will flash at a slower rate to

indicate the alarm is set. A manual lock of the doors,

either with the door lock plunger located on the inside of

the doors or with the driver’s door key lock cylinder, will

not set the alarm.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

2

To Disarm the System

To disarm the system, use the remote keyless entry

transmitter. Also, using a valid sentry key and moving

the ignition switch to the ON/START position will

disarm the system. If something has triggered the system

in your absence, the horn will sound three times when

you unlock the doors. Check the vehicle for tampering.

The Security Alarm System is designed to protect your

vehicle; however, you can create conditions where the

system will arm unexpectedly. If you remain in the

vehicle and lock the doors with the transmitter, once the

system is armed (after 16 seconds), when you pull the

door handle to exit the alarm will sound. If this occurs,

press the “Unlock” button on the remote keyless entry

transmitter to disarm the system. The Security Alarm

System will not disarm with a manual unlock, either

through the lock plunger located on the inside of the

door, or through a key in the driver’s door key cylinder.

ILLUMINATED ENTRY

The interior lights come on when you open any door.

They will remain on for about 30 seconds after all doors

are closed then fade to off.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Page is loading ...

Dodge 2007 KA Nitro Owner's manual

This manual is also suitable for

Dodge 2007 KA Nitro Owner's manual

Related papers