UM-7HU0A-001
Switch Unit Integrated Type
Cycle Computer
User's Manual
SHIMANO Total Electric Power System
1
CONTENTS
IMPORTANT NOTICE
......................................................................................2
GENERAL SAFETY INFORMATION
..................................................................... 2
NOTICE
.......................................................................................................2
Regular inspections before riding the bicycle
....................................................3
Booklet Structure
.........................................................................................4
Names of parts
.............................................................................................5
Notation method for operations ...............................................................................................6
Installing and removing the cycle computer
......................................................6
Basic operation
............................................................................................7
Turning the power ON/OFF ........................................................................................................7
Viewing the screen .....................................................................................................................8
Battery level indicator ................................................................................................................9
Turning the light ON/OFF .........................................................................................................10
Switching the traveling data display .......................................................................................11
Display units ..............................................................................................................................11
Resetting the traveling distance ..............................................................................................12
Gear position when starting from a stop [Start mode] ..........................................................12
Making walking and pushing the bicycle easy (walk assist) ..................................................13
External connections
...................................................................................15
E-TUBE PROJECT ........................................................................................................................15
Items configurable in E-TUBE PROJECT ...................................................................................15
Troubleshooting
.........................................................................................15
Gear shifting adjustment with the electronic gear shifting unit [ADJUST] ..........................15
Warning indication ...................................................................................................................16
Error indication .........................................................................................................................17
When a problem occurs ............................................................................................................19
2
IMPORTANT NOTICE
•
Contact the place of purchase or a distributor for
information on installation, adjustment, and replacement
of the products which are not found in the user's manual.
The dealer's manual for professional bicycle mechanics is
available from our website
(https://si.shimano.com).
•
Please observe the appropriate rules and regulations of
the country, state or region in which you conduct your
business as a dealer.
For safety, be sure to read this “user's
manual” thoroughly before use, follow it
for correct use, and store it so that it can
be referenced at any time.
The following instructions must be observed at all times in
order to prevent personal injury and physical damage to
equipment and surroundings. The instructions are classified
according to the degree of danger or damage which may
occur if the product is used incorrectly.
DANGER
Failure to follow the instructions will result in death or
serious injury.
WARNING
Failure to follow the instructions could result in death or
serious injury.
CAUTION
Failure to follow the instructions could cause personal
injury or physical damage to equipment and surroundings.
GENERAL SAFETY
INFORMATION
WARNING
•
Do not disassemble or modify the product. This may
cause the product to not operate correctly, and you may
suddenly fall and be seriously injured.
Riding precautions
•
Do not to pay excessive attention to the cycle computer
display while riding.
Doing so may result in an accident.
•
Confirm that the light works before riding.
Safety precautions
•
Be sure to remove the battery and charging cable before
wiring or attaching parts to the bicycle.
Failure to do so may cause an electric shock.
•
Be sure to follow the instructions provided in the
manuals when installing the product.
It is recommended that you use SHIMANO genuine parts.
If bolts and nuts become loose or the product is
damaged, the bicycle may suddenly fall over, resulting in
a serious injury.
•
Do not leave this product in an extremely high
temperature surrounding environment such as in a closed
vehicle on a hot day, or near a heater. That can result in
an explosion of the incorporated battery or the leakage
of flammable liquid or gas from it.
•
Do not subject this product to extremely low air pressure.
That can result in an explosion of the incorporated
battery or the leakage of flammable liquid or gas from it.
Transporting this product by air is not a problem.
Disposal precautions
•
Observe all federal, state and local environmental
regulations when disposing of this product, because it
incorporates a battery. Disposal of this product into fire
or a hot oven, or mechanically crushing or cutting it can
result in an explosion of the incorporated battery.
CAUTION
Riding precautions
•
Observe the instructions in the manual for the bicycle in
order to ride safely.
Safety precautions
•
Never modify the system.
Doing so may cause a system error.
•
Use the product under the supervision of someone
responsible for safety, and only as instructed.
Do not allow anyone (including children) with reduced
physical, sensual, or mental capacity, or those without
experience or knowledge, to use the product.
•
Do not allow children to play near the product.
NOTICE
Safety precautions
•
If any malfunction or trouble occurs, consult the place of
purchase nearest you.
•
Be sure to attach caps to any unused connectors.
3
•
For installation and adjustment of the product, consult
the place of purchase.
•
The components are designed to be fully waterproofed
to withstand wet weather riding conditions; however, do
not deliberately place them into water.
•
Do not clean the bicycle with a high-pressure washer. If
water gets into any of the components, operating
problems or rusting may result.
•
Do not turn the bicycle upside down. There is a risk of
damage to the cycle computer and switch unit.
•
Handle the components carefully, and avoid subjecting
them to strong shock.
•
Although the bicycle still functions as a normal bicycle
even when the battery is removed, the light will not turn
on if it is connected to the electric power system. Be
aware that using the bicycle under these conditions will
be considered non-observance of the road traffic laws in
Germany.
Connection and communication with PC
A PC linkage device can be used to connect a PC to the
bicycle (system or components), and E-TUBE PROJECT can be
used to carry out tasks such as customizing single
components or the whole system and updating firmware.
•
PC linkage device: SM-PCE1/SM-PCE02
•
E-TUBE PROJECT: PC application
•
Firmware: Software inside each component
Care and maintenance
•
Contact the place of purchase for updates of the
component software. The most up-to-date information is
available on the SHIMANO website.
•
Do not use thinner or other solvents to clean any of the
components. Such substances may damage the surface.
•
For any questions regarding methods of installation and
maintenance, please contact your place of purchase.
•
Products are not guaranteed against natural wear and
deterioration from normal use and aging.
•
For maximum performance we highly recommend
SHIMANO lubricants and maintenance products.
Labels
•
Some of the important information contained in this
user's manual is also indicated on the device label.
Regular inspections before
riding the bicycle
Check the following prior before riding the bicycle. If any
problems are found, consult your place of purchase or a
distributor.
•
Does the drive train perform gear shifting smoothly?
•
Are the components fixed securely and free from
damage?
•
Are the components securely installed to the frame/
handlebar/stem, etc. ?
•
Do any abnormal noises occur while riding?
•
Is there sufficient charge remaining in the battery?
4
Booklet Structure
SHIMANO STEPS user's manuals are split among several booklets, as described below.
Be sure to read these user's manuals thoroughly before use, and follow them for correct use. Store the user's manuals so that
they can be referenced at any time.
The latest user's manuals are available on our website (https://si.shimano.com).
•
SHIMANO STEPS user's manual
This is the basic user's manual for SHIMANO STEPS. It contains the following content.
-
SHIMANO STEPS quick guide
-
How to operate assist bicycles that use flat handlebars, such as city, trekking, or MTB type bicycles
-
Troubleshooting
•
SHIMANO STEPS user's manual for drop handlebar bicycles (separate booklet)
This booklet describes how to operate assist bicycles that use a drop handlebar and are controlled using a dual control
lever. This should be read along with the SHIMANO STEPS user's manual.
•
SHIMANO STEPS special battery and parts user's manual
It contains the following content.
-
How to charge and handle the SHIMANO STEPS special battery
-
How to attach and remove the SHIMANO STEPS special battery to the bicycle
-
How to use the satellite power button and satellite charging port
-
How to read the battery LEDs when charging or during an error, and how to handle errors
•
Cycle computer user's manual (this document)
It contains the following content.
-
Basic operations of the cycle computer and how to configure settings
-
Wireless communication method (supported models only)
-
How to handle errors/warnings and cycle computer troubleshooting
•
Switch unit user's manual
This is the assist switch and shifting switch user's manual. It describes switch unit operations.
5
Names of parts
3-type switch switch unit (right)
2-type switch
switch unit (right)
MTB type
switch unit (right)
Light button
Switch unit integrated type
cycle computer
X Y
X
A
Y
X
A
Y
X
Y
The operation for each button is indicated below.
Switch unit integrated type cycle computer Switch unit (right)
Button-X
Increase assistance
When in walk assist mode: Disengage walk
assist mode *2
Button-X Shifting up
Button-Y
Decrease assistance
Hold down: Switch to walk assist mode *2
When in walk assist mode: Activate walk
assist *2
Button-Y Shifting down
Button-A Switching traveling data display Button-A*1
Switch between automatic and manual gear
shifting
*1 Only enabled when the assist bicycle supports automatic gear shifting.
*2 Depending on the region of use, you may not be able to use it due to the laws of the region. Refer to “Making walking
and pushing the bicycle easy (walk assist)” for details on walk assist mode.
6
• When connected to the E-TUBE PROJECT, you can change the functions assigned to each button on the switch unit. Please contact your
place of purchase for details.
• The button layout may differ according to the switch unit. Refer to the “Switch unit user's manual” for details.
Notation method for operations
Subsequent operations using the main body button and switch unit of this product are indicated using the following
notation.
Notation Operation
<X> Indicates an operation for pressing button-X of the cycle computer.
<A> Indicates an operation for pressing button-A of the cycle computer.
[AUTO]
(Example) Auto gear
shifting mode
Items displayed on the cycle computer screen are enclosed in square brackets in this
manual.
Installing and removing the cycle computer
For the installation/removal procedure, contact your place of purchase or the distributor.
7
Basic operation
Turning the power ON/OFF
The power of this product is linked with the main power of the assist bicycle. When the main power is turned ON, all
components connected to the drive unit of the assist bicycle are also turned ON (such as assist driving, the power of this
product, the electronic gear shifting mechanism, and the lights).
For the procedure for turning the main power ON/OFF, refer to the “SHIMANO STEPS user's manual.”
NOTICE
• Before turning the power ON, please refer to the “SHIMANO STEPS special battery and parts user's manual” to check the following.
- The battery is firmly attached to the battery mount
• The power cannot be turned ON while charging.
• If the bicycle is left unused for 10 minutes or more after turning the power ON, the power automatically turns OFF (auto power OFF
function).
When the main power is turned ON, a screen similar to that shown below is displayed, and then switches to the main screen.
8
Viewing the screen
The items displayed on the main screen differ according to the assist bicycle.
Main screen
(A)
(D)
(C)
(E)
(B)
(G)
(F)
(H)
(A)
Battery level indicator
(Refer to “Battery level indicator”)
(E)
ADJUST mode display
(Refer to “NOTICE” below)
(B)
Current speed
Displays the current speed. (Refer to “Display
units”)
(F)
Assist gauge
Displays the current assist mode. A mode that
provides stronger assistance the longer the
length of the displayed gauge.
(C)
Auto gear shifting mode display
Displayed for the auto gear shifting mode.
(G)
Walk assist*1
This icon is displayed when switched to walk
assist mode.
(D)
Traveling data display
(Refer to “Switching the traveling data display”)
(H)
Maintenance alert
Indicates that maintenance is required. Contact
your place of purchase or a distributor if this
icon is displayed.
*1 Depending on the region of use, you may not be able to use it due to the laws of the region. Refer to “Making walking
and pushing the bicycle easy (walk assist)” for details on walk assist mode.
NOTICE
If you are unable to change gears using the electronic gear shifting, check the cycle computer display for the following.
•
If [ADJUST] is displayed on the screen, press <A> on the cycle computer to return to the main screen.
•
If the walk assist icon is displayed on the screen, press <X> on the cycle computer to disengage walk assist mode.
•
Refer to “Warning indications” and “Error indications” also.
Example of ADJUST mode screen Example of walk assist icon display
9
Battery level indicator
The battery level is shown as an icon.
Display Battery level
100 - 81%
80 - 61%
60 - 41%
40 - 21%
20 - 1% *
0%
*
The battery level indicator will flash when the battery level is low if the assist mode is set to something other than
[OFF].
• The cycle computer uses zero to indicate a battery level where assistance cannot be performed. With the SHIMANO STEPS system, the light
can still be lit up for a while when assist stops due to a low battery. Therefore, the above-mentioned battery level may differ from that
which can be checked on the battery.
10
Turning the light ON/OFF
If a light is connected to the drive unit, this product can be used to operate the light.
1.
Press the light button.
Light button
• The light power is linked with the main power. The light cannot be turned ON when the main power is OFF.
11
Switching the traveling data display
On the main screen, you can check various traveling data in addition to the current speed. The traveling data that can be
displayed differs according to the assist bicycle.
1.
On the main screen: Press <A>.
Current gear position Traveling range
The traveling data switches in the following order each time <A> is pressed.
Display item Explanation
[GEAR] Current gear position*1
[RANGE] Traveling range*2
[DST] Traveling distance
[ODO] Cumulative distance
*1 Only displayed for electronic gear shifting.
*2 The traveling range (reference value) for the selected assist mode. The display switches each time the assist mode is
switched. The value is not displayed when the assist mode is set to [OFF].
• If the traveling data display is switched when [ODO] is displayed, the screen will switch back to displaying [GEAR] (for electronic gear
shifting) or [RANGE] (for mechanical gear shifting).
• The traveling data display condition that was last displayed is retained even when the power is turned OFF.
• Even when the traveling data display is switched to something other than [GEAR], the screen will switch to displaying [GEAR] for
approximately two seconds when a gear shift operation is performed.
Display units
This product can switch the display units of speed, traveling distance, and cumulative distance to km or miles. It is
necessary to connect to E-TUBE PROJECT (PC version) to switch the display units. For the connection method and setting
procedure, contact your place of purchase.
Displayed in km Displayed in miles
12
Resetting the traveling distance
The traveling distance is reset from the main screen.
1.
On the main screen: Press <A>. (Switches the traveling data display to [DST])
2.
Hold down <A>. (Continue to hold down until the
number displayed for [DST] flashes)
3.
When the number displayed for [DST] is flashing:
Press <A>.
The traveling data is reset.
• If nothing is done for five seconds after the number for [DST] begins flashing, it will stop flashing and the screen will return to the main
screen. The display will automatically return to the main screen when the start of traveling is detected.
Gear position when starting from a stop [Start mode]
The assist bicycle where this product is installed may be set to automatically switch to a gear where it is easier to start riding
again after stopping. If you want to change this setting, contact your place of purchase.
13
Making walking and pushing the bicycle easy (walk assist)
Depending on the region of use, you may not be able to use it due to the laws of the region. In this case, the operations
described here are disabled.
1.
Stop and switch to walk assist mode.
Hold down button-Y until it reaches the following state.
X
Y
Walk assist icon
• If nothing is done for one minute after switching to walk assist mode, it will switch back to the assist mode that was selected before
switching.
2.
Push the bicycle carefully while pressing the same button again.
If you let go of button-Y, the assist stops.
X
Y
14
NOTICE
Walk assist operates at a maximum of 6 km/h. Be careful because the bicycle starts moving just by button operations.
• During electronic gear shifting, the assistance of walk assist and speed are controlled by the current gear position.
3.
Exit walk assist mode.
Press button-X.
X
Y
15
External connections
This product has a function for communicating with a PC. For the connection method, contact your place of purchase.
E-TUBE PROJECT
E-TUBE PROJECT is needed to change the setting of the SHIMANO STEPS and to update firmware.
Download E-TUBE PROJECT from our support website (https://e-tubeproject.shimano.com).
For information on how to install E-TUBE PROJECT, check the support website.
NOTICE
Do not connect to a device while the battery is being charged.
• Firmware is subject to change without notice.
Items configurable in E-TUBE PROJECT
The items that can be set differ according to the assist bicycle. Refer to the help manual for E-TUBE PROJECT for details.
•
You can change the functions assigned to each operation switch in [Switch setting].
•
You can change the display units for speeds and distances in [Display units].
•
You can set/change the gear when starting from a stop in [Start mode]. (Internal electronic gear shifting only)
•
You can select to have the backlight of the display always ON, always OFF, or linked to the light in [Backlight setting].
Troubleshooting
Gear shifting adjustment with the electronic gear shifting unit [ADJUST]
If gear shifting feels abnormal, contact the place of purchase.
16
Warning indication
If the situation is resolved, this indication will disappear. If the situation does not improve, contact the place of purchase.
• Error and warning indications are subject to change without
notice. For the most up-to-date information, check our support
website (https://e-tubeproject.shimano.com).
Code*1 Indication conditions
Operational restrictions
being displayed
Remedy
W101
(W011)
Traveling speed not
detected.
The maximum speed
up to which assist is
provided will be lower
than normal.
Have your place of purchase perform the following.
• Check to see if the speed sensor is installed in the
correct position.
• Check to see if the magnet on the disc brake rotor is
attached. (Refer to the “Disc brake” section in
“General operations” for how to install the removed
magnet.)
W103
(W013)
Initialization did not
complete normally
for the torque
sensor.
Assistance will be
lower than normal.
Press the battery power button without stepping on the
pedal to turn the power ON again.
W104
Current leakage
detected in the
system and power
turned OFF.
Assist will not be
provided when riding.
Have your place of purchase perform the following.
Remove the components other than the drive unit one
by one, then turn the power back ON.
• If the component with a problem has not been
removed, the power turns OFF during startup.
• If the component with a problem has been removed,
the power turns ON and W104 remains displayed.
W105
Unexpected power
disconnection
detected.
-
Refer to the “SHIMANO STEPS user's manual” and turn
the power OFF and then ON again.
If W105 is displayed frequently, have your place of
purchase perform the following.
• Check to see if the battery holder rattles or if the
power cord is disconnected.
W200
(W020)
If the temperature
exceeds the
guaranteed
operating range, the
battery output stops.
No system functions
will start.
If the temperature is higher than the temperature at
which discharging is possible, leave the battery in a cool
location with no direct sunlight until the internal
temperature of the battery has decreased sufficiently. If
the temperature is lower than the temperature at
which discharging is possible, leave the battery indoors
until the internal temperature has increased to an
appropriate temperature.
17
Code*1 Indication conditions
Operational restrictions
being displayed
Remedy
W302
(W032)
Shifting unit
different from
system configuration
is installed.
Unable to perform
gear shifting.
Have your place of purchase perform the following.
Replace with the shifting unit configured in the system.
Or check the current system status with
E-TUBE PROJECT.
*1 The code displayed in parentheses may be displayed, depending on the drive unit that is connected.
Error indication
If an error message is displayed on the entire screen, refer to the “SHIMANO STEPS special battery and parts user's
manual” and follow one of the procedures below to reset the display.
•
Press the battery power button to turn the power OFF.
•
Remove the battery from the battery mount.
• Error and warning indications are subject to change without
notice. For the most up-to-date information, check our support
website (https://e-tubeproject.shimano.com).
NOTICE
• If the situation does not improve even after turning the power back ON, consult with the place of purchase or a distributor.
Code*1
Indication
conditions
Operational restrictions
being displayed
Remedy
E010
System error
detected.
Assist will not be provided
when riding.
Refer to the "SHIMANO STEPS User's manual" to
turn the power OFF and then ON again. If the
situation does not improve, contact the place of
purchase or a distributor.
E020
Communication
error between the
battery and drive
unit detected.
Assist will not be provided
when riding.
Have your place of purchase perform the following.
•
Check to see if the cable between the drive unit
and battery is connected correctly.
E021
Battery connected
to drive unit
conforms with
system standards
but is not
supported.
Assist will not be provided
when riding.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check
the power cord for abnormalities. If the error
persists, contact your distributor.
E022
Battery connected
to drive unit does
not conform with
system standards.
No system functions will
start.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check
the power cord for abnormalities. If the error
persists, contact your distributor.
18
Code*1
Indication
conditions
Operational restrictions
being displayed
Remedy
E023
Electrical
abnormality in
battery detected.
No system functions will
start.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check
the power cord for abnormalities. If the error
persists, contact your distributor.
E024
Battery overcurrent
protection
occurred.
No system functions will
start.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check
the power cord for abnormalities. If the error
persists, contact your distributor.
E025
Battery does not
recognize the drive
unit.
No system functions will
start.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check
the power cord for abnormalities. If the error
persists, contact your distributor.
E030
Shifting unit
different from
system
configuration is
installed.
Assist will not be provided
when riding.
Have your place of purchase perform the following.
Replace with the shifting unit configured in the
system. Or check the current system status with
E-TUBE PROJECT.
E033
Current firmware is
not supported by
this system.
Assist will not be provided
when riding.
Have your place of purchase perform the following.
Connect to E-TUBE PROJECT to update the firmware
on all the assist bicycle units to the latest version.
E034
(E013)
Abnormality
detected in drive
unit’s firmware.
Assist will not be provided
when riding.
Contact your place of purchase or a distributor. The
firmware needs to be restored.
E035
Configuration
error.
Assist will not be provided
when riding.
Have your place of purchase perform the following.
Connect to E-TUBE PROJECT to check the
configuration.
E043
Abnormality
detected in
firmware on this
product. Part of
the firmware may
be corrupted.
Assist will not be provided
when riding.
Contact your place of purchase or a distributor. The
firmware needs to be restored.
E050
(E014)
Speed sensor may
be installed in an
incorrect position.
Assist will not be provided
when riding.
Have your place of purchase perform the following.
Check to see if the speed sensor is installed in the
correct position. If not installed in the correct
position, install it in the correct position and ride
the bicycle for a while. Doing so should fix the
error. If the error persists, contact your distributor.
*1 The code displayed in parentheses may be displayed, depending on the drive unit that is connected.
19
When a problem occurs
Symptoms Possible cause Remedy
The cycle computer screen
does not light up when the
(main) battery power
button is pressed.
The (main) battery level may be too low.
Refer to the “SHIMANO STEPS special
battery and parts user's manual” to charge
the battery, and then turn the power ON
again.
Is the power ON?
Refer the “SHIMANO STEPS special battery
and parts user's manual” to turn the power
ON.
Is the battery charging?
When charging with the battery installed
to a bicycle, you cannot turn the power ON.
Stop charging.
Is the connector of the electric wire
installed correctly?
Check whether the connector of the electric
wire is disconnected. If you are not sure,
contact the place of purchase.
A product that the system cannot identify
may be connected.
Contact the place of purchase.
The gear position is not
displayed.
The gear position is only displayed when
the electronic gear shifting unit is installed.
Check whether the connector of the electric
wire is disconnected. If you are not sure,
contact the place of purchase.
The gear shifts by itself
when the bicycle starts from
a stop.
On bicycles with internal electronic gear
shifting specifications, the bicycle may be
set in advance to automatically switch to a
gear where it is easy to start from a stop
([Start mode]).
It is necessary to connect to E-TUBE
PROJECT to disable or change the setting of
[Start mode]. Contact the place of
purchase.
The gear position set in
[Start mode] is not set when
the bicycle is stopped.
You may have pressed the pedal too
strongly.
Pressing the pedal gently makes it easier to
shift gears.
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
