Steam en
19
Setting
Before applying the settings, fill up the water reservoir.
1. Select a suitable type of heating and temperature.
2. Touch the S field.
The steam level will be highlighted in white next to
the temperature on the display.
3. Turn the rotary selector to set the steam level.
4. Press the l Start/Stop button to start.
The appliance begins to heat up.
Note: If the water tank runs dry during an operation with
steam assistance, a message appears on the display
prompting you to fill up the water tank. The operation
continues without adding steam.
Changing and cancelling
To change the steam level, touch the S symbol. The
steam level will be highlighted in white, and can be
changed using the control ring. The change will be
applied immediately.
If you want to cancel steam assistance, touch the
S symbol again. The appliance will continue to operate,
but steam will not be injected into the cooking
compartment.
Reheating
With the "Reheating U" type of heating, you can gently
reheat food that has already been cooked or crisp up
day-old baked goods. Steam is switched on
automatically.
Note: If the water tank runs dry during the operation
with the Reheating setting, the operation is interrupted.
Fill the water tank.
Setting
A cooking time must always be set for the steam
heating types.
Before applying the settings, fill up the water reservoir.
1. Set the type of heating.
2. Touch the } field.
The temperature is highlighted in white in the
display.
3. Turn the rotary selector to set the temperature.
4. Touch the s field.
The cooking time is highlighted in white in the
display.
5. Turn the rotary selector to set the cooking time.
6. Press the l Start/Stop button to start.
The cooking time counts down in the display.
The appliance begins to heat up.
Once the cooking time has elapsed, an audible signal
sounds. The appliance stops heating up. The cooking
time 00 m 00 s is shown on the display.
When your dish is ready, use the ÿ On/Off button to
switch off the appliance.
Change
After starting the appliance, the temperature remains
highlighted. When you move the rotary selector, the
temperature is changed and applied immediately.
Touch the s symbol and turn the control ring to change
the cooking time. The change is applied immediately.
To change the type of heating, interrupt the operation
beforehand using the l Start/Stop button.
Note: When you change the type of heating, the other
settings will also be reset.
Dough proving setting
Dough will prove considerably more quickly using the
"Dough proving T" type of heating than at room
temperature and does not dry out.
Use the information in the tables to select the
appropriate setting. ~ "Tested for you in our cooking
studio" on page 35
Note: If the water tank runs dry during the operation
with the Dough proving setting, the operation is
interrupted. Fill the water tank.
Setting
A cooking time must always be set for the steam
heating types.
Before applying the settings, fill up the water reservoir.
1. Set the type of heating.
2. Touch the } field.
The temperature is highlighted in white in the
display.
3. Turn the rotary selector to set the temperature.
4. Touch the s field.
The cooking time is highlighted in white in the
display.
5. Turn the rotary selector to set the cooking time.
6. Press the l Start/Stop button to start.
The cooking time counts down in the display.
The appliance begins to heat up.
Once the cooking time has elapsed, an audible signal
sounds. The appliance stops heating up. The cooking
time 00 m 00 s is shown on the display.
When your dish is ready, use the ÿ On/Off button to
switch off the appliance.
Change
After starting the appliance, the temperature remains
highlighted. When you move the rotary selector, the
temperature is changed and applied immediately.
Touch the s symbol and turn the control ring to change
the cooking time. The change is applied immediately.
To change the type of heating, interrupt the operation
beforehand using the l Start/Stop button.
Note: When you change the type of heating, the other
settings will also be reset.
Filling the water tank
The water tank is located behind the control panel.
Before starting an operation with steam, open the
control panel and fill the water tank with water.
Make sure that you have set the water hardness range
correctly. ~ "Basic settings" on page 22