Seco SBC-SANTVEND-MX6 Owner's manual

Brand
Seco
Model
SBC-SANTVEND-MX6
Type
Owner's manual
SANTVEND core
Arm® Cortex®-A9 Single Board Computer
Product Manual
Vending / IOT platform with 3G / 4G modem and MDB interfaces.
Revision Date Author Description
V 1 10.02.2017 CG Initial Release
V 2 12.09.2019 CG Change address
V 3 17.12.2021 bmy SECO CI Update 2022
PRODUCT MANUAL
SANTVEND core
Document Revision History
The information in this document is subject to change without prior notice in order to improve reliability, design and
function and does not represent a commitment on the part of the manufacturer.
Online support on edge.seco.com
2
PRODUCT MANUAL
SANTVEND core
Table of Contents
1. Introduction .........................................................................................4
2. Safety Hints .........................................................................................5
3. Product Introduction .......................................................................... 7
3.1 Type Plate and Device Information ..............................................................7
3.2 Related Documents and Online Support .................................................... 8
4. Technical Data .....................................................................................9
4.1 Block Diagram ................................................................................................10
4.2 Technical Drawing ..........................................................................................11
4.3 PCB Design and Pin Assembly ....................................................................12
5. Installation and Start Up .....................................................................14
5.1 Connection Scheme ......................................................................................14
6. Internal and External Interfaces ........................................................15
6.1 Antenna GPS (X1703) ...................................................................................15
6.2 Antenna GSM (X1700) ..................................................................................15
6.3 MDB (X1500) ..................................................................................................16
6.4 Power (X200) ..................................................................................................17
6.5 Li - Ion - Akku (X201) .....................................................................................18
Recommendation for an suitable Li-Ion-Accumulator ...........18
6.6 RS-232 (X1401) .............................................................................................. 19
6.7 Speaker (X1301) ............................................................................................20
6.8 Microphone (X1300) ......................................................................................20
6.9 CAN (X1400) ...................................................................................................21
6.10 Ethernet (X1200) ............................................................................................22
6.11 USB - Host (X900)..........................................................................................23
6.12 Push - Buttons (SW600), (SW601), (SW1600), (SW1601) ......................23
6.13 JTAG - Debug Interface (X600) .................................................................... 24
6.14 HDMI (X704) ...................................................................................................24
6.15 LVDS 0 (X700) LVDS 1 (X701) ..................................................................... 25
6.16 2nd BL-CTRL (X703) .....................................................................................26
6.17 Backlight & PWM (X705) .............................................................................26
6.18 Ambient Light Sensor (X904) .......................................................................27
6.19 Touch, 3.3 Vcc (X907) ...................................................................................27
6.20 Touch, 5.0 Vcc (X902) ...................................................................................27
6.21 INSIKA (X1800) optional reserved for Internal Use ..................................28
Annex A: Hardware Revision Information .........................................................29
Annex B: Assembly Options ...............................................................................30
B-1 WIFI / Bluetooth ..............................................................................................30
Annex C: Guidelines and Standards .................................................................31
C-1 RoHS Declaration ...........................................................................................31
C-2 Supplier Declaration – Directive EG 1907/2006 REACH .......................... 31
C-3 ULCertication ............................................................................................... 31
C-4 SECO Northern Europe Comformity Statement ........................................31
Annex D: Common Documentation ....................................................................32
D-1 Warranty hints ................................................................................................. 32
D-2 Field of Application.........................................................................................33
Annex E: Technical Support ..............................................................................34
General Informations ..................................................................35
PRODUCT MANUAL
SANTVEND core
1. Introduction
Thank you very much for purchasing a SECO Northern Europe product. Our products are dedicated to professional
use and therefore we suppose extended technical knowledge and practice in working with such products.
The information in this manual is subject to technical changes, particularly as a result of continuous
product upgrades. Thus this manual only reflects the technical status of the products at the time
of printing. Before design-in the device into your or your customer’s product, please verify that this
document and the therein described specication is the latest revision and matches to the PCB
version. We highly recommend contacting our technical sales team prior to any activity of that kind.
The attached documentation does not entail any guarantee on the part of SECO Northern Europe
GmbH with respect to technical processes described in the manual or any product characteristics
set out in the manual. We do not accept any liability for any printing errors or other inaccuracies in
the manual unless it can be proven that we are aware of such errors or inaccuracies or that we are
unaware of these as a result of gross negligence and
SECO Northern Europe has failed to eliminate these errors or inaccuracies for this reason.
SECO Northern Europe GmbH expressly informs that this manual only contains a general
description of technical processes and instructions which may not be applicable in every individual
case. In cases of doubt, please contact our technical sales team.
In no event, SECO Northern Europe is liable for any direct, indirect, special, incidental or
consequential damages arising out of use or resulting from non-compliancy of therein conditions
and precautions, even if advised of the possibility of such damages.
Before using a device covered by this document, please carefully read
Annex „D-1 Warranty hints“
Annex „D-2 Field of Application“
Embedded systems are complex and sensitive electronic products. Please act carefully and ensure
that only qualied personnel will handle and use the device at the stage of development. In the
event of damage to the device caused by failure to observe the hints in this manual and on the
device (especially the safety instructions), SECO Northern Europe shall not be required to honour
the warranty even during the warranty period and shall be exempted from the statutory accident
liability obligation. Attempting to repair or modify the product also voids all warranty claims.
4
PRODUCT MANUAL
SANTVEND core
2. Safety Hints
Please read this section carefully and observe the instructions for your own safety and correct use of the device.
Observe the warnings and instructions on the device and in the manual. SECO Northern Europe embedded
systems have been built and tested by us and left the company in a perfectly safe condition.In order to maintain this
condition and ensure safe operation, the user must observe the instructions and warnings contained in this manual.
I. General Handling
Don’t drop or strike the unit: The PCB, display and/or other parts might be damaged.
Keep away from water and other liquids, the unit is not protected against.
Operate the unit under electrical and environmental conditions according to the technical
specication.
The electrical installations in the room must correspond to the requirements of the local (country-
specic) regulations.
Take care that there are no cables, particularly power cables, in areas where persons can trip over
them.
Do not place the device in direct sunlight, near heat sources or in a damp place.
All plugs on the connection cables must be screwed or locked to the housing.
Repairs may only be carried out by qualied specialist personnel authorized by
SECO Northern Europe GmbH or their local distributors.
Maintenance or repair on the open device may only be carried out by qualied personnel
authorized by SECO Northern Europe GmbH which is aware of with the associated dangers.
II. GSM - Module / SIM Card
It is the responsibility of the user to enforce the country regulation and the specic environment
regulation. Do not insert or remove the SIM when the product is powered.
Every module has to be equipped with a proper antenna with specic characteristics. The antenna
has to be installed with care in order to avoid any interference with other electronic devices and
has to guarantee a minimum distance from the body (20 cm).
It must be assumed that a safe operation is no longer possible, in case
Switch off your wireless device when in hospitals, clinics or other health care facilities. These
requests are designed to prevent possible interference with sentitive medical equipment.
Your cellular terminal or mobile contains a transmitter and receiver. When it is ON , it receives and
transmits radio frequency energy. RF interference can occur if it is used close to TV set, radio,
computer or other electric equipment.
In locations with potencially explosive atmospheres, obey all posted signs to turn off wireless
devices such as your phone or other cellular terminals. Areas with potencially explosive
atmospheres include fuelling areas, below decks on boats, fuel or chemical transfer or storage
facilities, areas where the air contains chemicals or particles such as grain, dust or metal powders,
etc.
5
PRODUCT MANUAL
SANTVEND core
III. Electricity
The embedded systems may only be opened in accordance with the description in this user’s
manual for
- replacing of the (rechargeable, where applicable) lithium battery and/or
- conguration of interfaces, where applicable
These procedures have to be carried-out only by qualied specialist personnel.
When accessing internal components the device must be switched off and disconnected from the
power source.
When purchased core or basic versions without protecting back cover, don’t touch the PCB directly
with your ngers. Especially these products need to be handled very carefully.
Don’t operate or handle the unit without typical ESD protection measures, such as ground
earthing.
Operate the unit according to the technical specication only.
IV. Damage or Permanent Malfunction
It must be assumed that a safe operation is no longer possible, in case
-the device has visible damage or
-the display is dark or shows strange pattern for longer period
-the device doesn’t react after a reset
In these cases the device must be shut down and secured against further use
6
PRODUCT MANUAL
SANTVEND core
3. Product Introduction
This document is applicable for hardware revisions 1.0 or later of the SANTVEND series.
Please nd the hardware version grid in „Annex A: Hardware Revision Information“:
SANTVEND is an Embedded System to be used as human machine interface (HMI) in various applications. Please
refer to Annex „D-2 Field of Application“ for further information. The system is equipped with a large number of
industrial interfaces. A wide variety of options is available as well.
3.1 Type Plate and Device Information
For service and later identication of the device, the type plate contains important information.
code denes the serial number
7

Linux Yocto Rocko
https://bit.ly/3G5Dq1e
Contains information about Linux BSP with development environment
Linux Embedded System Yocto (Codename: Jethro, Version 3.0) includes
rst information about the bootloader Flash-N-Go
PRODUCT MANUAL
SANTVEND core
3.2 Related Documents and Online Support
This document contains SBC specic information. The following additional documentations are available:
OPERATING SYSTEMS
8
CPU x2
CPU Type i.MX6Dual
Core Class Arm® Cortex®-A9
Core Clock 1 GHz
Features
NEON for SIMD media acceleration and VFP operations; Multi-format HD 1080p video decoder and HD
720p video encoder hardware engine; L1 cache, 32 KB for instruction, 32 KB for data; 1 MB L2 cache
512 KB L2 cache
HW Accelerators Open VG 1.1
RTC Accuracy: +/- 30 ppm at 25°C
Super Cap Buffer for 24h
Memory
eMMC Flash 4 GB MLC eMMC
RAM Standard 2 GB 32 bit DDR3L
Micro SD Card Slot 4 bit MMC/SDIO/SD/SDHC
Operating Systems
Supported OS Linux Yocto
Communication Interfaces
Network 1x 10/100 Mbit/s Ethernet (RJ-45)
USB 2.0 1x 480 Mbit/s Type A (Host)
CAN Fieldbus 1x CAN (ISO/DIS 11898)
MDB 1x Master, 1x Slave
Modem 3G / 4G, GPS (optional); Micro Sim Socket
RS-232 1x RS-232 (RX/TX/CTS/RTS) and 1x RX, TX
Synchronous Serial Interfaces SPI up to 2 chip selects; Pinning for RFID-I / F (Karl³)
BLE Modul (Option) Single Mode BLE V 4.0 Slave
INSIKA (Option) Socket for optional Smart-Card Interface (Plug In)
Misc. 2x Service Button
Video
Video output HDMI 1.4 Type C Connector; + On / Off, PWM 2nd Backlight control con.
Audio
Speaker output 1x speaker (connector), 1.5 W RMS (8Ω)
Micro IN 1x microphone connector
Display and Touch
Display Interface Dual Channel 24bpp LVDS
Sensor Ambient-Light-Sensor (external via I²C)
Touch Interface PCAP I²C
Backlight Interface +12 V, +5V, on/off, PWM
Device Dimensions
W x H x D 160 x 18 x 95 mm; PCB 160 x 95 mm
Weight 115 g
Power Supply
Supply Voltage Nom. 24 V DC / max. 10 to 42 V DC
Consumption Typ. 3.0 W; max. tbd.
Li-Ion-Akku 3.7 V / 2.0 to 4.0 Ah for Modem and Backup-Power
Charge Controller Internal
Typical Environmental Conditions
Storage Temp. -20 to +70 °C without Li-Ion-Akku
Operating Temp. 0 to +40 °C (normal operation) -20 to +60 °C without charge Li-Ion-Akku
Humidity 5 to 90 % RH
Max. Operating Altitude ty 3.000 m
Max. Storage/Transit Altitude 10.000 m
Noise Level [db(A)] @ 1m <<40 (fanless design)
Lifetime
MTBF ≥ 50.000 h
PRODUCT MANUAL
SANTVEND core
4. Technical Data
9
PRODUCT MANUAL
SANTVEND core
4.1 Block Diagram
10
1x Speaker
2-pole JST Audio
Amplifier
Block Diagram SANTVEND
i.MX6
Backlight
12-pole Molex
USB-Host
USBA
I²C-3
DRAM DDR3L
Audio
Codec
FlexCAN-1
AUD3
SPI-1
eMMC
24 V DC
2-pole Modex Step Down
Converter
PMIC Power
Ambient-Light
5-pole JST
SD-Card
Connector
CAN
6-pole Molex
LVDS0
LVDS1
2x Display LVDS
20-pole Hirose
GPIO
PWM1_OUT
HDMI
HDMI
Type C
2x RS-232
10-pole Molex
RS-232
Transceiver UART-2,3
UART-4,5
Cap.Touch
6-pole JST
BLE-Modul
RJ-45
Jack
Ethernet
Phy
MDIO/RMII
UART-3
IC-1
GPIO
USDHC2
SPI-3
USDHC4
RTC
Super-
Cap
IC-1
CAN
Transc.
8-pole JST
USB OTG
Cap.Touch
7-pole JST
Charger
Akku
3-pole
JST
MDB (M/S)
12-pole Molex
MDBTran-
sceiver
Micro
2-pole JST
RFID-I / F
(Karl³)
Antenne
MMCX
Modem
3G-4G
UART 1
USB H1
GPIO
PWM2_OUT
BL-Control
GPS MMCX
Socket
INSIKA
PRODUCT MANUAL
SANTVEND core
4.2 Technical Drawing
6x
2,7
160
156,5
102,9
3,5
15
101
3,5
91,5
95
5,8
19
15,5
3,5
SANTVEND core
Missing dimensions according to 3D CAD files
11
Pos. Description
1GPS (X1703)
2GSM (X1700)
3MDB (X1500)
4Power (X200)
5 RS-232 (X1401)
6Speaker (X1301)
7Microphone (X1300)
8CAN (X1400)
9Ethernet (X1200)
10 USB - Host (X900)
11 Boot Select (SW600)
12 Reset (SW601)
13 Service 1 (SW1600)
Pos. Description
14 Service 2 (SW1601)
15 Micro SD card reader (X800)
16 JTAG - Debug Interface (X600)
17 HDMI (X704)
18 LVDS 1 (X700)
19 INSIKA (X1800)
20 2nd BL-CTRL (X703)
21 Backlight & PWM (X705)
22 Ambient Light Sensor (X904)
23 Touch, 3.3 Vcc (X907)
24 Touch, 5.0 Vcc (X902)
25 Li - Ion - Akku (X201)
26 Micro SIM - Card (X1702)
PRODUCT MANUAL
SANTVEND core
4.3 PCB Design and Pin Assembly
As this manual describes a core version, the internal and external interfaces will be mentioned in the following
chapter.
(Exemplary Illustration front side. The illustration shows the fully equipped SANTVEND Quadcore light. It shows no
heatsink to provide a better overview.)
12
Pos. Description
27 LVDS 2 (X701)
28 Ambient - Light - Sensor (X905)
29 SPI (X1600)
PRODUCT MANUAL
SANTVEND core
(Exemplary Illustration back side)
13
X701
X905 X1600
Pos. Description
1
DC in
2
RS-232
3
Ethernet
4
USB-Host
Exemplary Illustration
PRODUCT MANUAL
SANTVEND core
5. Installation and Start Up
The content of this document is limited to explain the device connectors and how to access SANTVEND via FTP
over your local area network (LAN) within a few seconds. For advanced hardware specications and software
support, please refer to chapter „3.2 Related Documents and Online Support“
5.1 Connection Scheme
http://support.garz-fricke.com/projects/Santvend/
14
Ethernet (TCP/IP) via
cross over cable or switch
USB Accessory
Memory stick,
mouse
RS-232 (Serial)
Debug-PC /
Periphery
2x RS232 Speaker??? ?????? CAN/RS485 Digital I/O
Power LAN
USB-Host
Pin Name Description Level
Center RF-IN 50 Ohm; Feeding active GPS antenna +3,3V
Shield GND
Header: MMCX_SMD_EdgeMount 090°
Pin Name Description Level
Center RF-I/O 50 Ohm; GSM antenna
Shield GND
Header: MMCX_SMD_EdgeMount 090°
PRODUCT MANUAL
SANTVEND core
6. Internal and External Interfaces
6.1 Antenna GPS (X1703)
6.2 Antenna GSM (X1700)
Application Notes
The usage of a Quad Band Antenna (850/900/1800/1900), VSWR: ≤ 2.0 is recommended
For cabled aerials, the cable length should not exceed 3 m (dedicated cable type RG174)
For larger cable length not exceeding 30 m, the usage of a special low loss cable is essential.
Additional cable adapters are needed to contact the low loss cable properly.
Outdoor aerials have to be designed and grounded according to DIN EN 60728-11
The grounding of the antenna is not obliged, when the antenna is installed
more than 2 m below the roof edge and
less than 1.5 m away from the building
For installation in countries outside Germany, please ensure to act in accordance with the local
restrictions and regulations!
15
Pin Name Description Level
1VCC_MDB-S Eingang VCC (complete system) 12-24 VDC
2GND Common GND GND
3WakeUp-MDB-S WakeUp-IO (In/Open Collector) 5V
4TX-MDB-S OUT TX MDB Slave 5V
5RX-MDB-S IN RX MDB Slave 5V
6GND Common GND GND
7VCC_MDB-M Ausgang VCC MDB Master 12-24 VDC
8GND Common GND GND
9WakeUp-MDB-M WakeUp-IO (In/Open Collector) 5V
10 RX-MDB-M IN RX MDB Master 5V
11 TX-MDB-M OUT TX MDB Master 5V
12 GND Common GND GND
Header: Type 43045-1200 / 12 pol. Molex MicroFit 090°
Plug: 43025-1200 12 pol. Molex MicroFit
crimp contact Molex 43030-0007
PRODUCT MANUAL
SANTVEND core
6.3 MDB (X1500)
16
1
7
Pin Name Description Level
1GND Common GND GND
2Power In Eingang VCC (complete system) Nom. 12 to 24 V DC
Header: Molex 43045-0200 Micro-Fit 2p
Plug: Molex 43025-0200 Micro-Fit 2p,
crimp contact Molex 43030-0007
PRODUCT MANUAL
SANTVEND core
6.4 Power (X200)
Caution:
Power supplies connected to this device must be compliant to the requirements of
“limited power sources” (LPS) to prevent the end-user from danger in case of a fault.
17
1
PRODUCT MANUAL
SANTVEND core
Electrical characteristics
Nominal voltage 3,7 V
Nominal capacity (minimum requirement) 2 Ah
Initial Internal Impedance Less than 100mΩ
NTC 10KOhm 10% @25°C
Operating conditions
Operating Temperature Charge : 0 .. +40 °C
Discharge : -20 .. +60 °C
Charge System Constant current: 0,2 .. 1,0 C
Constant voltage: 4,2 V
Maximum continuous discharge current 1,0 .. 2,0 C
Pulse discharge current 2,0 .. 4.0 C
Safety Requirements
Protection Circuit See schematic, wiring diagram
Over Voltage Cut OFF 4.3 V
Under Voltage Cut OFF 2.25 V
Overload Cut OFF (Short circuit protection) Reversible fuse
NTC Built in (10K)
Approval & Conformity UL, CE
Pin Name Description Level
1GND Common GND GND
2NTC 10K NTC 3.3 V
3V Li Ion Akku Plus Li-Ion-Akku 4.2 V
Header: Type: B3B-XH-A / 3pol. JST-XH, THT 180°
Plug: XHP-3 / 3pol. JST-XH
crimp contact SXH-001T-P0.6 (22-28 AWG Tin)
3RO\IXVH 17&
3OXV
7HPSB6HQVH
0LQXV*1'
3URWHFWLRQ&LUXLW
3
;+3
/LWKLXP,RQ%DWWHU\3DFN
6.5 Li - Ion - Akku (X201)
Recommendation for an suitable Li-Ion-Accumulator
Schematic, wiring diagramm
18
Pin Name Description Level
1GND Common GND GND
2RS232-1_TX RS232-1_TX V.28
3RS232-1_RX RS232-1_RX V.28
4RS232-1_RTS RS232-1_RTS V.28
5RS232-1_CTS RS232-1_CTS V.28
6GND Common GND GND
7RS232-2_TX RS232-2_TX 1V.28
8RS232-2_RX RS232-2_RX 1V.28
9MISC_WU WakeUp-IO (In/Open Collector) 5 V
10 GND Common GND GND
Header: Type 43045-1000 / 10pol. Molex MicroFit 090°
Plug: 43025-1000 / 10 pol. Molex MicroFit
crimp contact Molex 43030-0007
PRODUCT MANUAL
SANTVEND core
6.6 RS-232 (X1401)
1 Note: Not available if INSIKA-Interface populated.
19
1
6
Pin Name Description Level
1GND Common GND GND
2MIC_IN MIC & MIC_BIAS 3.3 V
Header: Type SM02B-SURS-TF / 2pol. RM 0.8mm; JST SUR-Serie 090°
Plug: Type 02SUR-32S / 2pol. RM 0.8mm; JST SUR-Serie
(2 Position Rectangular Receptacle Connector IDC Tin 32 AWG)
Pin Name Description Level
1Speaker+ OUT D-Class-Amp. 5 V
2Speaker- OUT D-Class-Amp. 5 V
Header: Type S2B-PH-SM3-TB / 2pol. RM2.0mm; JST PH-Serie 090°
Plug: Type PHR-2 / 2pol. RM2.0mm; JST PH-Serie
crimp contact JST SPH-002T-P0.5L
PRODUCT MANUAL
SANTVEND core
6.7 Speaker (X1301)
6.8 Microphone (X1300)
20
1
1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35

Seco SBC-SANTVEND-MX6 Owner's manual

Brand
Seco
Model
SBC-SANTVEND-MX6
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents