Terma grzejnika Voltan User guide

VOLTAN

Smart Wi-Fi Radiator

Installaon and Basic Rules for Use.

Montáž a základní pravidla použi.Montáž a základní pravidla použi.

Montage und grundsätzliche Verwendung.Montage und grundsätzliche Verwendung.

Installaon et règles d’ulisaon de base.Installaon et règles d’ulisaon de base.

Montaż i podstawowe zasady użytkowania.Montaż i podstawowe zasady użytkowania.

Монтаж и основные правила использования.Монтаж и основные правила использования.

PLEN CS DE FR RU

2

SAFE INSTALLATION

1. The device should be installed by a qualied installer

in accordance with all applicable safety regulaons

and other regulaons.

2. All installaons to which the device is connected

should comply with the relevant regulaons in force

in a given area.

3. The radiator is intended for heang dry rooms. The

distances shown in the illustraon below, must be

strictly adhered to during installaon.

A - min. 15 cm

B - min. 10 cm

C - min. 50 cm

D - min. 50 cm

3

EN

4. The circuit in the electrical installaon to which the radiator is connected

must have an appropriate over-current switch and a residual-current device

(R.C.D.) with a sensivity of 30 mA.

5. In a wet room installaon is only possible at the locaon and as described in

the IEC 60364-7-701 standard.

6. Do not use extension cords or socket adapters to power the radiator.

7. The place where the radiator is connected to the electrical system must not

be behind or directly above the radiator

8. Before connecng the radiator to the power supply, make sure the power

cord is not mechanically damaged. In case of damage, immediately contact

the seller or the manufacturer.

9. The device is made in protecon class II.

10. When connecng the device permanently to the installaon, observe the

following guidelines:

a. brown conductor – connecon to the phase circuit (L).

b. blue wire – connecon to the neutral circuit (N).

11. Make sure the radiator has been installed on the wall in accordance with the

installaon instrucons (included in the mounng kit).

12. Make sure that the power cord does not come into contact with the hot

OK

4

parts of the radiator.

13. The power must be o during installaon or removal of the device.

14. The interior of the device must not be tampered with.

15. This informaon material should be handed over to the end user of the

radiator.

SAFE USE

CAUTION: Some parts of the radiator can be very hot

and can cause burns. Parcular aenon should be paid

in the presence of children or disabled people.

1. The electric radiator is not a toy. Children under 3 years of

age without proper supervision should not be in the imme-

diate vicinity of the radiator.

2. Children from 3 to 8 years of age and people with redu-

ced mental or physical ability may only operate the radia-

tor when it is properly installed and connected, and the

children are supervised or have been taught how to use it

safely and understand the hazards arising from use.

5

EN

3. Do not cover the radiator or otherwise block the top or



4. The device is intended for home use.

5. Regularly check that the device is not damaged and that it is safe to use.

6. If the power cord is damaged, the device cannot be used. Disconnect the

device from the mains and contact the manufacturer or distributor.

7. Do not ood the radiator control module. Protect the device against foreign

objects geng inside e.g. wire, paper etc.

8. Do not open the housing.

9. Use the device only for its intended use as described in the instrucon

manual.

10. Cleaning may only be performed aer disconnecng the device from the

mains.

11. Cleaning the device by children under 8 years of age is allowed only under

proper supervision.

6

MAINTENANCE

Before performing maintenance acvies, always disconnect the device from

the mains.

Clean the product only with a dry cloth or a damp cloth with a lile detergent

without the use of solvents or abrasives.

TECHNICAL DATA

Model designaon

(power cable type)

PB (Straight cable without plug)*

PW (Straight cable with plug)

Power supply 230V/50Hz

Device protecon class Class II

IP code*** IPx4

Power range: [W] ** 1000, 2000 [W]

* device intended for permanent connecon to the mains

** the device data is given on the nameplate label

*** IP code species the degree of protecon provided by enclosure

INTENDED USE

The Terma VOLTAN Smart Wi-Fi convector radiator is an electric heating

device designed for heang closed rooms. You can control the device by means

of the buons on the control panel or remotely with the Terma Smart Wi-Fi

applicaon. The radiator can work alone or in combinaon with other Terma

SMART Wi-Fi devices, such as the temperature and humidity sensor and the

window opening sensor.

7

EN

USER MANUAL

DESCRIPTION OF THE SMART SYSTEM

Terma Terma Smart Wi-Fi is an intelligent heang system, all elements of

which communicate using Wi-Fi technology. In addion to the standard ope-

raon, i.e. maintaining the set air temperature in the rooms, the user can

control the system using the Terma SMART mobile applicaon. Thanks to this

applicaon, it is possible to program seven-day schedules, iniate an early

start mode, and divide the heated area into heang zones (several other un-

cons are also included).

VEO

electric heang element

VAZ

thermostac head

VOS

window opening

sensor

VTS

temperature and

humidity sensor

Wi-Fi router

cloud service

mobile applicaon

VOLTAN

electric convector

8

NOTE:

For the inial set-up and registraon of the devices, a router with Internet

access is required (provided by the system user). A Wi-Fi router is responsible

for delivering a wireless signal to each of the system components

Further informaon can be found in the chapter — SMART System — informaon

about the system and applicaon, as well as on the website www.termasmart.com

Each of the devices can funcon independently, however, the recommended

structure of the system consists of heang zones, e.g. individual rooms in the

house, which may include one (as a maximum) VTS temperature sensor per

room and any number of other types of devices and sensors. Terma SMART

Wi-Fi heang devices will funcon at an opmum level when connected per-

manently to a local Wi-Fi network with Internet access.

The devices will also funcon without access to the Internet, or even without

a Wi-Fi connecon, but in this case the previously loaded schedule will be

implemented, and many of the device funcons will remain unavailable.

STARTING THE VOLTAN RADIATOR

1. Install the SMART applicaon on your mobile device, grant the appropriate

approvals relang to the locaon and operaon of the scanner.

2. Create a user account and provide basic details of the newly created ʻhouse’.

3. Prepare a password for the local Wi-Fi network.

4. Turn on the radiator and start PAIRING:

9

EN

a. The new device can be started with a short press on either of the „+” or

„−” buons on the front panel.

b. If the pairing mode does not start automacally, or if the device is re-

started, press both buons „+” and „−” simultaneously and hold them for

approx. 15 seconds (the enre display ashes every 5 seconds, aer the

third ash, release the buons).

NOTE: from now on, the device broadcasts its network address (signal) and

is seen by the SMART applicaon.

c. Launch the SMART applicaon and go to the Devices screen.

d. Select the „+” buon and follow the instrucons in the applicaon (rst

scan the code from the scker on the device or enter it manually, select

the local Wi-Fi network and enter the router password, then from the

list of available devices, select the device currently being added. Finally,

conrm your Wi-Fi network).

All LED strips will ash three mes and the. „+” and „−”

buons will ash steadily, the device will go into PAIRING

MODE for 5 minutes.

All LED strips will ash 3 mes and the „+” and „−” buons

will start ashing steadily, the device will go into PAIRING

MODE for 5 minutes.).

ON/OFF

10

e. When the automac part of the process is over, select the appropriate

zone in the applicaon (or create a new one) and enter the device name

and other data.

OPERATING THE INTERFACE PANEL

1. To wake up the device from the sleep mode, briey press any buon.

2. To raise or lower the temperature by one step, briey press „+” or „−” buon.

3. To start the INTENSIVE HEATING funcon, press and hold the „+” buon

„−” a red stripe will appear on the interface. The radiator will heat at full po-

wer for 1 hour and then return to the previous sengs

4. To swap the „+” and „−”, buons, press and hold (> 10 s) the „+” buon.

5. Modes and special acons — press and hold both „+” / „−” buons

simultaneously:

LED strips

control keys

Red stripe

White stripes 5 stripes 26°C

4 stripes 24°C

3 stripes 21°C

2 stripes 18°C

1 stripe 15°C

Red stripe INTENSIVE HEATING funcon is on

11

EN

a. for 5 s — the heater turns o (single ash on the interface);

b. for 10 s — the heater will be put to sleep(stand-by) mode (single ash on

the interface).

c. for 15 s — enter pairing mode (AP), the enre interface will ash 3 mes;

d. for 25 s — restore factory sengs and start the pairing mode, the device

will ash as it did at set-up;

6. If the panel of the device has been blocked (the PARENTAL CONTROL

funcon in the control applicaon), pressing the „+” key for 5 seconds will

release the lock for 1 minute, which will allow you to change the sengs

manually on the device without the need to use the applicaon (conrmaon

by ashing interface). The change made on the device manually is valid unl

the next automac temperature change saved in the schedule.

ADDITIONAL COMMENTS ON ADDING

DEVICES TO THE TERMA SMART SYSTEM

• Adding devices is possible only via the mobile applicaon.

• System changes are sent locally by the router, and to the cloud service by

the applicaon.

• In some Android system overlays, during pairing, the phone tries to automa-

cally switch to the remembered Wi-Fi network with Internet access — you

must manually conrm the connecon with the device’s network.

• Aer adding the heang devices to the system, they are turned o by

default (they do not heat up, despite the low ambient temperature, the inter-

face bars are not lit, and the remote communicaon interval is 1 h).

• Heang devices should be added rst, followed by the sensors.

12

• There can be only one temperature and humidity sensor (VTS) in one heang zone.

• The name of each device must be unique within the system.

• The name of the zone must be unique within the system.

SMART SYSTEM

BASIC INFORMATION ABOUT THE SYSTEM

AND THE APPLICATION



In the applicaon, a newly created ʻhouse’ should be divided into heang zones

(e.g. rooms) to which individual devices are assigned. It is possible to select

a schedule and view telemetry data for each zone. The list of all zones is visible

to the user in the Zones tab. The view of a single zone contains a set of acons

and informaon available to the user.

The temperature presented in the center of the screen of a single zone is the

current measured temperature, while the value at the boom is the set tem-

perature that depends on the mode in which the system is currently operang:

• if the Vacaon mode is acve, the Vacaon mode temperature is displayed

• if the Smart Locaon is acve, the temperature for the Smart Locaon is

displayed

• if at least one device is in the manual mode, the temperature set for the

manual mode is displayed — the icon is displayed.

• otherwise, the temperature for a given me interval will be displayed accor-

ding to the schedule — icon is displayed.

13

EN

Principles of measuring the temperature in the room (in the zone):

• If there is a temperature and humidity sensor (VTS) in a zone, its indicaons

are the basis for the temperature control for all devices in a given zone (re-

commended conguraon);

• If there is no VTS sensor in the zone, the devices will operate based on the

average of the sensor readings of all devices in that zone (or one sensor if

one device is in the zone).

A more detailed descripon can be found on www.termasmart.com

WARRANTY

1. The subject of this warranty is an electric convector radiator with characteri-

scs specied on the nameplate label.

2. The aached instrucon manual is an integral element of the warranty. It is

necessary to read it carefully prior to the use of the product.

3. By accepng the device on purchase, the Client conrms that the product

is of full value. The Client should immediately inform the Seller of any disco

vered faults — otherwise it will be understood that the Product was faultless

at the me of purchase (this refers in parcular to the quality of the radiator

surface).

4. The warranty period for the product is 24 months from the date of purchase.

5. The proof of purchase constutes the basis for warranty claims. Lack of the

proof of purchase allows the Manufacturer to reject a warranty claim.

6. This warranty does not cover any faults and/or damages:

a. caused by incorrect installaon (not in accordance with the manual),

b. resulng from the use of the radiator contrary to the requirements of the

aached instrucon manual or as a result of self-made repairs,

c. caused by the Client aer receipt from the Seller.

7. The warranty does not cover claims related to the radiator’s technical and

14

operaonal features, as long as they comply with those specied in the in

strucon manual and technical specicaon.

8. The warranty repair does not include acvies described in the instrucon

manual, which should be performed by the user within his own scope and

at his own expense.

9. If the complaint is accepted, the Manufacturer undertakes to remove the

defect. If the repair is impossible, the Manufacturer shall replace the product

with a new one.

10. If the product is replaced with a new one, the warranty period runs anew.

11. The claim shall be considered within 14 calendar days. The date of repair

shall be agreed with the Client individually.

12. In the event of nocing any malfuncon in the operaon of the radiator

or any other damage covered by the warranty, please contact the Seller

immediately.

TREATMENT OF ELECTRICAL AND

ELECTRONIC EQUIPMENT WASTE:

Pursuant to the regulaons in force for used electric and electronic equipment,

products marked with the symbol of separate collecon cannot be placed with

other municipal waste. Due to the content of harmful substances, electronic

products not subjected to the selecve sorng process may be dangerous to

the natural environment and to human health. The correct separate collecon

of used electrical and electronic equipment prevents negave impacts on the

environment.

Informaon concerning the waste collecon system for electrical and electro-

nic equipment.

• distributor accepts and collects electrical and electronic equipment waste

from households free of charge, provided that the equipment is of the same

type and performs the same funcons as the equipment purchased,

• a collecng operator have the right to refuse to accept the waste equipment

if it poses a threat to the health or life of individuals receiving the equipment

due to contaminaon,

15

EN

• the user of equipment intended for households may hand over the used

equipment to:

— a distributor,

— a waste processing plant,

— collecng municipal waste in the commune.

16



1. Zařízení by měl instalovat kvalikovaný technik

v souladu se všemi platnými bezpečnostními předpisy

a dalšími předpisy.

2. Všechny instalace, ke kterým je zařízení připojeno, -

musí být v souladu s příslušnými předpisy platnými

v dané zemi.

3. Topidlo je určeno pro vytápění suchých místnos. Při

montáži je třeba bezpodmínečně dodržet vzdálenos

uvedené

A - min. 15 cm

B - min. 10 cm

C - min. 50 cm

D - min. 50 cm

17

CS

4. Je třeba zajist, aby obvod v elektrickém systému, ke kterému je - k ohřívači

připojen, měl správný spínací nadproudový a proudový chránič (RCD) s citli-

vos 30 mA.

5. Ve vlhkých místnostech je instalace možná pouze na místě a jak je popsáno

v IEC 60364-7-701.

6. K napájení přímotopu nepoužívejte prodlužovací kabely ani zásuvkové

adaptéry.

7. Místo připojení ohřívače k elektrické sí nesmí být za ohřívačem ani přímo

nad ním

8. Před připojením ohřívače k elektrické sí zkontrolujte, zda není přívodní ka-

bel mechanicky poškozen. V případě poškození ihned kontaktujte prodejce

nebo výrobce.

9. Zařízení je vyrobeno v ochranné třídě II.

10. Při trvalém připojení zařízení k instalaci dodržujte následující pokyny:

a. Hnědý vodič - připojení k fázovému obvodu (L),

b. Modrý vodič - připojení k nulovému obvodu (N).

11. Ujistěte se, že ohřívač byl nainstalován na stěnu v souladu s Montážním

návodem (součás balení montážní sada).

12. Dbejte na to, aby se napájecí kabel nedostal do kontaktu s horkými prvky

ohřívače.

OK

18

13. Zařízení nesmí být při montáži nebo demontáži pod napěm.

14. S vnitřkem zařízení nesmí být manipulováno.

15. Tento informační materiál by měl být předán koncovému uživateli.



POZNÁMKA: Některé čás přímotopu mohou být velmi

horké a mohou způsobit popáleniny. Zvláštní pozornost

by měla být věnována přítomnos dě nebo posžených

osob.

1. Elektrický ohřívač není hračka. Dětem do 3 let bez dozoru

– by nemělo být dovoleno být v přímé blízkos topidla.

2. Dě ve věku od 3 do 8 let věku a osoby se sníženou

duševní či fyzickou poruchou mohou ovládat topení pouze

v případě, že je správně nainstalován a připojen, a dě jsou

pod dohledem nebo byli vyškoleni, aby ovládaly bezpečně

a rozuměli rizikům použi.

19

CS

3.



4. Zařízení je určeno pro domácí použi.

5. Pravidelně kontrolujte, zda není zařízení poškozeno a zda je bezpečné jej

používat.

6. Pokud je napájecí kabel poškozen, zařízení nelze používat. Odpojte napájení

a kontaktujte výrobce nebo distributora.

7. Nezaplavujte vodou řídicí modul topení. Chraňte zařízení před cizími

předměty, jako je drát, papír atd.

8. Neotevírejte opláštění.

9. Používejte zařízení pouze k určenému účelu popsanému v návodu.

10. Čištění lze provádět pouze po odpojení zařízení od sítě.

11. Čištění zařízení dětmi do 8 let je povoleno pouze pod řádným dohledem.

20



Před prováděním údržby vždy odpojte zařízení od sítě. Výrobek čistěte pouze

suchým nebo vlhkým hadříkem s trochou čiscího prostředku bez použi roz-

pouštědel nebo abrazivních látek.



Označení modelu

(typ napájecího kabelu)

PB (přímý kabel bez zástrčky)*

PW (přímý kabel se zástrčkou)

Napájení 230V/50Hz

Třída zařízení Klasa II

IP označení *** IPx4

Dostupné výkony [W] ** 1000, 2000 [W]

* Zařízení určené k trvalému připojení k elektrické sí

** Údaje o zařízení jsou uvedeny na typovém štku

*** Označení IP označuje stupeň zabezpečení, který poskytuje kryt zařízení



Grzejnik Wi-Fi konvekční ohřívač Terma VOLTAN SMART je elektrické topné

zařízení určené k vytápění uzavřených místnos. K ovládání zařízení můžete

použít tlačítka na zařízení nebo vzdálenou aplikaci Terma Smart Wi-Fi. Zářič

může pracovat samostatně nebo v kombinaci s dalšími zařízeními Terma SMART

Wi-Fi, jako je čidlo teploty a vlhkos a čidlo otevření okna.

Page is loading ...

Terma grzejnika Voltan User guide

This manual is also suitable for

Terma grzejnika Voltan User guide

in other languages

Related papers

Other documents