ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service: www.twinstarhome.com
in English Call: 866-661-1218
in Spanish Call: 866-661-1218
in French Call: 866-374-9203
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS,
ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER
ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente: www.twinstarhome.com
Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en español: 866-661-1218
Línea para llamadas en francés: 866-374-9203
STOP
STOP
PARE
PARE
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE
SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle : www.twinstarhome.com
pour le service en anglais, composez le 866-661-1218
pour le service en espagnol, composez le 866-661-1218
pour le service en français, composez le 866-374-9203
ARRÊT
ARRÊT
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
WOOD MANTEL ASSEMBLY INSTRUCTIONS
WOOD FIREPLACE MANTEL
23MM070
E-1
Part Description Quantity
PARTS
HARDWARE
PARTS LIST
E-mail: www.twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
For Customer Service:
A
B
C
D
E
F
G
EE
FF
GG
I
J
K
P
R
U
W
Y
L
M
N
O
Q
V
S
T
Z
Hearth/Base
Center Left Side Panel
Center Right Side Panel
Center Front Panel
Center Shelf
Left Side Panel
Right Side Panel
Front Molding Top
Front Molding Left
Front Molding Right
Mantel/Top
Left Back Panel
Right Back Panel
Center Back Panel
Left Front Door
Right Front Door
Wood Shelf
Insert Support Bar
Bolt 1/4 in. x 1-1/4 in.
Washer 1/4
Wood Dowel
Shelf Pin
Screw
Knob (With Bolt)
Molding Brackets
Small Wood Screw
Touch-Up Pen
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
32+1 extra
32+1 extra
32+1 extra
8
43
2
2
10
1
33445
Vietnam
Vietnam
For a complete tight fit every bolt
should have a flat washer.
All panels are labeled Left and Right as viewed
from the front of unit.
1. Locate the Center Left Side Panel (B), Center
Right Side Panel (C), Center Front Panel (D), and
set out face down on a scratch-free surface.
2. Insert one Wood Dowel (N) into each of the
pre-drilled holes.
3. Push the Center Left Side Panel and Center Right
Side Panel snug to the Center Front Panel. Make
sure the Wood Dowels are seated in the pre-drilled
holes.Connect the Center Left Side Panel (B),
Center Right Side Panel (C) and Center Front
Panel (D) with Connection Plate, tighten
Screws (T) through the pre-drilled holes.
E-2
PLEASE READ AND FOLLOW ALL SAFETY TIPS
Center
Front Panel
Center
Left Side
Panel
B
C
D
T
N
N
Center
Right Side
Panel
Connection
Plate
GETTING STARTED
1. Before assembly, CAREFULLY use scissors or utility knife to cut and unwrap all parts. Make sure
you do not discard the hardware.
HELPFUL HINTS
6RPHVWHSVDUHPRUHHDVLO\KDQGOHGZLWKWZRDGXOWV
Attach the fireplace insert to the completed wood mantel last. INSTALL INSERT IN FROM THE
BACK OF THE FIREPLACE SO AS NOT TO SCRATCH THE HEARTH/BASE.
8VHFDUHLQDVVHPEOLQJ\RXUQHZfireplace, take your time and use the hardware provided and a
quality Phillips head screwdriver. NEVER OVER TIGHTEN BOLTS.
CARE & CLEANING
1. Dust your fireplace regularly with a soft non-lint producing cloth or household dusting product.
2. You can clean your fireplace with a gentle non-abrasive household cleaner. Make sure to dry your
fireplace immediately with a soft cloth or towel.
2. Make sure that you have all the parts listed. If you are missing any parts please email Customer
Service: www.twinstarhome.com or call 1-866-661-1218 in English, 1-866-374-9203 in French
or 1-866-661-1218 in Spanish. Please identify the parts you need and model number. Make sure
to include your name and address.
'RQRWVLWRQDQ\SDUWRIWKHPDQWHO
CAUTION:
DO NOT MOVE MANTEL OR INSERT WHILE PLUGGED INTO POWER SUPPLY.
9. Insert one Wood Dowel (N) into each of
pre-drilled holes.Push the Right Side
Panel (G) and Left Side Panel (F) snug to
completed assembly from step 8. Using
Bolts (L) and Washers (M) through the
pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Completed Assembly
Hearth/Base
Completed Assembly
Right
Side
Panel
Left
Side
Panel
N
N
N
N
N
N
N
M
L
M
L
M
L
G
F
7. Insert one Wood Dowel (N) into each of
the pre-drilled holes.
8. Then locate Center Shelf (E) and lay
finished side up on top of Completed
Assembly from step 6. From the inside,
attach the Center Shelf using Bolts (L)
and Washers (M) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.
Center Shelf
E
A
B
C
N
N
N
N
N
N
N
N
M
L
M
L
E-4
Mantel/Top
M
L
N
N
N
N
I
N
S
T
Molding
Bracket
Front Molding
Top
Front
Molding
Right
Front
Molding
Left
Small
Wood
Screw
L
M
N
EE
FF
GG
N
N
Completed Assembly
12. Insert one Wood Dowel (N) into each of
the pre-drilled holes on the top edges of
the Assembly from step 11. Then locate
Mantel/Top (I) and lay finished side up
on top of completed assembly. From the
inside, attach the Mantel using Bolts (L)
and Washers (M) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.
11.
10.
10
Locate the three front molding pieces
( EE,FF,GG) and four dowels.With the
three molding pieces face down on a
clean smooth flat surface.Insert dowels
into the two holes on the side molding
pieces (FF,GG). Carefully slide the left
(FF) and right (GG) side molding pieces
into place using the dowels. Locate flat
metal bracket (S) and place into spaces
in back of molding pieces.Attach bracket
to molding pieces using small wood
screws (T).
CAREFUL NOT TO OVER TIGHTEN.
13.Using Phillips head screwdriver tighten
all Bolts alternating top and bottom, left
and right.
E-5
15. Locate Right Front Door (U) and Left Front
Door (R). Slide door hinge keyhole into
panel hinge bracket. (Diagram 1)
Use Phillips Head Screwdriver to tighten
screws. (Diagram 2)
TO ADJUST HINGES
To adjust door forward or backward change
keyhole slot position.
(As Shown In Diagram 3a)
To adjust door right or left loosen/tighten
screw. (As Shown In Diagram 3b)
To adjust door up or down adjust bracket
height. (As Shown In Diagram 3c)
14. Locate Left Back Panel (J), Right Back
Panel (K) and Center Back Panel (P),
attach to the back of the completed
assembly from step 13. Use a Phillips
Head screw driver, tighten screws (Q)
through the pre-drilled holes in the Back
Panels to the completed assembly.
P
Left
Back
Panel
Right
Back
Panel
K
J
Center Back Panel
Screw
Q
J
R
U
Left
Front
Door
Right
Front
Door
3
2
3a
3b
3c
1
E-6
Completed Unit
Electric
Fireplace Insert
Install
Insert
From
Back
Twin-Star International, Inc.
Delray Beach, FL 33445
In English: 1-866-661-1218
In French: 1-866-374-9203
In Spanish: 1-866-661-1218
Model# 23MM070
Made in Vietnam
Printed in Vietnam
© 2011, Twin-Star International, Inc.
W
W
U
V
V
R
18. Lift insert carefully into the back of the
unit and center in the insert opening. Do
not dr ag insert across Hearth/Base (A)
as it may scratch your unit.
PLEASE READ ALL “ELECTRIC
FIREPLACE INSERT”
INSTRUCTIONS PRIOR TO
INSTALLING ELECTRIC INSERT
IN YOUR COMPLETED
FIREPLACE MANTEL. INSTALL
THE INSERT IN YOUR
FIREPLACE CLOSE TO ITS
FINAL POSITION.
MOVE YOUR COMPLETED UNIT
ONLY SHORT DISTANCES.
MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO
PEOPLE TO MOVE COMPLETED
UNIT INTO ITS FINAL POSITION.
Connect the Insert Support Bar (Y) to the
inside Left and Right panels, using the
Bolts (L) and Washers (M) through
pre-drilled holes.
19.
M
Y
L
Insert
Support Bar
Wood
Shelf
Wood
Shelf
16. Attach the Knob (V) to the Left Front
Door (R) and Right Front Door (U),
use the bolts attached through the
pre-drilled holes in the doors. Then
use a Phillips Head Screwdriver to
tighten the bolts.
17. Choose desired height of Shelf (W)
and place the four Shelf Pin (O) into
same height shelf holes inside side
Panels. Insert Wood Shelf (W), allow
Wood Shelf (W) to rest on the Shelf
Pin (O).
Left
Front
Door
Right
Front
Door
O
Pin
Shelf
Konb
(With Bolt)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
