Sony HT-K170 User manual

1

GB

4-230-316-12(1)

Home Theater

System

HT-K170

GB

FR

NL

SE

Operating instructions

Mode d’emploi

Gebruiksaanwijzing

Bruksanvisning

Getting Started

2

GB

WARNING

To prevent fire or shock

hazard, do not expose

the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to qualified

personnel only.

Precautions

On safety

• Should any solid object or liquid fall

into the cabinet, unplug the amplifier

and have it checked by qualified

personnel before operating it any

further.

On power sources

• Before operating the amplifier, check

that the operating voltage is identical

with your local power supply. The

operating voltage is indicated on the

nameplate at the rear of the amplifier.

• The amplifier is not disconnected

from the AC power source (mains) as

long as it is connected to the wall

outlet, even if the amplifier itself has

been turned off.

• If you are not going to use the

amplifier for a long time, be sure to

disconnect the amplifier from the

wall outlet. To disconnect the mains

lead, grasp the plug itself; never pull

the cord.

• The AC power cord (mains lead)

must be changed, at a qualified

service shop only.

• The mains switch is located on the

front exterior.

On placement

• Do not install the appliance in a

confined space, such as a bookcase or

built in cabinet.

• Place the amplifier in a location with

adequate ventilation to prevent heat

buildup and prolong the life of the

amplifier.

• Do not place the amplifier near heat

sources, or in a place subject to direct

sunlight, excessive dust or

mechanical shock.

• Do not place anything on top of the

cabinet that might block the

ventilation holes and cause

malfunctions.

• Do not set the speakers in an inclined

position.

• Do not place the speakers in locations

that are:

– Extremely hot or cold

– Dusty or dirty

– Very humid

– Subject to vibrations

– Subject to direct sunlight

On operation

• Before connecting other components,

be sure to turn off and unplug the

amplifier.

• Do not drive the speaker system with

a continuous wattage exceeding the

maximum input power of the system.

• If the polarity of the speaker

connections are not correct, the bass

tones will be weak and the position of

the various instruments obscure.

• Contact between bare speaker wires

at the speaker terminals may result in

a short-circuit.

• The speaker grille cannot be removed.

Do not attempt to remove the grille

on the speaker system. If you try to

remove it, you may damage the

speaker.

If you encounter color irregularity on

a nearby TV screen

This speaker system is magnetically

shielded to allow it to be installed near a

TV set. However, color irregularities

may still be observed on certain types of

TV sets.

If color irregularity is observed…

p Turn off the TV set once, then turn

it on again after 15 to 30 minutes.

If color irregularity is observed

again…

p Place the speakers further away

from the TV set.

If howling occurs

Reposition the speakers or turn down

the volume on the amplifier.

On cleaning

• Clean the cabinet, panel and controls

with a soft cloth slightly moistened

with a mild detergent solution. Do

not use any type of abrasive pad,

scouring powder or solvent such as

alcohol or benzine.

If you have any question or problem

concerning your amplifier, please

consult your nearest Sony dealer.

Getting Started

3

GB

About This Manual

Conventions

• The instructions in this manual

describe the controls on the amplifier

and speakers. You can also use the

controls on the remote if they have

the same or similar names as those on

the amplifier.

• The following icons are used in this

manual:

Indicates that you can use only

the remote to do the task.

Indicates hints and tips for

making the task easier.

This amplifier contains a Dolby Pro

Logic Surround decoder.

Manufactured under license from Dolby

Laboratories.

“Dolby”, “AC-3”, “Pro Logic” and the

double-D symbol ; are trademarks of

Dolby Laboratories.

Hold down ?/1 and press CENTER

MODE to change the fan control

setup. Each time you do the

procedure above, the following setup

appears.

Select To

FAN ON Turn on the fan at all

times.

FAN AUTO Turn on the fan

automatically when

there is sufficient

speaker output.

TABLE OF CONTENTS

Getting Started

Unpacking 4

Hookup Overview 4

Video Component Hookups 5

Speaker System Hookups and Setups 6

AC Hookups 9

Before You Use Your Amplifier 10

Amplifier Operations

Selecting a Component 11

Changing the Factory Setting of a FUNCTION Button 13

Using the Sleep Timer 14

Using Surround Sound

Choosing a Sound Field 15

Getting the Most Out of Dolby Pro Logic Surround Sound 16

Additional Information

Troubleshooting 18

Specifications 19

Glossary 20

Remote Button Description 21

Index 22

Rear Panel Descriptions 22

Getting Started

4

GB

Getting Started

Unpacking

Check that you received the following items with your

amplifier:

• Remote commander (remote) (1)

• Size AA (R6) batteries (2)

• Scart adaptor (1)

• Speakers (5)

• Front speakers (2)

• Rear speakers (2)

• Center speaker (1)

• Subwoofer (1)

• Speaker connecting cord, 10 m (2)

• Speaker connecting cord, 2.5 m (3)

• Monaural connecting cord (1 phono to 1 phono) (1)

• Foot pads (20)

Inserting batteries into the remote

Insert two size AA (R6) batteries with the + and – on

the battery compartment. When using the remote,

point it at the remote sensor g on the amplifier.

When to replace batteries

Under normal use, the batteries should last for about 6

months. When the remote no longer operates the

amplifier, replace both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or humid

place.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from

battery leakage and corrosion.

]

}

Hookup Overview

The amplifier allows you to connect and control the

following video components. Follow the hookup

procedures for the components that you want to

connect to the amplifier on the pages specified. To

learn the locations and names of each jack, see “Rear

Panel Descriptions” on page 22.

Before you get started

• Turn off the power to all components before making

any connections.

• Do not connect the mains lead until all of the

connections are completed.

• Be sure to make connections firmly to avoid hum

and noise.

• When connecting an audio cable, be sure to match

the colour-coded pins to the appropriate jacks on the

components: White (left, audio) to White; and Red

(right, audio) to Red.

Rear

speaker

(L)

Rear

speaker

(R)

Front

speaker

(L)

Front

speaker

(R)

TV

Video Component

Hookups (5)

VCR

Speaker System

Hookups (6)

DVD

player/

AC-3

decoder

Active

subwoofer

Center

speaker

Getting Started

5

GB

Video Component Hookups

Overview

This section describes how to connect video

components to the amplifier. For specific locations of

the jacks, see the illustration below.

What cords will I need?

• Scart adaptor (supplied)

• Euro AV cable (not supplied) (1 for each TV or VCR)

• Audio cords (not supplied) (1 for DVD player, 2 for AC-3

decoder’s FRONT and REAR jacks)

• Monaural audio cords (not supplied)

(2 for AC-3 decoder’s CENTER and WOOFER jacks)

5.1CH/DVD TV

DVD 2CH

VIDEO

VTRTV

L

R

L

R

To VTR audio input

Amplifier

VIDEO AUDIO IN

ç

Euro AV cable (not

supplied)

Scart adaptor

(supplied)

To TV

n

TV

White

(L)

White

(L)

Red

(R)

Red

(R)

ç

To TV audio input

Hookups

The arrow l indicates signal flow.

TV/VCR

You can listen to the sound from VCR or TV by

connecting the audio signal from VCR or TV to the

amplifier.

If you have another component, such as a second VCR

or LD player, connect it to the DVD 2CH jacks.

DVD Player

If your DVD player does not have 5.1 CH output,

connect the audio output jacks of the DVD player to the

DVD 2CH jacks of the amplifier.

AUDIO IN

AUDIO OUT

DVD 2CH

LL

RR

L

Amplifier

DVD 2CH

DVD player

AUDIO OUT

(continued)

Red (R)

White (L)White (L)

BlackBlack

Getting Started

6

GB

DVD player with AC-3 decoder

If you have a Dolby Digital (AC-3) decoder or a DVD

player with a built-in AC-3 decoder, you can play

decoded Dolby Digital (AC-3) soundtracks through the

speakers connected to the amplifier. Connect the

decoder as follows:

Amplifier

5.1 CH/DVD

Dolby Digital AC-3

decoder (etc.)

FRONT

REAR

CENTER

WOOFER

CENTER

WOOFER

PRE OUT

FRONT

REAR

5.1CH / DVD

L L

RR

5.1CH OUTPUT

L

Speaker System Hookups and

Setups

Overview

This section describes how to connect the supplied

speakers (SS-MS215) to the amplifier. Connecting the

active woofer (SA-WMS215) will increase bass

response.

For specific locations of the terminals, see the

illustration below.

What cords will I need?

• Speaker connecting cord (supplied) (1 for each speaker)

• Monaural connecting cord (supplied)

FRONT

SPEAKERS

CENTER

SPEAKER

WOOFER

(AUDIO OUT)

REAR

SPEAKERS

(+)(+)

(–)

Black

Getting Started

7

GB

Hookups

Front speakers (SS-MS215)

Rear and center speakers (SS-MS215)

Notes

• Be sure to match the speaker cord to the appropriate

terminal on the components: + to + and – to –. If the cords

are reversed, the sound will be distorted and will lack

bass.

• Make sure all connections are firm. Contact between bare

speaker wires at the speaker terminals may cause a short-

circuit.

SPEAKERS

R-REAR-L CENTER

Rear speaker

(R)

Center speaker

Rear speaker

(L)

Amplifier

Front speaker

(R)

Front speaker

(L)

SPEAKERS

R-FRONT-L

To avoid short-circuiting the speakers

Short-circuiting of the speakers may damage the

amplifier. To prevent this, make sure to take the

following precautions when connecting the speakers.

Make sure the stripped ends of each speaker cord does

not touch another speaker terminal or the stripped end

of another speaker cord.

Examples of poor conditions of the speaker cord:

Stripped speaker cord is touching another speaker

terminal.

Stripped cords are touching each other due to excessive

removal of insulation.

After connecting all the components, speakers, and AC

power cord, output a test tone to check that all the

speakers are connected correctly. For details on

outputting a test tone, refer to “Adjusting the speaker

volume” on page 17.

If you have connected rear speakers, be sure to press

the 5.1 CH/DVD button on the amplifier before

outputting a test tone so that the tone is output

individually from the left and right rear speakers.

If no sound is heard from a speaker while outputting a

test tone or a test tone is output from a speaker other

than the one whose name is currently displayed on the

amplifier, the speaker may be short-circuited. If this

happens, check the speaker connection again.

R

EAR

+

–

RL

REAR

+

–

R

L

RL

Getting Started

8

GB

Positioning the speakers

Location of each speaker

Each speaker should face the listening position. Better

surround effect will result if all speakers are set at the

same distance from the listening position.

Place the front speakers at a suitable distance to the left

and right of the television.

Place the subwoofer on either side of the television.

Place the center speaker on the top-center of the TV set.

The placement of rear speakers greatly depends on the

configuration of the room. The rear speakers may be

placed on both sides of the listening position A or

behind the listening position B.

Setting the speakers

To prevent speaker vibration or movement while

listening, attach the supplied foot pads to the bottom

four corners of the center speaker, front speakers, and

rear speakers.

Front/Center/Rear

speakers

Foot pads

Active subwoofer (SA-WMS215)

Caution

• The speaker unit of the active subwoofer is located at the

bottom of the active subwoofer.

• Avoid contact with the speaker unit as it is without a

cover.

• Place the active subwoofer on a flat surface to ensure there

is no obstruction to the speaker unit.

Active subwoofer

Amplifier

AUDIO OUT

WOOFER

INPUT

Center

Subwoofer

Front

(Right)

Rear

(Right)

Rear

(Left)

Front

(Left)

Getting Started

9

GB

Setting the center speaker

Set the center speaker firmly on top of the TV set,

making sure it is completely level.

Setting other speakers

For greater flexibility in the positioning of the speakers,

use the optional WS-FV10, WS-TV10, or WS-WV10

speaker stand (available only in certain countries).

Note

You do not need to attach the foot pads if you are using the

speaker stand.

Tip

The height of the front speakers should be adjusted to about

the center of the TV screen.

Foot pads

WS-FV10 WS-TV10

WS-WV10

(for rear speakers)

to a wall outlet

/

AC Hookups

Connecting the mains lead

Connect the mains lead from this amplifier, active

subwoofer and from your video components to a wall

outlet.

Amplifier

Active subwoofer

to a wall outlet

/

Getting Started

10

GB

Before You Use Your Amplifier

Before you use your amplifier for the first time or when

you want to clear the amplifier’s memory, do the

procedure below:

1 Turn off the amplifier.

2 Press ?/1 (power) for more than 4 seconds.

“INITIAL” appears in the display and the items

including the following are reset or cleared:

• All sound field parameters are reset to their

factory settings.

• The fan control setup is reset to FAN ON.

Note

If you are using a Sony DVD player together with this home

theater system, set your DVD player to the following

configuration:

If you are using a non Sony DVD player, refer to the

operating instructions supplied with the DVD player for

speaker setup.

?/1 (power)

Speakers

Front

Center

Rear

Subwoofer

Settings

SMALL

YES

Amplifier Operations

11

GB

Amplifier Operations

Selecting a Component

To listen to a connected component, first select the

function on the amplifier or with the remote.

Before you begin, make sure you have:

• Connected all components securely and correctly as

indicated on pages 5 to 9.

1 Press 1/u (power) to turn on the amplifier.

2 Turn MASTER VOLUME to VOL MIN (indicated

on the display) to avoid damaging your speakers.

3 Press a function button to select the component

you want to use:

To operate with the remote

Refer to “Using the remote” on page 12 for details.

4 Turn on the component, the VCR for example,

and start playback.

5 Turn MASTER VOLUME to adjust the volume.

MASTER VOLUME

1/u (power)

Function buttons

To watch

Video tapes

TV programmes

Digital versatile disc

(DVD)

DVD through

AC-3 decoder

Press

VIDEO

TV

DVD 2CH

5.1 CH/DVD

TV input mode

VIDEO

To

Mute the sound

Do this

Press MUTING on the remote.

Press again to restore the sound.

Watching video programmes

To take full advantage of the amplifier’s surround

sound effects, like Dolby Surround, turn off the

speakers on your TV before you start. This also lets you

use the amplifier’s remote to control the sound.

To watch TV programmes, do the following:

1 Turn on your TV.

2 Turn on the amplifier and press TV.

To watch videos or DVDs, do as follows:

1 Turn on your TV and set the TV’s input to match

the video component you watch.

2 Turn on the amplifier and press the function

button (VIDEO, DVD 2CH or 5.1 CH/DVD) to

select the component you want to use.

3 Turn on the video component and start

playback.

(continued)

Amplifier Operations

12

GB

Using the remote

The remote lets you operate the amplifier and the Sony

components that are connected to it.

1 Press one of the SYSTEM CONTROL/

FUNCTION buttons to select the component you

want to use.

The amplifier and the selected component turn

on.

The SYSTEM CONTROL/FUNCTION buttons on

the remote are factory-set as follows:

If you want to change the factory setting of a button

See “Changing the Factory Setting of a FUNCTION

Button” on page 13.

If the component does not turn on

Press the power switch on the component.

2 Start playing.

Refer to “Remote Button Descriptions” on page 21

for details.

?/1

AV ?/1

SYSTEM

CONTROL/

FUNCTION

To play

TV programmes

VHS Tapes

(VTR-3 mode)

DVD player

(for 2-ch playback)

DVD player/

AC-3 decoder

Press

TV

VIDEO

DVD

5.1 CH

To turn off the components

Press AV ?/1 and ?/1 simultaneously. This will also turn

off the Sony video/audio components at the same time. If

the components do not turn off, press the power switch on

the components.

If you use a Sony TV

• The TV turns on automatically and switches to the

appropriate video input when you press VIDEO. If

the TV does not switch to the appropriate input

automatically, press TV/VIDEO on the remote.

• When you use the TV only, turn on the TV using the

TV’s remote.

Amplifier Operations

13

GB

SYSTEM

CONTROL/

FUNCTION

MENU

control keys

Changing the Factory Setting

of a FUNCTION Button

If the factory settings of the SYSTEM CONTROL/

FUNCTION buttons (“Using the remote” on page 12)

don’t match your system components, you can change

them. The following table shows the possibility of

alternate function assignment for each button.

Button Possible assignment

VIDEO VTR 1, VTR 2, VTR 3

DVD DVD, LDP, CD

* Initial setting of VIDEO is VTR 3.

* Sony VCRs are operated with a VTR 1, 2, or 3 setting that

corresponds to Beta, 8mm, and VHS, respectively.

Resetting key table for function key VIDEO

VTR 1 CURSOR UP

VTR 2 ENTER/EXECUTE

VTR 3 CURSOR DOWN

Resetting key table for function key DVD

DVD EXIT/RETURN

LD DISPLAY

CD CURSOR RIGHT

For example, if you connect a Sony LD player to the

DVD jacks, you can assign the DVD button to set the

remote to control the LD player.

1 Hold down the SYSTEM CONTROL/FUNCTION

button whose function you want to change (DVD,

for example).

2 Press the corresponding button of the component

you want to assign to the SYSTEM CONTROL/

FUNCTION button (DISPLAY, LD player, for

example).

Now you can use the DVD button to control your

Sony LD player.

To reset a button to its factory setting

Repeat the above procedure.

To reset all the function buttons to their factory setting

Press ?/1, AV ?/1 and MASTER VOL – at the same time.

Amplifier Operations

14

GB

SLEEP

t 2:00:00 t 1:30:00 t 1:00:00 t 0:30:00 t OFF

Using the Sleep Timer

You can set the amplifier to turn off automatically at a

time you specify.

Press SLEEP on the remote while the power is on.

Each time you press SLEEP, the time changes as shown

below.

The display dims after you specify the time.

You can check the time remaining before the

amplifier turns off

Press SLEEP on the remote. The remaining time appears

in the display.

Using Surround Sound

15

GB

Using Surround Sound

Choosing a Sound Field

You can take advantage of surround sound simply by

selecting one of the three pre-programmed sound field

according to the type of programme you wish to play.

1 Press SOUND FIELD or SOUND FIELD ON/OFF

on the remote to turn on the sound field.

One of the SOUND FIELD indicators lights up in

the display.

2 Press SOUND FIELD or SOUND FIELD MODE

on the remote repeatedly until the indicator for

the sound field you want lights up.

Select the appropriate sound field as follows:

* “DOLBY PL” appears on the display.

To turn off sound field

Press SOUND FIELD ON/OFF on the remote or press

SOUND FIELD repeatedly until “SF OFF” appears on the

display.

SOUND FIELD

Sound field indicators

SOUND FIELD

MODE

EFFECT/

DELAY –/+

SOUND FIELD

ON/OFF

Select

PRO LOGIC*

C. STUDIO

(Cinema Studio)

SIMULATED

To

Decodes programmes processed

with Dolby Pro Logic Surround.

Reproduces the sound characteristics

of a movie theater. Good for

watching standard movies.

Create a simulated surround sound

from monaural sources such as old

movies or TV programmes.

You can find Dolby Surround-encoded software by

looking at the packaging

However, some videos and laser discs may use Dolby

Surround sound even if it’s not indicated on the

package.

Note

Surround sound is turned off when you select the

5.1 CH/DVD.

Adjusting the effect level

(for C. STUDIO and SIMULATED only)

You can make the surround sound more prominent by

increasing the EFFECT level. This control lets you

adjust the “presence” of the surround effect in six steps

(1-6).

1 Start playing a programme source.

2 Use EFFECT/DELAY (–/+) on the remote to

select the level you prefer. The effect level is

indicated on the display.

Note

Changing the effect level may not produce major variations

in the surround effect when used with certain playback

sources.

Using Surround Sound

16

GB

Getting the Most Out of Dolby

Pro Logic Surround Sound

To obtain the best possible Dolby Pro Logic Surround

sound, first select the center mode according to the

speaker system you have. Then, adjust the volume of

each speaker.

Note that you must connect the rear speakers and/or

one center speaker to do the following adjustments.

SOUND FIELDCENTER MODE

Center mode

indicators

Display

Sound field

indicators

SOUND FIELD

MODE

EFFECT/

DELAY –/+

CENTER

LEVEL +/–

REAR

LEVEL +/–

SOUND FIELD

ON/OFF

TEST TONE

Selecting the center mode

The amplifier offers you four center modes: Phantom,

Wide, Normal and 3 Stereo. Each mode is designed for

a different speaker configuration.

1 Press SOUND FIELD repeatedly to select the PRO

LOGIC sound field.

2 Press CENTER MODE repeatedly until the

indicator for the center mode you want lights in

the display.

Select the center mode as follows:

Notes

• To match the speaker system that is packed together with

this amplifier, we recommend that you set the center

mode to NORMAL or WIDE and turn on the subwoofer.

• If you are using a different speaker system, select the

mode that best suits your speaker system’s configuration.

So that

The sound of the

center channel is

output from the front

speakers.

The center channel

fully reproduces the

entire audio spectrum

The bass sound of the

center channel is

output from the front

speakers.

The sound of the rear

channel is output

from the front

speakers.

If you have

Front and rear

speakers, no

center speaker

Front and rear

speakers, and

a large center

speaker

Front and rear

speakers, and

a small center

speaker

Front and center

speakers, no rear

speaker

Select

PHANTOM

WIDE

NORMAL

3 STEREO

(3 Channel Logic)

Using Surround Sound

17

GB

Adjusting the speaker volume

The test tone feature lets you set the volume of your

speakers to the same level.

Using the controls on the remote lets you test the

speaker connection and adjust the volume level from

your listening position.

1 Press SOUND FIELD repeatedly to select

“DOLBY PL” and set the center mode to

NORMAL.

2 Press TEST TONE on the remote.

You will hear the test tone from each speaker

sequentially.

3 Adjust the volume level so that the test tone from

each speaker is at the same level from your

listening position.

• To adjust the level of center speaker, press

CENTER LEVEL + or – on the remote.

• To adjust the level of rear speakers, press

REAR LEVEL + or – on the remote.

The center and rear levels are indicated on the

display.

4 Press TEST TONE on the remote to turn off the

test tone.

You can adjust all speakers at one time

Adjust MASTER VOL on the remote or MASTER

VOLUME on the amplifier.

You can increase the output level of the rear

speakers

The adjustment range of the rear speakers is preset from

–10 to +6, but you can shift the range up 3 levels (–7 to

+9). Hold down SOUND FIELD on the amplifier while

turning on the power until “NORMAL” appears on the

display.

The values for the rear level remain fixed at –10 to +6 in

the display, but you will be able to hear the difference in

the actual output level.

To reset the rear level adjustment range, repeat this

procedure to display “GAIN LOW”.

Note

During 5.1 CH/DVD mode, CENTER LEVEL and REAR

LEVEL cannot be adjusted.

Adjusting the delay time

You can make the surround sound more effective by

delaying the output from the rear speakers (delay

time). You can select from three delay times, S (15 mS),

M (20 mS), and L (30 mS). For example, if you’ve

placed the rear speakers in a large room or apart from

your listening position, set the delay time shorter.

1 Start playing a programme source encoded with

Dolby Surround sound.

2 Press SOUND FIELD repeatedly to select

“DOLBY PL” and set the center mode to

NORMAL.

3 Press EFFECT/DELAY (–/+) on the remote

repeatedly to choose the delay time parameter.

The current delay time appears in the display,

such as “DELAY S,” “DELAY M” or “DELAY L.”

Note

If the AC power cord is disconnected for about one week,

amplifier’s surround parameter will be reset to the factory

settings.

Adjusting the subwoofer

Slight adjustments to the system can enhance your

sound enjoyment.

1 Rotate LEVEL to adjust the volume.

Set the volume level to best suit your preference

according to the programme source.

Note

To enjoy high-quality sound, do not turn the subwoofer

volume too high.

LEVEL

MIN MAX

POWER

LEVEL

Additional Information

18

GB

Additional Information

Troubleshooting

If you experience any of the following difficulties while

using the home theater system, use this

troubleshooting guide to help you remedy the

problem. Should any problem persist, consult your

nearest Sony dealer.

There’s no sound or only a very low-level sound is heard.

, Check that the speakers and components are

connected securely.

, Press MUTING on the remote if the MUTING

indicator turns on.

, Make sure you select the correct component

on the amplifier.

, Check whether or not you used the

appropriate AV cables.

, The protective device on the amplifier has

been activated because of a short circuit.

(“PROTECT” flashes.) Turn off the amplifier,

eliminate the short-circuit problem and turn

on the power again.

The left and right sounds are unbalanced or reversed.

, Check that the speakers and components are

connected correctly and securely.

Severe hum or noise is heard.

, Check that the speakers and components are

connected securely.

, Check that the connecting cords are away

from a transformer or motor, and at least 3

meters (10 feet) away from a TV set or

fluorescent light.

, Place your TV away from the audio

components.

, The plugs and jacks are dirty. Wipe them

with a cloth slightly moistened with alcohol.

No sound or only a very low-level sound is heard from

the rear speakers.

, Select the appropriate center mode (see page

16).

, Adjust the speaker volume appropriately (see

page 17).

, Make sure you turn on the sound field

surround mode function.

Note

The Dolby Surround effect is dependent on the software

and center mode being used.

No sound is heard from the center speaker.

, Select the appropriate center mode (see page

16).

, Adjust the speaker volume appropriately (see

page 17).

No sound or only a very low-level sound is heard from

the subwoofer.

, Make sure you turn on the subwoofer.

, Make sure the connection is made correctly.

The sound has suddenly stopped.

, Make sure all the connections have been

correctly made. Contact between bare speaker

wires at the speaker terminals may cause a

short-circuit.

Surround effect cannot be obtained.

, Make sure you turn on the sound field

function.

No picture or an unclear picture is seen on the TV screen.

, Select the appropriate input on your TV.

, Select the appropriate component on the

amplifier.

The remote does not function.

, Point the remote at the remote sensor g on

the amplifier.

, Remove the obstacles in the path of the

remote and the amplifier.

, Replace both batteries in the remote with new

ones if they are weak.

, Make sure you select the correct function on

the remote.

Additional Information

19

GB

Specifications

Amplifier section

(DIN 1 kHz, 8 ohms)

25 W + 25 W

(DIN 1 kHz, 8 ohms)

Front: 25 W / ch

Center: 25 W

Rear: 25 W / ch

TV, VIDEO, DVD 2CH,

5.1 CH/DVD :

10 Hz - 50 kHz +0.5/–2 dB

WOOFER:

Voltage: 1 V

Impedance: 1 kilohms

Full mute

220 - 230 V AC, 50/60 Hz

115 W

430 x 274 x 64.5 mm

4.6 kg

Power output

Rated Power

Output at Stereo

mode

Reference

Power Output

Frequency

response

Inputs

Outputs

Muting

Power

requirements

Power

consumption

Dimensions

Mass (Approx.)

TV,

VIDEO,

DVD 2CH,

5.1 CH/

DVD

Sensitivity

250 mV

Impedance

50

kilohms

S/N

(weighting

network,

input level)

85 dB*

(A, 250 mV)

Full range, magnetically

shielded

5 cm cone type

Bass reflex

8 ohms

60 watts

84 dB (1 W, 1m)

150 Hz - 20, 000 Hz

Approx. 76 x 100 x 86 mm

including front grille

Approx. 425 g

Speaker system

Speaker units

Enclosure type

Rated

impedance

Power handling

capacity

(Maximum input

power)

Sensitivity level

Frequency range

Dimensions

(w/h/d)

Mass

General

Speaker section

SS-MS215 Front, center and rear

speakers

SA-WMS215 Subwoofer

System

Speaker system

Speaker unit

Enclosure type

Continuous RMS

power output

(8 ohms, 20 -

250 Hz)

Reproduction

frequency range

High frequency

cut-off

frequency

Power

requirements

Power

consumptions

Dimensions

(w/h/d)

Mass

Supplied

accessories

Active subwoofer,

magnetically shielded

Woofer: 16 cm cone type

Acoustically Loaded Bass

Reflex

50 W

32 Hz - 250 Hz

250 Hz

220 - 230 V AC, 50/60 Hz

45 W

Approx. 240 x 285 x 355

mm including front

panel

Approx. 8 kg

See page 4.

Input

General

LINE IN (input pin jack)

Design and specifications are subject to

change without notice.

Specifications indicated are measured at

230 VAC, 50Hz.

*78 IHF

Additional Information

20

GB

Glossary

Center mode

Setting of speakers to enhance Dolby Pro

Logic Surround mode. To obtain the best

possible surround sound, select one of the

following four center modes according to

your speaker system.

• NORMAL mode

Select NORMAL mode if you have front

and rear speakers and a small center

speaker. Since a small speaker cannot

produce enough bass, the bass sound of

the center channel is output from the front

speakers.

• WIDE mode

Select WIDE mode if you have front and

rear speakers and a large center speaker.

With the WIDE mode, you can take full

advantage of Dolby Surround sound.

• PHANTOM mode

Select PHANTOM mode if you have front

and rear speakers but no center speaker.

The sound of the center channel is output

from the front speakers.

• 3 STEREO (3 CH LOGIC)

Select 3 STEREO mode if you have front

and center speakers but no rear speaker.

The sound of the rear channel is output

from the front speakers to let you

experience some of the surround sound

without using rear speakers.

Dolby Pro Logic Surround

Decoding system of Dolby Surround sound

standardized in TV programmes and movies.

Compared with the former Dolby Surround

system, Dolby Pro Logic Surround improves

sound image by using four separate channels:

off-screen audio effects, on-screen dialog, left-

to-right panning, and music. These channels

manipulate the sound to be heard and

enhance the action as it happens on the

screen. To take advantage of Dolby Pro Logic,

you should have at least one pair of rear

speakers and/or one center speaker. You also

need to select the appropriate center mode to

enjoy a full effect.

Dolby Digital (AC-3)

This surround format is more advanced than

Dolby Pro Logic Surround. In this format, the

rear speakers output stereo sound with an

expanded frequency range and a subwoofer

channel for deep bass is independantly

provided. This format is also called “5.1”

because the subwoofer channel is counted as

0.1 channel (since it functions only when a

deep bass effect is needed.)

All six channels in this format are recorded

separately to realize superior channel

separation. Furthermore, since all the signals

are processed digitally, less signal

degradation occurs. The name “AC-3” comes

from the fact that it is the third audio coding

method to be developed by the Dolby

Laboratories Licensing Corporation.

5.1 CH/DVD jacks

These jacks are used to input decoded Dolby

Digital (AC-3) audio signals, allowing you to

enjoy 5.1 channel surround sound. Use these

jacks to connect a Dolby Digital (AC-3)

decoder or a DVD player with a built-in AC-3

decoder.

Surround sound

Sound that consists of three elements: direct

sound, early reflected sound (early

reflections) and reverberative sound

(reverberation). The acoustics where you hear

the sound affect the way these three sound

elements are heard. These sound elements are

combined in such a way that you can actually

feel the size and the type of a concert hall.

• Types of sound

• Transition of sound from rear speakers

Test tone

Signal given out by the amplifier for

adjusting the speaker volume. The test tone

will come out as follows:

• In a system with a center speaker

(NORMAL/WIDE/3 STEREO modes)

The test tone is output from the front L

(left), center, front R (right), and rear

speakers in succession.

• In a system without a center speaker

(PHANTOM mode)

The test tone is output from the front and

the rear speakers alternately.

Center

speaker

Rear

speaker (R)

Rear

speaker (L)

Front

speaker (R)

Front

speaker (L)

Center

speaker

Rear

speaker (R)

Rear

speaker (L)

Front

speaker (R)

Front

speaker (L)

Front

speaker (L)

Front

speaker (R)

Rear

speaker (R)

Rear

speaker (L)

Direct sound

Early

reflections

Reverberation

Level

Early reflection time

Time

Center

Front (R)

Front (L)

Rear (L, R)

3 STEREO

NORMAL/WIDE

Rear (L, R)

PHANTOM

Front (L, R)

Center

speaker

Front

speaker (R)

Front

speaker (L)

Reverberation

Early reflections

Direct sound

Page is loading ...

Sony HT-K170 User manual

Sony HT-K170 User manual

in other languages

Related papers

Other documents