Craftsman 351217430 Owner's manual

Brand: Craftsman

Model: 351217430

Category: Power planers

Type: Owner's manual

This manual is also suitable for

351.217430

Operator's Manual g

13" I

PLANER WITH DUST COLLECTION

Model No.

351.217430

CAUTION: Read and follow

all Safety Rules and Operating

Instructions before First Use

of this Product.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.con_craftsman

18236.03 Draft (07/01/04)

Warranty.................................... 2

Safety Rules ............................... 2-3

Unpacking .................................. 3

Assembly ................................. 3-4

Installation ................................. 4-5

Operation ................................. 6-9

Maintenance .............................. 9-11

Troubleshooting ........................... 12-13

Parts Illustration and List ................... 14-19

Espa_ol ................................. 20-31

FULL ONE YEAR WARRANTY

Ifthis productfails due toa defect in material or work-

manship within one year from the date of purchase,

Sears willat its optionrepair or replace itfree of

charge. Contactyour nearest Sears Service Center

(1-800-4-MY-HOME) to arrange for productrepair,or

returnthis productto place of purchase for replacement.

If this productis used for commercial or rentalpurpos-

es, this warrantywill applyfor 90 days from the date of

purchase.

This warranty applies only while this product is used in

the United States.

This warrantygives you specificlegal dghts and you may

also have other rights which vary from stateto state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman

Estates, IL 60179

WARNING: For yourown safety, read all of the rules

and precautions before operating tool.

CAUTION: Always follow properoperating procedures

as defined in this manual even ifyou are familiar with

use of this or similar tools. Remember that being care-

less for even a fraction of a second can result in severe

personal injury.

BE PREPARED FOR JOB

• Wear proper apparel. Do not wear loose clothing,

gloves, neckties, rings, bracelets or otherjewelry

which may get caught in moving parts of machine.

• Wear protective hair covering to contain long hair.

• Wear safety shoes with non-slip soles.

• Wear safety glasses complying with United States

ANSI Z87.1. Everyday glasses have only impact

resistant lenses. They are NOT safety glasses.

• Wear face mask or dust mask if operation is dusty.

• Be alert and think clearly Never operate power tools

when tired, intoxicatedor when taking medications

that cause drowsiness.

PREPARE WORK AREA FOR JOB

• Keep work area clean. Cluttered work areas invite

accidents.

• Do not use power tools in dangerous environments.

• Do not use power toots in damp or wet locations.Do

not expose power tools to rain.

• Work area should be properly lighted.

• Proper electrical receptacle shouldbe available for

tool. Three prong plug should be plugged directly

into properly grounded, three-prong receptacle.

• Extension cords should have a grounding prong and

the three wires of the extension cord shouldbe of

the correct gauge.

• Keep visitors at a safe distance from work area.

• Keep childrenout of workplace. Make workshop child-

proof. Use padlocks, master switches or remove switch

keys to prevent any unintentional use of power tools.

TOOL SHOULD BE MAINTAINED

• Always unplugtool priorto inspection.

• Consult manual for specificmaintainingand adjust-

ing procedures.

• Keep toollubricatedand clean for safest operation.

• Remove adjustingtools. Form habitof checkingto

see that adjustingtools are removedbefore switch-

ingmachine on.

• Keep all parts in workingorder.Check to determine

that the guard or other parts will operate properly

and perform their intended function.

• Check for damaged parts. Check for alignmentof

moving parts, binding, breakage, mounting and any

other condition that may affect a tool's operetlon.

• A guard or other part that is damaged should be

properly repaired or replaced. Do not perform

makeshift repairs. (Use parts list provided to order

replacement parts.)

KNOW HOW TO USE TOOL

• Use right toolfor job. Do not force tool or attachment

to do a job for which it was not designed.

• Disconnect tool when changing blades.

• Avoid accidental start-up. Make sure that the switch

is in the OFF position before plugging in.

• Do not forcetool. It willwork most efficientlyat the

rate for which it was designed.

• Keep hands away from moving parts and cutting

surfaces.

• Never leave tool runningunattended. Turn the power

offand do not leave tool untilit comes toa complete

stop.

• Do notoverreach. Keep proper footingand balance.

• Never standon tool.Seriousinjurycould occurif toolis

tipped or if blade is unintentionally contacted.

• Know your tool. Learn the tool's operation, applica-

tion and specific limitations.

• Use recommended accessories (refer to page 15).

Use of improper accessories may cause risk of

injuryto persons.

• Handle workpiece correctly.Protect handsfrom

possible injury.

• Turn machine off if it jams. Blade jams when it digs

too deeply into workpiece. (Motor force keeps it

stuck in the work.)

• Always keep drive, cutterhead and blade guards in

place and in proper operating condition.

• Feed work into blade or cutter against direction of

rotation.

CAUTION: Think safety! Safety is a combinationof

operator common sense and alertness at all times

when tool is being used.

WARNING: Do not attempt to operate tool untit it is

completely assembled according to the instructions.

Refer to Figure 1 below.

Check for shipping damage. If damage has occurred, a

claim must be filed with carrier. Check for complete-

ness. immediately report missing parts to dealer,

The planer comes assembled as one unit. Additional

parts which need to be fastened to planer shouldbe

tocated and accounted for before assembling.

A. Planer

B. Handle Assembly

C. 6ram Flat Washer

D. 6-1.0 x 20mm Socket Pan Head Bolt

E. 6-1.0 x 25mm Socket Head Bolt

F. Pointer

G. Magnet (2)

H. 4ram HexWrench

I. Dust Chute

J. Half Bag Dust CollectionSet (Not Shown)

Figure 1 - Unpacking

WARNING: Do not attempt assembly if parts are

missing. Use this manual to order replacement parts,

INSTALL HANDLE

Refer to Figures 2 and 3.

• Handle with knob (A) can be installedeither to

top-right or top-left side of the planer,

• Remove plug on elevation screw (B) from the side

where handle will be installed.

Figure 2 - Install Handle

• Insert handle with knob (A) onto elevation screw top

(B).

Figure3 - Secure Handle

• Positionthe pointer (E) and washer (D) on the handle.

• Secure handle with bolt (C) usingthe wrench

provided,

INSTALL DUST CHUTE

Refer to Figure 22.

• Slide dust chute (Key No. 10) over fan housing(Key

No. 8). Secure in positionwith bolt(Key No 9).

• Attach the Half Bag Dust CollectionSet (included)

after mounting planer to work surface.

MOUNT PLANER TO WORK SURFACE

Refer to Figure 4.

• Planer isdesigned to be portable so itcan be moved

to job site, butshould be mountedto stable, level

bench or table. See Recommended Accessories,

page 15.

• Base of planer has four mounting holes (A). Holes

form a rectangle. Use a square to mark position on

work surface.

• If pre-drilled holes do not existon work surface, drill

four holes.

• Slide arm withspring over dust chute.

• Assemble bag support. Slide connectorsinto

channels of support segments:

• Slide plastic trash bag inside and over bag support.

Let bag overlap 3-4".

• Place band of the filter bag over and into the

channel of the bag support.

• Secure in position by tightening strap.

Figure 5 - Half Bag Dust Collection Set

Figure4 - MountPlaner

• Securely mount planer towork surface by bolting

(hardware not supplied) itthrough the holes.

INSTALLING THE HALF BAG DUST

COLLECTION SET

Refer to Figure 5.

The Craftsman Half Bag Dust CoUection Set is

designed to provide dust collection for woodworking

tools with a 2%" diameter dust exhaust port. The filter

bag attaches to a 30-gaUon trash can or a 30-gallon x

1.3 mil plastic trash bag for easy, convenient sawdust

disposal (trash can and plastic trash bag not included).

• Mount planer to work bench or table before installing

Dust Collection Set,

To use dust collection set with a trash can:

• Place spring inside filter bag arm.

• Slide arm with spring over dust chute.

• Place band of the bag over rim oftrash can and

secure bag by tightening strap.

To use dust collection set with a trash bag:

• Place spring inside filter bag arm.

POWER SOURCE

WARNING: Do not connectplaner to the power

source untilall assembly steps have been completed.

The motoris designedfor operationon the voltage and

frequency specified. Normal loads willbe handledsafe-

lyon voltages not more than 10% above or belowspec-

ified voltage. Running the uniton voltageswhichare not

within range may cause overheating and motor burn-

out. Heavy loads require that voltage at motor terminals

be no less than the voltage specifiedon nameplate.

• Power supply to the motor is controlled by a switch

with key.Removing the key from switch will lock the

unit and prevent unauthorized use.

GROUNDING INSTRUCTIONS

WARNING: Improper connection of equipment

groundingconductorcan resultin the riskof electrical

shock.Equipment shouldbe groundedwhile in use to

protectoperatorfrom electrical shock.

• Check with a qualified electricianifyou do not

understand groundinginstructionsor ifyou are in

doubt as to whether the tool is properlygrounded.

• This tool isequipped withan approvedcord rated at

150V and a 3-prong groundingtype plug (see Figure

6) for your protectionagainst shockhazards.

• Grounding plug should be plugged directly into a

properly installed and grounded 3-prong grounding-

type receptacle, as shown (see Figure 6).

Properly Grounded Outlet _

Grounding Prong ®11

3-Prong Plug __

Figure 6 - 3-Prong Receptacle

• Do not remove or alter grounding prong in any manner.

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electrical shock.

WARNING: Do not permit fingers to touch the termi-

nals of plug when installing or removing from outlet.

• Plug must be plugged into matching outlet that is

properly installed and grounded in accordance with

all local codes and ordinances. Do not modify plug

provided. If it will not fit in outlet, have proper outlet

installed by a qualified electrician.

• Inspect tool cords periodically, and if damaged, have

repaired by an authorized service facility.

• Green (or green and yellow) conductor in cord is the

grounding wire. If repair or replacement of the elec-

tric cord or plug is necessary, do not connect the

green (or green and yellow) wire to a live terminal.

• A 2-prong wall receptacle must be replaced with a

properly grounded 3-prong receptacle installed in

accordance with National Electric Code and local

codes and ordinances.

WARNING: Any receptacle replacement should be

performed by a qualified electrician.

A temporary 3-prong to 2-prong grounding adapter (see

Figure 7) is available for connecting plugs to a two pole

outlet if it is properly grounded.

Grounding Lug _ Make Sure This

-- - _ m.--..---rr is Connected

P,oapTer _''"_ _'t"_-J[I ToAKnown

3-Prong __ _.. J Ground

"/'_ _;_v't_'l _"_2-Prong Receptacle

Figure 7 - 2-Prong Receptacle with Adapter

• Do not use a 3-prong to 2-prong grounding adapter

unless permitted by local and national codes and

ordinances. (A 3-prong to 2-prong grounding adapter

is not permitted in Canada.)

Where a 3-prong to 2-prong grounding adapter is

permitted, the rigid green tab or terminal on the side

of the adapter must be securety connected to a

permanent electrical ground such as a properly

grounded water pipe, a properly grounded outlet box

or a properly grounded wire system.

• Many cover plate screws, water pipes and outlet

boxes are not properly grounded. To ensure proper

ground, grounding means must be tested by a quali-

fied electrician.

EXTENSION CORDS

• The use of any extensioncord willcause some drop

involtage and loss of power.

• Wires ofthe extensioncord mustbe ofsufficientsize

to carry the current and maintain adequate voltage.

• The minimum extension cord wire size is A.W.G. 14.

Do not use extension cords over 25 feet long.

• Use only 3-wire extension cords having 3-prong

grounding type plugs and 3-pole receptacles which

accept the tool plug.

• If the extension cord is worn, cut or damaged in any

way, replace it immediately.

MOTOR

Planerissuppliedwith a 2+/2HP motorinstalled.

The 120 Volt AC universalmotorhas the following

specifications:

Horsepower (Maximum Developed) .......... 2V2HP

Voltage ................................... 120

Amperes................................... 15

Hertz ..................................... 60

Phase.................................. Single

Cutterhead RPM .......................... 8000

ELECTRICAL CONNECTIONS

WARNING: Make sure unit is turned offand discon-

nected from powersource before inspectingany wiring.

The motoris installedand wiringconnected as illustrat-

ed in the wiringschematic (see Figure 8).

Switch

Black

Circuit

Breaker

Line Cord

Figureg- WiringSchematic

Motor

The motor is assembled with an approved three con-

ductor cord to be used on 120 volts as indicated. The

power supply to the motor is controlled by a double

pole locking switch.

The power lines are connected directly to the switch.

The green ground line must remain securely fastened

to the frame to properly protect against electrical shock.

A manual reset overload protector is installed in line

with the power suppry to the motor. If the planer is over-

loaded, the protector will break the circuit.

DESCRIPTION

Craftsman 13" planer finishes rough-cutlumber to size

and planes soft and hardwoods up to 6" thick and 13"

wide. Wood feeds into two-blade cutterhead by rubber

infeed/outfeed rollers. Sturdy base construction and

four-post design permits smoothfeeding and virtually

snipeless planing. Planer comes with enclosed, univer-

sal ball bearing, 2_/2HP (max. developed) motor with

overload protection. Motor has ON/OFF switch with

removable key to prevent accidental start-up. Unit fea-

tures rollercase lock for uniform thickness, power move-

ment control for rollercase, depth-of-cut gauge for con-

venient set-up, workpiece thickness pre-set gauge with

6 settings for consistent set-up, easy hands-free

replacement of blades for safety and minimized down-

time, built-in dust collector, top mounted rollers for

workpiece return, built-in carrying handles, cord wraps

for portability and folding infeed/outfeed rollers for

smooth operation. Planer takes cuts up to _/_"per pass

at 24 feet per minute. Inch height scale has graduations

in _A6"increments, and metric height scale has gradua-

tions in lmm increments.

MOTOR

Table Size ........................... 13" x 10%"

Blade Width ............................... 13"

Maximum Depth of Cut ..................... 3/32"

Cuts Per Minute ......................... 16,000

Dust CollectionPort......................... 2V2"

Overall Dimensions........ 21" H x 26_/2" W x 35V2"D

Motor ............... 2V2HP (max, dev,), 15A, 120V

Weight ................................. 97 Ibs

OPERATION SAFETY RULES

WARNING: For yourown safety,read all of the

instructions and precautionsbefore operatingtool

WARNING: Operation of any power toolcan resultin

foreignobjectsbeing thrown into eyes whichcan result

in severe eye damage. Always wear safety goggles

complying with United States ANSI Z87.1 (shown on

package) before commencing power tool operation.

CAUTION: Always observe the following safety pre-

cautions:

• Knowgeneral power tool safety.Make sure all pre-

cautions are understood (see pages 2, 3 and 6).

• Whenever adjusting or replacing any parts on planer,

turn switch OFF and remove plug from power source.

• Make sure all guards are properly attached and

securely fastened.

• Make sure all moving parts are free from interference.

• Always wear eye protection or face shield.

• Make sure blades are aligned and properly attached

to cutterhead.

• Do not plug in planer unless switch is in off position.

After turning switch on, allow planer to come to full

speed before operating.

• Keep hands clear of all moving parts.

• Do not force cut. Slowing or stalling will overheat

motor. Allow automatic feed to function properly.

• Use quality lumber. Blades last longer and cuts are

smoother with good quality wood.

• Do not plane material shorter than 15", narrower

than 3A",wider than 13" or thinner than '/8".

• Never make planing cut deeper than 3/,,.

• Maintain the proper relationships of infeed and out-

feed table surfaces and cutterhead blade path.

• Do not back the work toward the infeed table.

• Take precautions against kickback. Do not permit any-

one 1ostand or cross in line of cutterhead's rotation.

Kickback or thrown debris will travel in this direction.

• Turn switch off and disconnect power whenever plan-

er is not in use.

• Replace knives as they become damaged or dull.

• Keep planer maintained. Follow maintenance instruc-

tions (see pages 9 -11).

OPERATING CONTROLS

ON/OFF SWITCH

The ON/OFF switch (A) is located on the front of the

planer motor. To turn the planer ON, move the switch to

the up position. To turn the planer OFF, move the switch

to the down position.

Figure 9 - ON/OFF Switch

SWITCH LOCK

Refer to Figure 10, page 7.

The planer can be lockedfrom unauthorizeduse by

lockingthe switch.To lock the switch:

• Turn the switchto OFF positionand disconnect plan-

er from powersource.

• Pullthe key (A) out.The switch cannotbe turned on

with the key (A) removed.

NOTE: Shouldthe key (A) be removedfrom the switch

at the ON position,the switchcan be turned offbut

cannot be turned on.

Figure10 - Switch Lockand CircuitReset

• To replace key, slidekey intothe slot on switch until

it snaps.

CIRCUIT BREAKER

Refer to Figure 10.

The planer isequipped with a motorprotection device-

circuitbreaker. The breaker willautomaticallyshut the

planer offwhen excessive current is consumed.

Ifthe breaker is tripped, turn the planer off and reset

the circuitby pressingthe button(B).

CAUTION: Be sure to turn the planer off priorto reset-

tingthe circuitbreaker to avoid unintentionalstart-up of

the planer.

RAISING AND LOWERING ROLLERCASE

Refer to Figure 11.

The rellercase (A) containsthe motor,cutterhead and

dust collector.The depth-of-cut iscontrolledby raising

or lowering the rellercase. For rapid movementof the

rellercase, push up or down on lever (BI while motor is

running

WARNING: Do notattempt to engage power elevation

while planing.Keep handsclear of knobon top of

planer.

For precise movement, rotate handle with knob(C).

One complete rotationof handle willraise or lower

rollercaseby %6"

Figure 11 - Raise/Lower Rollercase

A rotationaldirection label with depth indicatoris pro-

vided on bothsides of the planer top.

The English/Metricscale (D) with pointerallowseasy

adjustment of relier case height.

DEPTH-OF-CUT GAUGE

Refer to Figure 11.

A spring loaded depth-of-cut gauge (E) is attached to

front of rollercase. The pointer on depth-of-cut gauge

accurately displays the depth-of-cut per pass when

workpieca is positioned below the gauge. Cranking the

handle (C) moves the rollercase down and the pointer

shows depth-of-cut up to 3/=,,

Recommended Maximum Depth-Of-Cut:

Hard/Softwood up to 6" wide:.................. %2"

Hard/Softwood 6-13" wide: ...................... V_e"

CAUTION: A 3/_,,depth-of -cuton hard, softwood

6-13" wide can be made. However, continuousopera-

tion at this set-up can cause premature motorfailure.

WORKPIECE THICKNESS PRE-SET GAUGE

Refer to Figure 12.

Figure 12 -Workpisce Thickness Pre-set Gauge

A sixposition workpiecethickness pre-setcontrolknob

(A) ismountedon rightside ofplaner.This knoballowsto

presetthe desiredfinished workpiecathicknessthatthe

planerwillproduce.Sixsettingsare provided:%", Y,",'/_",

_/,",1" and 1W'

Example: Plane a 2" thickworkpiece up to 1_/,".

• Raise or lowerrollercase until it is just above the

workpiece.

• Positionthe workpiece on the planer table belowthe

rollercase.

• Rotate knob (A) until 1V,"is indicated.

• The planer is nowset to stopthe roilercasewhen

the workpiecethicknessreaches 1V,".

NOTE: To reset for a differentdepth stop,gently raise

the rollercase byabout 2 rotations.Turn knob (A) to

desired set-up.

ROLLERCASELOCK

Refer to Figure 13.

The rollercase can be locked from any movement dur-

ing planing in order to guarantee uniform thickness. To

lock rollercase, pull down on lever (A).

Figure 13 - Ronercase Lock

To release rollercase, gently push up lever (A)

NOTE: The rollercasecan be raised or lowered when it

is locked by exerting excessivepressure on handle.

However, crankingthe handle when the rollercaseis

lockedwillwear downthe locking mechanism prema-

turely.

DEPTH OF CUT

Refer to Figure 14.

Thickness planing refers to the sizing of lumber to a

desired thicknesswhile creating a level surface parallel

to the opposite side of the board. Board thickness

whichthe planer will produce is indicated by the scale

(D), and depth-of-cut-gauge (El. Preset the planer to

the desired thickness of finished workpiece using knob

(F). See "Workpiece Thickness Pre-set Gauge", page 7.

Figure 14 - Depth-Of-Cut

Depth-of-cutis adjusted by raisingor lowering the

rollercase (A) using handle (C).

• Quality ofthicknessplaning depends on the opera-

tor's judgement about the depth of cut.

• Depth of cut depends on the width, hardness, damp-

ness, grain direction and grain structure of the wood.

• Maximum thickness of wood which can be removed

in one pass is 3/=,,for planing operations on work-

piece up to 6"wide. Workpiece must be positioned

away from the center line of the table to cut _/=".

• Maximum thickness of wood which can be removed

in one pass is _," for planingoperations on work-

piece from 6" up to 13" wide.

• For optimum planing performance, the depth of cut

should be less than '/1,".

• Board should be planed with shallow cuts until the

work has a level side. Once a level surface has been

created, flip the lumber and create parallel sides.

• Plane alternatesides until the desired thickness is

obtained.When halfof totaldepthofcut istakenfrom

each side,the boardwillhavea uniformmoisturecon-

tentand additionaldryingwillnotcause ittowarp.

• Depthof cut shouldbeshallowerwhen work iswider.

• When planing hardwood,take lightcuts or plane the

wood in thin widths.

• Make a test cut with a test piece and verifythe thick-

ness produced.

• Check accuracy of test cutpriorto workingon fin-

ished product.

AVOID DAMAGE TO BLADES

• Thickness planer is a precisionwoodworking

machine and shouldbe used on quality lumber only,

• Do not plane dirtyboards;dirt and small stones are

abrasive and willwear out blade,

• Removenailsand staples.Useplanerto cutwoodonly.

• Avoid knots.Heavilycress-grethedwood makes

knots hard. Knotscan come loose and jam blade.

CAUTION: Anyarticlethatencountersplaner blades

may be forciblyejected from planercreating riskofinjury,

PREPARE WORK

• Thickness planer works best when lumber has at

least one flat surface.

• Use surface planer or jointerto create a flat surface.

• Twistedor severely warped boards can jam planer.

Rip lumber in half to reduce magnitudeof warp.

• Work shouldbe fed intoplaner in same directionas

the grain of the wood. Sometimes grain will change

directions in middle of board. In such cases, if possi-

ble, cut board in middle before planing so grain

direction is correct.

CAUTION: Do not plane board which is less than 15"

long;force of cut couldsplitboard and cause kickback.

FEEDINGWORK

The planerissuppliedwithplaningbladesmountedinthe

cutterheadand infeedandoutfeedrollersadjustedtothe

correctheight.Planerfeed isautomatic;itwillvary slightly

depending on typeofwood.

• Feed rate refers to rate at which lumber travels

through planer.

• Operator is responsiblefor aligningwork so itwill

feed properly.

• Raise/lower rottercaseto produce the depth ol cut

desired.

• Stand on side towhich the handle is attached.

Figure15 - FeedingWork

• Boards longerthan 24" shouldhave additionalsup-

port from free standing materiat stands.

• Positionthe workpiece with the face to be planed on

top,

• Turnthe planer on.

• Rest board end on in-feed roller plate and direct

board into planer.

• Gently slideworkpiece intothe infeed side of the

planer until the infeed roller begins to advance the

workpiece.

• Let go of the workpieca and allow automatic feed to

advance the workpieca.

• Do not push/pull on workpiece. Move to the rear and

receive planed lumber by grasping itin same man-

ner as it was fed.

CAUTION: To avoid risk of injury due to kickbacks, do

not stand directly in line with front or rear of planer,

• Do not grasp any portion of board which has not

gone past out-feed roller.

• Repeat this operation on all boards which need to be

same thickness.

• Planer has return rollers (A) on top so assistant can

pass work back to operator.

Figure 16 - Return Rollers

NOTE: Assistantmustfollow same precautions as

operator.

• Surface thatthe planer willproducewill be smoother

ifshallowerdepth of cut isused.

Avoiding Snipe

• Snipe refers to a depression at either end of board

caused by an uneven force on cutterhead when work

is entering or leaving planer.

• Snipe will occur when boards are not supported

properly or when only one feed roller is in contact

with work at beginning or end of cut.

• To avoid snipe, gently push the board up while feed-

ing the work until the outfeed rotterstarts advancing

it.

Move to the rear and receive planed board by gently

pushing it up when the infeed roller looses contact

with the board.

• When planing more than one board of the same

thickness, butt boards together to avoid snipe.

• Snipe is more apparent when deeper cuts are taken.

• Feed work in direction of grain. Work fed against

grain will have chipped, splintered edges.

Planer willoperate best ifkept in good conditionand

properly adjusted.

CHECK FOR WORN BLADES

• Conditionof blades willaffect precisionof cut.

Observe quality of cutwhich planer producesto

check conditionof blades.

• Dull bladeswilltear, rather than sever woodfibers

and producefuzzy appearance.

• Raised grain willoccurwhen dull blades poundon

wood that has varying density.Raised edge willalso

be prm:luced where blades have been nicked.

REPLACE BLADES

Refer to Figures 17, 18 and 19.

WARNING: Always turn planer OFF and disconnect

from power source beforestarting any maintenance

work.

• Loosen and remove socket head bolts (A) from

blade cover (B) on the rear side of planer.Remove

blade cover.

Figure17 - RemoveBladeCover

• Carefully turn cutterhead by hand towards you until it

is stopped by the self-engaging latch.

• Loosen and remove six bolts from gib (C).

Figure 18 - Remove Gib Bolts

• Remove gib using two magnets (Figure 19)

provided.

NOTE: Magnets can be easily disengaged from gib by

tiltingthem to leftor right.

CAUTION: Blade edges are extremely sharp. Keep

fingers away from blades at all times.

• Blade is held on position by two pins. Gently lift old

blades from the pins using the two magnets. Do not

make contact with the blade using fingers. Use

magnets only.

Magnet

Blade

Latcx_kS

Figure19 - RemoveBlade

• Replace with new blade and carefully position iton

the two pins using thetwo magnets.

• Replace gib and align the holeson the gibwith

holeson the blade using the two magnets,

• Secure gib to cutterhead usingsix boltsremoved

earlier.

• Depress latch to release cutterhead. Release latch

when cutterhead can be turned by hand.

• Turn cutterhead by hand until itis stopped byself-

engaging latch,

• Remove gib and blade as mentionedearlier.

• Replace with new blade and replace giband secure

itas mentioned earlier.

• Replace blade cover and secure it usingsockethead

bolts.

BRUSHINSPECTION AND REPLACEMENT

WARNING: Turn planer offand disconnect from power

source. Brushlife depends on amount of load on motor,

Regularly inspectbrushes after 100 hours of use.

Brushes are locatedon either side of planer motor.

Figure 20 - Replace Brushes

• Loosen brush cap (not shown) and gently remove

brush from motor.

NOTE: Brushes are located on both front and rear

sides of planer.

• Replace brushes if spring (A) is damaged.

• Replace brushes if carbon (B) is worn.

• Replace brushes and tighten brush cap.

ADJUSTING ROLLERCASE LEVEL

Refer to Figures 21 and 22, pages 14 and 16.

The planer will produceuneven depthof cut (tapered

cut) if rollemase (Fig. 22, Key No. 59) is not parallel

with base (Fig. 21, Key No.48). To restoreparallelism of

rollercasewith base:

• Using a test piece, measure height of the taper.

• Turn planer offand disconnectfrom power source.

• Fold front and rear extensiontables.

• Lay planer carefully on itsback so that bottomside

of base is facing you.

• Loosentwo socket head bolts (Fig.21, Key No.62).

Loosen chain (Fig. 21, Key No.67) bysliding idler

bracket (Fig. 21, KeyNo. 60).

• Rotate elevationscrews as needed. Each turn of

screw will movethat side of rollercaseby _Aa".

• Retightenchain using idler bracket.Tighten socket

head boltssecurely.

• Set planer back on itsbase.

• Make a test cut toverify adjustment.

REPLACING V-BELT

Refer to Figures 21, 22 and 23, pages 14, 16 and 18.

Inadequate tension in V-belts (Fig 22, Key No. 28 and

Fig. 23, Key No. 78) will cause belts to slip from the pul-

leys. Loose belts must be replaced. To replace V-belts:

• Remove socket pan head screw and flat washer

(Fig. 21, Key Nos. 1 and 2). Pull handle off. Pull knob

(Fig. 21, Key No. 40) off.

• Remove four pan head screws (Fig. 21, Key No. 15)

from cover (Fig. 21, Key No. 10). Remove cover.

Remove right side cover (Fig. 21, Key No. 39).

• Remove V-belt (Fig. 22, Key No.28) by walkingthe

belt from both pulleys alternately. Gently pull the belt

while turning the pulleys at the same time. Repeat

with V-belt (Fig. 23, Key No. 78).

• Replace with new belts. Walk each belt onto the pul-

leys in the reverse manner as when removingthe

belts.

Make sure each of the belts are evenly seated all

the way on both pulleys.

Replace right side panel and knob. Replace cover

and secure with pan head screws. Replace handle

and secure with flat washer and pan head screw.

LUBRICATION

• Motor and cutterhead bearings are sealed and need

no lubrication.

Gears and elevation screws shouldbe cleaned of

debris and greased.

The table and extension tables can be coated with a

lubricant such as paste wax, to make the workpiece

feed smoother. Be sure the lubricant used does not

affect the ability to finish the workpiece with varnish,

sealer, etc. Do not use any siliconebase lubricants.

CLEAN PLANER

• Keepplaner cleanof anywood chips,dust,dirt ordebris.

• After 10 hours of operation, the chains and gears

should have wood chips, dust and old grease

removed.

• Use common automotive bearing grease to lubricate

all chains and gears. Be sure all chains and gears

have plenty of grease.

SYMPTOM

Snipe

(gouging at ends of board)

POSSIBLE CAUSE(S)

1.Dull blades

2.Inadequate supportof long boards

3.Uneven force on cutterhead

4.Rollercase not level with base

5.Lumber not butted properly

CORRECTIVE ACTION

1.Replace bladesper instructions,

See "Maintenance"

2,Support long boards.See "Avoiding Snipe"

3,Gently push board when board is in contact

withonlyonefeed roller,See "AvoidingSnipe"

4,Adjust rollercase

See "Adjusting Table Level"

5,Butt end to end each piece of stockas

boards pass through planer

Fuzzy grain Planing wood with a high moisture Remove high moisture content from woodby

content drying

Torn grain 1.Too heavy a cut 1.Review "Depth of Cut"

2.Blades cutting against grain 2.Review "Feeding Work"

3.Dull blades 3.Replace blades per instructions

See "Maintenance"

Rough raised grain 1.Dull blades 1.Replace blades per instructions.

See "Maintenance"

2.Too heavy a cut 2.Review "Depth of Cut"

3.Moisture content too high 3.Dry the wood or use dried wood

Uneven depth of cut Rollercase not level with planer Rollercase not level

side to side) base See "Adjusting Table Level"

Rollercase elevation adjusts

with difficulty

1.Sprockets or chain dirty

2.Elevation screws, columns dirty

3.Elevation screws worn

4.Friction between rollercase and

covers

5.Rollercase not parallelwith planer

base

6.Rollercase lockengaged

1.Clean and lubricate sprocketsand chain

2.Clean and lubricateelevationscrews, columns

3.Replace elevation screws

4.Clean and lubricate

5.Adjust rollercase

See "Adjusting Table Level"

6.Release rollercase lock

Board feeds inside, but stops 1.Outfeed rollers cannot rotate due 1.Clear the clogging, cleandust collector

moving past the outfeed roller to clogging of chips system. See "Clean Planer"

2.Too much pressure on the 2.Use support stands to support workpiece

cutterhead from long workpiece longer than 24". See "Recommended

Accessories"

Board thickness does not Indicator not set correctly Adjust indicator and tighten securely

match depth of cut scale

Chain jumping 1.Sprockets worn 1.Replace sprockets

2.Chain worn 2.Replace chain

Planer will not operate 1.No power to planer 11.Check power source by qualified electrician

2.Motor overload protection tripped !2.Turn planer off. Reset motor overload

protection. See "Overload Reset"

3.Defective or loose switch or wiring 3.Check switchand wiring by qualified

electrician

Belt slipping Loose belt Replace belt, see "Replacing V-Belt"

Rollercase connect be lowered Workpiece thickness gauge setting Reset thickness gauge setting,

restricts rollercase movements see "Workpiece Thickness Gauge"

SYMP/uM

Excessive dust in air

(gougingat ends of board)

Excessive fan noise

Motor overheats

Tripping circuit breaker or fuses

POSSIBLE CAUSE(S)

1.Leaking bag or hose connection

2.Collector bag leaks

1.Large debris or piece of wood in

fan housing

2.Loose fan

1.Motor overload

2.Improper motor cooling

1.Motor overload

2.Improper capacity of circuit breaker

or fuses

3.Dull blades

CORRECTIVE ACTION

1.Check collector bag connections. Check

collectorhose connections

2.Dust trapped under bag clamp or collector

bag not sealed on flange

1.Turn collector off and letdebris settlein

collector bag. Remove blade guard and

clear chamber

2.Remove blade cover and tighten bolt

(Fig. 22, Key No. 19)

1.Reduce depth ofcut

2.Clean sawdustfrom motor

1.Reduce depth of cut

2.Use proper capacity circuitbreaker or fuse

3.Replace blades

Model 351.217430

Figure 21 - Replacement Parts Illustration for Base

35 36

19 20 7 1_

26 27/4

28/_

j°

-_1

,, 22

KEY

NO.

PART NO.

16099.00

STD851006

16098.00

16100.00

00964.00

STD652005

20042.00

16610.00

18578.00

18623.00

18524.00

09637.00

16742.00

02783.00

16096.00

16101.00

18500.00

01903.00

18566.00

05285.00

18603.00

18581.00

18565.00

07339.00

18525.00

03069.00

18583.00

18580.00

07482.00

18554.00

18516.00

18555.00

00389.00

18564,00

18619.00

18344.00

DESCRIPTION

QTY.

6-1.0 x 20ram Socket Pan Head 2

Screw

6ram Flat Washer* 2

Pointer 1

Handle Assembly 1

6-1.0 x 6ram Set Screw 1

5ram LockWasher* 4

6 x 24ram Knurled Dowel Pin 2

Spring 1

Plug 1

Upper Cover 1

6 x 21mm Knurled Dowel Pin 2

Bushing 4

Roller 2

4 x 18mm Spring Pin 1

8-1.25 x 16ram Socket Pan Head 4

Screw

Grip 2

4-1.59 x 6ram Threadforming 8

Screw

4-0.7 x 10ram Pan Head Screw 2

Bracket 1

5-0.8 x 6ram Pan Head Screw 4

Spring 1

Pointer Bracket 1

Cable 1

6mm Steel Ball 1

Collar 2

5-0.8 x 6ram Set Screw 2

Pointer Guide 1

Pointer 1

5-0.8 x 18ram Socket Head Bolt 2

Pulley Bracket 1

Bushing 2

Cable Pulley 1

5-9.8 x 12mm Pan Head Screw 1

Left Side Cover 1

Tool Storage Case 1

5-1.6 x 12ram Threadforming 4

Screw

Shaft37 18597.00 1

Standard hardware item available locally

A Not Shown

KEY

! NO. PART NO.

38 16115.00

39 18591.00

40 18560.00

41 18616,00

42 18547.00

43 03855.00

44 00256.00

45 18526.00

46 18527.00

47 18534.00

48 18507.00

49 STD841217

50 STD833020

51 STD840610

52 18601.00

53 08662.00

54 09658.00

55 18615.00

56 00781.00

57 18563.00

58 18535.00

59 18590.00

60 18299.00

61 STD851005

62 05331.00

63 18339.00

64 18333.00

65 05148.00

66 18618.00

67 18522.00

68 18540.00

69 STD315505

70 18510.00

71 18332.00

72 18338.00

73 STD851004

74 20036.00

75 STD841015

76 18505.00

DESCRIPTION

Magnet

RightSide Cover

Knob

Table

Guide Plate

5-0.8 x 10ram Socket Head Bolt

3AMI-20 RetainingRing

FrontColumn

Rear Column

ElevatingScrew

Base

12-1.75mm Hex Nut*

6-1.0 x 20ram Hex Head Bolt*

6-1.0ram Hex Nut*

Spacer

6-1.0 x 8ram Socket Head Bolt

Bushing

Support Roller

4-0.7 x 8ram Pan Head Screw

Left Roller Plate

ExtensionTable

Right Roller Plate

Idler Bracket

5mm FlatWasher*

5-0.8 x 12mm Socket Head Bolt

Sprocket

Spacer

3AMI-8 Retaining Ring

Thickness Gauge

Chain

Gauge Bracket

6000ZZ Ball Bearing*

Bearing Retainer

Spacer

Sprocket

4ram Flat Washer*

4-0.7 x 12ram Socket Pan Head

Screw

10-1.5ram Hex Nut*

AdjustScrew

QTY.

Recommended Accessories

A Multi-Purpose Stand

A Horizontal Roller Stand

A Three-Roller Stand

9-22224

9-21417

9-22265

Model 351.217430

Figure 22 - Replacement Parts Illustration for Rollercase

11 12

14 15

47 48

21 25

2-_--'P--/

.d,--- 41

KEY

NO.

PART NO.

18506.00

03855.00

18514.00

18499.00

01784.00

18523.00

06731.00

18537.00

18349.00

18288.00

STD840812

STD852008

16383.00

06821.00

06396.00

18568.00

16129.00

16351.00

06346.00

STD851006

18536,00

18539.00

STD315505

18599.00

18533.00

00964.00

18538.00

18495.00

16125.00

16124.00

16123.00

16382.00

03069.00

20039.00

18573.00

00964.00

DESCRIPTION

Air Duct

5-0.8 x 10mm Socket Head Bolt

Blade Cover

4-1.4 x 12mm Flat Head

ThreadformingScrew

5-0,8 x 10ram Pan Head Screw

Chip Deflector

5-0.8 x 10ram Socket Pan Head

Screw

Fan Housing

6-1.0 x 25ram Socket Pan Head

Screw

Dust Chute

8-1.25mm Hex Nut*

8mm LockWasher*

Left Cam

3CM1-12 E-Ring

3 x 12mm Spring Pin

LockLever

Spring

LockLever Cap

6-1.0 x 12mm Socket Pan Head

Screw

6ram Flat Washer*

!Ean

i FanShaft

6000ZZ Ball Bearing*

Spacer

Dust Cover

6-1.0 x 6mm Set Screw

Fan Pulley

135J2 V-Belt

Rod

Spring

Pad

Right Cam

5-0,8 x 6ram Set Screw

Spring

Nut

6-1.0 x 6ram Set Screw

Standard hardware itemavailable locally

QTY.

KEY

NO.

PART NO.

18562.00

STD851005

08551,00

00814.00

18612.00

02702.00

18593.00

18513.00

18595.00

18589.00

05383.00

STD540501

00361.00

01474.00

18582.00

01548.00

STD851004

18579.00

18520.00

00781.00

18584.00

18574.00

18594.00

18494.00

18587.00

18636.00

18570.00

18571,00

02614,00

STD841015

18614.00

!18611.00

00533.00

STD851008

00483.00

18567.00

03853.00

03843.00

18585,00

DESCRIPTION QTY.

Left Elevating Nut 1

5ram Flat Washer* 1

Retainer Plate 1

5-0.8 x 16ram Socket Head Bolt 2

Outfeed Spring 2

Cord Clamp 1

Roller 2

Belt Guard 1

Screw 1

Right Elevating Nut 1

5-9.8 x 16mm Hex Head Bolt 5

5-0.8ram Hex Nut* 5

5-0.8 x 8ram Pan Head Screw 2

5ram Serrated Lock Washer 2

Pointer Cover 1

4-0.7 x 12ram Pan Head Screw 1

4mm Flat Washer* 1

Pointer 1

Bushing 1

4-0.7 x 8ram Pan Head Screw 2

PointerHousing 1

Nut 1

Rollercase 1

12mm Steel Ball 1

Retaining Plate 1

3-1.0 x 8ramThreadformingScrew 2

Magnet 4

Magnet Seat 4

5-0.8 x 10ram Flat Head Screw 4

10-1.5mm Hex Nut* 1

Stop Rod 1

InfeedSpring 2

3AM1-15 Retaining Ring 2

8ram Fiat Washer* 1

8-1.25 x 25mm Socket Head Bolt 1

Cable Clamp 1

Sprocket 2

RetainingBracket 4

Retainer 4

Model 351.217430

Figure 23 - Replacement Parts Illustration for Cutterhead and Gearing

48 55

\7 3

.76

77 78 79

2-.._

7 46

83 84

@ _X 87

KEY

NO. PART NO.

1 18517.00

2 18548.00

3 00221.00

4 03855.00

8 18516.00

6 16515.00

7 18545.00

8 18551.00

9 00256.00

10 03069.00

11 18546.00

12 ST0852005

13 18598.00

14 05331.00

15 STD315505

16 18510.00

17 18332.00

18 18338.00

19 ST0851004

20 20036.00

21 18606.00

22 06182.00

23 18549.00

24 18541.00

25 18622.00

26 ST0315525

27 18542.00

28 18613.00

29 18607.00

30 97339.00

31 18519.00

32 18621.00

33 06252.00

34 18553,00

35 18497.0O

36 22548,00

37 03853.00

38 06045.00

39 ST0851005

40 18608.00

41 18617.O0

42 18600.00

43 18502.00

44 15105.00

45 18575.00

DESCRIPTION

Bushing

Guide Rod

3AMI-10 Retaining Ring

5-0.8 x 10rnrn Socket Head Bolt

Bushing

Bracket

Grip

Handle

3AMI-20 Retaining Ring

6-0.8 x 6ram Set Screw

Guide Bracket

5mm LockWasher*

Sliding Bar

5-0.8 x 12rnrn Socket Head Bolt

6000ZZ Ball Bearing"

Bearing Retainer

Spacer

Sprocket

4rnrn Flat Washer*

4-0.7 x 12turn Socket Pan Head

Screw

Spring

6-1.0 x 30rnm Socket Head Bolt

Guide Rod

Gear

Transmission Seat

6002ZZ Ball Bearing"

Gear

Spring Holder

Spring

6mm Steel Ball

Bushing

Transmission Collar

5-0.8 x 14rnrn Socket Head Bolt

Holder

3AMI-24 Retaining Ring

Chain

Sprocket

5-0.8 x 20rnm Socket Head Bolt

5mrn Flat Washer*

Spring

Tension Wheel Assembly

Spacer

5-0.8 x 30turn Socket Head Bolt

5-0.8 x 35rnrn Socket Head Bolt

Outside Gear Plate

Standard hardware item available locally

A Not Shown

QTY.

KEY

NO.

PART NO. DESCRIPTION

20038.00

18596.00

18267.00

18351.00

18329.00

20020.00

18577.00

STD315225

18572.00

18266.00

18277.00

18330.00

18528.00

19069.00

16529.00

03839.00

18557.00

18602.00

9-29459

18543,00

09789.00

18512.00

ST0315245

18509.00

05331.00

18609.00

18531.00

20040,00

01784,00

18824,00

18832,00

18552,00

93841.00

00964,00

18530.00

18493,00

20041,00

16080,00

94287,00

20043,00

20044.00

20045.00

18625,00

20026,00

18236,03

QTY.

Sleeve 2

Shaft 1

58"1"/12TGear 1

70T Gear 1

Spacer 2

Inside Gear Plate 1

Pinion Gear 1

6202ZZ Ball Bearing* 1

Motor Pulley 1

52T/12T Gear 1

Bushing 5

Spacer 4

Cover 1

4 x4x 19mm Key 1

Cutterhead 1

5 x5x 10mm Key 1

Cutterhead Pin 4

Spring 4

Blade (Set of 2) 1

Gib 2

6-1.0 x 16turn Socket Pan Head 12

Screw

Bearing Retainer 1

6204ZZ Bail Bearing* 1

Bearing Cover 1

5-0.8 x 12mm Socket Head Bolt 3

Spring 1

Cutterhead Lock 1

Bushing 1

5-0.8 x 10mm Pan Head Screw 1

Spacer 1

Cutterhead Pulley 1

Pulley Retaining Nut 1

135J6 V-Belt 1

6-1.0 x 6rnrnSet Screw 1

Cutterhead Fan Pulley 1

Motor Assembly 1

Line Cord 1

Switch 1

Circuit Breaker 1

Brush Holder 2

Brush (set of 2) 1

Brush Cap 2

Half-Bag Dust Collection Set 1

Parts Bag 1

Operator's Manual 1

Page is loading ...

Your Home

For repair-in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems, ....

no matter who made it, no matter who sold it!

replacement parts accessories and .......

For the

s manuals that you need do it yourself

owner' to ....

For Sears professional installation of home appliances

....... and items like garage door openers and heaters....... water

..... 1 800 4 MY HOME ® (1coo4694663)

.... Call anytime , day or night (U.S .A. and Canada)

........ www sears com www sears ca .....,

Our Home

For repair of carry-in items like vacuums, lawn equipment, .....

, and electronics, call or go on-line for the location of your nearest .............

,...... Sears Parts & Repair Center. .....

...... 1 800 488 1222

m _ m ; ;;?

, ,:::* {2;i;

Call anytime, day or night (U.S.A. only) ........

....... www sears com .........

,,, To purchase a protection agreement on a product serviced by Sears: .....

...... 1-800- 827 m6655 (U.S.A .) 1-800 -361 -6665 (Canada) ,,

Pare pedir servicio de reparacidn Au Canada pour service en fran_ais:

a domicilio, y para ordenar piezas: 1-800-LE-FOYER Mc ......

.... 1 888 SU HOGAR s_ .....

(1600s336937) .....

_' (1 888 784 6427) sears ca

® Registered Trademark / TMTrademark / s_ Service Mark of Sears, Roebuck and Co.

® Marca Registrada / TMMarca de Fdbrica / s_ Marca de Servicio de Sears, Roebuck and Co.

Craftsman 351217430 Owner's manual

Brand: Craftsman

Model: 351217430

Category: Power planers

Type: Owner's manual

This manual is also suitable for

351.217430

Download PDF

report

in other languages

español: Craftsman 351217430 El manual del propietario

Craftsman 351217430 Owner's manual

This manual is also suitable for

Craftsman 351217430 Owner's manual

in other languages

Related papers

Other documents