Bosch PCQ875B21E/01 User manual

Brand: Bosch

Model: PCQ875B21E/01

Category: Hobs

Type: User manual

Page is loading ...

werden. Sowohl Kabeltyp als auch minimaler Querschnitt müs-

sen berücksichtigt werden.

Die Kochfelder werden mit Netzkabel mit oder ohne Stecker

geliefert.

Mit Stecker ausgestattete Geräte dürfen nur in vorschriftsmäßig

angebrachte, geerdete Steckdosen gesteckt werden.

Es muss ein allpoliger Trennschalter mit mindestens 3 mm Kon-

taktabstand angebracht werden (außer bei Anschluss an eine

frei zugängliche Steckdose).

Umstellung auf eine andere Gasart

Wenn die einschlägigen Bestimmungen des jeweiligen Landes

dies erlauben, kann dieses Gerät auf andere Gasarten umge-

stellt werden (siehe Typenschild). Die hierfür notwendigen Teile

befinden sich im mitgelieferten Umbaukit (je nach Modell) oder

können über den Kundendienst bezogen werden.

WICHTIG:Bringen Sie den Aufkleber mit der umgestellten Gas-

art in der Nähe des Typenschildes an.

Es müssen folgende Schritte befolgt werden:

A) Austausch der Düsen (Abb. 6):

1. Nehmen Sie die Roste, Brennerdeckel und Verteiler ab.

2. Tauschen Sie die Düsen mit dem über unseren Kundendienst

erhältlichen Schlüssel mit der Artikelnummer 340847 aus (für

Doppelbrenner und Dreiflammenbrenner Artikelnummer

340808), siehe Tabelle II. Achten Sie dabei besonders darauf,

dass die Düse beim Herausdrehen oder Befestigen am Bren-

ner nicht abbricht.

Stellen Sie sicher, sie bis zum Anschlag eingedreht zu haben,

um eine gute Abdichtung zu erreichen.

Bei diesen Brennern muss keine Einstellung der Primärluft vor-

genommen werden

3. Bringen Sie die Verteiler und Brennerdeckel auf den entspre-

chenden Kochstellen an und setzen Sie die Roste korrekt in

den entsprechenden Halteelementen ein.

B) Einstellung der Gashähne (Abb. 7):

1. Drehen Sie die Bedienknebel auf die niedrigste Stufe.

2. Ziehen Sie die Bedienknebel der Gashähne ab. Es wird eine

Knebeldichtung aus flexiblem Gummi sichtbar. Drücken Sie

diese mit der Schraubendreherspitze beiseite, um an die Ein-

stellschraube des Gashahns zu gelangen.

Bauen Sie die Knebeldichtungen niemals aus. Die Dichtun-

gen sind für den fehlerfreien Betrieb des Geräts unerlässlich,

da sie das Eindringen von Flüssigkeiten und Schmutz ins Ge-

räteinnere verhindern.

3. Stellen Sie die minimale Gaszufuhr ein, indem Sie die Bypass-

Schraube mit einem Schlitzschraubenzieher drehen.

Je nach Gasart, auf die Sie umstellen (siehe Tabelle III), müs-

sen entsprechende Schritte durchgeführt werden:

A: die Bypass-Schrauben ganz anziehen.

B: die Bypass-Schrauben bis zum korrekten Gasaustritt an den

Brennern lockern.

C: die Bypass-Schrauben müssen von einem autorisierten

Fachmann ausgetauscht werden.

D: nehmen Sie keine Veränderungen an den Bypass-Schrau-

ben vor.

Stellen Sie sicher, dass der Brenner bei einer Umstellung des

Bedienknebels von der höchsten auf die niedrigste Stufe nicht

ausgeht und nicht zurückschlägt.

Wenn Sie nicht an die Bypass-Schraube gelangen sollten,

bauen Sie die Fettauffangschale, die mit dem restlichen Koch-

feld verschraubt ist, aus. Zum Abnehmen gehen Sie wie folgt

vor:

1. Nehmen Sie alle Roste, Brennerdeckel, Verteiler und Bedien-

knebel ab.

2. Lockern Sie die Brenner-Schrauben.

3. Für den Wiedereinbau des Geräts folgen Sie den Ausbauan-

weisungen in umgekehrter Reihenfolge.

Bauen Sie niemals die Achse des Gashahns aus (Abb. 8). Bei

einer Störung den kompletten Gashahn ersetzen.

Installation instructions

Safety precautions

Read the appliance's instructions before installing and using.

The images shown in these instructions are for guidance only.

The manufacturer is exempt from all responsibility if the

requirements of this manual are not complied with.

This appliance must only be used in well ventilated places. It

must not be connected to a combustion product removal

device.

All operations relating to installation, connection, regulation

and conversion to other gas types must be carried out by an

authorised installation engineer, respecting all applicable

regulations, standards and the specifications of the local gas

and electricity suppliers. Special attention shall be paid to

ventilation regulations.

It is recommended you contact the Technical Assistance

Service to change to another gas type.

This appliance has been designed for home use only, not for

commercial or professional use. This appliance cannot be

installed on yachts or in caravans. The warranty will only be valid

if the appliance is used for the purpose for which it was

designed.

Before installing, you need to check that local distribution

conditions are compatible with the appliance's adjustment

indicated on the specifications plate (gas type and pressure,

power, voltage). See table I.

Before you begin, turn off the appliance's electricity and gas

supply.

The supply cable must be attached to the unit to prevent it from

touching hot parts of the oven or hob.

Appliances with electrical supply must be earthed.

Do not tamper with the appliance's interior. If necessary, call our

Technical Assistance Service.

Before installing

This appliance is class 3 type, according to the EN 30-1-1

regulation for gas appliances: built-in appliance.

The kitchen unit in which the appliance is installed must be

properly secured and stable.

The kitchen units next to the appliance, the laminated covering

and glue for adhering it must be made of non-flammable and

heat-resistant materials.

This appliance cannot be installed above fridges, washing

machines, dishwashers or similar.

An oven must have forced ventilation to install a hob above it.

Check the dimensions of the oven in the installation manual.

If an extractor fan is installed, you must follow the instructions in

the installation manual, always respecting the minimum vertical

distance from the hob (fig. 1).

Preparation of the kitchen unit (fig. 1-2)

Make an appropriate size cut in the worktop surface, depending

on the installation method. standard (a) or flush (b). For flush

installation:

■ All cuts in the worktop surface should be done by a

specialised shop.

■ The cuts should be clean and precise, as the cut edge is on

the surface. The stability of the furniture should also be

ensured after cutting work.

■ Use only specially designed work surfaces, resistant to high-

temperature and water (e.g. natural stone or tiled).

■ Surrounding furniture must be resistant to temperatures up to

90 °C.

If the hob is electric or mixed (gas and electricity) and there is

no oven below, place a non-flammable separator (e.g. metal or

plywood) 10 mm from the bottom of the hob. This will prevent

access to the base of the hob.If the hob is gas, it is

recommendable to place the separator at the same distance.

On wood work surfaces, varnish the cutting surfaces with a

special glue. This protects them from moisture which could

collect under the work surface.

Installation of appliance

Note: Wear protective gloves to fit the hob.

A) Standard installation (fig. 3a)

Depending on the model, the adhesive seal may be factory-

fitted. If this is the case, it should not be removed under any

circumstances, since the adhesive seal prevents leaks. If the

seal has not been factory-fitted, apply it to the underside of the

hob.

Fitting the appliance onto the kitchen unit:

1. Remove the clips from the accessory bag and screw them into

the position indicated so that they can turn freely.

2. Insert and centre the hob.

Press the sides of the hob until it is supported around its entire

perimeter.

3. Turn the clips and tighten them fully.

The position of the clips depends on how thick the work

surface is.

B) Flush installation (fig. 3b)

1. Complete a normal installation of the appliance making sure

that it is surrounded by a uniform slot. The hob surface should

be slightly below the work surface.

For tile worktops, if necessary, raise the bearing surfaces with

strips resistant to water and temperatures.

2. Check the operation and position of appliance.

3. Fill the gap between the worktop and hob with conventional

silicone adhesive appropriate in the colour you desire.

Note: If unsuitable silicone adhesive is used on natural stone

surfaces then this can produce colours that can not be

removed. Our Technical Assistance Service can provide you

with the most suitable glue (code 310818). Please note the

manufacturers instructions for use.

4. Smooth the silicone adhesive with a scraper or wet finger

moistened with soap and water before it forms a layer.

5. Allow the silicone adhesive to dry before using the appliance.

Removal of hob

Turn off the appliance's electricity and gas supply.

Unscrew the clips and proceed in the reverse order to

installation.

Gas connection (fig. 4)

The gas connection must be located in a position where the

stop tap is accessible.

The end of the inlet connection point of the gas hob has a 1/2”

thread (20.955 mm) that allows for:

■ A fixed connection.

■ Connection using a flexible pipe (L min. 1 m - max. 3 m).

The watertight seal (034308) supplied must be inserted

between the manifold outlet and the gas supply.

You must prevent the pipe from coming into contact with

moving parts of the kitchen unit (for example, a drawer) and

prevent access to any spaces which might become obstructed.

Do not move the L-tube from the factory-fitted position,

regardless of the connection type.

If you need to make a cylindrical connection, replace the factory-

fitted L-tube with the one in the accessory bag. Fig. 4a.

Please remember to insert the seal.

: Danger of leaks!

If any connection is handled, check the seal.

The manufacturer is not liable for any connection leaking, after

being handled.

Electric connection (fig. 5)

This appliance is type “Y”: the supply cable can only be

changed by the Technical Assistance Service and not the user.

The cable type and minimum cross-section must be respected.

The hobs are supplied with a power cable with or without a wall

socket plug.

Appliances with plugs must only be connected to sockets that

have earth wires correctly installed.

Provide an omnipolar cut-off switch with a minimum contact

opening of 3 mm (except for plug connections, if the user has

access to it).

Changing the gas type

If the country's regulations allow, this appliance can be adapted

to other types of gas (see specifications plate). The components

required for this are in the transformation kit supplied

(depending on the model) or are available from our Technical

Assistance Service.

Important: After finishing, stick the sticker, indicating the new

gas type, close to the specifications plate.

The following steps should be taken:

A) Changing the nozzles (fig. 6):

1. Remove the pan supports, burner caps and diffusers.

2. Change the nozzles using the spanner code 340847 (code

340808 for double-flame burners or triple-flame burners)

provided by our Technical Assistance Service, see table II,

taking special care to ensure that the nozzle does not fall

when it is removed from or fitted to the burner.

Ensure that it is completely tightened in order to guarantee the

seal.

Primary air adjustment is not necessary with these burners.

3. Position the diffusers and burner caps on the corresponding

rings and the pan supports on their fasteners.

B) Adjusting the taps (Fig. 7):

1. Set the control knobs to minimum.

2. Remove the control knobs from the taps. It has a flexible

rubber valve reinforcing ring. Press with the tip of the

screwdriver to access the tap's adjusting screw.

Never remove the valve reinforcing ring. The valve reinforcing

rings guarantee the watertightness of the appliance's interior

from liquids and dirt, which might otherwise prevent its correct

operation.

3. Adjust the minimum ring setting by turning the by-pass screw

using a flat head screwdriver.

Depending on the gas to which your appliance is going to be

adapted, see table III, carry out the corresponding action:

A: firmly tighten the by-pass screws.

B: loosen the by-pass screws until the gas flow from the

burners is correct.

C: the by-pass screws need to be changed by an authorised

engineer.

D: do not touch the by-pass screws.

When adjusting the control knob between maximum and

minimum, the burner does not go out, nor is there a flame

backdraught created.

If the by-pass screw cannot be accessed, disassemble the

grease drip tray, which is fitted to the hob with a series of

screws. The following steps must be taken to remove it:

1. Remove all pan supports, burner caps, diffusers and control

knobs.

2. Remove the screws from the burners.

3. To reinstall the appliance, proceed in the reverse order to

disassembly.

Never remove the tap spindle (Fig. 8). In the event of a

malfunction, change the whole tap.

Instrucciones de montaje

Indicaciones de seguridad

Lea las instrucciones del aparato antes de proceder a su

instalación y uso.

Las imágenes representadas en estas instrucciones tienen

carácter orientativo.

El fabricante queda exento de toda responsabilidad si no se

cumplen las disposiciones de este manual.

Este aparato se debe utilizar únicamente en lugares

suficientemente ventilados. No se debe conectar a un

dispositivo de evacuación de los productos de combustión.

Todos los trabajos de instalación, conexión, regulación y

adaptación a otros tipos de gas deben ser efectuados por un

técnico de instalación autorizado, respetando toda la

normativa y legislación aplicables y las prescripciones de las

compañías locales proveedoras de gas y electricidad. Se

pondrá especial atención a las disposiciones aplicables en

cuanto a la ventilación.

Se recomienda llamar a nuestro Servicio Técnico para la

adaptación a otros tipos de gas.

Este aparato ha sido diseñado solo para uso doméstico, no

estando permitido su uso comercial o profesional. Este aparato

no puede ser instalado en yates o caravanas. La garantía

únicamente tendrá validez en caso de que se respete el uso

para el que fue diseñado.

Antes de la instalación, compruebe que las condiciones de

distribución local son compatibles con el reglaje del aparato

que figura en la placa de características (naturaleza y presión

del gas, potencia, voltaje). Ver tabla I.

Antes de cualquier actuación corte la alimentación eléctrica y

de gas del aparato.

El cable de alimentación debe fijarse al mueble para evitar que

toque partes calientes del horno o placa de cocción.

Los aparatos con alimentación eléctrica deben conectarse a

tierra obligatoriamente.

No manipule el interior del aparato. Si es preciso, llame a

nuestro Servicio Técnico.

Antes de la instalación

Este aparato corresponde a la clase 3, según la norma EN 30-

1-1 para aparatos a gas: aparato encastrado en un mueble.

Page is loading ...

Bosch PCQ875B21E/01 User manual

Brand: Bosch

Model: PCQ875B21E/01

Category: Hobs

Type: User manual

Download PDF

report

in other languages

italiano: Bosch PCQ875B21E/01 Manuale utente
français: Bosch PCQ875B21E/01 Manuel utilisateur
español: Bosch PCQ875B21E/01 Manual de usuario
Deutsch: Bosch PCQ875B21E/01 Benutzerhandbuch
Nederlands: Bosch PCQ875B21E/01 Handleiding
português: Bosch PCQ875B21E/01 Manual do usuário
Türkçe: Bosch PCQ875B21E/01 Kullanım kılavuzu

Bosch PCQ875B21E/01 User manual

Bosch PCQ875B21E/01 User manual

in other languages

Related papers

Other documents