Whirlpool WGD4800XQ Installation guide

1

W10514185A

W10514176A-SP

Table of Contents

DRYER SAFETY ................................................................2

INSTALLATION REQUIREMENTS ....................................4

Tools and Parts .................................................................... 4

Location Requirements ...................................................... 4

ELECTRIC DRYER POWER HOOKUP – CANADA ONLY ......... 6

Electrical Requirements ..................................................... 6

Install Leveling Legs ........................................................... 6

GAS DRYER POWER HOOKUP ................................................. 7

Gas Supply Requirements .................................................. 7

Electrical Requirements ..................................................... 9

VENTING ...................................................................................... 9

Venting Requirements ......................................................... 9

Plan Vent System ............................................................... 10

Venting Kits ........................................................................ 11

Install Vent System ............................................................ 12

Make Gas Connection ...................................................... 12

Connect Vent ..................................................................... 13

LEVEL DRYER ........................................................................... 13

COMPLETE INSTALLATION CHECKLIST ............................... 13

REVERSE DOOR SWING (OPTIONAL) .................................... 14

TROUBLESHOOTING ............................................................... 21

INSTALLATION NOTES

Date of purchase: _________________________________

Date of installation: _______________________________

Installer: ________________________________________

Model number: ___________________________________

Serial number: ___________________________________

Date d’achat : _____________________________________

Date d’installation : ________________________________

Installateur : ______________________________________

Numéro de modèle : ________________________________

Numéro de série : __________________________________

NOTES CONCERNANT L’INSTALLATION

Table des matières

SÉCURITÉ DE LA SÉCHEUSE ....................................... 22

EXIGENCES D’INSTALLATION ...................................... 24

Outillage et pièces ............................................................ 24

Exigences d’emplacement ............................................... 25

RACCORDEMENT À L’ALIMENTATION ÉLECTRIQUE

DE LA SÉCHEUSE ÉLECTRIQUE – CANADA SEULEMENT ... 27

Spécications électriques ................................................ 27

Installation des pieds de nivellement .............................. 28

RACCORDEMENT D’UNE SÉCHEUSE À GAZ ....................... 28

Spécications de l’alimentation en gaz .......................... 28

Spécications électriques ................................................ 30

L’ÉVACUATION.......................................................................... 30

Exigences concernant l’évacuation ................................ 30

Planication du système d’évacuation ........................... 31

Trousses d’évacuation ...................................................... 32

Installation du circuit d’évacuation ................................. 33

Raccordement au gaz ....................................................... 34

Raccordement du conduit d’évacuation ......................... 34

RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE......................... 35

ACHEVER L’INSTALLATION – LISTE DE VÉRIFICATION ....... 35

INVERSION DU SENS DE L’OUVERTURE DE LA PORTE

(FACULTATIF)

............................................................................. 36

DÉPANNAGE ............................................................................. 44

DRYER INSTALLATION INSTRUCTIONS

29" and 27" Wide Models

Gas (U.S.A. and Canada) & Electric (Canada Only)

INSTRUCTIONS D’INSTALLATION DE LA SÉCHEUSE

Modèles de 29" et de 27" de largeur

À gaz (É.-U. et Canada) et Électrique (Canada uniquement)

Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite:

www.whirlpool.com

Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta.

Page is loading ...

4

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed for all installations:

Level

Tape measure

Pliers

Parts package is located in dryer drum. Check that all parts

are included.

Parts needed:

Check local codes. Check existing electrical supply and venting.

See “Electrical Requirements” and “Venting Requirements”

before purchasing parts.

Check code requirements. Some codes limit, or do not permit,

installing dryer in garages, closets, mobile homes, or sleeping

quarters. Contact your local building inspector.

Optional Equipment: (Not supplied with dryer)

Refer to your “Use and Care Guide” for information about

accessories available for your dryer.

Parts supplied:

Flat-blade screwdriver

#2 Phillips screwdriver

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

Tin snips (new vent

installations)

Caulking gun and

compound (for installing

new exhaust vent)

Vent clamps

1/4" nut driver or socket

wrench (recommended)

Leveling legs (4)

Tools needed for gas installations:

8" or 10" pipe wrench

8" or 10" adjustable wrench

(for gas connections)

Pipe-joint compound

resistant to LP gas

Utility knife

Location Requirements

You will need:

■ A location allowing for proper exhaust installation.

See “Venting Requirements.”

INSTALLATION REQUIREMENTS

Putty knife

5

Installation Spacing

A

B

C

18"*

(457 mm)

1"

(25 mm)

29"

(737 mm)

1"

(25 mm)

1"*

(25 mm)

14" max.*

(356 mm)

27¾"

(705 mm)

48 in.

(310 cm )

2

*

2

3"*

(76 mm)

3"*

(76 mm)

24 in.

(155 cm )

2

*

2

A. Recessed area

B. Side view – closet or conned area

C. Closet door with vents

*Required spacing

29" Wide Models

Dryer Dimensions

A. Wide opening side-swing door

B. Wide opening hamper door

A B

Installation clearances:

The location must be large enough to allow the dryer door to

open fully.

Most installations require a minimum 5½" (140 mm) clearance

behind the dryer for the exhaust vent with elbow. See “Venting

Requirements.”

■ A separate 30 amp circuit for electric dryers.

■ A separate 15 or 20 amp circuit for gas dryers.

■ If you are using power supply cord, a grounded electrical

outlet located within 2 ft. (610 mm) of either side of dryer.

See “Electrical Requirements.”

■ A sturdy oor to support dryer and a total weight (dryer

and load) of 200 lbs. (90.7 kg). The combined weight of a

companion appliance should also be considered.

■ Level oor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), install Extended

Dryer Feet Kit, Part Number 279810. If not level, clothes

may not tumble properly and automatic sensor cycles may

not operate correctly.

Do not operate your dryer at temperatures below 45°F (7°C).

At lower temperatures, the dryer might not shut off at the end

of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

Mobile home – Additional installation requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280) or the Canadian

Manufactured Home Standard CAN/CSA-Z240 MH.

■ Metal exhaust system hardware, available for purchase.

For further information, please reference the “Assistance

or Service” section of the “Use and Care Guide.”

■ Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such

as a nearby window) should be at least twice as large

as the dryer exhaust opening.

27" Wide Models

Dryer Dimensions

43"

(1092 mm)

27"

(686 mm)

A

23¾"

(603 mm)

43"

(1092 mm)

27"

(686 mm)

*29

1

/

2

"

(749 mm)

13¾"

(349 mm)

B

*29

1

/

2

"

(749 mm)

A. Large opening side-swing door

B. Wide opening hamper door

Installation Spacing

A

B

C

18"*

(457 mm)

1"

(25 mm)

27"

(686 mm)

1"

(25 mm)

1"*

(25 mm)

14" max.*

(356 mm)

29

½

"

(749 mm)

5

½"*

(140 mm)

48 in.

(310 cm )

2

*

2

24 in.

(155 cm )

2

*

2

3"*

(76 mm)

3"*

(76 mm)

A. Recessed area

B. Side view – closet or conned area

C. Closet door with vents

*Required spacing

Installation spacing for recessed area or closet

The dimensions shown are for the minimum spacing allowed.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door, and

oor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

■ Companion appliance spacing should also be considered.

6

Install Leveling Legs

Prepare dryer for leveling legs

1.

To avoid damaging oor, use a large at piece of cardboard

from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING:

Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

ELECTRIC DRYER POWER

HOOKUP – CANADA ONLY

Electrical Requirements

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate

and in conformance with the Canadian Electrical Code,

C22.1-latest edition and all local codes. A copy of the

above codes standard may be obtained from: Canadian

Standards Association, 178 Rexdale Blvd., Toronto, ON

M9W 1R3 CANADA.

■ To supply the required 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply on a separate 30-amp

circuit, fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual

branch circuit.

■ This dryer is equipped with a CSA International Certied

Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is 5 ft. (1.52 m) in length. Be sure

wall receptacle is within reach of dryer’s nal location.

4-wire receptacle (14-30R)

■ Do not use an extension cord.

If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

8579325. For further information, please reference the

“Assistance or Service” section of the “Use and Care Guide.”

7

Screw in leveling legs

2.

Examine leveling legs and nd diamond marking. Screw legs

into leg holes by hand. Use a wrench to nish turning legs

until diamond marking is no longer visible.

Now stand the dryer on its feet. Slide the dryer until it is

close to its nal location. Leave enough room to connect the

exhaust vent.

For mobile home use

Gas dryers must be securely fastened to the oor.

Mobile home installations require a Mobile Home Installation

Hold-down Kit. For ordering information, please reference the

“Use and Care Guide.”

diamond

marking

GAS DRYER POWER HOOKUP

Gas Supply Requirements

Gas type

Natural gas:

This dryer is equipped for use with Natural Gas. It is design-

certied by CSA International for LP (propane or butane) gases

with appropriate conversion.

■ Your dryer must have the correct burner for the type of gas

in your home. Burner information is located on the rating

plate in the door well of your dryer. If this information does

not agree with the type of gas available, please reference the

“Assistance or Service” section of the “Use and Care Guide.”

LP gas conversion:

Conversion must be made by a qualied technician.

No attempt shall be made to convert the dryer from the gas

specied on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier.

IMPORTANT: The gas installation must conform with local codes,

or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and

Propane Installation Code, CSA B149.1.

8

Gas supply line

■ 1/2" NPT pipe is recommended.

■ 3/8" approved tubing is acceptable for lengths under

20 ft. (6.1 m) if local codes and gas supplier permit.

■ Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer (see illustration).

■ Must include a shut-off valve:

In the U.S.A.:

An individual manual shut-off valve must be installed within

six (6) feet (1.8 m) of the dryer in accordance with the

National Fuel Gas Code, ANSI Z223.1.

In Canada:

An individual manual shut-off valve must be installed in

accordance with the B149.1, Natural Gas and Propane

Installation Code. It is recommended that an individual

manual shut-off valve be installed within six (6) feet (1.8 m)

of the dryer.

The shut-off valve location should be easy to reach for opening

and closing.

A

B

E

D

C

A. 3/8" exible gas connector

B. 3/8" pipe to are adapter tting

C. 1/8" NPT minimum plugged tapping

D. 1/2" NPT gas supply line

E. Gas shut-off valve

Gas supply connection requirements

There are many methods by which your gas dryer can be

connected to the gas supply. Listed here are some guidelines

for two different methods of connection.

This dryer must be connected to the gas supply line with

a listed exible gas connector that complies with the standard

for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

Option 1 (Recommended Method)

Flexible stainless steel gas connector:

■ If local codes permit, use a new exible stainless steel gas

connector (Design Certied by the American Gas Association

or CSA International) to connect your dryer to the rigid gas

supply line. Use an elbow and a 3/8" are x 3/8" NPT adapter

tting between the stainless steel gas connector and the

dryer gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method)

Approved aluminum or copper tubing:

■ Lengths over 20 ft. (6.1 m) can use 3/8" approved tubing

(if codes and gas supplier permit).

■ If you are using Natural Gas, do not use copper tubing.

■ 3/8" are x 3/8" NPT adapter tting between dryer pipe

and 3/8" approved tubing.

■ Lengths over 20 ft. (6.1 m) should use larger tubing and

a different size adapter tting.

■ If your dryer has been converted to use LP gas, 3/8" LP

compatible copper tubing can be used. If the total length

of the supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe joint compounds that resist the action of LP

gas must be used. Do not use TEFLON

®†

tape.

Dryer gas pipe

■ The gas pipe that comes out through the rear of your dryer

has a 3/8" male pipe thread.

29" Wide Model

A

1¼"

(32 mm)

9¼"

(235 mm)

A. 3/8" NPT dryer pipe

27" Wide Model

A

A. 3/8" NPT dryer pipe

*5

3

/4"

(146 mm)

1

/2"

(38 mm)

A. 3/8" NPT dryer pipe

Burner input requirements

Elevations up to 10,000 ft. (3,048 m):

■ The design of this dryer is certied by CSA International for

use at altitudes up to 10,000 ft. (3,048 m) above sea level at

the B.T.U. rating indicated on the model/serial number plate.

Burner input adjustments are not required when the dryer is

operated up to this elevation.

Elevations above 10,000 ft. (3,048 m):

■ When installed above 10,000 ft. (3,048 m), a 4% reduction

of the burner B.T.U. rating shown on the model/serial

number plate is required for each 1,000 ft. (305 m)

increase in elevation.

Gas supply pressure testing

■ The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2 psi.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

9

Electrical Requirements

■

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

re, or electrical shock.

WARNING

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate

circuit serving only this dryer be provided.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

VENTING

Venting Requirements

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or exible metal vent shall be used for

exhausting.

■ Only a 4" (102 mm) heavy metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may result

in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 7

3

/

4

ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or exible metal vents. Review “Vent System Chart” and,

if necessary, modify existing vent system to achieve best drying

performance.

4"

(102 mm)

4" (102 mm) heavy metal exhaust vent

10

Exhaust hoods:

■ Must be at least 12" (305 mm) from ground or any object

that may obstruct exhaust (such as owers, rocks, bushes,

or snow).

Elbows:

■ 45° elbows provide better airow than 90° elbows.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

See “Venting Kits” for more information.

Plan Vent System

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

B

C

D

E

F

G

H

I

A

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or exible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

I. Optional side exhaust outlet

Optional exhaust installations:

27" Wide Models can be converted to exhaust out the right side,

left side, or through the bottom (4-way vent kit). Each kit includes

step-by-step instructions. For ordering information, see “Venting

Kits.”

A. Standard rear offset exhaust installation

B. Left- or right-side exhaust installation

(27" wide models only)

C. Bottom exhaust installation (27" wide models only)

A B C

Recommended Styles:

Acceptable Style:

Louvered hood Box hood

Angled hood

Good

Better

11

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best

for your installation. Two close-clearance installations are shown.

Refer to the manufacturer’s instructions.

Over-The-Top installation (also available with one offset elbow)

Periscope installation

NOTE: The following kits for close clearance alternate

installations are available for purchase.

Venting Kits

For more information, call 1-800-901-2042, or visit us

at www.applianceaccessories.com. In Canada, call

1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Part Number Descriptions

8171587RP 0–5" Metal vent periscope

4396037RP 0"–18" Metal vent periscope

4396011RP 18"–29" Metal vent periscope

4396014 29"–50" Metal vent periscope

4392892 In-Wall metal DuraVent™ Periscope

W10186596 4-way vent kit – universal grey (27" Dryers Only)

4396028 Sure Connect™ venting kit

(over-the-top installation)

4396009RP 5' Universal connect vent, exible dryer venting

4396010RP 6' SecureConnect™ vent, exible dryer venting

4396013RB Dryer vent installer’s kit

4396033RP 5' exible dryer venting with clamps

4396727RP 8' exible dryer venting with clamps

4396004 Dryer offset elbow

4396005 Wall offset elbow

4396006RW DuraSafe™ close elbow

4396007RW Through-the-wall vent cap

4396008RP 4" steel dryer venting clamps – 2 pack

8212662 Flush mounting louvered vent hood 4"

Special provisions for mobile home installations:

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path:

■ Select route that will provide straightest and most direct path

outdoors.

■ Plan installation to use fewest number of elbows and turns.

■ When using elbows or making turns, allow as much room

as possible.

■ Bend vent gradually to avoid kinking.

■ Use as few 90° turns as possible.

Determine vent length and elbows needed for best

drying performance:

■ Use following “Vent System Chart” to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specied

in “Vent System Chart.” Exhaust systems longer than those

specied will:

■ Shorten life of dryer.

■ Reduce performance, resulting in longer drying times and

increased energy usage.

Vent System Chart

Number of

90° turns or

elbows

Type

of vent

Box/louvered

hoods

Angled

hoods

1

4

3

2

0

Rigid metal

64 ft. (20 m)

54 ft. (16.5 m)

44 ft. (13.4 m)

35 ft. (10.7 m)

27 ft. (8.2 m)

58 ft. (17.7 m)

48 ft. (14.6 m)

38 ft. (11.6 m)

29 ft. (8.8 m)

21 ft. (6.4 m)

The “Vent System Chart” provides venting requirements that

will help achieve best drying performance.

NOTE: Side and bottom exhaust installations for 27" wide

models have a 90º turn inside the dryer. To determine

maximum exhaust length, add one 90º turn to the chart.

12

Install Vent System

12" min.

(305 mm)

12" min.

(305 mm)

Install exhaust hood

1.

Install exhaust hood and use caulking compound to seal

exterior wall opening around exhaust hood.

A

B

C

D

Plan pipe tting connection

2.

A combination of pipe ttings must be used to connect dryer

to existing gas line. A recommended connection is shown.

Your connection may be different, according to supply line

type, size, and location.

A. 3/8" exible gas connector

B. 3/8" dryer pipe

C. 3/8" to 3/8" pipe elbow

D. 3/8" pipe-to-are adapter tting

Open shut-off valve in supply line; valve is open when handle

is parallel to gas pipe. Then, test all connections by brushing

on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leaks found.

†®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

Connect vent to exhaust hood

2.

Vent must t over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location

using straightest path possible. Avoid 90° turns. Use clamps

to seal all joints. Do not use duct tape, screws, or other

fastening devices that extend into interior of vent to secure

vent, because they can catch lint.

A

B

Connect gas supply to dryer

1.

Remove red cap from gas pipe. Using a wrench to tighten,

connect gas supply to dryer. Use pipe-joint compound

on threads of all non-ared male ttings. If exible metal

tubing is used, be sure there are no kinks.

NOTE: For LP gas connections, you must use pipe-joint

compound resistant to action of LP gas. Do not use

TEFLON

®†

tape.

Make Gas Connection

Vent System Chart

(29" Wide Long Vent Models Only)

Number of

90° turns

or elbows

Type

of vent

Box/louvered, or

Angled hoods

1

4

3

2

0

Rigid metal

120 ft. (36.6 m)

110 ft. (33.5 m)

100 ft. (30.5 m)

90 ft. (27.4 m)

80 ft. (24.4 m)

Rigid metal

5 70 ft. (21.3 m)Rigid metal

Open shut-off valve

3.

A

B

Closed valve

Open valve

Non-ared

male tting

Flared

male tting

13

Connect Vent

Connect vent to exhaust outlet

1.

Move dryer to nal location

2.

Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure vent is

clean. Dryer vent must t over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 4" (102 mm) clamp.

Move dryer to nal location. Avoid crushing or kinking vent.

After dryer is in place, remove corner posts and cardboard

from under the dryer.

Level Dryer

Level dryer

1.

Not Level LEVEL Not Level

Check levelness of dryer from side to side. Repeat from

front to back.

NOTE: The dryer must be level for the moisture sensing system

to operate correctly.

Tighten and adjust leveling legs

2.

If dryer is not level, prop up using a wood block. Use wrench

to adjust legs up or down, and check again for levelness.

Once legs are level, make sure all four legs are snug against

the oor before tightening them.

Complete Installation Checklist

q

Check that all parts are now installed. If there is an extra

part, go back through steps to see what was skipped.

q

Check that you have all of your tools.

q

Dispose of/recycle all packaging materials.

q

Check dryer’s nal location. Be sure vent is not crushed

or kinked.

q

Check that dryer is level. See “Level Dryer.”

q

Remove lm on console and any tape remaining on dryer.

q

Wipe dryer drum interior thoroughly with a damp cloth to

remove any dust.

q

Read “Dryer Use” in your “Use and Care Guide.”

q

Set the dryer on a full heat cycle (not an air cycle) for

20 minutes and start the dryer.

If the dryer will not start, check the following:

■ Dryer is plugged into a grounded 3-prong outlet.

■ Electrical supply is connected.

■ Household fuse is intact and tight, or circuit breaker

has not tripped.

■ Dryer door is closed.

q

When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. If you feel heat, cancel cycle

and close the door.

If you do not feel heat, turn the dryer off and check to see

whether gas supply line shut-off valve is open.

■ If the gas supply line shut-off valve is closed, open it,

then repeat the 5-minute test as outlined above.

■ If the gas supply line shut-off valve is open, contact a

qualied technician.

NOTE: You may notice an odor when the dryer is rst heated.

This odor is common when the heating element is rst used.

The odor will go away.

14

Reverse Door Swing (Optional)

If your door is the 29" Super Wide Side-Swing Door,

go to steps 1–13 beginning on this page.

If your door is the 27" Wide Side-Swing Door, go to steps 1–11

beginning on page 16.

If your door is the 27" Wide Side-Swing Door with Glass, go to

steps 1–13 beginning on page 19.

NOTE: Magnetized screwdriver is helpful.

29" Super Wide Side-Swing Door

Place towel on top of dryer to avoid damaging the surface.

Place towel on dryer

1.

Remove bottom screws

2.

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from dryer

cabinet side of hinges.

Lift door until top screws in dryer cabinet are in large part of

hinge slot. Pull door forward off screws. Set door (handle side

up) on top of dryer. Remove top screws from dryer cabinet.

Lift door off top screws

3.

Remove screws from hinges

4.

Remove screws attaching hinges to door.

15

Remove screws at top, bottom, and side of door (4 screws)

that hold the inner and outer door together. Holding door over

towel on dryer, grasp sides of outer door and lift to separate it

from inner door. Set outer door aside.

NOTE: Do not pry apart with putty knife or screwdriver.

Do not pull on door seal or plastic door catches.

Remove screws from door

5.

Remove the door catch, bezel, and plug from the inside of

the inner door by squeezing and pulling/pushing them. Place

the door catch, bezel, and plug on the sides opposite from

where they were.

Plug

Catch and bezel

Switch door catch, bezel, & plug

6.

Rotate outer door

7.

Rotate outer door 180º and set it back down on inner door.

Reattach outer door panel to inner door panel so handle is

on the side where hinges were just removed. Insert 4 door

screws.

Flip door over

8.

Flip door over so handle side is down.

Attach door hinges

9.

Reattach door hinges to dryer door so that the larger hole is

at the bottom of the hinge.

16

Close door and check that door strike aligns with door

catch. If it is needed, slide door catch left or right within slot

to adjust alignment.

Check door strike alignment

13.

Insert screws in hinge holes on

dryer cabinet

12.

NOTE: Two people may be needed to reinstall door.

Insert screws into the bottom holes on left side of dryer

cabinet. Tighten screws halfway. Position door so large

end of door hinge slot is over screws. Slide door up so

screws are in bottom of slots. Tighten screws. Insert and

tighten top screws in hinges.

27" Wide Model Side-Swing Door

Place towel on dryer

1.

Place towel on top of dryer to avoid damaging the surface.

Use a small, at-blade screwdriver to gently remove 4 hinge

hole plugs on left side of dryer cabinet. Transfer plugs into

hinge holes on opposite side of dryer cabinet.

Remove and transfer

hinge hole plugs

11.

Remove door strike and door strike plug from dryer cabinet.

Insert the door strike into door strike plug hole and secure

with screw. Insert door strike plug into original door strike

hole and secure with screw.

10. Remove door strike and

door strike plug

Door strike plugDoor strike

17

Lift door until top screws in dryer cabinet are in large part of

hinge slot. Pull door forward off screws. Set door (handle side

up) on top of dryer. Remove top screws from dryer cabinet.

Lift door off top screws

3.

Remove bottom screws

2.

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from dryer

cabinet side of hinges.

Remove screws attaching hinges to door.

Remove screws from hinges

4.

Rotate outer door

6.

Rotate outer door 180º and set it back down on inner door.

Be certain to keep cardboard spacer centered between doors.

Reattach outer door panel to inner door panel so handle is on

the side where hinges were just removed. Insert 6 door screws.

Remove screws at top, bottom, and side of door (6 screws).

Keep door screws separate from hinge screws as they are

different sizes. Holding door over towel on dryer, grasp sides

of outer door and lift to separate it from inner door.

NOTE: Do not pry apart with putty knife or screwdriver.

Do not pull on door seal or plastic door catches.

Remove screws from door

5.

Flip door over

7.

Flip door over so handle side is down.

18

Check door strike alignment

11.

Close door and check that door strike aligns with door catch.

If it is needed, slide door catch left or right within slot to

adjust alignment.

Insert screws in hinge holes on

dryer cabinet

10.

NOTE: 2 people may be needed to reinstall door.

Insert screws into the bottom holes on left side of dryer cabinet.

Tighten screws halfway. Position door so large end of door hinge

slot is over screws. Slide door up so screws are in bottom of

slots. Tighten screws. Insert and tighten top screws in hinges.

Attach door hinges

8.

Reattach door hinges to dryer door so that the larger hole is

at the bottom of the hinge.

Remove and transfer plugs

9.

Remove the 4 screws that attach 2 plugs on the left side.

Transfer plugs to opposite side using the same 4 screws.

19

27" Wide Model Side-Swing Door with Glass

Place towel on dryer

1.

Place towel on top of dryer to avoid damaging the surface.

Remove bottom screws

2.

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from dryer

cabinet side of hinges.

Lift door until top screws in dryer cabinet are in large part of

hinge slot. Pull door forward off screws. Set door (handle side

up) on top of dryer. Remove top screws from dryer cabinet.

Lift door off top screws

3.

Remove screws attaching hinges to door.

Remove screws from hinges

4.

Flip door over

5.

Flip door over so handle side is down.

20

Rotate outer door

8.

Rotate outer door 180º and set it back down on inner door.

Be certain to keep cardboard spacer centered between

doors. Reattach outer door panel to inner door panel so

handle is on the side where hinges were just removed. Insert

4 door screws.

Remove screws at top, bottom, and side of door (4 screws).

Keep door screws separate from hinge screws as they are

different sizes.

Remove screws from door

6.

Attach door hinges

9.

Reattach door hinges to dryer door so that the larger hole is

at the bottom of the hinge.

Holding door over towel on dryer, pry inner door and lift to

separate it from outer door.

NOTE: Do not pull on door seal or plastic door catches.

Separate inner from outer door

7.

Remove door strike and door strike label from dryer cabinet.

Insert the door strike into hole where door strike label was

removed and secure with screw. Cover original door strike

hole with door strike label and press rmly into place.

Remove door strike and door

strike label

10.

Door strike labelDoor strike

21

Check door strike alignment

13.

Close door and check that door strike aligns with door catch.

If it is needed, slide door catch left or right within slot to

adjust alignment.

Troubleshooting

See the Use and Care Guide or visit our website and

reference “Frequently Asked Questions” to possibly avoid

the cost of a service call.

Insert screws in hinge holes on

dryer cabinet

12.

NOTE: 2 people may be needed to reinstall door.

Insert screws into the bottom holes on left side of dryer

cabinet. Tighten screws halfway. Position door so large end of

door hinge slot is over screws. Slide door up so screws are in

bottom of slots. Tighten screws. Insert and tighten top screws

in hinges.

Remove and transfer plugs

11.

Remove the 4 screws that attach 2 plugs on the left side.

Transfer plugs to opposite side using the same 4 screws.

Page is loading ...

W10514185A

W10514176A-SP

01/13

Printed in U.S.A.

Imprimé aux É.-U.

Used under license in Canada.

Emploi sous licence au Canada.

Whirlpool WGD4800XQ Installation guide

Whirlpool WGD4800XQ Installation guide

in other languages

Related papers

Other documents