Hitachi KM 12SC User manual

Brand: Hitachi

Model: KM 12SC

Category: Power tools

Type: User manual

This manual is also suitable for

1/2

3/8

1/4

3/8

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et

propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé

dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

M 12VC • M 12SC

KM 12VC • KM 12SC

Model Router

Modèle Toupie

Modelo Fresadora

M12VC

English

Page

IMPORTANT SAFETY INFORMATION ................ 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 4

GENERAL SAFETY RULES ................................... 4

SPECIFIC SAFETY RULES AND SYMBOLS ......... 5

USE OF EXTENSION CORD ................................. 7

FUNCTIONAL DESCRIPTION .................................... 8

NAME OF PARTS .................................................. 8

SPECIFICATIONS .................................................. 8

Page

ASSEMBLY AND OPERATION ................................. 9

APPLICATIONS ..................................................... 9

PRIOR TO OPERATION ......................................... 9

INSTALLING AND REMOVING BITS ................. 10

INSTALLING THE MOTOR HOUSING ............... 11

HOW TO USE THE ROOTER............................... 11

MAINTENANCE AND INSPECTION ....................... 15

ACCESSORIES ......................................................... 17

STANDARD ACCESSORIES ............................... 17

OPTIONAL ACCESSORIES ................................. 18

PARTS LIST .............................................................. 53

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES

DE SÉCURITÉ ............................................... 19

SIGNIFICATION DES MOTS

D’AVERTISSEMENT .................................... 19

SECURITE ................................................................ 20

REGLES GENERALE DE SECURITE

...................... 20

REGLES DE SECURITE SPECIFIQUES

ET SYMBOLES ............................................. 22

UTILISATION D’UN CORDON DE RALLONGE ...

DESCRIPTION FONCTIONNELLE ........................... 25

NOM DES PARTIES ............................................ 25

SPECIFICATIONS ................................................ 25

Page

ASSEMBLAGE ET FONCTIONNEMENT ................ 26

APPLICATIONS ................................................... 26

AVANT L’UTILISATION ...................................... 26

INSTALLATION ET RETRAIT DE LA MECHE ..... 27

INSTALLATION DU CARTER MOTEUR ............. 28

UTILISATION DE LA TOUPIE ............................. 28

ENTRETIEN ET INSPECTION .................................. 32

ACCESSOIRES ......................................................... 34

ACCESSOIRES STANDARD ............................... 34

ACCESSOIRES SUR OPTION ............................. 35

LISTE DES PIÈCES ................................................... 53

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE

SOBRE SEGURIDAD .................................... 36

SIGNIFICADO DE LAS PALABRAS

DE SEÑALIZACIÓN ...................................... 36

SEGURIDAD ............................................................. 37

NORMAS GENERALES DE SEGURIDAD........... 37

NORMAS Y SÍMBOLOS

ESPECÍFICOS DE SEGURIDAD ................... 39

UTILIZACIÓN DE UN CABLE PROLONGADOR ...

DESCRIPCIÓN FUNCIONAL .................................... 42

NOMENCLATURA ............................................... 42

SPECIFICATIONS ................................................ 42

Página

MONTAJE Y OPERACIÓN ...................................... 43

APLICACIONES ................................................... 43

ANTES DE LA OPERACIÓN ................................ 43

INSTALACIÓN Y EXTRACCIÓN DE

LAS BROCAS ............................................... 44

INSTALACIÓN DE LA CARCASA

DEL MOTOR ................................................. 45

CÓMO USAR LA FRESADORA .......................... 45

MANTENIMIENTO E INSPECCIÓN ........................ 49

ACCESORIOS ........................................................... 51

ACCESORIOS ESTÁNDAR ................................. 51

ACCESORIOS OPCIONALES .............................. 52

LISTA DE PIEZAS .................................................... 53

CONTENTS

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adaptor plugs. Check with a qualified

electrician if you are in doubt as to whether the outlet is properly grounded. If the

tools should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

(3) Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from

a receptacle. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord marked “W-

A” or “W”. These cords are rated for outdoor use and reduce the risk of electric

shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tires or under the influence of drugs, alcohol,

or medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools

with your finger on the switch or plugging in tools that have the switch on invites

accidents.

English

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures reduce

the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool's operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

(8) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

with another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal parts of the tool “live” and shock

the operator.

2. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

English

3. Handle the bits very carefully.

4. Check the bit carefully for cracks or damage before operation. Replace cracked or

damaged bit immediately.

5. Avoid cutting nails. Inspect for and remove all nails from the workpiece before

operation.

6. Hold the tool firmly with both hands.

7. Keep hands away from rotating parts.

8. Make sure the bit is not contacting the workpiece before the switch is turned on.

9. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration

or wobbling that could indicate improperly installed bit.

10. Be careful of the bit rotating direction and the feed direction.

11. Do not leave the tool running. Operate the tool only when hand-held.

12. Always switch off and wait for the bit to come to a complete stop before removing the

tool from workpiece.

13. Do not touch the bit immediately after operation: it may be extremely hot and could

burn your skin.

14. Always lead the power supply cord away from the tool towards the rear.

15. Never run the motor unit when it is not inserted in one of the router bases.

The motor is not designed to be handheld.

16. After changing the bits or making any adjustments, make sure the collet nut and any

other adjustment devices are securely tightened.

Loose adjustment device can unexpectedly shift, causing loss of control, loose rotating

components will be violently thrown.

17. Definitions for symbols used on this tool

V ............ volts

Hz .......... hertz

A ............ amperes

no .......... no load speed

---/min ... revolutions per minute

........... alternating or direct current

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

䢇 lead from lead-based paint.

䢇 crystalline silica from bricks and cement and other masonry products.

䢇 arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

English

USE OF EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure

to use one heavy enough to carry the current your product will draw.

An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. Table shows the correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the

heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25 26 – 50 51 – 100 101 – 150

(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)

Ampere Rating AWG

More Not More

Than Than

0 – 618161614

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or

frayed electrical cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in

any environment where electric shock is possible.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

English

1/2

3/8

1/4

5/8

3/4

7/8

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool.

NAME OF PARTS

Fig. 1

SPECIFICATIONS

Model M12VC M12SC

Motor Single Phase, Series Commutator Motor

Power source Single Phase 120V AC 60 Hz

Collet chuck capacity 1/2” (12.7 mm), 1/4” (6.35 mm)

Current 11 A

No-load speed 8000/min – 24000/min 24000/min

Weight (with cord) 7.3 lbs (3.3 kg)

Dial

Sub Base

Lever

Motor Housing

Scale Ring

Brush Cap

Collet Chuck

Switch

Handle

Base

English

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Woodworking jobs centered on grooving and beveling.

For example, grooving beveling, cutting, copying, engraving, shape cutting,

combinations and others.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle

while the switch is in the ON position, the power tool will start operating immediately

and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as short as

practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Confirming condition of the environment

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

English

INSTALLING AND REMOVING BITS

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle to avoid serious trouble.

1. Installing bits

(1) Remove the motor housing from base as

follows.

(a) Open the lever. (Fig. 2)

(b) While holding the base, turn the motor

housing counterclockwise.

disengaged from the groove in the

motor housing. Lift the motor housing

free from the base.

(2) Clean and insert shank of bit into the collet

chunk until shank bottoms, then back it out

approximately 1/16” (approx. 2 mm).

(3) With the bit inserted and 16 mm wrench

holding the armature shaft, use the 23 mm

wrench to firmly tighten the collet chuck in

a clockwise direction (viewed from under

the router). (Fig. 3)

(4) When using the 1/4” diameter shank bit,

replace the equipped collet chuck with the

one for 1/4” diameter shank bit which is

provided as the standard accessory.

CAUTION:

䢇 Ensure that the collet chuck is firmly

tightened after inserting a bit. Failure to do

so will result in damage to the collet chuck.

2. Removing bits

When removing the bits, do so by following

the steps for installing bits in reverse order.

Motor

Housing

Base

Lever

Fig. 2

23mm

Wrench

Bit

Collet

Chuck

16mm

Wrench

Fig. 3

Loosen

Tighten

English

INSTALLING THE MOTOR HOUSING

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle to avoid serious trouble.

1. Installing the motor housing

(1) Open the lever.

(2) While holding the base, insert the motor

housing into the base aligning the pin with

the groove in the base.

(3) Confirm that the pin and the groove are

aligning. Rotate the motor housing

clockwise into the base.

(4) Close the lock lever.

CAUTION:

You should be able to clamp the locking lever without excessive force. Excessive force

may damage the base. You should not be able to move the motor in the base when

the lever is clamped. To adjust the lever’s clamping force, open the locking lever and

turn the knob nut in small increments. Turning the knob nut clockwise tightens the

lever, while turning the knob nut counterclockwise loosens the lever.

HOW TO USE THE ROUTER

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle to avoid serious trouble.

1. Adjusting depth of cut

(1) Place the tool on a flat wood surface.

(2) Open the lever and turn the motor housing

until the bit just touches the flat surface. (Fig. 5)

(3) Clamp the lever down until the point where

a click can be felt. (Fig. 6)

NOTE:

The motor housing can be temporarily

secured by clamping the lever (the motor

housing does not slide down by its own

weight).

If the motor housing slides down, make

adjustments by tightening the knob nut.

Turning the knob nut clockwise tightens the

lever, while turning the knob nut

counterclockwise loosens the lever.

Motor

Housing

Groove

Knob Nut

Base

Lever

Fig. 4

Motor

Housing

Index Line

Graduation

Scale Ring

Base

Lever

Fig. 5

Knob Nut

Lever

Fig. 6

English

(4) While holding up the base slightly, turn the

motor housing clockwise until the index line

on the motor housing reaches the desired

depth indicated on the scale ring. (Fig. 5)

(5) Close the lever firmly.

2. Adjusting the rotation speed (Model

M12VC only)

The M12VC have an electronic control

system that allows stepless rpm changes.

As shown in Fig. 7 dial position “1” is for

minimum speed and position “6” for

maximum speed.

3. Centering the template guide adapter

WARNING: Be sure to switch power

OFF and disconnect the

plug from the receptacle to

avoid serious trouble.

(1) Loosen the 2 template guide adapter screws,

so that the template guide adapter can be

moved. (Fig. 8)

(2) Insert the centering gauge through the hole

in the template guide adapter and into the

collet chuck. (Fig. 9)

(3) Tighten the collet chuck by hand.

(4) Tighten the lever. (This aligns the center of

the template guide adapter.)

(5) Tighten the template guide adapter screws,

and pull out the centering gauge.

4. Guiding the router

(1) Template guide (M12VC, M12SC: Optional

accessory)

Use the template guide when employing a

template for producing a large quantitiy of

identically shaped products. (Fig. 10)

As shown in Fig. 11, to install insert template

guide in center hole in template guide

adapter and secure in place with the lock

nut.

A template is a profiling mold made of

plywood or thin lumber. When making a

template, pay particular attention to the

matters cescribed blow and illustrated in

Fig. 12.

Fig. 7

Dial

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Template

Guide Adapter

Screw

Centering

Gauge

Screw

Collet

Chuck

Lever

Lock Nut

Template

Guide

Template

Guide Adapter

Template

Guide Adapter

Template

English

When using the router along the interior

plane of the template, the dimensions of the

finished product will be less than the

dimensions of the template by an amount

equal to dimension “A”, the difference

between the radius of the template guide

and the radius of the bit. The reverse is frue

when using the router along the exterior of

the template.

Secure the template to the workpiece. Feed

the router in the manner that the template

guide moves along the template as shown

in Fig. 12.

(2) Straight guide (optional accessory)

Use straight guide for chamfering and

groove cutting along the materials side.

1 Insert the guide bar into the hole in the bar

holder, then lightly tighten the 2 wing bolts

(A) on top of the bar holder.

2 Insert the guide bar into the hole in the base,

then firmly tighten the 2 hex socket bolts

(standard accessories).

3 Make minute adjustments of the dimensions

between the bit and the guide surface with

the feed screw, then firmly tighten the 2

wing bolts (A) on top of the bar holder and

the wing bolt (B) that secures the straight

guide. (Fig.13)

4 As shown in Fig. 14, securely attach the

bottom of the base to processed surface of

the materials. Feed the router while keeping

the guide plane on the surface of the

materials.

5. Cutting

WARNING:

䢇 Wear eye protection when operating this tool.

䢇 Keep your hands, face and other body parts away from the bits and any other rotating

parts, while operating the tool.

(1) The bit must be kept clear of the materials

which are to be cut, when the power is being

turned on. (Fig. 15)

(2) Then turn the tool on and wait until the bit

attains full speed.

Guide Bar

Feed Screw

Hex

Socket

Bolt

Guide

Plane

Straight

Guide

Bar

Holder

Wing

Bolt (A)

Wing

Bolt (B)

Fig. 13

Fig. 14

Template Guide

Template

Fig. 12

Separate

Fig. 15

English

(3) The bit rotates clockwise (arrow direction

indicated on the base). To obtain maximum

conformance with the feed directions shown

in Fig. 16.

NOTE:

䢇 Moving the tool forward fast may cause a poor quality of cut, or damage to the bit or

motor. Moving the tool forward too slowly may burn and mar the cut.

The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut.

Before beginning the cut on the actual workpiece, it is advisable to make a sample cut

on a piece of scrap lumber. This will show exactly how the cut will look as well as

enable you to check dimensions.

䢇 Abnormalities and overloads will trigger the overload protector, and stop operation.

Remove the load immediately, and turn the power off, then on. The rotation speed

should return to normal.

䢇 Do not use a power generator as the power source. It may cause the rotation speed to

fluctuate.

䢇 When using the straight guide, be sure to install it on the right side in the feed direction.

This will help to keep it flush with the side of the workpiece.

Fig. 16

Router feed

Rotation of bit

Router feed

workpiece

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the screws

Regularly inspect all screws and ensure that they are fully tightened. Should any of the

screws be loosened, retighten them immediately.

WARNING: Using this router with loosened screws is extremely dangerous.

2. Inspecting the carbon brushes (Fig. 17)

The motor employs carbon brushes which

are consumable parts. Replace the carbon

brush with a new one when it becomes worn

to its wear limit. Always keep carbon

brushes clean and ensure that they slide

freely within the brush holders.

CAUTION: Using this router with a carbon brush which is worn in excess of the wear

limit will damage the motor.

NOTE: Use HITACHI carbon brush No. 43 indicated in Fig. 17.

3. Replacing carbon brushes

Remove the brush caps with a slotted

screwdriver. The carbon brushes can then

be easily removed. (Fig. 18)

4. Service and repairs

All quality power tools will eventually

require servicing or replacement of parts

because of wear from normal use. To assure

that only authorized replacement parts will

be used, all service and repairs must be

performed by a HITACHI AUTHORIZED

SERVICE CENTER, ONLY.

5. Service parts list

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried

out by a Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service

Center when requesting repair or other maintenance. In the operation and maintenance

of power tools, the safety regulations and standards prescribed in each country must

be observed.

Wear limit

No. of carbon

Fig. 17

Fig. 18

Slotted-head

Screwdriver

Brush Cap

English

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried

out by an Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi

Authorized Service Center when requesting repair or other maintenance. In

the operation and maintenance of power tools, the safety regulations and

standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the

latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without

prior notice.

English

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are

not intended for use with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement part or accessory

with your tool. The use of any other attachment or accessory can be

dangerous and could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

1. Model M12VC, M12SC

(1) 1/4” Collet Chuck (Code No. 323-293)

(2) Template Guide Adapter (attaches

to the router) (Code No. 323-272)

(3) Centering Gauge (Code No. 323-296)

(4) 16 mm Wrench (Code No. 323-294)

(5) 23 mm Wrench (Code No. 323-295)

2. Model KM12VC, KM12SC

(1) 1/4” Collet Chuck (Code No. 323-293)

(2) Template Guide Adapter (attaches to

the router) (Code No. 323-272)

(3) Centering Gauge (Code No. 323-296)

(4) 16 mm Wrench (Code No. 323-294)

(5) 23 mm Wrench (Code No. 323-295)

(6) Large Hole Sub Base (Code No. 323-297)

(7) Template Guide (Fig. 19)

(8) Lock Nut (Code No. 323-305)

(9) Chip Cover (Code No. 323-292)

(10)Case (Code No. 323-358)

Code

ABC

No.

323-298

1/4” 5/16” 5/32”

(6.5 mm) (8 mm) (4 mm)

323-299

9/32” 3/8” 5/16”

(7 mm) (9.5 mm) (8 mm)

323-300

11/32” 7/16” 5/32”

(8.7 mm) (11.1 mm) (4 mm)

323-301

13/32” 1/2” 5/16”

(10.3 mm) (12.7 mm) (8 mm)

323-302

17/32” 5/8” 9/16”

(13.5 mm) (16 mm) (14.3 mm)

323-303

21/32” 3/4” 9/16”

(16.6 mm) (19.1 mm) (14.3 mm)

323-304

5/8” 51/64” 9/16”

(16 mm) (20.2 mm) (14.3 mm)

Fig. 19

English

OPTIONAL ACCESSORIES …………… sold separately

(1) Straight Guide Set (Code No. 323-342)

1Bar Holder (Code No. 323-343)

2Feed Screw (Code No. 956-793)

3Wing Bolt (Code No. 301-806)

4Guide Bar (Code No. 323-345)

5Straight Guide (Code No. 323-344)

(2) Dust Collector Set (Code No. 323-346)

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

Page is loading ...

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known [to the State of California] to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

AVERTISSEMENT:

La poussière résultant d'un ponçage, d'un sciage, d'un meulage, d'un perçage ou de

toute autre activité de construction renferme des produits chimiques qui sont connus

[par l'Etat de Californie] pour causer des cancers, des défauts de naissance et autres

anomalies de reproduction. Nous énumérons ci-dessus certains de ces produits

chimiques:

● Plomb des peintres à base de plomb,

● Silice cristalline des briques et du ciment et autres matériaux de maçonnerie, et

● Arsenic et chrome du bois d'oeuvre traité chimiquement.

Le risque d'exposition à ces substances varie en fonction de la fréquence d'exécution de

ce genre de travail. Pour réduire l'exposition à ces produits chimiques, travailler dans un

lieu bien ventilé, et porter un équipement de protection agréé, par exemple un masque

anti-poussière spécialement conçu pour filter les particules microscopiques.

ADVERTENCIA:

Alogunos polvos creados por el lijado mecámico, el aserrado, el esmerilado, el taladrado

y otras actividades de construcción contienen sustancias químicas conocidas [por le

Estado de California] como agentes cancerígenos, defectos congénitos y otros daños

reproductores. Algunos ejemplos de estas sustancias químicas son:

● El plomo de las pinturas a base de plomo,

● El sílice cristalino de los ladrillos y cemento y otros productos de mampostería, y

● El arsénico y el cromo de la madera tratada químicamente.

El riesgo resultante de la exposición varía según la frecuencia con que se realiza este tipo

de trabajo. Para reducir la exposicíon a esta sustancias químicas: trabaje en un lugar bien

ventilado y realice el trabajo utilizando el equipamiento apropiado, tal como las máscares

para el polvo especialmente diseñados para eliminar las partículas minúsculas.

Issued by

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

Hitachi Koki U.S.A., Ltd.

3950 Steve Reynolds Blvd.

Norcross, GA 30093

Hitachi Koki Canada Co.

6395 Kestrel Road

Mississauga ON L5T 1Z5

405

Code No. C99133061

Printed in China

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil peut entraîner la mort ou

de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre de mode d'emploi AVANT d’utiliser l’outil.

Garder ce mode d'emploi à la disponibilité des autres utilisateurs et propriétaires avant

qu’ils utilisent l’outil. Ce mode d’emploi doit être conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the tool. Please keep this manual available

for other users and owners before they use the tool. This manual should be stored in

safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en la muerte o lesiones corporales de gravedad!

Este manual contiene información importante sobre la seguridad del producto. Por

favor lea y comprenda este manual ANTES de operar la herramienta. Asimismo, deje

este manual a disposición de otras personas y propietarios para que puedan leerlo

antes de usar la herramienta. Este manual debe ser guardado en un lugar seguro.

Plunge Base

Socle d’inclinaison

Base de penetración

001CoverF_PlungeBase_US 9/5/07, 20:101

Page is loading ...

Hitachi KM 12SC User manual

Brand: Hitachi

Model: KM 12SC

Category: Power tools

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Hitachi KM 12SC Manuel utilisateur
español: Hitachi KM 12SC Manual de usuario

Hitachi KM 12SC User manual

This manual is also suitable for

Hitachi KM 12SC User manual

in other languages

Related papers

Other documents