Electro-Voice CPS2.12 User manual

Brand: Electro-Voice

Model: CPS2.12

Category: Supplementary music equipment

Type: User manual

Page is loading ...

CONTRACTOR PRECISION SERIES

CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Scope of Delivery and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Features and Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Responsibility of the User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Controls, Indicators and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mains Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Groundlift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

High Pass Filter (HPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power on delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Selecting the Mode Of Operation and Audio Output Cabeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Audio Input Cabeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Standby Mode (POWER REMOTE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Fan Cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

RCM-810. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

INHALT

Einführung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Willkommen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Auspacken und Inspektion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Lieferumfang und Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Eigenschaften & Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Verantwortung des Betreibers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Bedienelemente, Anzeigen und Anschlüsse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Betriebsspannung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Netzschalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Einbau . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Kühlung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Groundlift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Hochpassfilter (HPF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Einschaltverzögerung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Betriebsart (MODE) und Verkabelung des Audio-Ausgangs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Verkabelung des Audio-Eingangs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Betrieb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Eingangspegel-Regler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Anzeigen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Standby-Modus (POWER REMOTE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Lüfter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Optionen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

RCM-810. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Specifications/Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Mains Operation & Resulting Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Block Diagram / Blockschaltbild . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Dimensions / Abmessungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

4 Owner‘s Manual

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not cover any ventilation openings. Install in accordance with the manufacture’s instructions.

8. Do not install near heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or the grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. I the

provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for a long period of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or orbjects have fallen into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

15. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the

equipment.

16. To completely disconnect this equipment from the AC Mains, disconnect the power supply cord plug from the AC receptacle.

17. The mains plug of the power supply cord shall remain readily operable.

IMPORTANT SERVICE INSTRUCTIONS

CAUTION: These servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not

perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so.

Refer all servicing to qualified service personnel.

1. Security regulations as stated in the EN 60065 (VDE 0860 / IEC 65) and the CSA E65 - 94 have to be obeyed when servicing the appliance.

2. Use of a mains separator transformer is mandatory during maintenance while the appliance is opened, needs to be operated and is

connected to the mains.

3. Switch off the power before retrofitting any extensions, changing the mains voltage or the output voltage.

4. The minimum distance between parts carrying mains voltage and any accessible metal piece (metal enclosure), respectively between the

mains poles has to be 3 mm and needs to be minded at all times. The minimum distance between parts carrying mains voltage and any

switches or breakers that are not connected to the mains (secondary parts) has to be 6 mm and needs to be minded at all times.

5. Replacing special components that are marked in the circuit diagram using the security symbol (Note) is only permissible when using

original parts.

6. Altering the circuitry without prior consent or advice is not legitimate.

7. Any work security regulations that are applicable at the locations where the appliance is being serviced have to be strictly obeyed. This

applies also to any regulations about the work place itself.

All instructions concerning the handling of MOS-circuits have to be observed

WEEE RECYCLING/DISPOSAL INSTRUCTIONS

The lightning flash with arrowhead symbol, within an

equilateral triangle is intended to alert the user to the

presence of uninsulated „dangerous voltage“ within the

product’s enclosure that may be of sufficent magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintance (servicing) instructions in the

literature accompanying the appliance.

NOTE: SAFETY COMPONENT (MUST BE REPLACED BY ORIGINAL PART)

The Wheelie Bin symbol found on the product or in the manual indicates that this product must not be dis-

posed of with other waste. It is in our category the manufacturer’s responsibility to properly dispose of their

waste electrical and electronic equipment (WEEE) at the end of its life. Due to the differences in each EU

country’s management of WEEE, please contact your local distributor. We are committed to facilitate our own

electronic-waste-management-system, for the free of charge return of all EVI Audio GmbH products: Telex,

Dynacord, ElectroVoice, Midas Consoles, KlarkTeknik and RTS. Arrangements are made with the dealer

where you purchased the equipment from, for the returning of all unusable equipment at no cost, to the fac-

tory in Straubing, for environmental protective disposal.

CONTRACTOR PRECISION SERIES

Owner‘s Manual 5

1 Introduction

1.1 Welcome

Thank you for choosing an Electro-Voice CPS series amplifier. Please take time to consult this manual so that you can

understand all the features built into your Electro-Voice amplifier and fully utilize all its performance capabilities.

1.2 Unpacking and Inspection

Carefully open the packaging and take out the power amplifier. Inspect the power amp’s enclosure for damages that might

have happened during transportation. Each amplifier is examined and tested in detail before leaving the manufacturing site to

ensure that it arrives in perfect condition at your place. Please inform the transport company immediately, if the power

amplifier shows any damage. Being the addressee, you are the only person who can claim damages in transit. Keep the

cardboard box and all packaging materials for inspection by the transport company.

Keeping the cardboard box including all packing materials is also recommended, if the power amplifier shows no external

damages.

When shipping the power amp, make sure to always use its original box and packaging materials. Packing

the power amplifier like it was packed by the manufacturer guarantees optimum protection from transport damage.

1.3 Scope of Delivery and Warranty

• 1 Power Amplifier

• 1 Owner‘s Manual (this document)

• 1 Mains Cord

• 1 Output connector, 4 pole

• 2 Input connector, 3 pole

• 1 Power Remote connector, 2 pole

• 1 Warranty Certificate

Keep the original invoice that states the purchase/delivery date together with the warranty certificate at a safe place.

1.4 Features and Description

Electro-Voice CONTRACTOR PRECISION SERIES Series amplifiers offer a package of reliable high output power, high

efficiency and legendary pro audio performance. They are the premium choice as system drive for a variety of Electro-Voice‘s

installation loudspeakers like e.g. EVI, FRi, FRX or Variplex families. Their comprehensive protection system includes circuitry

against overheating, overload, short circuit, HF and DC as well as back-EMF and inrush current. Loudspeakers are protected

by turn-on-delay relays.

1.5 Responsibility of the User

Speaker System Damage

CPS power amps provide extremely high power output that might be dangerous for human beings as well as for the

connected speaker systems. High output voltages can damage or even destroy the connected speaker systems, especially,

when the CPS amplifier is operated in bridged mode. Prior to connecting any loudspeakers, make sure to check the speaker

system’s specifications for continuous and peak power handling capacities. Even if amplification has been reduced through

lowering the input level controls on the amplifier’s front panel, it is still possible to achieve full power output with a sufficiently

high input signal.

Danger at the Loudspeaker/Power Outputs

CPS amplifiers are capable of producing dangerously high voltage output that is present at the output connectors. To protect

yourself from electric shock, do not touch any blank speaker cables during operation of the power amp.

CAUTION:

Do not ship the power amp in any other but its original packaging.

CONTRACTOR PRECISION SERIES

6 Owner‘s Manual

HF-Interference (FCC Information USA)

1. IMPORTANT: Do not modify this unit! Changes or modifications not expressly approved by the manufacturer could void the

user‘s authority, granted by the FCC, to operate the equipment.

2. NOTE:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection agains harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

This Class A digital apparatus complies with Canadian ICES-003.

Cat appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

WARNING:

The terminals marked with are hazardous live and the external wiring connected to these

terminals requires installation by an instructed person or the use of ready-made leads of

cords.

This is a Class A product. In a domestic environment this product may cause radio inter-

ferences in which case the user may be required to take adequate measures.

CONTRACTOR PRECISION SERIES

Owner‘s Manual 7

2 Installation

2.1 Controls, Indicators and Connections

Front View

Rear View

1 Level Indicators for channels 1 and 2

2 Protections Indicator (PROTECT)

3 Muting Indicator (MUTE) for channels 1 and 2

4 Power On/Off Indicator (POWER)

5 Standby Indicator (STANDBY)

6 Remote Amplifier Indicator (IRIS-Net)

7 Mains Switch

1 Mains Input

Ground Lift Switch (CIRCUIT

⊥ TO CHASSIS SWITCH)

3 POWER REMOTE connector

4 Power On Delay selection switch (ON DELAY)

5 Expansion Slot

6 Audio Inputs (INPUT) for channels 1 and 2

7 Input Level Control (LEVEL) for channels 1 and 2

8 Power Amp Mode Switch (MODE)

9 Highpass Filter Switch (HPF)

10 Type Plate

11 Power Amp Outputs (CH 1, CH 2, BRIDGED)

CONTRACTOR PRECISION SERIES

8 Owner‘s Manual

2.2 Operating Voltage

The power amplifier receives its power supply via the MAINS IN connector. Only the provided power cord may be used.

During installation, always separate the power amplifier from the mains. Connect the power amplifier only to a mains network,

which corresponds to the requirements indicated on the type plate.

Mains Operation & Resulting Temperature

The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into

heat. The difference between power consumption and dispensed power is called power dissipation (P

). The amount of heat

resulting from power dissipation might remain inside of a rack-shelf and needs to be diverted using appropriate measures.

The tables on page 31 allow the determination of power supply and cabling requirements. The tables are meant as auxiliary

means for calculating temperatures inside of a rack-shelf system/cabinet and the ventilation efforts necessary.

The column P

lists the leakage power in relation to different operational states. The column BTU/hr lists the dispensed heat

amount per hour. Power consumption is direct proportional for other mains voltages. The following conversion factors are

meant for easy conversion: 100V = 2.3; 120V = 1.9; 240V = 0.96

2.3 Mains Switch

The Mains Switch on the front panel separates the power amp from the mains. Turning the

Mains Switch to ON starts booting up the power amp. A soft start circuit compensates

mains inrush current peaks and thus prevents triggering AC mains fuse when switching on

the amplifier. Speaker system switch-on is delayed by approximately 2 seconds via output

relays, effectively suppressing any possible power-on noise, which otherwise might be

heard through the loudspeakers. PROTECT-LED light and fans are at high speed during

this delay. This indicates all protections are working fine.

2.4 Mounting

CPS amplifiers have been designed for installation in a conventional 19-inch rack case. Attach the power amp with its frontal

rack mount ears using 4 screws and washers as shown in following illustration.

Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been

installed will be transported. Failure to do so may result in damage to the power amplifier as well as to the rack case. Attach

the power amp as shown in the illustration using 4 case nuts and screws. Brackets for securing the power amplifier are

available as accessories.

2.5 Ventilation

As with all Electro-Voice power amps with fan cooling, the airflow direction is front-

to-rear, obviously because there is more cold air outside of the rack case than

inside. The power amplifier remains cooler and dissipating the developing waste

heat in a specific direction gets easier. In general, setting up or mounting the

power amplifier has to be done in a way that fresh air can enter unhindered at the

front and exhausted air can exit at the rear. When installing the power amp in a

case or rack system, attention should be paid to these details to provide sufficient

ventilation. Allow for an air duct of at least 60 mm x 330 mm between the rear

panel of the power amplifier and the inner wall of the cabinet/rack case. Make

sure that the duct reaches up to the cabinet’s or the rack case’s top ventilation

louvers. Leave room of at least 100 mm above the cabinet/rack case for ventilation. Since temperatures inside of the cabinet/

rack case can easily rise up to 40 °C during operation of the power amp, it is mandatory to bear in mind the maximum

allowable ambient temperature for all other appliances installed in the same cabinet/rack case.

CONTRACTOR PRECISION SERIES

Owner‘s Manual 9

For fixed amplifier installations in a device control room that incorporate a central air-cooling system or air conditioners,

calculating the maximum heat emission may be necessary. Please also take notice of the information on page 31.

2.6 Groundlift

The ground lift switch allows eliminating noise loops. When operating the power amplifier together with other

equipment in a rack case, setting the switch to the GROUNDED position is recommended. Set the switch to

UNGROUNDED, when the power amplifier is operated together with appliances with differing ground

potentials.

2.7 High Pass Filter (HPF)

The Hi-Pass filter (50 Hz, 18 dB/oct) allows effective attenuation of low frequency audio signals, which could

cause saturation problems with connected output transformers. Set the switch to the 50Hz position for

activating the High Pass Filter. Set the switch to the OFF position if no attenuation of low frequency audio

signals is required.

2.8 Power on delay

The ON DELAY switch at the amplifier rear panel allows selecting the power on delay time.

Following table shows possible switch settings and corresponding delay times.

CAUTION:

Blocking/closing the power amp’s ventilation louvers is not permissible. Without sufficient

cooling/ventilation, the power amplifier may automatically enter protect mode. Keep ventilati-

on louvers free from dust to ensure unhindered airflow.

Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat

radiating devices.

To ensure trouble-free operation, make certain that the maximum allowable ambient tempera-

ture of +40°C is not exceeded.

ON DELAY Delay time

(in s)

ON DELAY Delay time

(in s)

0 0.52 8 1.05

1 0.59 9 1.15

2 0.63 A 1.25

3 0.69 B 1.40

4 0.75 C 1.49

5 0.84 D 1.55

6 0.90 E 1.61

7 0.95 F 1.69

CONTRACTOR PRECISION SERIES

10 Owner‘s Manual

2.9 Selecting the Mode Of Operation and Audio Output Cabeling

The MODE switch on the power amp‘s rear panel defines how the audio inputs handle the input signals. Possible settings are

DUAL, PARALLEL or BRIDGED.

DUAL

In DUAL mode, the two channels of the power amplifier work independent from each other. This mode

of operation is being used for all 2-channel applications, like stereo operation. Using the input level

controls on the power amp’s rear panel allows independently adjusting the channels’ amplification.

PARALLEL

In PARALLEL mode, the inputs of channel 1 and channel 2 are directly electrically linked. The audio

signal has to be applied to the input connectors of channel 1. Using the input level controls to

independently control the amplification of the two channels is still possible because only the channels’

inputs are linked. PARALLEL operation is the mode of choice, whenever the same input signal drives

multiple power amp channels of a large system installation.

See illustration right for connecting speakers in DUAL or PARALLEL

mode. The correct connection is also indicated at the amplifiers rear

panel.

BRIDGED

In BRIDGED mode both amp channels work in push-pull operation to provide doubled output voltage.

The audio signal has to be applied to the input connectors of channel 1, amplification is set via input

level control of channel 1 only.

Setting the MODE switch on the power amp‘s rear panel to BRIDGED lets the power

amplifier run in bridged mode operation and speaker connection has to be

established using pins 1+ und 2-, see illustration right. The correct connection is also

indicated at the amplifiers rear panel.

CAUTION:

In PARALLEL mode, the input signal has to be fed to input channel 1 only.

CAUTION:

In BRIDGED mode, the input signal has to be fed to input channel 1 only. Amplification is set

via input level control of channel 1 only.

In BRIDGED mode operation, it is not allowable for the load connected to fall below a value of

4 ohms. Extremely high voltages can be present at the output. The connected speaker sy-

stems must be able to handle such voltages. Make sure to completely read and fully observe

power rating specifications of the speaker systems to be used and to check them against the

output power capacity of the power amp.

CONTRACTOR PRECISION SERIES

Owner‘s Manual 11

2.10 Audio Input Cabeling

Inputs are electronically balanced. Whenever possible, using balanced audio signal feeds at the input of the power

amplifier is always preferred. Unbalanced connections should only be used if the cables are very short and no

interfering signals are to be expected in the vicinity of the power amplifier. In this case, bridging the screen

(shielding) and the pin of the inverting input inside of the connector is mandatory. Otherwise, a 6 dB drop in level

could result. Please also see following illustration. Due to their immunity against external interference sources,

such as dimmers, mains connections, HF-control lines, etc., using balanced cabling and connections is always

preferable.

Illustration 2.1: Balanced / unbalanced connection of input

CONTRACTOR PRECISION SERIES

12 Owner‘s Manual

3 Operation

3.1 Volume Control

In DUAL and PARALLEL mode, the level controls LEVEL on the power amp’s rear panel are used to control

the amplification of the corresponding channel. Turning the control to the right increases and turning it to the

left decreases the volume. In BRIDGED mode operation, the output volume of the power amp is only

controlled by the CH 1 level control. Any changes in the setting of the CH 2 level control are ignored.

3.2 Indications

PROTECT

The PROTECT LED lights indicating that one of the internal protection circuits against thermal overload,

short-circuit, Back-EMF, HF-occurrence at the output, etc., has been activated. In that case, the output

relays separate the power amps from the load connected to prevent the connected loudspeaker systems

and the power amplifiers as well from being damaged. Whatever caused the fault – e.g. a short-circuited

speaker cable – needs to be remedied. In case of thermal overload you have to wait until the power

amplifier automatically regains normal operation.

MUTE

The MUTE LED lights red whenever the power amp’s output signal is being muted, which happens when

manually muting the output signal via IRIS-Net™.

-30dB...LIMIT

Level indication is realized via vertical LED chains on the power amp’s front panel that individually indicate

the actual levels of each channel at -30dB, -10dB and -3dB below full modulation. The LIMIT LED lights as

soon as the integrated dynamic audio limiter is activated and the power amplifier is driven at the clipping

limit or generally at its maximum capacity. Short-term blinking is not a problem, because the internal limiter

controls input levels of up to +21 dBu down to a THD of approximately 1 %. If, on the other hand, the LIMIT

LED light constantly, reducing the volume is recommended to prevent the loudspeaker systems connected

from being damaged by probable overload.

POWER

The POWER LED lights green when the power amplifier is on. If the POWER-LED does not light, despite

the fact that the amplifier has been switched on, this indicates that the power amp is not connected to the

mains or the primary fuse has blown.

STANDBY

The STANDBY-LED lights yellow when the power amp is in standby mode. Standby mode reduces the

amp’s power consumption to an absolute minimum. Activating the standby mode is possible via IRISNet™

or the POWER REMOTE port at the amp‘s rear panel.

IRIS-Net

The IRIS-Net-LED lights blue if an IRIS-Net™-compatible remote control module has been installed in the

power amp’s extension slot and successful data communication has been established. The IRIS-Net LED

blink slowly whenever the “Find” function in IRIS-Net™ is being used to locate a power amplifier in the rack.

CONTRACTOR PRECISION SERIES

Owner‘s Manual 13

3.3 Standby Mode (POWER REMOTE)

POWER REMOTE provides a simple way to remotely power-on/off the power amplifier. The POWER

REMOTE function is only useful for appliances not employing a Remote Control Modul. Controlling CPS

amplifiers with Remote Control Module installed per POWER REMOTE is not recommended.

Leaving the pins of POWER REMOTE socket open the appliance power is switched on. When connecting

the pins the applicance enters standby mode.

3.4 Fan Cooling

The power amplifier has two fans. The fans are switched in three performance-optimized levels, i.e. they are not running

permanently but the speed of the fans is controlled depending on the temperature. That in return ensures very silent running

during idle state.

The temperatures of the power amps‘s channels are registered and monitored individually.

CONTRACTOR PRECISION SERIES

14 Owner‘s Manual

4 Options

Installing one of the optionally available extension modules in the extension slot on the rear panel lets you expand the power

amp’s functional range. As an example, the following paragraphs describe the RCM-810 Remote Control Module. Please

read and follow the instructions provided in the documentation that you have received together with each extension module.

4.1 RCM-810

System Description and Features

The RCM-810 Remote Control Module is a digital controller module for live sound reinforcement, PA and fixed installation

applications. Installing the RCM-810 turns a conventional amp into a remote amplifier, which, at any time, provides complete

overview of the overall system status and control of all system parameters.

RCM-810 modules allow the integration of amplifiers into a remote control network with up to 250 units. This offers the

possibility to control and monitor an entire PA system from one or more PCs using the IRIS-Net - Intelligent Remote &

Integrated Supervision - software package. All operational states, e.g. power-on status, temperature, activation of protections,

load impedance, etc., are centrally registered and displayed in IRIS-Net. This provides the possibility to react and to

selectively intervene even before critical operational states arise. Programming an automatic reaction, when specific

thresholds are being exceeded or fallen below, is also possible.

All parameters, like power on/off, muting, etc. can be

controlled in real-time and stored in the amplifier. In the

event of network failure or loss of power, all settings stay

intact, independent of the control by the network.

Furthermore, the RCM-810 provides a control port with

freely programmable control inputs and control outputs.

Control inputs (GPI's) allow the connection of switches.

IRIS-Net offers the possibility to program a variety of logic

functions for the inputs. Control outputs (GPO's) allow the

connection of external components, which, for example, are

used to signal specific states to peripheral equipment.

Consequently, an amplifier with a RCM-810 module

installed corresponds to highest safety requirements. For

further details about configuration, control and monitoring of

amps with installed RCM-810 modules, please refer to the

documentation of the IRIS-Net. The latest version of IRIS-Net is available at www.electrovoice.com.

Controls and Connections

1 ADDRESS Selector Switch

The two address selector switches are for setting the network address of the RCM-810. CAN networks

support addresses in the range of 01 to 250 (FA hex). Addressing has to be carried out in the hexadecimal

number system. The LOW selector switch sets the lower digit, while HIGH sets the higher digit.

Illustration 4.1: Controls and Connections of the RCM-810

CAUTION:

Each address may exist only once in a system. Otherwise, network conflicts may arise.

CONTRACTOR PRECISION SERIES

Owner‘s Manual 15

Address 0 (00 hex, delivery status) disables remote communication between the RCM-810 and the bus. The module does not

appear in the system, even though it is physically connected to the CAN-bus.

2 STATUS LED

The STATUS-LED is for monitoring the communication on the CAN bus. The LED blinks rhythmically every 3

seconds, when the module’s address is set to “00“, which means that it is disconnected from the CAN bus

and software control. The LED blinks rhythmically in intervals of one second, when an address in the range of

01 to 250 has been assigned to the module and there has not yet been any activity on the CAN bus. As soon

as communication on the CAN bus is recognized, the LED lights for at least 100 ms, when the power

amplifier sends data on the CAN bus.

3 REMOTE CAN BUS Connection

The RCM-810 module provides two RJ-45 sockets for connecting to the REMOTE CAN BUS. These sockets

are connected in parallel and serve as inputs as well as for daisy-chaining the devices on the remote

network. Cabling in a rack system can be established using commercially available RJ-45 network cables.

However, CAN guidelines have to be observed for longer cable lengths. Both ends of the CAN-bus must be

terminated using 120 Ω terminating plugs.

The CAN bus allows using different data rates, whereas the data rate is inversely proportional to the bus

length. For smaller network setups, data rates can be as high as 500 kbit/s. For broader networks, reducing

the data rate becomes necessary (down to the minimum data rate of 10 kbit/s).

The following table illustrates the relation between data rate and bus length or network size. The use of CAN repeaters is

strongly recommended for busses that exceed 1000 meters in length.

HIGH LOW Address HIGH LOW Address

0 0 Stand-alone 8 0...F 128...143

0 1...F 1...15 9 0...F 144...159

1 0...F 16...31 A 0...F 160...175

2 0...F 32...47 B 0...F 176...191

3 0...F 48...63 C 0...F 192...207

4 0...F 64...79 D 0...F 208...223

5 0...F 80...95 E 0...F 224...239

6 0...F 96...111 F 0...A 240...250

7 0...F 112...127 F B...F reserved

Table 4.1: CAN addresses

NOTE:

The data rate of the CAN bus is preset to 10 kbit/s.

Transfer rate (in kbit/s) Bus length (in m)

500 100

250 250

125 500

62,5 1000

20 2500

10 5000

Table 4.2: Transfer rate and bus length

CONTRACTOR PRECISION SERIES

16 Owner‘s Manual

4 CONTROL PORT

The CONTROL PORT of the RCM-810 provides two control inputs, two control outputs and reference

connections for +5V and ground. The control inputs are configurable via IRIS-Net™. They can be used for

example for switching between power on / standby modes. The two control contacts IN1 and IN2 are

internally connected via pull-up resistors and carry +5V (open). The control inputs can be activated using

external switches, pushbuttons or relays to connect them to ground potential (pin 3). The two control outputs

OUT1 and OUT2 are open collector outputs, which are highly resistive in the non-active state (off). In active

state (on) the outputs are connected to ground. The control outputs are configurable via IRIS-Net™ and are

used to signal internal states. LEDs, indicators or relays can be driven directly. The +5V reference connector

provides voltage supply for connected components.

System Example

Illustration 4.2: Pin-assignment of CAN jack and CAN plug

Pin Name

Colour

T568A T568B

2 CAN_GND Green Orange

4CAN_H(+) Blue

5 CAN_L (-) Blue striped

Table 4.3: Overview CAN plug

CAUTION:

The maximally allowable current at the +5V output is 200 mA.

CONTRACTOR PRECISION SERIES

Owner‘s Manual 17

Page is loading ...

CONTRACTOR PRECISION SERIES

30 Owner‘s Manual / Bedienungsanleitung

Specifications/Technische Daten

Amplifier at rated conditions, both channels driven, 8 Ω load, unless otherwise specified.

Depending on the ambient temperature, the unit might not operate continously at 2 Ω load in Dual Mode or 4 Ω in Bridged Mode.

In addition input power exceeds 1.1 times rated power consumption with 2 Ω load in Dual Mode or 4 Ω load in Bridged Mode

CPS2.4 CPS2.6 CPS2.9 CPS2.12

Load Impedance 2 Ω 4 Ω 8 Ω 2 Ω 4 Ω 8 Ω 2 Ω 4 Ω 8 Ω 2 Ω 4 Ω 8 Ω

Maximum Midband Output Power

THD = 1%, 1 kHz, Dual Channel

650 W 450 W 270 W 900 W 600 W 380 W 1250 W 900 W 550 W 1800 W 1200 W 750 W

Rated Output Power

THD < 0.1%, 20 Hz...20 kHz

- 400 W 200 W - 500 W 250 W - 800 W 400 W - 1100 W 550 W

Maximum Single Channel Output Power

Dynamic-Headroom, IHF-A

1150 W 660 W 350 W 1700 W 950 W 480 W 2450 W 1400 W 700 W 3400 W 1800 W 950 W

Maximum Single Channel Output Power

Continuous, 1 kHz

850 W 540 W 310 W 1200 W 750 W 420 W 1700 W 1100 W 630 W 2400 W 1500 W 850 W

Maximum Bridged Output Power

THD = 1%, 1 kHz

- 1300 W 900 W - 1800 W 1200 W - 2800 W 1800 W - 3600 W 2400 W

Maximum RMS Voltage Swing

THD = 1%, 1 kHz

55.3 V 65.1 V 78.8 V 90.6 V

Power Bandwidth

THD = 1%, ref. 1 kHz, half power @ 4 Ω

< 10 Hz...30 kHz

Voltage Gain, ref. 1 kHz 32.0 dB

Input Sensitivity

rated power @ 8 Ω, 1 kHz

+2.2 dBu (1.0 V

rms

) +3.1 dBu (1.11 V

rms

) +5.1 dBu (1.39 V

rms

) +6.6 dBu (1.66 V

rms

)

THD at rated output power

MBW = 80 kHz, 1 kHz

< 0.03%

IMD-SMPTE, 60 Hz, 7 kHz < 0.1%

DIM30, 3.15 kHz, 15 kHz < 0.05%

Maximum Input Level +21 dBu (8.69 V

rms

)

Crosstalk

ref. 1 kHz, at rated output power

< -80 dB

Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB)

Input Impedance, active balanced 20 kΩ

Damping Factor, 1 kHz > 300

Slew Rate 25 V/μs 26 V/μs 27 V/μs 30 V/μs

Signal to Noise Ratio Amplifier

A-weighted

> 106 dB > 107 dB > 109 dB > 110 dB

Output Noise, A-weighted < -71 dBu

Output Stage Topology Class AB Class H

Power Requirements 240 V, 230 V, 120 V or 100 V; 50 Hz...60 Hz (factory configured)

Power Consumption

1/8 maximum output power @ 4 Ω

550 W 700 W 700 W 850 W

Mains Fuse 240 V / 230 V: T10AH;

120 V / 100 V: T20AH

240 V / 230 V: T12AH;

120 V / 100 V: T25AH

240 V / 230 V: T15AH;

120 V / 100 V: T25AH

240 V / 230 V: T15AH;

120 V / 100 V: T30AH

Protection Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters, Turn-

on delay

Cooling Front-to-rear, 3-stage-fans

Ambient Temperatur Limits +5 °C...+40 °C (40 °F...105 °F)

Safety Class I

Dimensions (W x H x D), mm 483 x 88.1 x 421.5

Weight 12.6 kg (27.8 lbs) 14.8 kg (32.6 lbs) 16.3 kg (35.9 lbs) 17.7 kg (39.0 lbs)

Signal Processing Lo-Cut 50 Hz / 18 dB, switchable

Optional 2-Way crossover, internal filter card, 24 dB, LR

500 Hz (NRS 90250), 800 Hz (NRS 90251)

CONTRACTOR PRECISION SERIES

Owner‘s Manual / Bedienungsanleitung 31

5.1 Mains Operation & Resulting Temperature

Power consumption is direct proportional for other mains voltages. The following conversion factors are meant for easy

conversion: 100V = 2.3; 120V = 1.9; 240V = 0.96

1) P

= Power Dissipation

2) 1 BTU = 1055.06 J = 1055.06 Ws

3) Sine Signal Modulation (1 kHz)

4) Pink Noise according to EN60065 / 7. Edition

5) 10% Mains Over Voltage

CPS2.4

mains

in V I

mains

in A P

mains

in W P

out

in W

BTU/hr

Idle

230 0.3 38 0 38 130

Max. Output Power @ 8 Ω

230 4.9 800 540 260 887

Max. Output Power @ 4 Ω

230 8.0 1450 900 550 1877

1/3 Max. Output Power @ 4 Ω

230 5.1 900 300 600 2047

1/8 Max. Output Power @ 4 Ω

230 3.4 550 112.5 437.5 1493

1/8 Max. Output Power @ 4 Ω

230 3.0 470 112.5 357.5 1220

1/8 Max. Output Power @ 4 Ω

4 5

253 3.2 560 135 425 1450

Normal Mode (-10 dB) @ 4 Ω

230 3.0 450 80 370 1262

Rated Output Power (0 dB) @ 4 Ω

230 7.6 1380 800 580 1979

Alert (Alarm) Mode (-3 dB) @ 4 Ω

230 5.7 1000 400 600 2047

Max. Output Power @ 2 Ω

230 12.1 2250 1300 950 3242

1/8 Max. Output Power @ 2 Ω

230 5.2 900 162.5 737.5 2516

1/8 Max. Output Power @ 2 Ω

230 4.8 750 162.5 587.5 2005

CPS2.6

mains

in V I

mains

in A P

mains

in W P

out

in W

BTU/hr

Idle

230 0.4 46 0 46 157

Max. Output Power @ 8 Ω

230 6.7 1110 760 350 1194

Max. Output Power @ 4 Ω

230 10.8 1970 1200 770 2627

1/3 Max. Output Power @ 4 Ω

230 6.9 1150 400 750 2559

1/8 Max. Output Power @ 4 Ω

230 4.6 740 150 590 2013

1/8 Max. Output Power @ 4 Ω

230 4.0 630 150 480 1638

1/8 Max. Output Power @ 4 Ω

4 5

253 4.5 760 190 570 1945

Normal Mode (-10 dB) @ 4 Ω

230 3.9 610 100 510 1740

Rated Output Power (0 dB) @ 4 Ω

230 10.0 1800 1000 800 2730

Alert (Alarm) Mode (-3 dB) @ 4 Ω

230 7.5 1320 500 820 2798

Max. Output Power @ 2 Ω

230 16.6 3260 1800 1460 4982

1/8 Max. Output Power @ 2 Ω

230 7.1 1160 225 935 3190

1/8 Max. Output Power @ 2 Ω

230 6.2 1040 225 815 2781

CONTRACTOR PRECISION SERIES

32 Owner‘s Manual / Bedienungsanleitung

Power consumption is direct proportional for other mains voltages. The following conversion factors are meant for easy

conversion: 100V = 2.3; 120V = 1.9; 240V = 0.96

1) P

= Power Dissipation

2) 1 BTU = 1055.06 J = 1055.06 Ws

3) Sine Signal Modulation (1 kHz)

4) Pink Noise according to EN60065 / 7. Edition

5) 10% Mains Over Voltage

CPS2.9

mains

in V I

mains

in A P

mains

in W P

out

in W

BTU/hr

Idle

230 0.4 46 0 46 157

Max. Output Power @ 8 Ω

230 9.4 1740 1100 640 2184

Max. Output Power @ 4 Ω

230 15.3 2810 1800 1010 3446

1/3 Max. Output Power @ 4 Ω

230 8.7 1450 600 850 2900

1/8 Max. Output Power @ 4 Ω

230 3.6 560 225 335 1143

1/8 Max. Output Power @ 4 Ω

230 3.6 540 225 315 1075

1/8 Max. Output Power @ 4 Ω

4 5

253 4.1 690 275 415 1416

Normal Mode (-10 dB) @ 4 Ω

230 3.2 460 160 300 1024

Rated Output Power (0 dB) @ 4 Ω

230 14.4 2640 1600 1040 3549

Alert (Alarm) Mode (-3 dB) @ 4 Ω

230 10.2 1770 800 970 3310

Max. Output Power @ 2 Ω

230 21.6 4090 2800 1290 4402

1/8 Max. Output Power @ 2 Ω

230 5.1 850 350 500 1706

1/8 Max. Output Power @ 2 Ω

230 5.0 810 350 460 1570

CPS2.12

mains

in V I

mains

in A P

mains

in W P

out

in W

BTU/hr

Idle

230 0.5 57 0 57 194

Max. Output Power @ 8 Ω

230 12.2 2100 1500 600 2047

Max. Output Power @ 4 Ω

230 19.7 3620 2400 1220 4163

1/3 Max. Output Power @ 4 Ω

230 11.2 1900 800 1100 3753

1/8 Max. Output Power @ 4 Ω

230 4.7 720 300 420 1433

1/8 Max. Output Power @ 4 Ω

230 4.7 705 300 405 1382

1/8 Max. Output Power @ 4 Ω

4 5

253 5.3 880 375 505 1723

Normal Mode (-10 dB) @ 4 Ω

230 4.1 625 220 405 1382

Rated Output Power (0 dB) @ 4 Ω

230 18.9 3340 2200 1140 3890

Alert (Alarm) Mode (-3 dB) @ 4 Ω

230 13.4 2330 1100 1230 4197

Max. Output Power @ 2 Ω

230 27.5 5165 3600 1565 5340

1/8 Max. Output Power @ 2 Ω

230 10.5 1810 450 1360 4640

1/8 Max. Output Power @ 2 Ω

230 10.2 1730 450 1280 4368

Page is loading ...

Subject to change withou prior notice. V3 1/16/09 / F01U076727

AMERICAS EUROPE, AFRICA & MIDDLE-EAST ASIA & PACIFIC RIM

Bosch Security Systems, Inc.

12000 Portland Ave South

Burnsville, MN 55337, USA

USA-Phone:1-800-392-3497

Fax: 1-800-955-6831

Canada-Phone: 1-866-505-5551

Fax:1-866-336-8467

Latin America-Phone: 1-952-887-5532

Fax: 1-952-736-4212

Bosch Sicherheitssysteme GmbH

Robert-Koch-Straße 100

D-85521 Ottobrunn, Germany

Contact & Visitor Address

EVI Audio GmbH

Hirschberger Ring 45

D-94315 Straubing, Germany

Phone: +49 9421 706-0

Fax: +49 9421 706-265

Telex Pte. Ltd.

3015A Ubi Road 1

05-10 Kampong Ubi

Industrial Estate

Singapore 408705

Phone: +65 6746-8760

Fax: +65 6746-1206

Electro-Voice CPS2.12 User manual

Brand: Electro-Voice

Model: CPS2.12

Category: Supplementary music equipment

Type: User manual

Download PDF

report

in other languages

Deutsch: Electro-Voice CPS2.12 Benutzerhandbuch

Electro-Voice CPS2.12 User manual

Electro-Voice CPS2.12 User manual

in other languages

Related papers

Other documents