Indesit TV 640 (WH) GH Owner's manual

Page is loading ...

HOB

Contents

Installation, 13-16

Positioning

Electrical connection

Gas connection

Burner and nozzle specifications

Description of the appliance, 17

Overall view

Start-up and use, 18-19

Practical advice on using the burners

Practical Advice on Using the Electric Hot Plates

Data plate

Precautions and tips, 20

General safety

Disposal

Maintenance and care, 21

Switching the appliance off

Cleaning the appliance

Gas tap maintenance

Troubleshooting, 22

Operating Instructions

Italiano, 1 Français, 23English,12

IT FR

GB

Nederlands, 36

NL

TV 631 GH

TV 631 E GH

TV 640 GH

TV 641 GH

TV 750 GH

TV 751 GH

GB

13

 Before operating your new appliance please read this

instruction booklet carefully. It contains important information

for safe use, installation and care of the appliance.

 Please keep these operating instructions for future

reference. Pass them on to possible new owners of the

appliance.

Positioning

 Keep packaging material out of the reach of children. It

can become a choking or suffocation hazard (see

Precautions and tips).

 The appliance must be installed by a qualified professional

according to the instructions provided. Incorrect installation

may cause harm to people and animals or may damage

property.

 This unit may be installed and used only in permanently

ventilated rooms in accordance with British Standard Codes

Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891

Current Editions. The following requirements must be

observed:

 The room must be equipped with an air extraction system

that expels any combustion fumes. This may consist of a

hood or an electric fan that automatically starts each time

the appliance is switched on.

 The room must also allow proper air circulation, as air is

needed for combustion to occur normally. The flow of air

must not be less than 2 m

3

/h per kW of installed power.

The air circulation system may

take air directly from the outside

by means of a pipe with an inner

cross section of at least 100 cm

2

;

the opening must not be

vulnerable to any type of

blockages.

The system can also provide the

air needed for combustion

indirectly, i.e. from adjacent rooms

fitted with air circulation tubes as

described above. However, these

rooms must not be communal

rooms, bedrooms or rooms that

may present a fire hazard.

 Liquid petroleum gas sinks to the floor as it is heavier

than air. Therefore, rooms containing LPG cylinders must

also be equipped with vents to allow gas to escape in

the event of a leak. As a result LPG cylinders, whether

partially or completely full, must not be installed or

stored in rooms or storage areas that are below ground

level (cellars, etc.). It is advisable to keep only the

cylinder being used in the room, positioned so that it is

not subject to heat produced by external sources

(ovens, fireplaces, stoves, etc. ) which could raise the

temperature of the cylinder above 50°C.

Fitting the appliance

Gas and mixed hobs are manufactured with type X

degree protection against overheating. The following

precautions must be taken when installing the hob:

 Kitchen cabinets adjacent to the appliance and taller

than the top of the hob must be at least 600 mm from

the edge of the hob.

 Hoods must be installed according to their relative

installation instruction manuals and at a minimum

distance of 650 mm from the hob.

 Place the wall cabinets adjacent to the hood at a

minimum height of 420 mm from the hob (see figure).

If the hob is installed beneath a

wall cabinet, the latter must be

situated at a minimum of 700 mm

above the hob (see figure).

 The installation cavity should have the dimensions

indicated in the figure.

Fastening hooks are provided, allowing you to fasten

the hob to tops that are between 20 and 40 mm thick.

To ensure the hob is securely fastened to the top, we

recommend you use all the hooks provided.

555

mm

475

m

55

mm

Hook fastening diagram

Hooking position Hooking position

for top H=20 mm for top H=30 mm

Installation

Enlarging the ventilation slot

between window and floor.

Adjacent

Room

Room to be

Vented

A

Examples of ventilation holes

for comburant air.

In a chimney stack or branched flue.

(exclusively for cooking appliances)

Directly to

the Outside

600mm min.

540mm min.

700mm min.

GB

14

Back

Hooking position Front

for top H=40 mm

 Use the hooks contained in the accessory pack

 Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This

must be placed at a minimum distance of 20 mm from

the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm (see diagrams).

! The hob can only be installed above built-in

ovens with a cooling ventilation system.

Electrical connection

Hobs equipped with a three-pole power supply cable are

designed to operate with alternating current at the voltage

and frequency indicated on the data plate (this is located

on the lower part of the appliance). The earth wire in the

cable has a green and yellow cover. If the appliance is to

be installed above a built-in electric oven, the electrical

connection of the hob and the oven must be carried out

separately, both for electrical safety purposes and to

make extracting the oven easier.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate.

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum contact

opening of 3 mm installed between the appliance and the

mains. The circuit-breaker must be suitable for the charge

indicated and must comply with current electrical

regulations (the earthing wire must not be interrupted by the

circuit-breaker). The supply cable must not come into

contact with surfaces with temperatures higher than 50°C.

 The installer must ensure that the correct electrical

connection has been made and that it is compliant with

safety regulations.

Before connecting to the power supply, make sure that:

 The appliance is earthed and the plug is compliant with

the law.

 The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

 The voltage is in the range between the values indicated

on the data plate.

 The socket is compatible with the plug of the appliance. If

the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

 Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

 The manufacturer declines any liability should these safety

measures not be observed.

Gas connection

The appliance should be connected to the main gas supply

or to a gas cylinder in compliance with current national

regulations. Before carrying out the connection, make sure

the cooker is compatible with the gas supply you wish to

use. If this is not the case, follow the instructions indicated in

the paragraph Adapting to different types of gas.

When using liquid gas from a cylinder, install a pressure

regulator which complies with current national regulations.

 Check that the pressure of the gas supply is consistent

with the values indicated in Table 1 (Burner and nozzle

specifications). This will ensure the safe operation and

longevity of your appliance while maintaining efficient

energy consumption.

Connection with a rigid pipe (copper or steel)

 Connection to the gas system must be carried out in such

a way as not to place any strain of any kind on the

appliance.

There is an adjustable L-shaped pipe fitting on the

appliance supply ramp and this is fitted with a seal in

order to prevent leaks. The seal must always be replaced

after rotating the pipe fitting (seal provided with

appliance). The gas supply pipe fitting is a threaded 1/2

gas cylindrical male attachment.

560 mm.

45 mm.

GB

15

Connecting a flexible jointless stainless steel pipe to a

threaded attachment

The gas supply pipe fitting is a threaded 1/2 gas

cylindrical male attachment.

These pipes must be installed so that they are never

longer than 2000 mm when fully extended. Once

connection has been carried out, make sure that the

flexible metal pipe does not touch any moving parts and

is not compressed.

 Only use pipes and seals that comply with current

national regulations.

Checking the tightness of the connection

 When the installation process is complete, check the

pipe fittings for leaks using a soapy solution. Never use a

flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than

default type (indicated on the rating plate at the base of

the hob or on the packaging), the burner nozzles should

be replaced as follows:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner,

and replace them with nozzles for

the new type of gas (see table 1

Burner and nozzle

characteristics).

In the case of

the Mini WOK, use a spanner

with a 7 mm opening to

unscrew the nozzle (see

figure).

3. Reassemble the parts following the above procedure in

the reverse order.

4. Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Sticker are available from any of our Service Centres.

Replacing the Mini DUAL burner nozzles

1. Remove the hob grids and slide the burners off their

seats. The burner consists of two separate parts.

2. Loosen the 3 screws and remove the burner.

3. Loosen the 2 screws (see figure).

4. Unscrew nozzle "A" using a 7

mm socket spanner. Use a

spanner with a 7 mm opening to

unscrew nozzle "B" (see figure).

Replace the nozzles with models

which are suitable for use with the

new type of gas (see table 1).

5. Replace all the components

by following the above instructions in reverse.

 Adjusting the burners primary air :

Does not require adjusting.

 Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust

the adjustment screw, which is

positioned in or next to the tap

pin, until the flame is small but

steady.

3. Having adjusted the flame to the required low setting,

while the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa

several times, checking that the flame does not go out.

4. Some appliances have a safety device (thermocouple)

fitted. If the device fails to work when the burners are

set to the low flame setting, increase this low flame

setting using the adjusting screw.

5. Once the adjustment has been made, replace the seals

on the by-passes using sealing wax or a similar

substance.

 If the appliance is connected to liquid gas, the regulation

screw must be fastened as tightly as possible.

 Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Stickers are available from any of our Service Centres.

 Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet pipe (in order

to comply with current national regulations).

A

B

GB

16

Burner and nozzle specifications

Table 1 Liquid gas Natural gas

Burner Diameter

(mm)

Thermal

power

kW

(p.c.s.*)

Thermal

power

kW

(p.c.s.*)

By-pass

1/100

(mm)

Nozzle

1/100

Flow*

g/h

Thermal

power

kW

(p.c.s.*)

Nozzler

1/100

Flow*

l/h

Nozzler

1/100

Flow*

l/h

Red. Nom. (mm) *** ** Nom. (mm) (mm)

Fast

(Large) (R)

100 0,70 3,00 39 86 218 214 3,00 116 286 143 286

Ultra Fast (UR) 100 0,70 3,40 39 91 247 243 3,40 123 324 135 248

Semi Fast

(Medium) (S)

75 0,40 1,65 28 64 120 118 1,65 96 157 105 157

Auxiliary

(Small) (A)

55 0,40 1,00 28 50 74 71 1,00 79 95 80 95

Mini WOK (MW) 110 1,30 3,50 57 91 254 250 3,50 138 343 155 333

Mini

DUAL

MD

internal

40 0,20 0,60 23 37 44 43 0,70 66 67 76 86

MD

external

108 1,30 4,00 54 93 291 286 4,00 135 381 124 438

Supply

pressures

Nominal (mbar)

Minimum (mbar)

Maximum (mbar)

28-30

20

35

37

25

45

20

17

25

13

6,5

18

*At 15°C and 1013 mbar - dry gas *** Butane P.C.S. = 49.47 MJ/Kg

** Propane P.C.S. = 50.37 MJ/Kg Natural P.C.S. = 37.78 MJ/m

3

A

S

RS

A

S

MWS

TV 751 GH

A A

UR

R

S

MD

R

S

TV 750 GH

MW

TV 640 GH

A

S

R

Ø 145

TV 631 E GH

A

TV 631 GH TV 641 GH

S

 The hob can only be installed above built-in ovens with a cooling ventilation system.

GB

17

Description of the

appliance

Overall view

*

Only available on certain models.

 The INDICATOR LIGHT FOR ELECTRIC

HOTPLATES / COOKTOP BROILER / CERAMIC

GLASS MODULE * switches on whenever the

selector knob is moved from the off position.

 GAS BURNERS differ in size and power. Use the

diameter of the cookware to choose the most

appropriate burner to cook with.

 Control Knobs for GAS BURNERS and ELECTRIC

HOTPLATE

S * adjust the power or the size of the

flame.

 GAS BURNER ignition * enables a specific burner

to be lit automatically.

 SAFETY DEVICE * stops the gas flow if the flame

is accidentally extinguished.

SAFETY

DEVICES *

Ignition for

GAS BURNERS *

Indicator Light for

ELECTRIC HOTPLATE*

Control Knobs for

GAS BURNERS

Control Knobs for

GAS BURNERS and

ELECTRIC HOTPLATE*

Support Grid for

COOKWARE

Support Grid for

COOKWARE

GAS BURNERS

ELECTRIC

HOTPLATE*

GB

18

 The position of the corresponding gas burner or

electric hotplate* is shown on every knob.

Gas burners

Each burner can be adjusted to one of the following

settings using the corresponding control knob:

 Off

Maximum

Minimum

To light one of the burners, hold a lit match or lighter

near the burner and, at the same time, press down

and turn the corresponding knob anti-clockwise to the

maximum setting.

Since the burner is fitted with a safety device, the

knob should be pressed for approximately 2-3

seconds to allow the automatic device keeping the

flame alight to heat up.

When using models with an ignition button, light the

desired burner pressing down the corresponding

knob as far as possible and turning it anticlockwise

towards the maximum setting.

 If a flame is accidentally extinguished, turn off the

control knob and wait for at least 1 minute before

trying to relight it.

To switch off the burner, turn the knob in a clockwise

direction until it stops (when reaches the  position).

The Mini DUAL burner*

This gas burner consists of two concentric flame

rings. Using both flame rings enables a higher

power level to be reached, thus reducing cooking

time with respect to the time required by traditional

burners. The double ring also enables heat to be

distributed across the base of the pan more evenly.

Cookware of all sizes may be used; when cooking

with small recipients use only the inner burner. The

burner is controlled with a single knob.

To light it, press the knob in fully and turn it in an

anticlockwise direction until it reaches the maximum

position

. The burner is equipped with an

electronic lighting system that is activated

automatically when the knob is pressed.

As the burner is fitted with a safety device, the

knob should be held down for approximately 2-3

seconds, until the automatic device keeping the

flame alight has heated up.

Each burner can be adjusted using the control knob

as follows:

 Off

On and inner ring set to maximum

Inner ring set to minimum

Both rings set to maximum

Both rings set to minimum

To switch off the burner, turn the knob in a clockwise

direction until it stops (when it reaches the 

position).

Practical advice on using the burners

For best performance, follow these general

guidelines:

 Use the appropriate cookware for each burner

(see table) in order to prevent the flame from

reaching the sides of the pot or pan;

 Alwasy use cookware with a flat bottom and keep

the lid on;

 When the contents of the pan reach boiling point,

turn the knob to minimum.

To identify the type of burner, refer to the designs in

the section entitled, "Burner and Nozzle

Specifications".

Bruciatore ø Diametro Recipienti(cm)

Ultra Rapid (UR) 24 – 26

Rapid (R) 24 – 26

Semi-Rapid (S) 16 – 20

Auxilliary (A) 10 – 14

Mini Dual (MD internal) 12 – 16

Mini Dual (MD external) 24 – 26

Start-up and use

*

Only available on certain models.

GB

19

! Do not use stainless steel flame spreaders,

bread toasters or meat grills over gas flames.

Practical Advice on Using the Electric

Hot Plates *

In order to avoid heat loss and damage to the hot

plate, use cookware with a flat bottom the diameter

of which is not less than that of the hot plate.

Setting Normal or Fast Plate

0

Off

1

Cooking vegetables, fish

2

Cooking potatoes (using steam) soups,

chickpeas, beans.

3

Continuing the cooking of large quantities of

food, minestrone

4

For roasting (average)

5

For roasting (above average)

6

For browning and reaching a boil in a short

time.

Before using the hot plates for the first time, you

should heat them at maximum temperature for

approximately 4 minutes, without any pans.

During this initial stag

e, their protective coating

hardens and reaches its maximum resistance.

*

Only available on certain models.

DATA PLAT E

Electrical

connections

voltage of 220-240V ~ 50/60Hz

maximum power absorbed

(see data plate )

This appliance conforms to the

following European Economic

Community directives:

-2006/95/EEC dated 12/12/06 (Low

Voltage) and subsequent

amendments

- 2004/108/EC dated 15/12/04

(Electromagnetic Compatibility)

and subsequent amendments

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 90/396/EEC dated 29/06/90 (Gas)

and subsequent amendments.

- 2002/96/EC and subsequent

amendments.

GB

20

Precautions and tips

 This appliance has been designed and

manufactured in compliance with international safety

standards. The following warnings are provided for

safety reasons and must be read carefully.

General safety

 This is a class 3 built-in appliance.

 Gas appliances require regular air exchange to

maintain efficient operation. When installing the

hob, follow the instructions provided in the

paragraph on Positioning the appliance.

 These instructions are only valid for the

countries whose symbols appear in the manual

and on the serial number plate.

 The appliance was designed for domestic use

inside the home and is not intended for commercial

or industrial use.

 The appliance must not be installed outdoors, even

in covered areas. It is extremely dangerous to leave

the appliance exposed to rain and storms.

 Do not touch the appliance with bare feet or with

wet or damp hands and feet.

 Th

e appliance must be used by adults only for

the preparation of food, in accordance with the

instructions outlined in this booklet. Any other

use of the appliance (e.g. for

heating the room)

constitutes improper use and is dangerous.

The manufacturer may not be held liable for

any damage resulting from improper, incorrect

and unreasonab

le use of the appliance.

 Ensure that the power supply cables of other

electrical appliances do not come into contact with

the hot parts of the oven.

 The openings used for ventilation and dispersion of

heat must never be covered.

 Always make sure the knobs are in the l/

¡

position when the appliance is not in use.

 When unplugging the appliance always pull the plug

from the mains socket, do not pull on the cable.

 Never carry out any cleaning or maintenance work

without having detached the plug from the mains.

 In case of malfunction, under no circumstances

should you attempt to repair the appliance yourself.

Repairs carried out by inexperienced persons may

cause injury or further malfunctioning of the

appliance. Contact a Service Centre (see

Assistance).

 Always make sure that pan handles are turned

towards the centre of the hob in order to avoid

accidental burns.

 Do not close the glass cover (if present) when the

gas burners or electric hotplates are still hot.

 Do not leave the electric hotplate switched on

without a pan placed on it.

 Do not use unstable or deformed pans.

 Remove any liquid from the lid before

opening it.

 The appliance should not be operated by people

(including children) with reduced physical,

sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with

the product. These individuals should, at the very

least, be supervised by someone who assumes

responsibility for their safety or receive

preliminary instructions relating to the operation of

the appliance.

 Do not let children play with the appliance.

Disposal

 When disposing of packaging material: observe

local legislation so that the packaging may be

reused.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE),

requires that old household electrical appliances

must not be disposed of in the normal unsorted

municipal waste stream. Old appliances must be

collected separately in order to optimise the

recovery and recycling of the materials they contain

and reduce the impact on human health and the

environment. The crossed out wheeled bin

symbol on the product reminds you of your

obligation, that when you dispose of the appliance

it must be separately collected.

Consumers may take their old appliance to public

waste collection areas, other communal collection

areas, or if national legislation allows return it to a

retailer when purchasing a similar new product.

All major household appliance manufacturers are

active in the creation of systems to manage the

collection and disposal of old appliances.

GB

21

Switching the appliance off

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Cleaning the appliance

 Do not use abrasive or corrosive detergents such

as stain removers, anti-rust products, powder

detergents or sponges with abrasive surfaces: these

may scratch the surface beyond repair.

 Never use steam cleaners or pressure cleaners on

the appliance.

 It is usually enough to wash the hob with a damp

sponge and dry it with absorbent kitchen roll.

 The removable parts of the burners should be

washed frequently with warm water and soap and

any burnt-on substances removed.

 For hobs which ligth automatically, the terminal

part of the electronic instant lighting devices

should be cleaned frequently and the gas outlet

holes should be checked for blockages.

 Before using the ceramic glass module, the

surface must be cleaned, using a damp cloth to

remove dust or food residues. The ceramic glass

surface should be cleaned regularly with a

soultion of warm water and a non-abrasive

detergent. Periodically, special products will need

to be used to clean

the surface. First,

remove all food

buildup or grease

with a cleaning

scraper, e.g.

(not

supplied.

Clean the cooking

surface when it is

still warm with a

suitable cleaning product (such as the one in the

Solutions product line available from any After-

Sales Service Centre) and paper towels. Then rub

Maintenance and care

with a damp cloth and dry. Aluminum foil, plastic

items, objects made of synthetic material, sugar

or foods with a high sugar content that have

melted onto the surface must be removed

immediatley with a scraper while the cooking

surface is still hot. Special cleaning products for

ceramic glass surfaces form a transparent

protective layer which fights diry buildup. This

also protects the

surface from damage

caused by food with

a high sugar content.

Do not use abrasive

sponges or cleaning

products under any

circumstances. This

holds true for

chemically

aggressive cleaners,

like oven sprays and stain removers.

Gas tap maintenance

Over time, the taps may become jammed or difficult

to turn. If this happens, the tap must be replaced.

 This procedure must be performed by a

qualified technician authorised by the

manufacturer.

GB

22

Troubleshooting

It may happen that the appliance does not function properly or at all. Before calling the service centre for

assistance, check if anything can be done. First, check to see that there are no interruptions in the gas and

electrical supplies, and, in particular, that the gas valves for the mains are open.

Problem

The burner does not light or the flame is not

even around the burner.

The flame dies in models with a safety device.

The burner does not

remain lit when set to

minimum.

The cookware is unstable.

Possible causes/Solution

 The gas holes on the burner are clogged.

 All the movable parts that make up the burner are

mounted correctly.

 There are draughts near the appliance.

 You pressed the knob all the way in.

 You keep the knob pressed in long enough to activate the

safety device.

 The gas holes are not blocked in the area corresponding

to the safety device.

 The gas holes are not blocked.

 There are no draughts near the appliance.

 The minimum setting has been adjusted properly.

 The bottom of the cookware is perfectly flat.

 The cookware is positioned correctly at the centre of the

burner.

 The pan support grids have been positioned correctly.

If, despite all these checks, the hob does not function properly and the problem persists, call the nearest

Customer Service Centre. Please have the following information handy:

 The appliance model (Mod.).

 The serial number (S/N).

This information can be found on the data plate located on the appliance and/or on the packaging.

 Never use unauthorised technicians and never accept replacement parts which are not original.

Page is loading ...

Indesit TV 640 (WH) GH Owner's manual

Indesit TV 640 (WH) GH Owner's manual

in other languages

Related papers

Other documents