Livex Lighting 50913-07 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
50913-07
Type
Operating instructions

This manual is also suitable for

Livex Lighting 50913-07 is a ceiling-mounted light fixture, suitable for indoor use. It features a single light bulb and a glass shade, which can be locked securely in place with a screw. The fixture can be installed on a junction box, and the electrical wires can be connected easily by following the instructions in the manual. The fixture is compatible with different types of light bulbs, including incandescent, LED, and fluorescent, as long as they do not exceed the specified wattage.

Livex Lighting 50913-07 is a ceiling-mounted light fixture, suitable for indoor use. It features a single light bulb and a glass shade, which can be locked securely in place with a screw. The fixture can be installed on a junction box, and the electrical wires can be connected easily by following the instructions in the manual. The fixture is compatible with different types of light bulbs, including incandescent, LED, and fluorescent, as long as they do not exceed the specified wattage.

ASSEMBLING & INSTALLATION INSTRUCTIONS FOR PRODUCT#
50901 50911 50903 50913 For Ceiling Mount Fixtures
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ATTENTION! COUPER LE COURANT AU FUSIBLE OU LE DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old
fixture and all hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a
clear area. Take care not to lose any small parts necessary for
installation.
3. Install the light bulbs in accordance with the fixture’s
specifications. NOTE: DO NOT EXCEED THE
SPECIFIED WATTAGE!
4. Raise the glass shade (D) to the lamp holder, lock it securely
with screw(C) until snug.
5. Thread the two mounting screws about 1/4” into the pre-drilled
holes in the single bar spaced the same distance apart as the
holes in the fixture canopy.
6. Install the single bar to the Junction Box with the two Box
Screws as shown. The side of the single bar marked "GND"
must face out. The junction box is not included.
7. While holding the lamp(A) towards the ceiling, connect the
electrical wires as Shown in Fig.2, making sure that all wire
nuts are secured. You may have to wrap the connections with
electrical tape. If your outlet has a ground wire (green or bare
copper), connect the fixture ground wire to it. Otherwise
connect fixture’s ground wire directly to the Mounting strap
with the green screw provided. After wires are connected, tuck
them carefully inside the Junction Box.
8. Attach the fixture canopy on to the junction box, aligning
screws on single bar with mounting holes in canopy and lock it
securely with ball nut (B).
Your installation is now complete Return power to the
junction box and test the fixture.
Fig.1
Fig.2
Page 1 of 1 DOC20150350901
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
  • Page 1 1

Livex Lighting 50913-07 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
50913-07
Type
Operating instructions
This manual is also suitable for

Livex Lighting 50913-07 is a ceiling-mounted light fixture, suitable for indoor use. It features a single light bulb and a glass shade, which can be locked securely in place with a screw. The fixture can be installed on a junction box, and the electrical wires can be connected easily by following the instructions in the manual. The fixture is compatible with different types of light bulbs, including incandescent, LED, and fluorescent, as long as they do not exceed the specified wattage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents