GE GIE19JSNRSS Installation guide

Brand: GE

Model: GIE19JSNRSS

Category: Fridges

Type: Installation guide

This manual is also suitable for

GTS19KGNRBB

49-1000394 Rev. 2 9

ROLLERS AND LEVELING LEGS

Leveling legs near each front corner of the refrigerator

are adjustable. They firmly position the refrigerator

and prevent it from moving when the doors are

opened. Leveling legs should be set so the front of

the refrigerator is raised just enough that the doors

close easily when opened about halfway.

Turn the leveling legs clockwise to raise the

refrigerator, counterclockwise to lower it.

Rollers next to the leveling legs allow you to move the

refrigerator away from the wall for cleaning.

Turn the legs counterclockwise until the weight of the

refrigerator is transferred from them to the rollers.

After rolling the refrigerator back into place, turn the

legs clockwise until the legs again bear the weight of

the refrigerator.

Installation Instructions Models 16, 17, 18, 19, & 22

CLEARANCES

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

6LGHV´PP

7RS´PP

%DFN´PPRQFXIWPRGHOV

• Back 1" (25 mm) on 16 & 17 cuft models

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use.

• IMPORTANT – Observe all governing codes

and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – .HHSWKHVHLQVWUXFWLRQV

for future reference.

• Skill level±,QVWDOODWLRQRIWKLVDSSOLDQFHUHTXLUHV

basic mechanical skills.

• Completion time±5HIULJHUDWRU,QVWDOODWLRQ

15 minutes

  5HYHUVLQJWKH'RRU6ZLQJ

15 minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

REFRIGERATOR LOCATION

• 'RQRWLQVWDOOWKHUHIULJHUDWRUZKHUHWKHWHPSHUDWXUH

will go below 55°F (12.7°C) because it will not run

often enough to maintain proper temperatures.

• 'RQRWLQVWDOOWKHUHIULJHUDWRUZKHUHWKH

temperature will go above 100°F (37°C) because

it will not perform properly.

• 'RQRWLQVWDOOWKHUHIULJHUDWRULQDORFDWLRQH[SRVHG

to water (rain, etc.) or direct sunlight.

,QVWDOOLWRQDIORRUVWURQJHQRXJKWRVXSSRUWLWIXOO\

loaded.

WATER SUPPLY TO THE ICE

MAKER (on some models)

,IWKHUHIULJHUDWRUKDVDQLFHPDNHULWZLOOKDYHWR

be connected to a cold water line. A water supply

kit (containing copper tubing, shutoff valve, fittings

and instructions) is available at extra cost from your

dealer, by visiting our Website at GEAppliances.

com (in Canada at geappliances.ca) or from Parts

and Accessories, 1.877.959.8688. See instructions

,QVWDOOLQJWKH:DWHU/LQH

If you have questions, call 1.800.GE.CARES or visit our Website at: GEAppliances.com.

In Canada, call 1.800.561.3344 or Visit our Website at: geappliances.ca

INSTALLATION INSTRUCTIONS

10 49-1000394 Rev. 2

Installation Instructions

INSTALLING THE WATER LINE (on some models)

BEFORE YOU BEGIN

5HFRPPHQGHGFRSSHUZDWHUVXSSO\NLWVDUH:;;

:;;RU:;;GHSHQGLQJRQWKHDPRXQWRI

tubing you need. Approved plastic water supply

lines are SmartConnect

™

Refrigerator Tubing

:;;:;;DQG:;;

When connecting your refrigerator to a GE

Appliances Reverse Osmosis Water System, the only

DSSURYHGLQVWDOODWLRQLVZLWKD*($SSOLDQFHV59.LW

For other reverse osmosis water systems, follow the

manufacturer’s recommendations.

This water line installation is not warranted by the

refrigerator or ice maker manufacturer. Follow these

LQVWUXFWLRQVFDUHIXOO\WRPLQLPL]HWKHULVNRIH[SHQVLYH

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and

lead to water leakage or flooding. Call a qualified

plumber to correct water hammer before installing the

water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

,I\RXXVH\RXUUHIULJHUDWRUEHIRUHFRQQHFWLQJWKH

water line, make sure the ice maker power switch

is in the OFF position (on power switch models) or

operating arm is in OFF position.

'RQRWLQVWDOOWKHLFHPDNHUWXELQJLQDUHDVZKHUH

WHPSHUDWXUHVIDOOEHORZIUHH]LQJ

When using any electrical device (such as a power

drill) during installation, be sure the device is double

insulated or grounded in a manner to prevent the

KD]DUGRIHOHFWULFVKRFNRULVEDWWHU\SRZHUHG

All installations must be in accordance with local

plumbing code requirements.

WARNING

Connect to potable water supply

only.

WHAT YOU WILL NEED

• Copper or SmartConnect™ Refrigerator Tubing kit,

´RXWHUGLDPHWHUWRFRQQHFWWKHUHIULJHUDWRUWRWKH

ZDWHUVXSSO\,IXVLQJFRSSHUEHVXUHERWKHQGVRI

the tubing are cut square.

To determine how much tubing you need: measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add 6’

(1.8 m). Be sure there is sufficient extra tubing (about

¶>P@FRLOHGLQWRWXUQVRIDERXW´>FP@

diameter) to allow the refrigerator to move out from

the wall after installation.

WHAT YOU WILL NEED (Cont.)

6PDUW&RQQHFW5HIULJHUDWRU7XELQJ.LWVDUHDYDLODEOH

in the following lengths:

¶P±:;;

¶P±:;;

¶P±:;;

Be sure that the kit you select allows at least 6’

(1.8 m) as described above.

NOTE: The only GE Appliances approved plastic

tubing is that supplied in SmartConnect™ Refrigerator

7XELQJNLWV'RQRWXVHDQ\RWKHUSODVWLFZDWHUVXSSO\

line because the line is under pressure at all times.

Certain types of plastic will crack or rupture with age

and cause water damage to your home.

• A GE Appliances water supply kit (containing tubing,

shutoff valve and fittings listed below) is available

at extra cost from your dealer or from Parts and

Accessories, 877.959.8688.

• A cold water supply. The water pressure must be

between 20 and 120 psi (138 – 827 kilopascals) on

models without a water filter and between 40 and

120 psi (275 – 827 kilopascals) on models with a

water filter.

• Power drill.

´RUDGMXVWDEOHZUHQFK

• Straight and Phillips blade

screwdriver.

7ZR´RXWHUGLDPHWHU

compression nuts and 2 ferrules

VOHHYHV²WRFRQQHFWWKHFRSSHU

tubing to the shutoff valve and

the refrigerator water valve.

,I\RXDUHXVLQJD6PDUW&RQQHFW5HIULJHUDWRU

Tubing kit, the necessary fittings are preassembled

to the tubing.

,I\RXUH[LVWLQJFRSSHUZDWHUOLQHKDVDIODUHGILWWLQJ

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression

ILWWLQJ'RQRWFXWIRUPHGHQGIURP6PDUW&RQQHFW

Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

PLQLPXPLQVLGHGLDPHWHURI´DWWKHSRLQWRI

FRQQHFWLRQWRWKH&2/':$7(5/,1(6DGGOH

type shutoff valves are included in many water

supply kits. Before purchasing,

make sure a saddle-type valve

complies with your local plumbing

codes.

INSTALLATION INSTRUCTIONS

49-1000394 Rev. 2 11

INSTALLATION INSTRUCTIONS

Installation Instructions

INSTALLING THE WATER LINE (Cont.)

SHUT OFF THE MAIN WATER

SUPPLY AND UNPLUG

REFRIGERATOR

Turn on the nearest faucet (counterclockwise)

long enough to clear the line of water.

CHOOSE THE VALVE LOCATION

Choose a location for the valve that

LVHDVLO\DFFHVVLEOH,WLVEHVWWR

connect into the side of a vertical

water pipe. When it is necessary

WRFRQQHFWLQWRDKRUL]RQWDOZDWHU

pipe, make the connection to the

top or side, rather than at the

bottom, to avoid drawing off any

sediment from the water pipe.

ROUTE THE TUBING

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 6 feet [1.82 m] coiled into 2 turns of about

´>FP@GLDPHWHUWRDOORZWKHUHIULJHUDWRUWR

move out from the wall after installation.

CONNECT THE TUBING TO THE

VALVE

Place the compression nut and ferrule (sleeve)

for copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the

valve. Tighten the compression nut securely.

For plastic tubing from a SmartConnect™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle

valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed plumber.

DRILL THE HOLE FOR THE VALVE

'ULOOD´KROHLQWKHZDWHUSLSHHYHQLIXVLQJD

self-piercing valve), using a sharp bit. Remove any

burrs resulting from drilling

the hole in the pipe. Take

care not to allow water to

drain into the drill. Failure to

GULOOD´KROHPD\UHVXOW

in reduced ice production or

smaller cubes.

FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe

with the pipe clamp.

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: 'RQRWRYHUWLJKWHQRU\RXPD\FUXVKWKH

tubing.

FASTEN THE SHUTOFF VALVE

(Cont.)

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle

valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed plumber.

Washer

,QOHW(QG

Clamp

Screw

Vertical Cold

Water Pipe

Saddle-Type

6KXWRႇ9DOYH

Pipe Clamp

Saddle-Type

6KXWRႇ9DOYH

Compression

Nut

SmartConnect

™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

FLUSH OUT THE TUBING

Turn the main water supply on

(counterclockwise) and flush out the

tubing until the water is clear.

Shut the water off at the water valve

after about one quart (1 liter) of water

has been flushed through the tubing.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING

To reduce the risk of

electric shock or injury during installation,

you must first unplug the refrigerator

before proceeding.

12 49-1000394 Rev. 2

Installation Instructions

INSTALLING THE WATER LINE (Cont.)

CONNECT THE TUBING TO THE

REFRIGERATOR

NOTES:

• Before making the connection to the

refrigerator, be sure the refrigerator power cord

is not plugged into the wall outlet.

• We recommend installing a water filter

*;5/4DYDLODEOHRQJewaterfilters.com

or 877.959.8688) if your water supply has

sand or particles that could clog the screen

RIWKHUHIULJHUDWRU¶VZDWHUYDOYH,QVWDOOLWLQ

WKHZDWHUOLQHQHDUWKHUHIULJHUDWRU,IXVLQJ

SmartConnect™ Refrigerator Tubing kit, you

ZLOOQHHGDQDGGLWLRQDOWXEH:;;

WRFRQQHFWWKHILOWHU'RQRWFXWSODVWLFWXEHWR

install filter.

WARNING

To reduce the risk of death

or electric shock, you must follow these

instructions:

Ŷ Unplug the refrigerator before removing

any panels.

Ŷ Do not damage any wiring while the panel

is removed.

Ŷ Replace all parts and panels before

plugging the refrigerator back in.

• Remove the access

cover.

• Remove the plastic

flexible or screw cap

from the water valve

(refrigerator connection) and

discard.

• Place the compression nut and

ferrule (sleeve) onto the end

of the tubing as shown. On

SmartConnect™ Refrigerator Tubing kit, the

nuts are already assembled to the tubing.

 ,QVHUWWKHHQGRIWKHWXELQJLQWRWKHZDWHUYDOYH

connection as far as possible. While holding

the tubing, tighten the fitting.

• For plastic tubing from a SmartConnect™

Refrigerator Tubing kit, insert the molded

end of the tubing into the shutoff valve and

tighten compression nut until it is hand tight,

then tighten one additional turn with a wrench.

Overtightening may cause leaks.

• Fasten the tubing into the clamp provided to hold

it in a vertical position. You may need to pry open

the clamp.

TURN THE WATER ON AT THE

SHUTOFF VALVE

Tighten any connections that

leak.

CONNECT THE TUBING TO THE

REFRIGERATOR (Cont.)

• Reattach the access

cover.

Tubing

Clamp

´

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

´

Copper

Tubing

INSTALLING THE

REFRIGERATOR

Plug in the refrigerator.

Arrange the coil of tubing so that it

does not vibrate against the back of

the refrigerator or against the wall.

Push the refrigerator back to the

wall.

START THE ICE MAKER

Set the ice maker power switch to the

0N position. The ice maker will not begin

to operate until it reaches its operating

temperature

of 15°F

(–9°C) or

EHORZ,WZLOO

then begin

operation

automatically.

OFF

Power

switch

Power switch model

WARNING

ELECTRIC SHOCK

HAZARD

Attach tubing clamp using existing hole only.

'2127GULOOLQWRWKHUHIULJHUDWRU

INSTALLATION INSTRUCTIONS

49-1000394 Rev. 2 13

INSTALLATION INSTRUCTIONS

Installation Instructions

INSTALLING THE DOOR HANDLE

PLASTIC HANDLE

,QVWDOOWKHKDQGOHIDVWHQHULQWRWKHKROHRQWKH

IUHH]HUDQGIUHVKIRRGGRRUV7KHIDVWHQHUV

correspond with the handle side (the side

opposite the hinge).

STAINLESS STEEL HANDLE

Attach plastic bushing to the door with the

screw on both freezer and fresh food doors. The

fasteners correspond with the handle side (the

side opposite the hinge).

HANDLE INSTALLATION

$WWDFKKDQGOHWRIUHH]HUGRRUE\VOLGLQJKDQGOH

up onto plastic bushing or fastener with the

screws at the bottom of the handle.

2. Attach handle to fresh food door by sliding

handle down onto plastic bushing or fastener

with the screws at top of handle.

BADGE AND PLUG BUTTON

INSTALLATION

1. Place a plug button on the opposite side of the

fresh food door across from the handle.

2. Remove the backing on the GE Appliances

badge and carefully place it in the hole

RSSRVLWHWKHKDQGOHRQWKHIUHH]HUGRRU%H

sure the badge is oriented the correct way

before applying it to the door.

Handle Fastener

NOTE: Be sure to remove

¿OPEHIRUHKDQGOHLQVWDOODWLRQ

if applicable)

Plug

button

Badge

Bushing

with Screw

14 49-1000394 Rev. 2

REVERSING THE DOOR SWING

Installation Instructions

BEFORE YOU START

8QSOXJWKHUHIULJHUDWRUIURPLWVHOHFWULFDO

outlet.

1.2 Empty all door shelves, including the dairy

compartment.

CAUTION

'RQRWOHWHLWKHUGRRUGURSWRWKH

floor. To do so could damage the door stop.

REMOVE THE FREEZER DOOR

2.1 Tape the

door shut with

masking tape.

2.2 Remove the

screws that

hold the top

hinge to the

cabinet.

2.3 Lift the hinge

straight up to free

the hinge pin from

the socket in the top

of the door and set

it aside, along with

its screws.

2.4 Remove the tape.

Lift it off the center

hinge pin.

2.5 Set the door on a non-scratching surface with

the outside up.

2.6 Transfer the 2 screws from the opposite side

of the cabinet to the screw holes vacated by

the top hinge removal.

TOOLS REQUIRED

IMPORTANT NOTES:

When reversing the door swing:

• Read the instructions all the way through before

starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid

losing them.

• Provide a non-scratching work surface for the doors.

IMPORTANT: Once you begin, do not move the

cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from

WKHULJKWVLGHWRWKHOHIWVLGH²LI\RXHYHUZDQWWR

change the hinges back to the right side, follow these

same instructions and reverse all references to left

and right.

CAUTION

Lifting Hazard

7KHIUHVKIRRGDQGIUHH]HUGRRUVDUHKHDY\8VHERWK

hands to secure the doors before lifting.

Phillips screwdriver

Masking tape

´KH[KHDG

socket driver

(optional)

´RSHQHQG

wrench (optional)

Putty knife or

thin-blade screwdriver

(optional)

Allen wrench (Stainless

Steel Handle Models)

Top Hinge

WARNING

Follow all steps when reversing

the door swing. Failure to follow these instructions,

leaving off parts, or overtightening screws, can lead

to the door falling off and result in injury and property

damage.

INSTALLATION INSTRUCTIONS

49-1000394 Rev. 2 15

INSTALLATION INSTRUCTIONS

Installation Instructions

REVERSING THE DOOR SWING (Cont.)

REMOVE THE FRESH FOOD

DOOR

3.1 Tape the door shut

with masking tape.

8QVFUHZWKHFHQWHU

hinge pin and remove

it from its socket. Be

careful not to lose

the center hinge and

washer.

3.3 Remove the tape and tilt the door away from

the cabinet. Lift the door from the pin in the

ERWWRPKLQJH,IWKHSODVWLFZDVKHUVWLFNVWR

the door bottom, put it back on the hinge.)

3.4 Set the door outside-up on a non-scratching

surface.

REVERSING THE HARDWARE

,QWHUFKDQJHWKHKLQJHDQGVFUHZVDWWRS

ULJKWZLWKVFUHZVDWWRSOHIWRIFDELQHW'RQRW

tighten screws on hinge side.

NOTE: Some hinges have 4 holes. Which

holes you use for installing depends on which

side you install the hinge.

The outer edge of the hinge should be

parallel to the edge of the case for correct

installation.

4.2 Remove the three screws holding the center

hinge to the cabinet.

4.3 Transfer the three screws from the opposite

side of the cabinet to the screw holes vacated

by the center hinge removal.

4.4 Reattach the center hinge with all three

screws on the left side of the cabinet.

NOTE: The center hinge must be turned over

as shown when mounted on the left side.

4.5 Remove the screws holding the bottom hinge

to the cabinet. Move the bottom hinge from

the right to left side of the cabinet. Switch the

hinge pin to the opposite side of the hinge

and reinsert the screws.

Center

Hinge Pin

Washer

Plastic

Washer

Hinge

Plastic

Washer

Hinge

Bracket

Hinge

Bracket

Switch the

hinge pin to the

opposite side of

the bracket.

WARNING

Follow all steps when reversing

the door swing. Failure to follow these instructions,

leaving off parts, or overtightening screws, can lead

to the door falling off and result in injury and property

damage.

16 49-1000394 Rev. 2

Installation Instructions

REVERSING THE DOOR SWING (Cont.)

REVERSING THE DOOR HANDLES

5.1. Remove handle screws from the top of fresh

food door. Remove handle screws from the

ERWWRPRIIUHH]HUGRRU

5.2. Remove door handle on fresh food door by

sliding the handle up off of the fastener (Plastic

Handle) or plastic bushing (Stainless Steel

+DQGOH5HPRYHGRRUKDQGOHRQIUHH]HUGRRU

by sliding the handle down off of the fastener

(Plastic Handle) or plastic bushing (Stainless

Steel Handle).

5.3. Change places between the handle fastener or

plastic bushing and plug button on door front.

5.4. Move the plug buttons on top and front of the

door to fill the now vacant holes.

5.5. Transfer the door stop on the bottom of the

door.

5.6. Attach handle to fresh food door by sliding

handle down onto fastener (Plastic Handle) or

plastic bushing (Stainless Steel handle) and

with screws at top of handle.

$WWDFKKDQGOHWRIUHH]HUGRRUE\VOLGLQJKDQGOH

up onto fastener (Plastic Handle) or plastic

bushing (Stainless Steel handle) and with

screws at bottom of handle.

$WWDFKEDGJHRQIUHH]HUGRRURSSRVLWHWKH

handle.

'RRU

Stop

INSTALLATION INSTRUCTIONS

49-1000394 Rev. 2 17

INSTALLATION INSTRUCTIONS

Installation Instructions

REVERSING THE DOOR SWING (Cont.)

RE-HANGING THE DOORS

6.1 Re-hang the fresh food door

6.1.1 Lower the fresh food door onto the

bottom hinge pin. Be sure the washer is

in place on the pin.

6.1.2 Tilt the door towards the cabinet. As

the door is brought into position, align

the socket in the door with the hole

in the center hinge. Place the center

hinge pin into the hole in the center

hinge and tighten. Make sure the

washer is on the top of the hinge pin.

RE-HANGING THE DOORS (CO

6.1 Re-hang the fresh food door

 /RZHUWKHIUHH]HUGRRURQWRWKHFHQWHU

hinge pin. Be sure the washer is in

place on the pin.

6.2.2 Tilt the door towards the cabinet, lifting

the top hinge so the pin fits into the

socket on the top of the door.

6.2.3 Make sure the door is slightly above

the top of the cabinet and the gap

between the doors is even across the

IURQW7LJKWHQWKHWRSKLQJHVFUHZV'R

not over-tighten these screws. Tighten

them until they are just snug, and then

turn them another one-half turn.

Plastic

Washer

Hinge

Pin with

Washer

Center

Hinge

Plastic

Washer

Top

Hinge

Gap

GE GIE19JSNRSS Installation guide

Brand: GE

Model: GIE19JSNRSS

Category: Fridges

Type: Installation guide

This manual is also suitable for

GTS19KGNRBB

Download PDF

report

GE GIE19JSNRSS Installation guide

This manual is also suitable for

GE GIE19JSNRSS Installation guide

Related papers

Other documents