Contec COM-4PD-PE Owner's manual

PC-HELPER

RS-422A/485 Isolated Serial I/O Board

for PCI Express

2ch

COM-2PD-PE

4ch

COM-4PD-PE

User’s Guide

CONTEC CO.,LTD.

1. Before Using the Product

Check Your Package

Thank you for purchasing the CONTEC product.

The product consists of the items listed below.

Check, with the following list, that your package is complete. If you discover damaged or missing

items, contact your retailer.

Product Configuration List

- Board(One of the following) …1

[COM-2PD-PE, COM-4PD-PE]

- First step guide … 1

- COM Setup Disk *1 (CD-ROM) …1

- Warranty Certificate …1

- Serial No. Label…1

*1 The CD-ROM contains the driver software and User’s Guide (this guide)

XXXXXXXXXXXXX

Serial No. Label

XXXXXXXXXXXXX

First step guide

CD-ROM *1

[COM Setup Disk]

Board

Warranty Certificate

Warranty

Certificate

COM-2PD-PE, COM-4PD-PE

1

1. Before Using the Product

Copyright

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this

document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an

omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may

appear in this document or for results obtained by the user as a result of using this product.

Trademarks

MS, Microsoft, Windows, Windows NT are trademarks of Microsoft Corporation. Other brand and

product names are trademarks of their respective holder.

2

COM-2PD-PE, COM-4PD-PE

1. Before Using the Product

Table of Contents

Check Your Package .................................................................................................................................... i

Copyright ..................................................................................................................................................... 2

Trademarks .................................................................................................................................................. 2

Table of Contents ........................................................................................................................................ 3

1. BEFORE USING THE PRODUCT 5

About the Board .......................................................................................................................................... 5

Features ................................................................................................................................................. 5

Support Software.................................................................................................................................. 7

Cable & Connector (Option)............................................................................................................ 8

Customer Support ........................................................................................................................................ 9

Web Site http ........................................................................................................................................ 9

Limited Three-Years Warranty .................................................................................................................. 9

How to Obtain Service ................................................................................................................................ 9

Liability ........................................................................................................................................................ 9

Safety Precautions ..................................................................................................................................... 10

Safety Information ............................................................................................................................. 10

Handling Precautions ......................................................................................................................... 11

Environment ....................................................................................................................................... 12

Inspection............................................................................................................................................ 12

Storage ................................................................................................................................................ 12

Disposal .............................................................................................................................................. 12

2. SETUP 13

What is Setup? ........................................................................................................................................... 13

Using the Board under Windows Using the Standard COM Driver Software COM Setup Disk13

Using the Board under Windows Using the Driver Library API-PAC(W32) .............................. 13

Using the Board under Linux Using the Standard COM Driver Software COM Setup Disk ..... 14

Operating Systems Other than Windows or Linux ......................................................................... 14

Step 1 Setting the Hardware ..................................................................................................................... 15

Parts of the Board and Factory Defaults .......................................................................................... 15

Setting the Board ID .......................................................................................................................... 17

Setting Transmission Mode .............................................................................................................. 18

Setting of Terminator......................................................................................................................... 19

Plugging the Board ............................................................................................................................ 22

Step 2 Installing the Hardware ................................................................................................................. 23

Turning on the PC .............................................................................................................................. 23

Windows 8.1/ 8/ 7, Server 2012 ....................................................................................................... 24

Windows Server 2008, Windows Vista ........................................................................................... 26

Windows Server 2003, Windows XP/ 2000 .................................................................................... 27

COM-2PD-PE, COM-4PD-PE

3

1. Before Using the Product

The check method of the completion of hardware installation ...................................................... 28

Step 3 Initializing the Software................................................................................................................ 29

Step 4 Checking Operations with the Diagnosis Program..................................................................... 33

What is the Diagnosis Program? ...................................................................................................... 33

Check Method .................................................................................................................................... 33

Using the Diagnosis Program ........................................................................................................... 34

Setup Troubleshooting .............................................................................................................................. 36

Symptoms and Actions ...................................................................................................................... 36

If your problem cannot be resolved.................................................................................................. 36

3. EXTERNAL CONNECTION 37

In the case of COM-2PD-PE .................................................................................................................... 37

Connecting directly to the port connector ....................................................................................... 37

In the case of COM-4PD-PE .................................................................................................................... 39

Converting the Interface Connector to 9-pin D-SUB, Male Connectors ................................... 39

Connecting directly to the port connector ....................................................................................... 40

Types of Cable and Example Connections ............................................................................................. 41

4. FUNCTIONS 43

Communication Function ......................................................................................................................... 43

Serial Data Transmission .................................................................................................................. 43

RS-422A/485 Control Lines ............................................................................................................. 43

Send and Receive Data Buffers ........................................................................................................ 43

Setting the Baud Rate ........................................................................................................................ 44

Automatic RTS Control Functions ................................................................................................... 46

Other Functions ......................................................................................................................................... 46

Channel Isolation/Bus Isolation ....................................................................................................... 46

Surge Protection ................................................................................................................................. 46

5. ABOUT SOFTWARE 47

About Sample programs ........................................................................................................................... 47

Uninstalling the driver software............................................................................................................... 49

Windows 8.1/ 8/ 7/ Vista, Server 2012/ 2008 ................................................................................. 49

Windows XP/ 2000, Server 2003 ..................................................................................................... 49

CD-ROM Directory Structure .................................................................................................................. 50

6. ABOUT HARDWARE 51

For detailed technical information ........................................................................................................... 51

Hardware specification ............................................................................................................................. 51

Different in the specification .................................................................................................................... 55

4

COM-2PD-PE, COM-4PD-PE

1. Before Using the Product

1.

Before Using the Product

This chapter provides information you should know before using the product.

About the Board

This product is a PCI bus-supported board designed for extending RS-422A/485 compatible serial

communication functionality on your PC.

The < COM-2PD-PE > has two RS-422A/485-standard serial ports.

The < COM-4PD-PE > has four RS-422A/485-standard serial ports.

Higher noise-resistant models with isolation between channels and between PC and bus line as well as a

surge protection circuit for communication ports. With a 128byte built-in FIFO buffer for transmission

and reception of each channel, the product supports a baud rate of up to 921,600bps. It also comes

with a Windows/Linux driver, which allows boards to be used as OS-standard COM ports.

This product supports CONTEC-defined driver library “API-PAC(W32)” that provide local routines.

Features

- Max. 921,600bps RS-422A/485 Serial Communication

The < COM-2PD-PE > has two RS-422A/485-standard serial ports.

The < COM-4PD-PE > has four RS-422A/485-standard serial ports.

Baud rates from 2 to 921,600bps can be set. When using the bundled “Standard COM Driver

Software” and “Driver library API-PAC(W32)”, baud rates from 15 to 921,600bps can be set.

- Possibly used as Windows, Linux-standard COM ports, using the bundled driver library

Comes with a driver software that allows the boards to be used under Windows / Linux in the same way

as COM ports on the PC. Under Windows, the product supports the OS-standard Win32 API

communication function as well as Visual Basic MSComm. Under Linux, OS-standard tty driver’s

standard-function can be used. In addition, supplies a diagnostic program to confirm hardware

operation and to perform a communication test with equipment.

- Isolation between channels and between PCs, surge protection for all signal lines

The channels are electrically isolated from each other and from the PC.

As isolation is provided between channels as well as isolation of the bus, this prevents electrical noise

between channels as well as between the PC and external circuits. As surge protection is provided on

all signal lines, you can safely use the boards in environments where you are concerned about surges

causing incorrect operation or damage to the PC.

- Max. 16 boards can be installed as configured in the range COM1 - COM256.

Up to 16 boards can be mounted on a single PC.

COM1 - COM256 can be set using the device manager.

COM-2PD-PE, COM-4PD-PE

5

1. Before Using the Product

- Each channel is equipped with separate 128-byte FIFO buffers for transmit and receive.

Employed a buffer memory 128-byte dedicated to transmission and 128-byte for each channel.

These are FIFO format, useful for high speed communications and to reduce the load to the CPU when

transmitting/receiving. As the device manager can be used to enable/disable the use of FIFO and set

the FIFO trigger size, this permits operation to be adjusted to achiere optinal performance for your

system.

- To suit your application, cables and connectors are available as optional.

COM-4PD-PE : Distribution cable for 4channels (PCE37/9PS) is available as optional.

- The control line for RS-422A/485 can be controlled and monitored by software.

The control lines for RTS, CTS, DTR and DSR can be controlled and monitored using an application.

The lines can be controlled or monitored by software from the application.

- Driver library API-PAC(W32) is supported.

API-PAC(W32) is library software based on Win32 API routines (DLL), which provides local routines

specific to CONTEC. You can create high-speed application software taking advantage of the

CONTEC hardware using various programming languages that support Win32 API functions, such as

Visual Basic and Visual C++.

6

COM-2PD-PE, COM-4PD-PE

1. Before Using the Product

Support Software

You should use CONTEC support software according to your purpose and development environment.

Standard COM Driver Software

COM Setup Disk

(Bundled)

The purpose of this software is to allow the CONTEC serial communication boards to be used under Windows or

Linux in the same way as the standard COM ports on the PC. By installing additional boards, you can use COM

ports in the range COM1 - COM256.

The boards can be used for all types of serial communications such as for remote access service (RAS) and

uninterruptible power supply (UPS) applications.

Under Windows, the serial ports can be accessed using the standard Win32 API communication routines (CreateFile( ),

WriteFile( ), ReadFile( ), and SetCommState( ), etc.) The serial ports are also compatible with the Visual Basic

communication control (MSComm). Supports the communication class of .NET Framework 2.0 (SerialPort class).

Under Linux, the serial ports are compatible with the operating system's standard tty driver. The standard routines

including open( ), close( ), read( ), write( ) are supported.

< Operating environment >

OS Windows 8.1, 8, 7, Vista etc..

You can download the updated version from the CONTEC’s Web site (http://www.contec.com/comdrv/). For more

details on the supported OS, applicable language and new information, please visit the CONTEC’s Web site.

CAUTION

The maximum number of COM ports able to be used depends on the configuration of your OS.

This product is not supported Windows Me, 98, 95, NT.

Driver library

API-PAC(W32)

(Available for downloading (free of charge) from the CONTEC web

site.)

API-PAC(W32) is the library software that provides the commands for CONTEC hardware products in

the form of Windows standard Win32 API functions (DLL). It makes it easy to create high-speed

application software taking advantage of the CONTEC hardware using various programming languages

that support Win32 API functions, such as Visual Basic and Visual C/C++.

It can also be used by the installed diagnosis program to check hardware operations.

CONTEC provides download services (at http://www.contec.com/apipac/) to supply the updated drivers

and differential files.

For details, visit the CONTEC’s Web site.

< Operating environment >

OS Windows Vista, XP, Server 2003 etc..

Adaptation language Visual C++ .NET, Visual C# .NET, Visual Basic .NET, Visual C++, Visual Basic,

Delphi, C++Builder, etc..

CAUTION

This library provides local routines that are specific to CONTEC (SioOpen( ), SioWrite( ), SioRead( ),

SioStatus( ), etc.). These are not compatible with the standard Win32 API communication routines (CreateFile( ) and

WriteFile( ), etc.).

This library does not correspond to 64bit OS.

COM-2PD-PE, COM-4PD-PE

7

1. Before Using the Product

This library does not correspond to Multi CPU, such as HyperThread. Please use it by setup of Single CPU.

Cable & Connector (Option)

- COM-4PD-PE

Connection Conversion Cable (37M

→

9M x 4, 250mm) : PCE37/9PS

* Check the CONTEC’s Web site for more information on these options.

8

COM-2PD-PE, COM-4PD-PE

1. Before Using the Product

Customer Support

CONTEC provides the following support services for you to use CONTEC products more efficiently

and comfortably.

Web Site http

Japanese http://www.contec.co.jp/

English http://www.contec.com/

Chinese http://www.contec.com.cn/

Latest product information

CONTEC provides up-to-date information on products.

CONTEC also provides product manuals and various technical documents in the PDF.

Free download

You can download updated driver software and differential files as well as sample programs available in

several languages.

Note! For product information

Contact your retailer if you have any technical question about a CONTEC product or need its price,

delivery time, or estimate information.

Limited Three-Years Warranty

CONTEC Interface boards are warranted by CONTEC CO., LTD. to be free from defects in material

and workmanship for up to three years from the date of purchase by the original purchaser.

Repair will be free of charge only when this device is returned freight prepaid with a copy of the

original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office,

from which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and

original boards. The warranty is not applicable if the device has been tampered with or damaged

through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in

which case repairs will be considered beyond the warranty policy.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please

obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you

purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the

warrantor be liable for any incidental or consequential damages due to such defect or consequences that

arise from inexperienced usage, misuse, or malfunction of this device.

COM-2PD-PE, COM-4PD-PE

9

1. Before Using the Product

Safety Precautions

Understand the following definitions and precautions to use the product safely.

Safety Information

This document provides safety information using the following symbols to prevent accidents resulting

in injury or death and the destruction of equipment and resources. Understand the meanings of these

labels to operate the equipment safely.

DA

NGE

R

DANGER indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury or in property damage.

10

COM-2PD-PE, COM-4PD-PE

1. Before Using the Product

Handling Precautions

DA

N

GE

R

Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in

an explosion, fire, electric shock, or failure.

CAUTION

- There are switches or jumper on the board that need to be set in advance. Be sure to check these

before installing the board.

- Only set the switches and jumpers on the board to the specified settings.

Otherwise, the board may malfunction, overheat, or cause a failure.

- Do not strike or bend the board. Doing so could damage the board.

Otherwise, the board may malfunction, overheat, cause a failure or breakage.

- Do not touch the board's metal plated terminals (edge connector) with your hands.

Otherwise, the board may malfunction, overheat, or cause a failure.

If the terminals are touched by someone's hands, clean the terminals with industrial alcohol.

- Do not install or remove the board to or from the slot while the computer's power is turned on.

Otherwise, the board may malfunction, overheat, or cause a failure.

Be sure that the personal computer or the I/O expansion unit power is turned off.

- Make sure that your PC or expansion unit can supply ample power to all the boards installed.

Insufficiently energized boards could malfunction, overheat, or cause a failure.

- The specifications of this product are subject to change without notice for enhancement and quality

improvement.

Even when using the product continuously, be sure to read the manual and understand the contents.

- Do not modify the product. CONTEC will bear no responsibility for any problems, etc., resulting

from modifying this product.

- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever

(including damages for loss of business profits) arising out of the use or inability to use this

CONTEC product or the information contained herein.

COM-2PD-PE, COM-4PD-PE

11

1. Before Using the Product

Environment

Use this product in the following environment. If used in an unauthorized environment, the board may

overheat, malfunction, or cause a failure.

Operating temperature

0 - 50°C

Operating humidity

10 - 90%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

Inspection

Inspect the product periodically as follows to use it safely.

Storage

When storing this product, keep it in its original packing form.

(1) Put the board in the storage bag.

(2) Wrap it in the packing material, then put it in the box.

(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,

vibration, magnetism, and static electricity

Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

12

COM-2PD-PE, COM-4PD-PE

2. Setup

2.

Setup

This chapter explains how to set up the board.

What is Setup?

Setup means a series of steps to take before the product can be used.

Different steps are required for software and hardware.

The setup procedure varies with the OS and applications used.

Using the Board under Windows

Using the Standard COM Driver Software COM Setup Disk

This section describes the setup procedure to be performed before you can start developing application

programs for the board using the bundled CD-ROM “Standard COM Driver Software -

COM Setup Disk”.

Taking the following steps sets up the software and hardware. You can use the diagnosis program later

to check whether the software and hardware function normally.

Step 1 Setting the Hardware

Step 2 Installing the Hardware

Step 3 Initializing the Software

On the CD-ROM, refer to the \PCI\Readmee.txt file and the installation instructions files for each OS

located in the \PCI\InstDoc.

If Setup fails to be performed normally, see the “Setup Troubleshooting” section at the end of this

chapter.

Using the Board under Windows

Using the Driver Library API-PAC(W32)

Refer to the API-PAC(W32) "Hardware Installation Procedure (HWINSTU.CHM)" help file for the

procedure to follow when using API-SIO in the "Driver Library API-PAC(W32)".

If using API-SIO from API-PAC(W32), install from API-PAC(W32) instead of from the supplied

CD-ROM.

See also the following parts of this manual as required.

This chapter Step 1 Setting the Hardware

COM-2PD-PE, COM-4PD-PE

13

2. Setup

Using the Board under Linux

Using the Standard COM Driver Software COM Setup Disk

You can perform application program development using the "Standard COM Driver Software -

COM Setup Disk" in the supplied CD-ROM. The procedure for using the software is described in the

\Linux\Readmee.htm file.

See also the following parts of this manual as required.

This chapter Step 1 Setting the Hardware

Operating Systems Other than Windows or Linux

Refer to the following if using on an OS other than Windows or Linux.

This chapter Step 1 Setting the Hardware

Chapter 4 Functions

Chapter 6 About Hardware

14

COM-2PD-PE, COM-4PD-PE

2. Setup

Step 1 Setting the Hardware

This section describes how to set the board and plug it on your PC.

The board has some switches and jumper to be preset.

Check the on-board switches and jumpers before plugging the board into an expansion slot.

The board can be set up even with the factory defaults untouched. You can change board settings later.

Parts of the Board and Factory Defaults

Figure 2.2. - Figure 2.3 shows the names of major parts on the board.

Note that the switch setting shown below is the factory default.

COM-2PD-PE

Figure 2.2. Component Locations < COM-2PD-PE >

COM-2PD-PE, COM-4PD-PE

15

2. Setup

COM-4PD-PE

Figure 2.3. Component Locations < COM-4PD-PE >

16

COM-2PD-PE, COM-4PD-PE

2. Setup

Setting the Board ID

If you install two or more boards on one personal computer, assign a different ID value to each of

the boards to distinguish them.

The board IDs can be set from 0 - Fh to identify up to sixteen boards.

If only one board is used, the original factory setting (Board ID = 0) should be used.

Setting Procedure

To set the board ID, use the rotary switch on the board. Turn the SW1 using, for example, a standard

screwdriver, to set the arrow to the board ID.

1

2

3

4

5

6

0

7

9

A

B

C

D

E

F

8

BOARD ID

SW1

(Board ID = 0)

Factory setting:

Figure 2.4. Board ID Settings (SW1)

COM-2PD-PE, COM-4PD-PE

17

2. Setup

Setting Transmission Mode

The data transfer mode setting switch is used to switch between full duplex and half duplex and to

specify whether to use RTS/CTS in full duplex mode. Set the appropriate data transfer mode for the

device with which you are communicating. SW3 sets the mode for channel 1, SW5 for channel 2,

SW7 for channel 3, and SW9 for channel 4. Bits 1 - 5 are used to set the data transfer mode. Always

set bit 6 is to OFF.

Setting Procedure

Table 2.1. Setting Transmission Mode

CAUTION

Do not use with bits 1 and 2 both set ON as this may result in damage to the board.

18

COM-2PD-PE, COM-4PD-PE

2. Setup

Setting of Terminator

The terminator setting switch controls whether or not a terminator is inserted into each signal line. Set

the terminators on or off in accordance with the devices with which you are communicating. The

terminators on the board are 100

Ω

resistors.

SW2 sets the terminator for channel 1, SW3 for channel 2,

Setting Procedure

If you wish to use a terminator of other than 100

Ω

, set the terminator switch OFF and insert an external

terminator. The diagrams below show examples of terminator installation for half and full duplex setting.

Table 2.2. Setting of Terminator

SW2,

SW4,

SW6,

SW8

Not inserted

1

3

2 4

ON

RTS

TxD

CTS

RxD

Factory

setting

- Falf-duplex

Terminator

(Bit 3)

(A)

(D)(C)

(B)

1

3

2 4

ON

RTS

TxD

CTS

RxD

[B or C]

SW2,

SW4,

SW6,

SW8

1

3

2 4

O

N

RTS

TxD

CTS

RxD

1

3

2 4

ON

RTS

TxD

CTS

RxD

Insert the

terminator

[A or D]

SW2,

SW4,

SW6,

SW8

Terminator

(Bit 3)

Not insert the

terminator

Not insert the

terminator

Figure 2.5. Multi Drop Connection

COM-2PD-PE, COM-4PD-PE

19

Page is loading ...

Contec COM-4PD-PE Owner's manual

This manual is also suitable for

Contec COM-4PD-PE Owner's manual

Related papers

Other documents