1 DTP-4C
Screw Terminal
DTP-4C User’s Guide
CONTEC CO.,LTD.
Thank you for purchasing the CONTEC product.
The DTP-4C is a screw terminal fastened with screws, which relays the I/O wirings of CONTEC
interface board/card or card with a 37-pin D-SUB connector.
The pins in the 37-pin D-SUB connector correspond to their respective terminals on the terminal strips
on a one-to-one basis, allowing you to easily connect the board/card to an external device via the
terminal strips.
Note: To connect a board/card to the accessory, you need the separately priced option cable.
Features
- A signal line from an external device can be connected to the terminal simply by using screws.
- The optional cable can be used to connect easily to the board/card.
Product Configuration List
This product is configured as follows. Be sure you have received all of the components listed. If any
components are missing or broken, contact the store where you purchased this product.
- Body…1 - User’s Guide (this document)…1
- Warranty Certificate …1 - Serial number label …1
CAUTION
The option cable is not appended to the interface board/card and this product. Cable differs
according to board/card used. Be sure to check the manual or visit the CONTEC’s Web site to
buy an appropriate one.
DTP-4C User’s Guide
DTP-4C 2
External View and Dimensions
Figure 1. External View and Dimensions
DTP-4C Connections
Board
or
Card
Product
Exlernal
device
Option cable
Signal line from external device
29
28
27
26
25
24
23
22
21
20
N.C.
N.C.
37
36
35
34
33
32
31
30
N.C.
19
18
17
16
15
14
13
12
11
20
1
CN1
37
19
DTP-4(PC)
10
9
8
7
6
5
4
3
2
1
Figure 2. DTP-4 Connections
(1) Connect the interface board/card and the product using the separately available option cable.
(2) Check the wiring destination of the product and wire the signal conductors from the external device.
You can easily connect the conductors to the terminals using the screws.
DTP-4C User’s Guide
3 DTP-4C
Wiring Diagram
Figure 3. Wiring Diagram
Specifications
Table 1. Specifications
Item Specifications
Terminal
Terminal type JTB552-02-10-3-M10 [mfd by JITE] equivalent
Number of terminals on
terminal strips
37 pin
Stripped length (mm) 6
Screws M2.5
Connectable wire (mm
2
) Maximum connection range : 0.13 - 1.5
Single wires : 0.5 - 1.5
Stranded wires : 0.5 - 1.5
Connector
Connector used 37 pin D-SUB connector [Female]
DC-37ST-N [mfd. by JAE] equivalent
Applicable connector 37 pin D-SUB connector [Male]
DC-37P-N [mfd. by JAE] equivalent
Dimensions (mm) 160(W) x 82(H)
DTP-4C User’s Guide
Copyright 2013 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. February 2013 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ NA00598 (LYLG113)
Chinese http://www.contec.com.cn/ 02152013_rev3 [03012010]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Difference point with DTP-4A
This product is a successor of the previous model DTP-4A. So you can use the same operating
procedures as DTP-4A.
The differences on the specification are as follows :
DTP-4C DTP-4A
Terminal type JTB552-02-10-3-M10
[mfd. by JITE] equivalent
ML-35A-10P
[mfd by Sato Parts] equivalent
Screws M2.5 (cross recessed head) M2.6 (slotted head)
Terminal color Green White
Height of rubber
foot
7.2mm 5.0mm
Cautions
(1) No part of this document may be copied or reproduced in any form by any means without prior
written consent of CONTEC CO., LTD.
(2) The specifications of this product are subject to change without notice for quality improvement.
Even when using the product continuously, be sure to read the manual and understand the contents.
(3) All relevant issues have been considered in the preparation of this document. Should you notice
an omission or any questionable item in this document, please feel free to notify CONTEC CO.,
LTD.
(4) Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or
for any results of using the product.
(5) Brand and product names are trademarks of their respective holder.
(6) The foreign body (the metal piece, the combustible, and liquid, etc.) must not touch the product.
Otherwise, the product may malfunction, overheat or cause a failure.
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec DTP-4A Owner's manual
-
-
-
-
-
-
-
-
-