Wacker Neuson AR 75/1,5/400 User manual

Brand: Wacker Neuson

Model: AR 75/1,5/400

Type: User manual

Operator's manual

External vibrator

AR, ARFU

Model AR, ARFU

Document 5100002209

Issue 11.2019

Version 12

Language en

100_0000_0001.fm 2

Printed in Germany

All rights are reserved, in particular the worldwide applicable copyright, right of duplication and right of

distribution.

This document may only be used by the recipient for the intended purpose. The document may not be

reproduced entirely or partially, or translated into any other language.

Reproduction or translation, even extracts thereof, only with written approval of Wacker Neuson

Produktion GmbH & Co. KG.

Any breach of the statutory regulations, in particular the protection of copyright, will lead to civil and

criminal prosecution.

Wacker Neuson Produktion GmbH & Co. KG is constantly working on the improvement of its products

as part of the technical further development. Therefore, we reserve the right to make changes to the

illustrations and descriptions in this documentation without incurring any obligation to make changes to

machines already delivered.

Errors excepted.

The machine on the cover may have special equipment (options).

Manufacturer

Wacker Neuson Produktion GmbH & Co. KG

Wackerstraße 6

D-85084 Reichertshofen

www.wackerneuson.com

Tel.: +4984533403200

E-Mail: [email protected]

Original operator's manual

100_0000_0001.fm

1 CALIFORNIA Proposition 65 Warning

100_0000_0024.fm 4

1 CALIFORNIA Proposition 65 Warning

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Diesel engine exhaust and some of its constituents are known to the State of

California to cause cancer, birth defects, and other reproductive harm.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead

compounds, and other chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

5 5100002209IVZ.fm

1 CALIFORNIA Proposition 65 Warning .................................................................................4

2 Preface ...................................................................................................................................7

3 Introduction ...........................................................................................................................8

3.1 Using the manual......................................................................................................................... 8

3.2 Storage location of the manual.................................................................................................... 8

3.3 Accident prevention regulations................................................................................................... 8

3.4 More information.......................................................................................................................... 8

3.5 Target group................................................................................................................................ 8

3.6 Explanation of symbols................................................................................................................ 8

3.7 Wacker Neuson Contact partner ................................................................................................. 9

3.8 Disclaimer.................................................................................................................................... 9

3.9 Product identification of the machine........................................................................................... 9

4 Safety ....................................................................................................................................10

4.1 Principle..................................................................................................................................... 10

4.2 Proper use................................................................................................................................. 10

4.3 Structural modifications ............................................................................................................. 10

4.4 Operator responsibility............................................................................................................... 10

4.5 Operating company responsibilities........................................................................................... 10

4.6 Personnel qualification............................................................................................................... 11

4.7 Residual dangers....................................................................................................................... 11

4.8 General safety information......................................................................................................... 12

4.9 Electrical safety.......................................................................................................................... 12

4.10 Specific safety information – external vibrators......................................................................... 13

4.11 Safety when using formworks.................................................................................................... 14

4.12 Personal protective gear............................................................................................................ 14

4.13 Safety devices ........................................................................................................................... 15

4.14 Safeguarding against switching back on ................................................................................... 15

4.15 How to act in dangerous situations............................................................................................ 15

5 Safety and information labels ............................................................................................16

6 Structure and function ........................................................................................................17

6.1 Standard package...................................................................................................................... 17

6.2 Field of application..................................................................................................................... 17

6.3 Brief description......................................................................................................................... 17

6.4 Variants...................................................................................................................................... 17

7 Components and operator's controls ...............................................................................18

7.1 AR.............................................................................................................................................. 18

7.2 ARFU......................................................................................................................................... 19

8 Transport and storage ........................................................................................................20

8.1 Safety......................................................................................................................................... 20

8.2 Transport preparation................................................................................................................ 20

8.3 Transporting the machine.......................................................................................................... 20

8.4 Storage...................................................................................................................................... 20

9 Installation ...........................................................................................................................21

9.1 Safety......................................................................................................................................... 21

9.2 Before installation...................................................................................................................... 21

10 Use and operation ...............................................................................................................24

10.1 Safety......................................................................................................................................... 24

10.2 Prior to starting the machine...................................................................................................... 24

10.3 Fitting the machine .................................................................................................................... 24

10.4 Electrical connection.................................................................................................................. 26

10.5 Switching on the machine.......................................................................................................... 26

Inhalt

5100002209IVZ.fm 6

10.6 Switching off the machine.......................................................................................................... 27

10.7 Activities after use...................................................................................................................... 27

11 Maintenance .........................................................................................................................28

11.1 Safety ........................................................................................................................................ 28

11.2 Maintenance personnel qualifications........................................................................................ 28

11.3 Maintenance schedule............................................................................................................... 28

11.4 Cleaning the machine................................................................................................................ 29

11.5 Lubricate machine ..................................................................................................................... 29

12 Troubleshooting ..................................................................................................................30

12.1 Safety ........................................................................................................................................ 30

12.2 Table – malfunctions.................................................................................................................. 30

12.3 Bodyguard

®................................................................................................................................................................ 30

12.4 Inverter ...................................................................................................................................... 31

13 Disposal ................................................................................................................................32

13.1 Disposal of old electrical and electronic equipment................................................................... 32

14 Accessories .........................................................................................................................33

14.1 Fastening clamps....................................................................................................................... 33

15 Technical data ......................................................................................................................34

15.1 AR26.......................................................................................................................................... 34

16 Technical data ......................................................................................................................37

16.1 AR34.......................................................................................................................................... 37

17 Technical data ......................................................................................................................40

17.1 AR43.......................................................................................................................................... 40

18 Technical data ......................................................................................................................42

18.1 AR52.......................................................................................................................................... 42

18.2 AR53.......................................................................................................................................... 43

18.3 AR54.......................................................................................................................................... 45

19 Technical data ......................................................................................................................48

19.1 AR63.......................................................................................................................................... 48

19.2 AR64.......................................................................................................................................... 49

20 Technical data ......................................................................................................................52

20.1 AR75.......................................................................................................................................... 52

21 Technical data ......................................................................................................................56

21.1 ARFU26..................................................................................................................................... 56

EC declaration of conformity

.....................................................................................59

DIN EN ISO 9001 Zertifikat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

2 Preface

7 100_0000_0002.fm

2 Preface

This operator's manual contains important information and procedures for the safe, proper and economic

operation of this Wacker Neuson machine. Carefully reading, understanding and observing is an aid to

avoiding hazards, repair costs and downtime, and therefore to increasing the availability and service life

of the machine.

This operator's manual is not a manual for extensive maintenance or repair work. Such work should be

carried out by Wacker Neuson service or by technically trained personnel. The Wacker Neuson machine

should be operated and maintained in accordance with this operator's manual. An improper operation or

improper maintenance can pose dangers. Therefore, the operator's manual should be constantly

available at the location of the machine.

Defective machine parts must be exchanged immediately!

If you have any questions concerning the operation or maintenance, a Wacker Neuson contact person

is always available.

3 Introduction

100_0000_0013.fm 8

3 Introduction

3.1 Using the manual

This manual is to be considered part of the machine and should be carefully stored during the entire

service life of the machine. This manual shall be transferred to subsequent owners or users of the

machine.

3.2 Storage location of the manual

This manual is part of the machine and must be kept in the immediate vicinity of the machine and made

accessible to staff at all times.

If this manual is lost, or if a second copy is required, there are two options to obtain a replacement:

 Download from the Internet: www.wackerneuson.com

 Contact your Wacker Neuson contact partner.

3.3 Accident prevention regulations

In addition to the notes and safety instructions in this manual, the local accident prevention regulations

as well as the national health and safety regulations apply.

3.4 More information

This manual applies to various machine types from one product series. For this reason, some figures

may vary slightly in appearance from the machine purchased. Depending on the model, there may be

descriptions of components that are not included in the standard package.

The information contained in this manual is based on machines manufactured up to the time of printing.

Wacker Neuson reserves the right to change this information.

The manufacturer shall immediately include any modifications or additions in this manual.

3.5 Target group

Individuals working with this machine must be regularly trained on the dangers of handling the machine.

This manual is intended for the following people:

Operating personnel:

These individuals have been trained on the machine and informed about the possible dangers in the

event of improper conduct.

Technically trained personnel:

These people have professional training as well as additional knowledge and experience. They are able

to assess the tasks assigned to them and recognize possible dangers.

3.6 Explanation of symbols

This manual contains specially emphasized safety instructions in the following categories: DANGER,

WARNING, CAUTION and NOTICE.

Before performing any work on or with this machine, the notes and safety instructions must be read and

understood. All notes and safety instructions in this manual must be passed on to the maintenance,

repair, and transport personnel.

DANGER

This combination of symbol and signal word indicates a hazardous situation that will lead

to death or serious injury if it is not avoided.

WARNING

This combination of symbol and signal word indicates a hazardous situation that can lead

to death or serious injury if it is not avoided.

CAUTION

This combination of symbol and signal word indicates a hazardous situation that can lead

to minor injury or damage to the machine if it is not avoided.

3 Introduction

9 100_0000_0013.fm

3.7 Wacker Neuson Contact partner

Depending on the country, the Wacker Neuson contact partner is a Wacker Neuson service department,

a Wacker Neuson subsidiary, or a Wacker Neuson dealer.

On the Internet at www.wackerneuson.com.

3.8 Disclaimer

For the following violations, Wacker Neuson dismisses any liability for personal injury or material

damage:

 Failure to follow this manual.

 Unintended use.

 Deployment of untrained personnel.

 Using non-approved spare parts and accessories.

 Improper handling.

 Structural modifications of any kind.

 Failure to observe the "General Terms and Conditions" (GT&Cs).

3.9 Product identification of the machine

Data of the type label

The type label contains information that uniquely identifies this machine. This information is required for

ordering spare parts and when inquiring about technical issues.

 Enter information about the machine in the following table:

NOTICE

Supplementary information.

Designation Your information

Group and model

Year of manufacture

Machine number

Version no.

Item no.

4 Safety

100_0102_si_0003.fm 10

4 Safety

4.1 Principle

State of the art

This machine has been constructed with state-of-the-art technology according to the recognized rules of

safety. However, improper use can pose a risk to life and limb of the user and/or third parties, or cause

damage to the machine and other equipment.

4.2 Proper use

This machine, depending on its type, can be used only for the excitation of all types of molds and

formworks, vibratory tables, vibratory stands, compaction of fresh concrete and for mounting on

conveyor belts (silo).

Other special applications must be checked and released by Wacker Neuson.

Proper use also includes the observance of all notes and safety information contained in this manual, as

well as complying with the prescribed service and maintenance instructions.

Any other use is regarded as improper.

Any damage resulting from improper use will void the warranty and the liability on behalf of the

manufacturer. The operator assumes full responsibility.

Misuse particularly applies to:

 Immersing the machine in fresh concrete.

 Using the machine and the components of this machine as climbing aids.

 Failure to observe instructions for vibratory tables, frequency converters, etc.

4.3 Structural modifications

Structural modifications must not be undertaken without the written consent of the manufacturer.

Structural changes without the consent of the manufacturer can pose a risk to users and/or third parties,

and also damage the machine.

The manufacturer's liability and warranty will also cease in the event of unauthorized structural

modifications.

Especially the following are cases of structural modifications:

 Opening the machine and the permanent removal of components.

 Installing components that do not originate from Wacker Neuson and are not equivalent in terms of

design and quality to the original components.

 The addition of any type of accessory that does not originate from Wacker Neuson.

Spare parts or accessories that originate from Wacker Neuson can be safely mounted. They can be

found on the Internet under www.wackerneuson.com.

4.4 Operator responsibility

The operator is the person who operates this machine for commercial or economic purposes, or who

hands it over for use/application by a third party, and who bears legal product responsibility during

operation for the protection of staff or third parties.

The operating company must make the manual available to staff at any time and ensure that operatives

have read and understood the manual.

4.5 Operating company responsibilities

 Know and implement applicable occupational safety provisions.

 Investigate dangers in a risk assessment based on working conditions at the site.

 Produce operating instructions for this machine.

 Regularly check that the operating instructions are up-to-date with the latest guidelines.

 Clearly regulate and specify responsibilities for installation, use, troubleshooting, maintenance and

cleaning.

NOTE

Notes and safety information in this chapter apply to all machine types described in this

manual.

4 Safety

11 100_0102_si_0003.fm

 Train staff at regular intervals and inform them about potential hazards.

 Provide staff with the required protective gear.

4.6 Personnel qualification

This machine may only be operated and used by trained staff.

Incorrect application, misuse or use by untrained staff threaten the health of the users and/or third parties

and risk damaging the machine or causing a failure.

The following requirements also apply to the user:

 Physically and mentally fit.

 Reactions not impeded by drugs, alcohol or medication.

 Familiarity with the safety information in this manual.

 Familiarity with correct operation of this machine.

 The minimum age to use the machine has been reached.

 Instructed in how to operate the machine independently.

4.7 Residual dangers

The following section lists dangers based on the risk assessment. Residual risks are particular risks

associated with handling machinery which, despite compliance with the standards of safe construction,

cannot be eliminated.

Residual risks are not obviously recognizable and can be the source of a potential injury or risk to health.

 If unforeseeable residual risks occur, the machine must be switched off immediately and the

competent manager informed. The manager will make further decisions and do everything necessary

to eliminate the risk.

 The manufacturer of the machine must be informed if necessary.

DANGER

Risk of fatal injury from electrical voltage!

There is an immediate danger to life from touching live parts. Damaged insulation or

individual parts can be dangerous to life.

Therefore:

 If the insulation is damaged, immediately disconnect the power supply and arrange

repair work.

 Only allow qualified electricians to perform work on the electrical system.

 The electrical system must be disconnected from the mains power and tested to

ensure no voltage.

 The power supply must be switched off before maintenance, cleaning and repair work

and fused before being switched on again.

 Do not bypass fuses or decommission. Use the correct number of amps when

changing fuses.

 Protect live parts from wet conditions. Danger due to short circuit.

WARNING

Noise-induced hearing damage!

Noise in the area where work is performed can cause serious hearing damage.

Therefore:

 Suitable ear protection must be worn during all work that generates noise.

 Only remain in the danger zone for as long as is necessary.

WARNING

Heat-induced risk of burning!

The machine can become extremely hot during long use and cause burns on contact with

skin. Therefore:

 Allow the machine to cool down after use.

 If the cooling down stage cannot be complied with (e.g. in an emergency), always wear

heat-resistant gloves.

4 Safety

100_0102_si_0003.fm 12

4.8 General safety information

The safety information in this chapter contain the "General Safety Information", which must be listed in

the manual in accordance with applicable standards. Information may be included that does not apply to

this machine.

4.8.1 Safety in the workplace

 Keep work space tidy. Untidy or unlit work spaces can lead to accidents.

 Working with this machine in an explosive environment is forbidden. Electrical tools produce sparks,

which can ignite dust or vapor.

 Keep children and other persons away from work performed on this machine. Distraction while using

the machine can cause loss of control.

 Working with this machine among dry vegetation is forbidden. Danger of fire!

 Always secure the machine against tipping over, rolling, sliding, and falling. Danger of injury!

4.8.2 Service

 Machine must only be repaired or maintained by qualified specialist staff.

 Only use original replacement parts and accessories. This ensures that the operational safety of the

machine is maintained.

4.8.3 Safety of people

 Working under the influence of drugs, alcohol or medication can lead to serious injuries.

 Suitable protective gear must be worn for all work. Suitable protective gear significantly minimizes the

risk of injury.

 Ensure that the machine is switched off before connecting to a power source. Unintended setup can

lead to serious injuries.

 Remove tools before starting up the machine. A tool left on a moving part could be hurled out and

lead to serious injuries.

 Always ensure your position is safe.

 Wear suitable clothing. Keep loose or baggy clothing, gloves, jewelry, and long hair away from

moving or rotating parts. Risk of entanglement!

4.8.4 Handling and use

 Do not exceed the operating limits of the machine or allow it to operate for longer periods. Risk of

damage to the machine.

 Never start up machines with defective switches. Replace defective switches immediately. Machines

with defective switches conceal a high risk of injury.

 Avoid unintended machine startup. Remove plug from plug receptacle before making adjustments to

the machine settings. Unintended startup can lead to serious injuries.

 Keep unused machines out of reach of children. Machine may only be used by trained staff.

 Handle machine with care. Replace defective parts immediately before starting up this machine.

Defective machines conceal a high accident risk.

 Use the machine, accessories, tools, etc., in accordance with these instructions.

4.9 Electrical safety

The safety information in this chapter contain the "General Safety Informations", which must be listed in

the manual in accordance with applicable standards. Information may be included that does not apply to

this machine.

NOTE

All notes and safety information in this manual must be read and complied with. Failure to

comply with these instructions can result in electric shock, fire and/or serious injuries,

damage to the machine, and/or damage to other objects. Keep safety information and

notes for future reference.

NOTE

All notes and safety information in this manual must be read and complied with. Failure to

comply with these instructions can result in electric shock, fire and/or serious injuries,

damage to the machine, and/or damage to other objects. Keep safety information and

notes for future reference.

4 Safety

13 100_0102_si_0003.fm

 Machine connector plug must fit plug receptacle. Connector plug must not be altered in any way. Do

not use adapter plugs with grounded machines. Unaltered plugs and plug receptacles minimize the

risk of electric shock.

 Avoid body contact with grounded surfaces. There is an increased risk of electric shock if the body is

grounded.

 Keep machine away from wet conditions. Penetrating moisture increases the risk of electric shock.

 Do not use cables other than for their intended purpose. Protect cables from heat, oil, and sharp

objects. Damaged or tangled cables increase the risk of electric shock.

 When working outdoors, only use cables suitable for outdoor spaces. Using a cable for outdoor

spaces minimizes the risk of electric shock.

 A fault current protective switch must be used if working in a damp environment cannot be avoided.

Fault current protective switches minimize the risk of electric shock.

 Safety devices, switches, or easily damaged parts must be checked to ensure that they are

functioning perfectly and according to regulations before this machine is used. Defective safety

devices conceal a high risk of injury and must be replaced immediately by specialist staff.

4.9.1 Electric power supply for electrical appliances of protection class I+III

This machine must be in perfect condition before it is connected to an electric power supply. The

following parts must be particularly checked for damage before use.

 Plug.

 Entire length of power cable.

 Power cable.

One of the following safety devices must be present when connecting to local or mobile power

generators:

 Transformer with safe separation.

 Motor generator with equally separated windings.

4.9.2 Extension cable and cable drum

Compliance with the following points is required to minimize the risk of injury, fire, electric shock, and

material damage:

 Extension cables and cable drums must be checked and undamaged.

 Only use extension cables with grounded conductor and grounded conductor connection on plug and

coupling.

 Only use extension cables and cable drums that are tested and suitable for use on the construction

site.

 Damaged extension cables and cable drums must not be used and must be replaced immediately.

 Cable drums and multiple plug sockets must display the same requirements as extension cables.

 Protect extension cables, cable drums, multiple plug sockets and connection couplings from wet

conditions.

 Extension cables and cable drums must be fully unwound before startup.

4.10 Specific safety information – external vibrators

4.10.1 Operating safety

 Only use this machine for the specified applications.

 Never leave machine running unattended – Risk of injury!

NOTE

The rated voltage is located on the nameplate of this machine.

Observe relevant national safety regulations!

NOTE

All notes and safety information in this manual must be read and complied with. Failure to

comply with these instructions can result in electric shock, fire and/or serious injuries,

damage to the machine, and/or damage to other objects. Keep safety information and

notes for future reference.

4 Safety

100_0102_si_0003.fm 14

 Use a wide area to separate off work space and keep out unauthorized persons – Risk of injury!

 Users of this machine must ensure that persons who have to remain in the work space keep to a

minimum distance of 15 meters from the machine while in operation.

 Personal protective gear must be worn during all work on and with this machine.

 If the machine is not used, it must be put away.

 Store machine accordingly.

4.11 Safety when using formworks

4.11.1 Use stable formwork

Only use stable molds and formworks to attach the external vibrator.

Molds and formworks which have not been properly hardened or which are too loosely connected can

overload the machine or be damaged themselves.

Ensure that the formwork is suitable for attaching external vibrators.

The following points must be observed:

 Sufficient possibilities for attaching.

 Formwork sufficiently stable for attaching the variant of external vibrator used (depending on

performance of the external vibrator).

4.11.2 Formwork and safety belt

If an external vibrator is used in conjunction with fastening clamps, the fastening clamp must always be

attached with a safety belt (Wacker Neuson accessory) to the formwork – Risk of falling!

The following points must be observed:

 Securely attach the safety belt to the formwork above the external vibrator.

 Safety belt must be attached so that it is taut.

4.12 Personal protective gear

NOTE

All notes and safety information in this manual must be read and complied with. Failure to

comply with these instructions can result in electric shock, fire and/or serious injuries,

damage to the machine, and/or damage to other objects. Keep safety information and

notes for future reference.

NOTE

To avoid injuries wherever possible while handling the machine, personal protective gear

must be worn when working on or with this machine.

Pictogram Meaning Description

Use ear protection! Protects against permanent hearing damage.

Wear a hard hat! Hard hats protect against head injuries from falling parts.

Wear safety shoes! Safety shoes shoes protect feet from being crushed,

from falling parts, and from sliding on slippery floors.

Wear protective gloves! Protective gloves protect hands against abrasions,

puncture wounds, and contact with hot surfaces.

4 Safety

15 100_0102_si_0003.fm

4.13 Safety devices

Safety devices protect the user of a product from exposure to existing risks. These safety devices are

barriers (protective guards) or other technical measures. These prevent the user being exposed to a risk,

or, in certain situations, eliminate or reduce the source of risk.

The ARFU has the following safety equipment:

Bodyguard®

The Bodyguard® acts to protect the operator from electric shock.

4.14 Safeguarding against switching back on

Compliance with the following steps is required to ensure that the machine is safeguarded

against unauthorized or uncontrolled switching on:

1. Switch off machine at ON/OFF switch (if there is one).

2. Switch off power or fuel supply.

3. Remove plug from power generator.

4.15 How to act in dangerous situations

Preventive measures:

 Always be prepared for accidents.

 Keep first aid kit (first aid box, blankets, etc.) within easy reach.

 Familiarize staff with accident reporting, first aid, and rescue facilities.

 Keep access roads clear for the emergency services.

 Train staff in first aid.

What to do in an emergency:

 Immediately switch off the machine (e.g. remove mains plug from plug receptacle).

 Get the injured and any other people away from the danger zone.

 Commence first aid.

 Call doctor and/or fire department.

 Clear access roads for the emergency services.

 Inform managers at the site.

WARNING

Risk of injury due to missing or non-operational safety devices.

 Only operate the machine with properly installed and functioning safety devices.

 Do not modify or remove safety devices.

NOTE

Always operate this machine with a protective motor switch!

Item Description

1 Bodyguard®

DANGER

Danger to life from unauthorized or uncontrolled switching back on. Unauthorized or

uncontrolled switching back on can lead to serious injuries or death.

 Switch off machine at the ON/OFF switch.

 Disconnect machine from the electric power supply.

 Before switching back on, ensure that all safety devices are mounted and functional.

5 Safety and information labels

100_0102_ls_0002.fm 16

5 Safety and information labels

The following stickers are located on the machine:

WARNUNG

Illegible symbols.

Over time stickers and signs on the machine can become dirty or otherwise unclear.

 Ensure that all safety and warning notices and operating instructions on the machine

are in a legible condition.

 Replace damaged stickers and signs immediately.

Label Description

Warning of hot surface.

Read the operator's manual before start-up.

US-machine Caution.

 Warning! Risk of electrocution.

 Do not open housing.

 Read the operator's manual.

US-machine Warning.

From chemicals that cause cancer, birth defects or other reproductive

damage.

0219173

CAUTION

VORSICHT

ATENCIÓN

ATTENTION

0219262

0219413

0219261

WARNING

WARNUNG

ADVERTENCIA

ADVERTISSEMENT

0219176

6 Structure and function

17 100_0102_sf_0002.fm

6 Structure and function

6.1 Standard package

The standard package includes:

 External vibrator

 Operator's manual

6.2 Field of application

External vibrators are generally used when space for using an internal vibrator is restricted. External

vibrators are also suitable for attaching to all types of vibratory tables and vibratory stands.

Specific variants of this machine can even be mounted on conveyor belts (e.g. on silos).

6.3 Brief description

The external vibrator is a construction machine for concrete processing which deals with the compaction

of liquid concrete. For this purpose, the external vibrator is firmly attached to a formwork and transfers

vibrations from there into the concrete.

Inside the external vibrator is an electric motor, which helps drive an eccentric weight. Different

centrifugal forces can be set by adjusting the balance of the eccentric weights or the number of eccentric

discs.

Concrete has to be compacted to eliminate the air inclusions in fresh concrete. This is how concrete gets

its solidity.

The eccentric discs must be symmetrically mounted to avoid damage to formworks.

Bodyguard

The Bodyguard® connects the mains supply line with the converter and monitors the operating currents

flowing in and out. The Bodyguard® helps protect the operator from electric shock in case of failure

(leakage currents).

The indicator light illuminates in red when the machine is closed correctly and the machine functions

correctly.

The indicator light doesn't illuminate when a leakage current occurred inside the machine.In this case,

the mains side power supply is cut off and the converter locked. The machine does not operate. The

power supply remains cut off until the error is remedied.

The Bodyguard® features a test button to check the function of the Bodyguards®.

The machine only works in connection with the Bodyguard®.Inverter

The inverter comprises a current rectifier and a d.c.-a.c. converter monitored by an electronic control.

The current rectifier converts the input voltage (AC single phase) to DC voltage.

The d.c.-a.c. converter converts the generated DC voltage to three phase current (AC three phase).

When the machine is switched on, the control electronics provides a soft start and thus prevents critical

starting currents.

6.4 Variants

Several variants were specified in the technical data for the machine types:

Alternating current

Cable switch

3,5kN

Max. centrifugal force set

Variably adjustable voltage from … through

7 Components and operator's controls

100_0102_cp_0002.fm 18

7 Components and operator's controls

7.1 AR

AR26 AR34

AR43 AR52

AR53 AR54

AR63 AR64

AR75

7 Components and operator's controls

19 100_0102_cp_0002.fm

7.2 ARFU

Item Description Item Description

1 Motor case 7 Screwed-on saddle clamp

2 Hood 8 Tapered zerk fitting

3 Terminal box 9 Power cable (optional)

4 Cable gland 10 ON/OFF switch (optional)

5 Typenschild 11 Plug (optional)

6 Nameplate 12 Control lamp (optional)

ARFU26

Item Description Item Description

1 Motor case 8 Inverter

2 Hood 9 Control lamp

3 Terminal box 10 ON/OFF switch

4 Cable gland 11 Bodyguard

5 Power cable 12 Control lamp

6 Plug 13 Test button

7 Control lamp (optional) 14 Nameplate

8 Transport and storage

100_0102_tr_0002.fm 20

8 Transport and storage

8.1 Safety

8.2 Transport preparation

Compliance with the following steps is required before the machine is transported:

1. Switch off machine at the ON/OFF switch.

2. Wait until the machine has come to a complete standstill.

3. Disconnect the machine from the electric power supply.

4. Let the machine cool off. Risk of burns!

5. Unscrew machine from formwork or undo from fastening clamp.

8.3 Transporting the machine

Compliance with the following points is required wherever possible to avoid serious injuries or

damage to the machine:

 Place machine in a suitable container for transport (e.g. wire mesh collapsible).

 Wind up power cable – do not bend power cable.

 Secure machine against falling, tipping, and rolling away.

 Do not use leads, cables, or safety belts as transport handles.

 Do not use leads, cables, or safety belts to secure for transport.

 Do not lift machine directly with a crane – use suitable container for transport (e.g. wire mesh

collapsible).

8.4 Storage

The following points must be observed to avoid possible damage to the machine:

 Do not store outside.

 Store in a dry and dust-free place.

 Do not expose to aggressive substances.

 Avoid mechanical vibrations.

 Oil the places that are prone to rust.

WARNING

Incorrect transport

Risk of injury and damage to the machine from incorrect transport.

 Perform all steps in accordance with the specifications of this manual.

 Observe notes when transporting machine.

 Use personal protective gear.

NOTE

If the machine does not have an ON/OFF switch, it can be switched off using the inverter

ON/OFF switch.

Page is loading ...

Wacker Neuson AR 75/1,5/400 User manual

Wacker Neuson AR 75/1,5/400 User manual

Wacker Neuson AR 75/1,5/400 User manual

Related papers

Other documents