VONN Lighting VMW12460AL Installation guide

Brand
VONN Lighting
Model
VMW12460AL
Type
Installation guide

This manual is also suitable for

VONN Lighting VMW12460AL is a versatile and energy-efficient LED fixture designed to provide ample lighting for your indoor spaces. With its sleek and modern design, it seamlessly blends with various décor styles. Installation requires attention to safety measures, including turning off the electricity at the main fuse box and using a qualified electrician for the job. The fixture should be installed on its own independent circuit and is compatible with ELV (Electric Low Voltage) type dimmers.

VONN Lighting VMW12460AL is a versatile and energy-efficient LED fixture designed to provide ample lighting for your indoor spaces. With its sleek and modern design, it seamlessly blends with various décor styles. Installation requires attention to safety measures, including turning off the electricity at the main fuse box and using a qualified electrician for the job. The fixture should be installed on its own independent circuit and is compatible with ELV (Electric Low Voltage) type dimmers.

© VONN Lighting,2017
Installation Guide
ON
VONN Lighting
Model:
VMW12460
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
PHILLIPS
LADDER
DRILL
SCREW DRIVER
Parts List
A.
B.
C.
D.
E.
A
B
C
D
E
Circuit Box
Mounting Plate (Part of the Fixture)
Anchor Screws x 8
Wire Connectors x 3
Ground Screw x 1
Plastic Anchors x 8
Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact VONN Lighting
Customer Service at 888-604-8666 for a replacement.
Please read and comprehend the entire manual before attempting to
assemble, operate, or install the product.
VONN highly recommends to use a qualified, licensed electrician to install
the fixture.
VONN recommends to install the fixture on its own independent circuit.
Do not install the fixture on the same circuit with other appliances, or
HVAC systems.
LED INFO & WARNINGS
•
•
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
Place the wall switch in the “OFF” position of the room you are installing
the fixture.
•
Shut “OFF” the electricity at main fuse box.
•
VONN recommends ELV (Electric Low Voltage) type dimmers for this
fixture.
•
•
Do not remove or replace VONN manufactured driver that is provided
with the fixture.
x 2
© VONN Lighting,2017
WALL
Fixture Diagram
Mounting
Plate
A
Plastic
Anchor
B
Ground
Screw
E
Wire Connector
D
Anchor
Screw
C
WALL
Mounting
Plate
A
Step 1. Connect Wires
© VONN Lighting,2017
Supply Wires:
Ground Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire)
from outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral
Wire) from outlet box.
Connect Bare Copper (Ground Wire) from fixture to Green
or Bare Copper (Ground Wire) from outlet box.
Twist wires together clockwise and secure with wire
connector (C).
Installer Tip (1): If ground wire is not available in outlet box,
then secure Bare Copper (Ground Wire) from fixture to
ground screw (D) on mounting plate (A).
Installer Tip (2): Supply wires can be either tucked into
outlet box or fixture canopy.
Wire Connector
D
Ground
Screw
E
White
(Neutral Wire)
Black
(Line Wire)
Bare Copper
(Ground Wire)
© VONN Lighting,2017
WALL
Mounting
Plate
A
Plastic
Anchor
B
Anchor
Screw
C
Step 2. Install Mounting Plate
Raise mounting plate (A) to wall. Mark location for the
plastic anchors (B). Use drill to drill holes for plastic anchors
(B). Insert plastic anchors (B) into hole.
Screw anchor screws (C) into plastic anchors (B) to secure
canopy cover (A).
© VONN Lighting,2017
WALL
Mounting
Plate
A
Step 3. Mount Fixture
Attach canopy cover to mounting plate (A). Attach
decorative covers to fixture.
Canopy Cover
Decorative
Covers
© VONN Lighting,2017
Step 4. Turn Power ON
Turn electricity “ON” at main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the fixture.
ON
ON
Circuit Box
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

VONN Lighting VMW12460AL Installation guide

Brand
VONN Lighting
Model
VMW12460AL
Type
Installation guide
This manual is also suitable for

VONN Lighting VMW12460AL is a versatile and energy-efficient LED fixture designed to provide ample lighting for your indoor spaces. With its sleek and modern design, it seamlessly blends with various décor styles. Installation requires attention to safety measures, including turning off the electricity at the main fuse box and using a qualified electrician for the job. The fixture should be installed on its own independent circuit and is compatible with ELV (Electric Low Voltage) type dimmers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents