Weil-McLain SB0203 User manual

Weil-McLain
Brand
Weil-McLain
Model
SB0203
Type
User manual

Weil-McLain SB0203 is a device that can be used to prevent thermal shock in water boiler installations with three-way valves. It works by using a by-pass piping arrangement to ensure that cold system water is not returned to a hot boiler. The SB0203 can be used with single or multiple boilers and is easy to install and maintain.

Weil-McLain SB0203 is a device that can be used to prevent thermal shock in water boiler installations with three-way valves. It works by using a by-pass piping arrangement to ensure that cold system water is not returned to a hot boiler. The SB0203 can be used with single or multiple boilers and is easy to install and maintain.

Subject: Water Boiler Installations with Three-Way Valves
Number: SB0203 (Page 1 of 2)
Date: November 22, 2002
Primary/Secondary pumping is the preferred method for system temperature modulation in
commercial hydronic heating installations. Three-way valves are also used on many
installations for this purpose. Without proper system design and control, three-way valves
can cause cold system water to be returned to a hot boiler. This condition could lead to
boiler thermal shock, creating a potential for section failure. With minimal equipment
investment, thermal shock conditions can be reduced on three-way valve installations.
Weil-McLain makes the following design recommendations.
Piping Selection
:
1. Use by-pass piping arrangement – See Figure 1 or 2.
2. Follow basic boiler piping instructions in the boiler manual.
Three-Way Valve Selection
:
1. Use valves with minimum timing of four minutes from one extreme position to the other.
2. Size to circuit design requirements. Follow manufacturer’s recommendations. Normally
valve will be one or two pipe sizes smaller than recommended boiler piping size.
3. Avoid oversizing to prevent poor control of mixed water.
4. Pressure drop across the valve should be high enough to provide accurate control
without “hunting”.
Circulator Selection
:
1. Size system circulator to circuit flow characteristics. Specify gpm and head requirements.
2. Size each by-pass circulator as follows:
1 .
# of boilers used
[1/4 to 1/3 flow (gpm) of system circulator] X
3. All circulators must run at the same time.
EXAMPLE: Specify equipment to by-pass one 1,000,000 btuh Weil-McLain boiler.
Piping: (1) tee, (1) ell, (1) 45° tee (By-pass size and length will vary on each installation.)
Circulator:
1,000,000 btuh .
10,000 btuh
System flow rate with 20° ∆T through boiler = = 100 gpm
1 .
1 boiler
By-pass flow rate = 1/4 X 100 gpm X
= 25 gpm
In most cases a standard booster pump can provide the necessary flow at by-pass gpm and
head requirements.
www.weil-mclain.com.
Technical Services Bulletin No: SB0203 (Page 2 of 2)
Subject: Water Boiler Installations with Three-Way Valves
Date: November 22, 2002
BOILER
SYSTEM
TO
P1
VALVE
3-WAY
PUMP
10 TO 20
PIPE
AT LEAST
DIAMETERS
P2
PUMP
FROM SYSTEM
Figure 1
By-Pass Piping Using Three-Way Valve – Single Boiler
10 TO 20
AT LEAST
DIAMETERS
3-WAY
VALVE
SYSTEM
TO
P1
BOILER
PUMP
P2
PIPE
PUMP
P3
BOILER
PUMP
AT LEAST
10 TO 20
DIAMETERS
PIPE
FROM SYSTEM
Figure 2
By-Pass Piping Using Three-Way Valve – Multiple Boilers
  • Page 1 1
  • Page 2 2

Weil-McLain SB0203 User manual

Weil-McLain
Brand
Weil-McLain
Model
SB0203
Type
User manual

Weil-McLain SB0203 is a device that can be used to prevent thermal shock in water boiler installations with three-way valves. It works by using a by-pass piping arrangement to ensure that cold system water is not returned to a hot boiler. The SB0203 can be used with single or multiple boilers and is easy to install and maintain.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents