Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
www.ohlins.com
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To find the latest information contact
your Öhlins distributor. Please
consult your Öhlins dealer if you
have any questions regarding the
contents in this document.
Shock Absorber for ATV Yamaha Raptor 700 R - Rear
YA 972
Mounting Instructions
Part No. Pcs.
Shock absorber YA972 1
C-spanner 00710-02 1
Öhlins Sticker 00197-01 2
Memo Notes Sticker 01180-01 1
Owner’s Manual ATV 07235-01 1
Before installing this product, check the
contents of the kit. If anything is missing, please
contact your nearest Öhlins dealer.
Kit Contents
Free Sag and Ride Height
Adjustments
Please note that during storage and
transportation, especially at high ambient
temperature, some of the oil and grease used for
assembling may leak and stain the packaging.
This is in no way detrimental to the product,
wipe off the excessive oil/grease with a cloth.
Part no. YA972_0
Issued 2009-06-01
Warning!
Before installing this product, read the Öhlins
Owner’s Manual. The shock absorber is an
important part of your vehicle and will affect the
stability.
Warning!
Before riding, always make sure that the
basic settings made by Öhlins are according
to recommended Set-up Data. Read about
adjustments and setting up in the Öhlins
Owner’s Manual before you make any
adjustments. Contact an Öhlins dealer if you
have any questions about setting up the shock
absorber.
Rebound Damping
Adjuster
Compression
Damping
Adjuster
Free sag and Ride height
Free sag, front 60 ± 5 mm (2½ ± ¼ “)
Free sag, rear 30 ± 5 mm (1 ¼ ± ¼ “)
Ride height, front 80 ± 5 mm (3 ¼ ± ¼ “)
Ride height, rear 105 ± 5 mm (4½ ± ¼ “)
Rebound damping 15 clicks
Compression damping 10 clicks
Spring pre-load 5 mm
Shock absorber length 380 mm
Stroke 123 mm
Set-up Data
Spring Preload
Adjuster
1 2
Adjust Spring How to install
Warning!
It is advisable to have an Öhlins dealer install the
shock absorber.
When installing, read the Vehicle Service
Manual.
1
Remove the seat.
2
Raise the rear end of the vehicle so that the
original shock absorber is in an unloaded
position.
Warning!
Make sure the vehicle is securely supported so
that it will not fall over.
3
Remove the original shock absorber.
Note!
Remove the lower bolt of the triangle link so that
the lower bolt of the shock absorber can be
removed.
Remove
bolt
Fold out
the arm
Triangle link
Lower shock
absorber
bolt
!
4
Install the Öhlins shock absorber in the same
position as the original unit. Fasten the upper
attachment rst.
Note!
The piggy back reservoir should be at the top,
towards the rear and slightly to the left.
5
Fasten the lower attachment. Raise the
wheels slightly to make the attachment t.
Reattach the triangle link!
6
Tighten the attachment screws to the correct
torque. Consult your ATV Owners manual.
7
Check sag and ride height according to the
Öhlins Owner’s manual. See also Set-up data
in this manual.
Note!
Make sure that all bolts are tightened to the
correct torque and that nothing fouls or restricts
movement of the shock absorber when the
suspension is being fully compressed or
extended.
A
Spring
platform
clamp
Spring
platform
Spring Preload = A - B
A Free spring length
B Installed spring length
A
B
1
Measure the free length of the spring (A).
2
Loosen the screw on the spring platform
clamp so that you can move the spring
platform as far up as needed to install the
spring.
3
Put the shock absorber up-side-down in a
vice so that you can install the spring and the
spring clip.
Note!
The spring platform and spring are press fitted.
Push hard to install the spring.
4
Measure the spring length. Adjust the spring
preload to the recommended setting, see
section Set-up data in this folder.
5
Install the shock absorber to the vehicle
according to the procedure in this folder.
Check sag and ride height (see Owner’s
Manual) and adjust spring preload again if
necessary.
Note!
Tighten the screw on the spring platform clamp
before riding the motorcycle.
1
2
3
Spring
Spring clip
1
2
3
4
5
3
Spring Guide
Rider’s Weight Spring Spring Rate
75 kg/ 165 lbs Standard swingarm 00698-11 54 N/mm
85 kg/ 187 lbs Standard swingarm 00698-12 56 N/mm
95 kg/ 209 lbs Standard swingarm 00698-13 58 N/mm
4
/