Messoa NCR366 User manual

Brand: Messoa

Model: NCR366

Category: Security cameras

Type: User manual

User

Manual

201608 366 A1

IR Bullet Network Camera

NCR366

Table of Contents

1 Product Overview 4

1.1 Physical Characteristics 4

2 Installation 6

2.1 Package Content 6

2.2 Installation 6

2.2.1 Checking Appearance 6

2.2.2 Mounting & Wiring 7

2.2.3 Safety Wire Preparation 9

2.2.4 Adjusting the Camera Position 10

2.2.5 Adjusting the Protection Shield Hood 11

3 Connection 12

3.1 Network Topology 12

3.2 System Requirements 12

3.3 Connecting Process 13

3.3.1 Default IP address 13

3.3.2 Connecting from a computer & Viewing Preparation 13

3.4 IP Finder 17

4 Administration and Conguration 18

4.1 Live View 18

4.2 Conguration 20

4.2.1 Encode 20

4.2.2 Image 23

4.2.3 Lens Control 28

4.2.4 Video 29

4.2.5 Network 32

4.2.6 System 44

4.2.7 Account 48

4.2.8 Event Source 51

4.2.9 Video Analytics 61

4.2.10 Event Setting 72

Appendix: Specications of IR Bullet Network Camera 78

WARNING

●

This camera operates at DC 12V / PoE (IEEE 802.3af Class 3) only.

●

Installation and service should be performed only by qualied and experienced technicians and comply with all local

codes and rules to maintain your warranty.

●

To reduce the risk of re or electric shock, do not expose the product to rain or moisture.

●

Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry

soft cloth.

●

Do not apply benzene or thinner to the camera, which may cause the surface to be melted or lens fogged.

●

Avoid aligning the lens with extremely bright objects (e.g., light xtures) for long periods of time.

●

Although this camera is waterproof and suitable for both indoor and outdoor usages, please do not sink the camera into

water. Contact your dealer in case of sunk.

●

Avoid operating or storing the camera in the following locations:

• Extremely humid, dusty, or hot/cold environments (recommended operating temperature: -40°C to +50°C)

• Close to sources of powerful radio or TV transmitters

• Close to uorescent lamps or objects with reections

• Under unstable or ickering light sources

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the

European Union and other European countries with separate collection systems). This product should be

disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

FCC Compliance Statement

Information to the user: This unit has been tested and found to comply with the limits for a Class B

digital device pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation.

If this unit does cause harmful interference to radio or television reception, which can be determined by turning the unit o

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

●

Reorient or relocate the receiving antenna.

●

Increase the separation between the unit and receiver.

●

Connect the unit to an outlet on a circuit dierent from that to which the receiver is connected.

●

Consult the dealer or an experienced radio/TV technician for help.

CE Statement

Operation is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired

operation. The manufacturer declares that the unit supplied with this guide is compliant with the essential

protection requirements of EMC directive and General Product Safety Directive GPSD conforming to

requirements of standards EN55022 for emission, EN 55024 for immunity, EN 300 and EN 328 for WIFI.

Caution

Changes or modications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the unit.

1 Product Overview

1.1 Physical Characteristics

203

128

Unit: mm

Figure 1 - 1: Physical Dimension & Pictorial Index

Table 1 - 1: Pictorial Index Denition

No. Name Description

1 RJ-45 Ethernet / PoE Port

Insert an Ethernet cable into the port for network connection as well as PoE (Power

over Ethernet) capability.

2 DC 12V Port

To power on the camera via DC12V power source. Pay attention to the polarities

when connecting to DV12V power supply.

3 Protection Shield Hood To minimize the eects from rain and sunlight on image quality.

4 Mounting Bracket

For mounting the camera onto different environments, the mounting bracket is

designed with 2 axes for exible adjustment.

5 Internal Interface Cover

Use a cross screwdriver to loosen the 2 screws and open the cover so that the

internal interfaces including “RESET”, “DEFAULT” button, “Micro SD Card Slot”, etc.,

will be shown. More details are described as the following gure and table.

Figure 1 - 2: Internal Interface Pictorial Index

No Interface Description

A Mini USB Port

Connect with USB to RJ-45 adaptor for real time image preview, which is useful for

installer to adjust a desired eld of view during installation.

B LED Indicators

Green It symbolizes the camera is powered on.

Orange It symbolizes the camera is inserted with a micro SD card.

Blue & Red It symbolizes network data has been under transmission.

C Micro SD card slot Insert a micro SD card into the slot for recording and le storage.

D Reset & Default Button

Press the button for 6 seconds to restore to the factory default settings.

Press the button for below 1 second to reboot the camera.

E Technical Debug Port This is a spared port for technician to execute specic operations if needed.

Table 1 - 2: Internal Interface Denition

2 Installation

2.1 Package Content

2.2 Installation

Check if everything in the packing box matches to the order form and the packing slip. All items listed below should be

included in the packing box.

•

Network IR Bullet Camera * 1

•

Printed Quick Guide * 1

•

Guide Pattern * 1

•

Plastic Anchors * 3

•

Tapping Screws * 3

Please contact your dealer if any of the items is lost.

Following tools might help you complete the installation:

•

a drill

•

screwdrivers

•

wire cutters

2.2.1 Checking Appearance

When rst unboxing, please check whether if there is any visible damage to appearance of the camera and its accessories.

The protective materials used for the packaging should be able to protect the camera from most of accidents during

transportation. Please remove the protective materials of the camera when every item is properly checked in accordance

with the list in “Package Content”.

2.2.2 Mounting & Wiring

Step 1. Mounting Preparation

•

Use the guide pattern to mark out and prepare a mounting area.

1. Place the supplied guide pattern on a mounting surface. Drill 6 mm (0.25”) outer holes x 3 at the mounting surface

corresponding to the 3 indicated positions for plastic anchors.

2. Please then hammer the 3 plastic anchors into the 3 drilled holes on the mounting surface.

This section is the preserved

area for cable entry space.

Figure 2 - 1: Guide Pattern

Step 2. Mounting the Camera

1. Position the camera to match the 3 holes embedded with the plastic anchors on the surface.

2. Secure the 3 tapping screws to fasten the camera with the mounting surface tightly.

Plastic Anchors

Tapping Screws

Figure 2 - 2: Mounting the Camera

Step 3. Wiring the Camera

1. While mounting the camera, pass the PoE Port and DV12V Port cable, which penetrates from the mounting bracket,

through the hole of mounting surface or place it by the side hole of the mounting bracket as the following figures

shown depending on your dierent applications.

2. Connect an Ethernet cable terminated with the RJ-45 connector with the PoE Port of the camera and make sure the

other end of the Ethernet cable connects with a PoE compatible network device that supplies power with networking

capability. Also, connect DC12V power source wires to the DC12V port if necessary. Pay attention to the polarities when

connecting wires to the DV12V port.

DC 12V Port

Ethernet Cable with

RJ-45 Connector

PoE Port

Figure 2 - 3: Connecting the Wires Type

Ⅰ

- Bracket Side Hole

Figure 2 - 4: Connecting the Wires Type

Ⅱ

– Mounting Surface Holde

2.2.3 Safety Wire Preparation

If you possess a safety wire (fall prevention wire, not supplied), connect the safety wire with one end to the mounting surface

and the other end to the safety-cord screw of the camera.

Safety wire

Safety-cord screw of the camera

Figure 2 - 5: Mounting the Camera

Warning

Depending on the material of mounting surface, different screws and anchors than those supplied

may be required. To prevent the camera from falling o, ensure that it is mounted to a rm place using

a safety wire strong enough to withstand the total weight of the camera. (Pay also attention to the

nishing at the end of the wire.)

Caution

Safety wire must be connected with one end to the surface and the other end to the safety-cord screw of

the camera. By cabling so, it is possible to prevent the camera from accidental falling at any time.

2.2.4 Adjusting the Camera Position

•

Pan Adjustment (A)

Rotate the A joint to adjust the camera horizontally for applying to a variety of applications.

•

Tilt Adjustment (B)

Tilt the B joint to adjust the camera vertically for applying to varied applications.

•

Locking Ring (C)

By rotating the C ring counter-clockwise, the pan & tilt joints will be loosened and able to be adjusted for dierent

angles; on the other hand, rotating the C ring clockwise will fasten the pan & tilt joints altogether.

Figure 2 - 6: Adjusting the Camera Position

Caution

Limitation for Two axes position:

•

Pan range : ±360°

•

Tilt range : 0°

90°

Note After adjustments, make sure to tighten the each joint for preventing camera from removing.

2.2.5 Adjusting the Protection Shield Hood

This camera is designed with capability to operate under rugged environments and thus will possibly be subject to inuences

from sunlight or rain. Protection shield hood is consequently coated on the camera to prevent from those outside eects. To

adjust the protection shield hood, rst loose the 2 cross screws above the hood followed by moving the protection shield

hood forward or backward till a desired position based on your need of dierent applications.

Figure 2 - 7: Adjusting the Protection Shield Hood

Caution

•

Be sure to adjust the protection shield hood in accordance with the lens coverage in case of shadow

problems occurring.

•

To avoid housing damage, DO NOT adjust the protection shield hood position excessively.

3.1 Network Topology

The camera, which is equipped with Ethernet RJ-45 network interface, can deliver live view image in real time via both

Internet and Intranet manners. Please refer to the skeleton drawings shown below for understanding.

Figure 3 - 1: Network Topology

3 Connection

Below table lists the minimum requirement to implement and operate the camera. No hardware/software component

inferior to the requirements is recommended.

Table 3 - 1: System Requirements

System Hardware

CPU Intel Pentium 4 2.4GHz or equivalent

RAM 1 GB or above

Display NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500

System Software

Operating System Microsoft Windows XP, Windows Vista, Windows 7 or above

Browser Microsoft Internet Explorer 8 ~ 10, Chrome, Firefox, Safari

Unit

Power Supply DC 12V / PoE (IEEE 802.3af Class 3)

Networking

Wired* 10/100BASE-T Ethernet (RJ-45 connector)

*A switch is required for surveillance on multiple cameras.

Note All the installation and operations should comply with your local electricity safety rules.

Caution

When adopting PoE, this camera is to be connecting only to PoE networks without routing to

heterogeneous devices.

3.2 System Requirements

3.3.1 Default IP address

Since this is a network-based unit, an IP address must be assigned at the very first. The unit’s default IP address is

192.168.1.30 and sub mask is 255.255.255.0. However, if you have a DHCP server in your network, the unit would obtain

an IP address automatically from the DHCP server so that you don’t need to change the camera’s IP address. But be sure to

enable DHCP in "Network Settings".

3.3.2 Connecting from a computer & Viewing Preparation

Connecting from a computer

1. Make sure the unit and your computer are in the same subnet.

2. Check whether if the networking available between the unit and the computer by executing ping the default IP address.

To do this, simply start a command prompt (Windows: from the Start Menu, select Program. Then select Accessories

and choose Command Prompt.), and type “Ping 192.168.1.30”. If the message “Reply from…” appears, it means the

connection is available.

3. Start a browser e.g. Internet Explorer and enter IP address: 192.168.1.30. A login window should pop up. In the window,

enter the default user name: admin, password: 1234 and select a user interface language to log in.

Further administration on the unit can be found in “4. Administration and Conguration".

Figure 3 - 2: Login Window

3.3 Connecting Process

Viewing Preparation

Images of the unit can be viewed through Microsoft Internet Explorer 8 or above. Before viewing, follow these steps to

enable the display.

1. Enable Cookies as instructions below



In Internet Explorer, click Internet Options on the Tools menu.



On the Privacy tab, move the settings slider to Low or Accept All Cookies.



Click OK.

2. When a proxy server is used, click Internet Options on the Tools menus of Internet Explorer, select Connect tab, click

LAN button, and set proxy server.

3. Change Security in Internet options as instructions below



On tool menu, click Internet Option.



Press the Security tab.



If the camera operates inside of the intranet, click the Intranet icon.



If the camera operates outside of the intranet, click the Internet icon.



Click Custom Level. This will open the Security Settings – Internet Zone screen.

Figure 3 - 3: Security Settings 1/4



Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:

【

Download signed ActiveX controls

】



Prompt (recommended)

【

Download unsigned ActiveX controls

】



Prompt

【

Initialize and script ActiveX not marked as safe for scripting

】



Prompt

Figure 3 - 4: Security Settings 2/4

【

Automatic prompting for ActiveX controls

】



Enable

Figure 3 - 5: Security Settings 3/4

【

Run ActiveX controls and plug-ins

】



Enable

【

Script ActiveX controls marked safe for scripting*

】



Enable

Figure 3 - 6: Security Settings 4/4



Press OK to save the settings.



Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking eect.



Type your setting IP address into the browser.



Then you should be able to see the camera image screen.

IP Finder is a utility program that helps users to locate the unit in local area network that computer is connected to. Please

note that IP Finder works only in Microsoft Windows XP, Microsoft Windows Vista, and Microsoft Windows 7 or above. Steps to

get the utility program running are listed below.

1. Download IP Finder from MESSOA Website to the computer.

2. Double click on IPFinder.exe in the IP Finder folder, and the IP Finder window should pop out.

3. The window would list information of units in operation at present. Press FIND CAMERA to nd more units.

4. Locate and double-click one of the cameras in the list you want to congure the network settings. If you have multiple

cameras connected to your local network, locate the MAC address on the camera to distinguish the target camera from

others.

5. Congure the following settings as needed.

• NAME: Enter a descriptive name for the camera.

• NETWORK SETTINGS: If you have a DHCP server on your network to assign IP addresses to network devices, enable

the DHCP option. Otherwise, manually enter the IP ADDRESS, NET MASK and GATEWAY values.

• USERNAME & PASSWORD: Manually setup preferred username and password.

• SET: Whenever you make revision of camera settings, click “SET” to take effect.

• SW DEFAULT: To perform the factory defaults excluding network settings of the selected camera.

• HW DEFAULT: To perform the factory defaults of the selected camera.

• REBOOT: To reboot the selected camera.

Click Save to enable the settings and click Exit to exit the utility.

Figure 3 - 7: IP Camera Finder

3.4 IP Finder

4 Administration and Conguration

4.1 Live View

Figure 4 - 1: First Login Page

After accessing and login to the IP address of camera, the screen will be shown as the screenshot above. There’re 2 main

options on the upper left side: “Live View” and “Conguration”. The upper right corner, on the other hand, indicates the

current user level and the “Logout” option allows user, by clicking, to log out. In addition, the dropdown menu beside the

Conguration is for UI language switch. We mainly focus on Live View part in this chapter and will detail Conguration in the

“3.2 Conguration” chapter later.

Figure 4 - 2: Live View

After clicking “Live View”, user will be led to a real-time live view image. The “Stream1, 2, 3” are available for user to switch

among each stream conguration for better adaptation in varied applications, for which you may refer to the latter chapter

“3.2.1 Encode” for details. And the other appeared dropdown menu above live view image is for VA performances display on

live view, for which you may refer to “3.2.9 Video Analytics” for more detailed settings; while the “Enable Object Detection”

check box is invented for activating moving objects detection under each VA function, the performance by which will be,

when enabled, a blue frame encircles moving object within eld of view to indicate moving object is being subtly sensed by

surveillance camera.

The following icons within the table, which are in the left-side window and on the top of Live View screen, are for several

functions activation and statuses indication. Please refer to the detailed denitions below for more understanding.

Icon Denition

The “Snapshot” button is for taking a snapshot saved in a user-preferred le path.

The “Full Screen” button is for users to display a full screen live view display. (Press Esc to

back)

The “Manual Recording” button is for users to activate recording function.

The icon on the upper-right corner indicates live view video is being recorded.

The “Zoom Control” button, which is limited for only MBL030A-ORZ0310 Series models,

is for users to manipulate zoom magnication. Place the mouse cursor over the live view

scree followed by using the scroll wheel to perform zoom in or zoom out.

The adjustable bar of “Live View Jitter Buer Length” is for user to dene a value by the

unit of millisecond (ms) ranging from 0 to 1000 in order to lessen the negative video delay

effect raised from network issues, e.g. unstable connection, thus striking a balance to

compromise between real-time and smooth image quality.

Table 4 - 1: Live View Icon Denition - 1

Note Keep the zoom level of applied browser as 100% to display a normal live view.

Page is loading ...

Messoa NCR366 User manual

Brand: Messoa

Model: NCR366

Category: Security cameras

Type: User manual

Download PDF

report

Messoa NCR366 User manual

Messoa NCR366 User manual

Related papers

Other documents