Barska AC12136 Owner's manual

Brand: Barska

Model: AC12136

Type: Owner's manual

Side View

Angled View

Multi Reticle Electro Sight with Red Laser

Parts of the Multi Reticle Electro Sight

1. Objective Lens

2. Battery Compartment and Cap

3. Rheostat Knob and Reticle Color Selector

4. Integrated Weaver Picatinny Rails

5. Locking Nuts

6. Windage Adjustment

7. Elevation Adjustment

8. Reticle Selector Knob

Parts of the Red Laser

9. Laser Aperture

10. Windage Adjustment

11. Elevation Adjustment

12. Push Button On/Off Battery Cap

WARNING: BE CERTAIN THAT YOUR FIREARM IS

NOT LOADED AND POINTED AWAY FROM YOU IN

A SAFE DIRECTION

ATTENTION: THIS BARSKA LASER SIGHT IS A

POWERFUL TARGETING DEVICE THAT

REQUIRES SPECIAL ATTENTION WHEN

OPERATING. CAREFULLY READ THE FOLLOWING

INSTRUCTIONS AND SAFETY PRECAUTIONS

BEFORE USING THIS PRODUCT.

CAUTION: UNAUTHORIZED USE MODIFICATIONS

OF ADJUSTMENTS OR PERFORMANCE OF

PROCEDURE OTHER THAN SPECIFIED HEREIN

MAY RESULT IN DANGEROUS/HAZARDOUS

RADIATION EXPOSURE.

LASER LIGHT: AVOID DIRECT EYE EXPOSURE.

WARNING KEEP OUT OF REACH OF CHILDREN.

DO NOT POINT LASER AT PEOPLE, PETS,

SHINY/HIGHLY REFLECTIVE SURFACES, AIRPLANES OR ANY OTHER

OBJECT NOT INTENDED FOR DESIGNATED USE.

ALL DISCHARGING OF FIREARMS SHOULD BE DONE AT AN

APPROVED RANGE OR EQUALLY SAFE AREA. USE OF EYE AND EAR

PROTECTION IS RECOMMENDED.

DIRECT VIEWING OF THE SUN CAN CAUSE PERMANENT EYE

DAMAGE. DO NOT ATTEMPT TO VIEW THE SUN DIRECTLY WITH

EITHER THIS PRODUCT OR THE NAKED EYE.

Red and Green

IR Multi Reticle

ELECTRO SIGHT

Installing the Battery

To install battery, unscrew the battery compartment and insert one CR2032

3V Lithium battery positive ("+") side up. Replace the battery cover. If the

reticle dims or does not illuminate at all, replace with one CR2032 3V

Lithium battery.

Mounting

Position the electro sight so that the objective lens is facing the same

direction as the muzzle of the firearm. With an allen wrench loosen each of

the locking nuts. Align the integrated weaver picatinny mounting base of the

electro sight onto the rail of the firearm, and slide electro sight into place.

Tighten each of the locking nuts to secure in place.

Windage and Elevation

You can find the windage on the left side of the sight. This adjusts the

horizontal axis of the sight. The elevation is located on the top of the sight.

This adjusts the vertical axis of the sight.

Windage

Turn the screw counter clockwise to make the reticle move to the right. Turn

the screw clockwise to make the reticle move to the left.

Elevation

Turn the screw counter clockwise to raise the reticle. Turn the screw

clockwise to lower the reticle.

Zeroing In

Select the reticle pattern you desire by turning the reticle selector knob. Use

the rheostat knob and reticle color selector for the best intensity.

With the electro sight mounted, rest the gun on a solid support. Sight along

the barrel and aim at a target 50 to 100 yards away. Sight through the

electro sight and use the windage and elevation adjustments to align the

illuminated reticle with the target as seen along the barrel. Click value 1/2” at

50 yards. Each click adjustment moves the point of impact by 1 MOA

(approx. 1” @ 100yds. Or 1/2” @ 50yds.)

LASER

Installing the Batteries

To install batteries, unscrew the cap of the laser insert three AG10 batteries

positive ("+") end facing out. Replace the battery cap. If the laser dims or

does not illuminate at all, replace the batteries. Only use three AG10

batteries.

NOTE: Do not mix old and new batteries.

Do not mix different types of batteries such as alkaline, standard

(carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.).

Windage and Elevation

You can find the windage on the side of the laser. The windage is located at

a 45° angle on the laser. This adjusts the horizontal axis of the sight. The

elevation is located on the top of the laser. This adjusts the vertical axis of

the sight.

Windage

Turn the screw counter clockwise to make the laser dot move to the right.

Turn the screw clockwise to make the laser dot move to the left.

Elevation

Turn the screw counter clockwise to raise the laser dot. Turn the screw

clockwise to lower the laser dot.

Zeroing In

1. The push button to activate the laser is located on the rear of the laser,

push button to activate the laser and push button again to de-activate

the laser.

2. With the laser on, from a bench rest position, fire three shots at the center

of the target.

3. Observe where the pellets or bullets strike the target. Keeping the laser

dot pointing at the center of the target and using the windage and

elevation adjustment screws located in the laser body, move the laser dot

to the center of the group formed by the three shots previously fired. Fire

three more shots and note the points of impact on the target. Make

additional adjustment of the laser as necessary.

Attaching The Pressure Switch Cord

Unscrew the cap on the tail end of the laser and while keeping the batteries

in, attach the pressure switch to the laser.

| Pomona, CA 91767, USA | www. b ar ska.c o m

5/14 BC290

Objective Lens (mm) Reticle Field of View (ft@100yds/m@100m)

Exit Pupil (mm)

Eye Relief (inch)

Weight (oz.)

Length (inch)

1x 33 Green & Red IR Multi Reticle 47.4/15.8 na Unlimited 7.2 3.5

Multi Reticle Electro Sight

with Red Laser

Model: AC12136

Made In China

Manufactured on 05/2014

BARSKA Optics

855 Towne Center Drive

Pomona, CA 91767

Barska AC12136 Owner's manual

Barska AC12136 Owner's manual

Barska AC12136 Owner's manual

Related papers

Other documents