Wolf CG152TS Cooktop Installation Guide

Type
Cooktop Installation Guide
Gas Cooktops Installation Guide
GAS COOKTOPS
Contents
3 Gas Cooktops
4 Specications
10 Installation
14 Troubleshooting
Features and specications are subject to change at any
time without notice. Visit wolfappliance.com/specs for the
most up-to-date information.
2
|
Wolf Customer Care 800.222.7820
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
wolfappliance.com
|
3
Product Information
Important product information including the model and
serial number are listed on the product rating plate. The
rating plate is located on the bottom of the cooktop. Refer
to the illustration below.
If service is necessary, contact Wolf factory certied service
with the model and serial number. For the name of the
nearest Wolf factory certied service or for questions
regarding the installation, visit the contact & support section
of our website, wolfappliance.com or call Wolf customer
care at 800-222-7820.
Rating plate location.
RATING PLATE
GAS COOKTOPS
4
|
Wolf Customer Care 800.222.7820
Installation Requirements
A minimum 2" (51) is required from the bottom of the
cooktop to combustible materials. If the cooktop is installed
above an oven, a minimum of
1
/4" (6) is required between
units.
The contemporary gas cooktop can be mounted ush with
the top of the countertop, or as a standard installation
sitting on top of the countertop surface. If the cooktop is
to be mounted ush with the countertop, a recessed area
surrounding the cooktop cut-out must be provided. The
countertop must be able to withstand temperatures up to
300°F
(149°C). Wolf downdraft systems cannot be used with
the contemporary gas cooktop.
IMPORTANT NOTE: For ush installations, do not use the
cooktop as a template to create the countertop opening.
Use the countertop cut-out template or specications pro-
vided. Failure to do so may cause damage.
SPECIFICATIONS
Electrical
Installation must comply with all applicable electrical codes.
Locate the electrical supply as shown in the illustrations
on the following pages. A separate circuit, servicing only
this appliance is required. A ground fault circuit interrupter
(GFCI) is not recommended and may cause interruption of
operation.
ELECTRICAL REQUIREMENTS
Electrical Supply grounded, 120 VAC, 60 Hz
Service 15 amp dedicated circuit
Receptacle 3-prong grounding-type
Power Cord 6'
(1.8 m)
wolfappliance.com
|
5
SPECIFICATIONS
Gas Supply
Installation must conform with local codes or, in the absence
of local codes, with the National Fuel Gas Code.
Locate the gas supply as shown in the illustrations on the
following pages.
The cooktop is equipped for use with natural or liquid
propane (LP) gas. It is design certied by the Canadian
Standards Association (CSA) for natural or LP gases. The
product rating plate has information on the type of gas that
should be used. For rating plate location, refer to the illustra-
tion below. If this information does not agree with the type
of gas available, check with the local gas supplier. The gas
pressure regulator is built into the unit.
GAS REQUIREMENTS
NATURAL GAS WC
Supply Pressure 5" (12.5 mb)
Min Line Pressure 7" (17.5 mb)
Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)
LP GAS WC
Supply Pressure 10" (25 mb)
Min Line Pressure 11" (27.4 mb)
Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)
The cooktop must be connected to a regulated gas supply.
The supply line must be equipped with an approved external
gas shut-off valve located near the cooktop in an accessible
location. Do not block access to the shut-off valve. Refer to
the illustration below.
A gas supply line of
3
/4" (19) rigid pipe must be provided to
the cooktop. If local codes permit, a certied, 3'
(.9 m) long,
1
/2" (13) or
3
/4" (19) ID exible metal appliance connector is
recommended to connect the units
1
/2" NPT male inlet to
the gas supply line. Pipe joint compounds, suitable for use
with natural or LP gas should be used.
The appliance and its shut-off valve must be disconnected
from the gas supply piping system during any pressure
testing of the system at test pressures in excess of .5 psi
(3.5 kPa)
. The appliance must be isolated from the gas
supply piping system by closing its individual manual shut-
off valve during any pressure testing of the system at test
pressures equal to or less than .5 psi
(3.5 kPa).
Wolf natural gas cooktops will function up to 10,250'
(3124 m)
in altitude without adjustment and LP gas cooktops
will function up to 8,600'
(2621 m). If the installation exceeds
these elevations, contact your authorized Wolf dealer for a
high altitude conversion kit.
SHUT-OFF VALVE
OPEN POSITION
GAS SUPPLYTO APPLIANCE
Gas shut-off valve.
Rating plate location.
RATING PLATE
6
|
Wolf Customer Care 800.222.7820
SPECIFICATIONS
FRONT VIEWSIDE VIEW
COUNTERTOP CUT-OUT
NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,
combustible materials cannot be located within this area.
13"
(330)
18"
(457)
7"
(178)
E G
5"
(127)
ELECTRICAL
AND GAS FLOOR
LOCATION
30"
(762)
14"
(356)
19
1
/2"
(495)
2
1
/2" (64)
2
1
/2" (64)
15" Gas Cooktop
STANDARD INSTALLATION
wolfappliance.com
|
7
SPECIFICATIONS
30" | 36" Gas Cooktops (transitional | professional)
STANDARD INSTALLATION
10"
(254)
4" (102)
3
1
/2" (89)
FRONT VIEW
SIDE
VIEW
COUNTERTOP CUT-OUT
NO
TE: Shaded area above countertop indicates minimum clearance to combustible surfaces,
combus
tible materials cannot be located within this area.
El
ectrical and gas supply location only applies to installations with built-in oven.
30"
(762)
W
WIDTH
13"
(330)
18"
(457)
9"
(229)
19
1
/
2
"
(495)
2
1
/2" (64)
2
1
/
2
"
(64)
E G
CUT-OUT WIDTH
W
30" Cooktop 29" (737)
36" Cooktop 35" (889)
8
|
Wolf Customer Care 800.222.7820
SPECIFICATIONS
36" Gas Cooktop (contemporary)
STANDARD INSTALLATION
FRONT VIEW
SIDE
VIEW
NOTE: S
haded area above countertop indicates minimum clearance to combustible surfaces,
combus
tible materials cannot be located within this area.
Ma
ximum facade thickness 1" (25).
30"
(762)
13"
(330)
18"
(457)
9"
(229)
E G
35" (889)
CUT-OUT WIDTH
COUNTERTOP CUT-OUT
20"
(508)
2
1
/2" (64)
5"
(127)
C
L
10"
(254)
1
1
/4" (32)
DIAMETER
4" (102)
C
L
3" (76) MIN–5" (127) MAX
wolfappliance.com
|
9
SPECIFICATIONS
36" Gas Cooktop (contemporary)
FLUSH INSTALLATION
FRONT VIEW
SIDE
VIEW
NOTE:
Shaded area above countertop indicates minimum clearance to combustible surfaces,
combus
tible materials cannot be located within this area.
Ma
ximum facade thickness 1" (25).
Outsid
e corner radius
3
/8" (10).
30"
(762)
13"
(330)
18"
(457)
9"
(229)
E G
36" (914) MIN
RECESS
21"
(533) MIN
RECESS
35"
(889)
CUT-OUT WIDTH
COUNTERTOP CUT-OUT
20"
(508)
2
1
/
2
"
(64)
5
/64"
(
2
)
1
/2"
(13) MAX
COUNTERTOP
PROFILE
5"
(127)
C
L
10"
(254)
1
1
/4" (32)
DIAMETER
4"
(102)
C
L
3" (76) MIN–5" (127) MAX
10
|
Wolf Customer Care 800.222.7820
Transitional | Professional Cooktop
STANDARD INSTALLATION
1 Lower the cooktop into the countertop cut-out. Center
the cooktop in the opening with the front edge aligned
parallel to the front edge of the countertop. Using a
pencil, outline the rear edge of the cooktop on the coun-
tertop. Remove the cooktop.
2 Apply the foam strip to the perimeter of the countertop
opening. Refer to the illustration below. Do not seal the
cooktop to the countertop.
3 Insert the cooktop into the opening, aligning the rear
edge with the pencil line. Verify the cooktop is aligned
with the front edge of the countertop.
4 Attach the brackets provided, to the bottom of the unit.
Insert the 3
1
/2" (89) clamping screws into the brackets.
Use a screwdriver to tighten clamping screws against
the bottom of the countertop. Do not overtighten screws.
Refer to the illustration below.
Cooktop Installation
Remove cooktop and components from the shipping
package and recycle packing materials.
INSTALLATION
FOAM STRIP
COUNTERTOP
BRACKET
CLAMPING
SCREW
Transitional | professional
cooktop.
3 Install bezels to valve assembly by rotating clockwise
until hand tight. Do not overtighten. Refer to the illustra-
tion below.
Contemporary Cooktop
STANDARD INSTALLATION
An optional template has been provided to aid in valve hole
placement.
IMPORTANT NOTE: Prior to installing the cooktop, install
valve stem spacers on valve stem retainers to achieve the
appropriate depth. A 1"
(25) thick facade does not require a
spacer. For all facades less than 1"
(25), subtract the thick-
ness of the facade from 1"
(25) to determine the required
spacer thickness.
1 Once the proper spacing is determined, remove paper
backing from spacers and apply to each valve stem.
Refer to the illustration below.
2 Insert the front of the cooktop into the opening. Slightly
angle the cooktop to align each valve stem with the
holes in the façade. Then lower the back of the cooktop
into position. Refer to the illustration below.
INSTALLATION
SPACER
RETAINER
ALIGN
VALVE STEMS
Apply spacers prior to
installation.
Insert contemporary cooktop.
BEZEL
Install bezels.
wolfappliance.com
|
11
12
|
Wolf Customer Care 800.222.7820
6 Apply a thin lm of petroleum jelly to the outermost,
underside edge of the cooktop pan. The petroleum jelly
aids in future removal.
7 Insert the cooktop into the opening.
8 Ensure the cooktop is fully seated and centered in the
opening.
9 Install bezels to valve assembly by rotating clockwise
until hand tight. Do not overtighten. Refer to the illustra-
tion below.
10 Apply sealant between the cooktop and countertop.
11 Use the squeegee to smooth the seam and remove
excess sealant.
12 Allow the sealant to set for 20 minutes.
13 Use denatured alcohol and paper towels to clean the
seam.
14 Allow 24 hours for the sealant to cure.
15 Use stainless steel cleaner/polish to remove sealant from
the countertop and cooktop.
Contemporary Cooktop
FLUSH INSTALLATION
The following are provided:
A required installation kit
An optional template to aid in cooktop placement
An optional template to aid in valve hole placement
IMPORTANT NOTE: Prior to installing the cooktop, install
valve stem spacers on valve stem retainers to achieve the
appropriate depth. A 1"
(25) thick facade does not require a
spacer. For all facades less than 1"
(25), subtract the thick-
ness of the facade from 1"
(25) to determine the required
spacer thickness.
1 Once the proper spacing is determined, remove paper
backing from spacers and apply to each valve stem.
Refer to the illustration below.
2 Clean all surfaces of dust and debris.
3 Insert the front of the cooktop into the opening. Slightly
angle the cooktop to align each valve stem with the
holes in the façade and lower the back of the cooktop
into position. Refer to the illustration below.
4 Verify there is a gap of at least
1
/16" (2) to the countertop
around the perimeter of the cooktop. The gap allows
for heat expansion. The countertop may be damaged if
there is an insufcient gap.
5 Remove the cooktop.
INSTALLATION
SPACER
RETAINER
ALIGN
VALVE STEMS
Apply spacers prior to
installation.
Insert contemporary cooktop.
BEZEL
Install bezels.
wolfappliance.com
|
13
Gas Supply Connection
All connections to the gas piping must be wrench-tightened.
Do not overtighten or allow pipes to turn when tightening.
If a exible metal connector is being used, verify it is not
kinked, then attach the gas supply line to the regulator on
the cooktop. Open the valve and check for leaks by placing
a liquid detergent solution onto all gas connections. Bubbles
around connections indicate a gas leak. If a leak appears,
close the shut-off valve and adjust connections.
INSTALLATION
14
|
Wolf Customer Care 800.222.7820
Troubleshooting
IMPORTANT NOTE: If the cooktop does not operate prop-
erly, follow these troubleshooting steps:
Verify electrical power is supplied to the cooktop.
Verify the gas supply shut-off valve is in the open
position.
If the cooktop does not operate properly, contact Wolf
factory certied service. Do not attempt to repair the
cooktop. Wolf is not responsible for service required to
correct a faulty installation.
TROUBLESHOOTING
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. Sub-Zero,
Sub-Zero & Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service marks
of Sub-Zero, Inc. All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
WOLF APPLIANCE, INC. P.O. BOX 44848 MADISON, WI 53744 WOLFAPPLIANCE.COM 800.222.7820
9010119 REV-A 6/2016
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Wolf CG152TS Cooktop Installation Guide

Type
Cooktop Installation Guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages