Privileg PCTOC240060F Owner's manual

Brand: Privileg

Model: PCTOC240060F

Category: Hobs

Type: Owner's manual

This manual is also suitable for

DEUTSCH Bedienungsanleitung Seite 4

ENGLISH Instructions for use Page 9

FRANÇAIS Mode d’emploi Page 14

NEDERLANDS Gebruiksaanwijzing Pagina 19

210 mm 160 mm

145 mm 180 mm

GB9

YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT

This manual and the appliance itself provide important safety messages, to be

read and observed at all times.

All safety warnings give specific details of the potential risk present and indicate

how to reduce risk of injury, damage and electric shock resulting from improper

use of the appliance. Please observe the following instructions:

- The appliance must be disconnected from the power supply before carrying

out any installation work.

- Installation and maintenance must be carried out by a qualified technician,

in compliance with the manufacturer’s instructions and local safety

regulations. Do not repair or replace any part of the appliance unless

specifically stated in the user manual.

- Regulations require that the appliance is earthed.

- The electrical components must not be accessible to the user after

installation.

- The appliance is designed solely for household use for cooking food. No

other type of use is allowed (e.g. heating rooms). The Manufacturer declines

all responsibility for inappropriate use or incorrect setting of the controls.

- The appliance is not intended for use by persons (including children) with

any physical, sensory or mental impairment, or without experience and

knowledge of the appliance, unless supervised or previously instructed in

its use by those responsible for their safety.

- The accessible parts of the appliance may become very hot during use. Keep

children away from the appliance and supervise them to ensure that they

do not play with it.

- During and after use, do not touch the heating elements. Do not allow the

appliance to come into contact with cloths or other flammable materials

until all the components have cooled sufficiently.

- Do not place flammable material on or near the appliance.

- Overheated oils and fats catch fire easily. Never leave the appliance

unattended when cooking with fat and oil.

- Do not place metal objects, such as kitchen utensils (knives, forks, spoons,

lids, etc.), on the cooking zone as they can become very hot.

- If the surface of the hob should become damaged (cracked or broken glass),

do not use the appliance and call the After-sales Service immediately.

- The appliance is not intended to be operated by means of an external timer

or separate remote control system.

Use a magnet to check whether pots or pans are suitable for use on the induction

hob: pots are unsuitable if they cannot be magnetically detected.

- Ensure pots have a smooth bottom, otherwise they may scratch the hob’s

glass ceramic surface. Check dishes.

- Do not use empty pots on the hob, especially enamelled or aluminium ones.

This could result in damage to both the glass ceramic surface and the bottom

of the pots.

KEEP THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

This is the safety alert symbol, pertaining to safety, which alerts users

to potential hazards to themselves and others.

All safety warnings are preceded by the danger symbol and the

following terms:

DANGER

Indicates a hazardous situation which, if

not avoided, will cause serious injury.

WARNING

Indicates a hazardous situation which, if

not avoided, could cause serious injury.

BEFORE USE

IMPORTANT: the induction cooking zones will not switch on if

pots and pans are not of the correct dimensions. Only use pots

bearing the symbol “INDUCTION SYSTEM” (See figure opposite).

Before switching the hob on, position the pot on the desired

cooking zone.

EXISTING POTS AND PANS

RECOMMENDED DIAMETERS OF POT

BOTTOMS

NOOK

26 cm

21 cm

17 cm

14 cm

26 cm

21 cm

18 cm

14.5 cm

16 cm

9 cm

18 cm

14.5 cm

16 cm

12 cm

ENGLISH Instructions for use Page

GB10

The manufacturer declines all liability for injury to persons or animals and for

damage to property resulting from failure to observe the regulations provided in

this chapter.

IMPORTANT:

• electrical connection must be made before connecting the oven to the

electricity supply;

• the appliance must be earthed;

• for electrical connection, refer exclusively to the instructions given in the

following paragraph, ignoring the connections indicated on the underside

of the hob.

Connecting the cable to

the terminal block

1. Remove the terminal block screws and the jumpers.

2. Connect the wires to the terminal block as shown in the wiring diagram

below.

3. Secure the cable with the cable clamp next to the protective black sheath.

4. Remove the terminal block cover (A), undoing the screw and inserting the

cover in the terminal block hinge (B). Close the cover (C) and screw it on the

terminal block.

Connection to the oven

• Before connecting the oven to the power supply, make sure that the

cooktop is among the ones listed in the cooktop/oven pairing product sheet

provided.

• Connect the hob connectors (E) to the oven connectors (D), matching the

colours and the alignment of the housing guides visible on the top of the

connectors.

• Then make the connection by pushing the connectors all the way in, making

sure that the tongue clicks into place.

• Unscrew the nut of the earth screw (K) on the top cover of the oven

and insert the yellow/green earth wire, leaving the washer in place. Screw

the nut back onto the screw and tighten it as far as it will go.

• Group the previously connected cables together and cover them with the

metal cover (F), taking care that the cables are not trapped under the cover.

• Tighten the two screws (G) to secure the metal cover provided with the

oven.

INSTALLATION

WARNING

The appliance must be installed by a

qualified technician who is fully aware of

current safety and installation

regulations

ELECTRICAL CONNECTION

Legend:

- R = brown

- S = brown

- E = yellow/green

- N = blue

GB11

IMPORTANT: the installer is responsible for any damage or injury resulting from

incorrect installation.

To guarantee correct operation, the appliance must be installed on a perfectly flat

surface.

For cut-out dimensions, see the figure below.

Dimensions in mm

For flush mounted installation or setting into a marble worktop, contact

the After-sales Service for the installation kit and necessary instructions.

• 4812 310 19277 Installation kit for marble worktop;

• 4801 211 00112 Installation kit for flush fitted worktop.

To guarantee correct operation, the appliance must be installed on a perfectly flat

surface.

The worktop must be 30-60 mm thick.

If necessary, cut the kitchen unit and worktop to fit before installing the hob.

Clean the cutout of any remaining dust that could compromise appliance

operation.

If a column unit is installed adjacent to the hob, leave a distance of at least 100

mm from the edge of the hob.

1. Position the clips (A) in the spaces provided on the hob trim (Fig.3) if not

already positioned.

2. Measure the centre point of the vertical sides of the cut-out (Fig. 1)

3. Fit the brackets (C) in the centre of the vertical sides, aligning the upper

edge of the brackets so that they are flush with the worktop surface (Fig.2).

4. Fix the brackets with the 4 screws supplied (B) using the holes provided.

5. Insert the hob in the cutout, making sure the clips (A) are secured in the

spaces provided (Fig.4).

Fig. 1

Fig.2

Fig.3

Fig.4

Undercounter oven installation

• If an oven (which must be of our manufacture) is to be installed under the

hob, ensure it is equipped with a cooling system and observe the distances

given in the figure to the side.

• There must be nothing between the cooktop and the oven (cross rails,

panels, brackets, etc.).

INSTALLATION AND FIXING

ASSEMBLY

490

580

510

483

553

min. 50

560

R min. 6,5

max. 8

5mm

GB12

Control Panel Description

The control panel is equipped with touch controls: to use them, just press the

corresponding symbol (a light touch is sufficient).

Switching on and adjusting cooking

zones

After positioning the pot on the chosen cooking zone, select the required power

level by turning the knob clockwise. Each cooking zone has different heat

settings, ranging from “1” (minimum power) to “9” (maximum power).

When a knob is set to a power setting between 1 and 9 the hob indicator light

switches on.

IMPORTANT: at the position indicated by a “______” on the cooktop knobs

there is no function: the heating element is switched off.

IMPORTANT: if no pot is placed on the hob or if the pot used is not suitable for an

induction hob, the cooking zone selected will switch off after 1 minute. To

reactivate it: place a pot that is suitable for the induction hob (see section “Before

use”) on the desired cooking zone, turn the knob to “0” and then select the

desired heat setting.

Switching off cooking zones

Turn the knob to “0”.

When all the knobs are set to “0” (or to the line “____”) the hob indicator light

switches off.

Care and maintenance

Clean the hob after each use in order to avoid damaging the surface and to

prevent the formation of baked-on deposits which are difficult to remove.

To clean the hob, proceed as follows:

1. use a soft clean cloth, absorbent kitchen wipes or a proprietary cleaner for

glass ceramic hobs. Do not use abrasive sponges and/or metal scouring

pads;

2. food spills should be cleaned off before they bake onto the glass ceramic

surface. Sugar and foods with a high sugar content damage the glass

ceramic surface and must be immediately removed using a scraper for glass;

3. remove any stubborn food residues with a scraper or proprietary

detergents;

4. salt, sugar and sand can scratch the glass ceramic hob: clean up any such

spills on the hob immediately.

Before contacting After-sales Service:

• Read and follow the instructions given in the section “INSTRUCTIONS FOR

USE”.

• Check that the electricity supply has not been shut off.

• Clean the hob and dry it thoroughly.

• Check that the knob is in the correct position: at position “0” or the levels

indicated by a continuous line, the cooking zones do not receive any power.

• If no pot is placed on the hob or if the pot used is not suitable for an

induction hob, the cooking zone selected will switch off after 1 minute. To

reactivate it: place a pot that is suitable for the induction hob (see section

“Before use”) on the desired cooking zone, turn the knob to “0” and then

select the desired heat setting.

• If the internal temperature of electronic parts is too high, the hob will

switch off automatically. Wait for the hob to cool down before using it

again. To resume operation, turn the knob to “0” and then to the desired

power level.

Before you call the After Sales Service:

• try to solve the problem (see “TROUBLESHOOTING GUIDE”);

• switch the appliance off, wait 30 seconds then switch it on again. to see if

the fault persists.

If after the above checks the fault persists, contact the nearest After-

sales Service.

Always provide:

• a brief description of the fault;

• the exact type and model of hob;

• the service number (number after the word Service on the rating plate) is

located on the underside of the cooktop or on the warranty booklet;

• your complete address and phone number.

If any repairs are required, please contact an authorized After-sales Service as

indicated in the warranty.

INSTRUCTIONS FOR USE

MAINTENANCE

WARNING

• Do not use steam cleaners.

• Before cleaning, leave the cooking

zones cool down

Power levels No function

Cooking zone positioning

Cooktop operation

lamp

Level selector

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

GB13

Energy saving

For optimum results, observe the following advice:

• Use pots and pans whose bottom diameter is equal to that of the cooking

zone.

• Only use flat-bottomed pots and pans.

• If possible, keep pot lids on when cooking.

• Cook vegetables, potatoes, etc. with little water in order to cut down

cooking time.

• Use a pressure cooker to to save even more energy and time.

• Make sure you place the pot or pan in the centre of the cooking zone

outlined on the hob.

Packaging

The packaging material is 100% recyclable and marked with the recycling

symbol .

Electrical Appliances

This appliance is marked in compliance with European Directive 2002/96/EC on

Waste Electrical and Electronic Equipment (WEEE). By ensuring that this

appliance is scrapped suitably, you can help prevent potentially damaging

consequences for the environment and health.

The symbol on the appliance, or on documentation enclosed with the

appliance, indicates that this product must not be treated as household waste,

but must be delivered to the nearest collection centre for the recycling of

electrical and electronic appliances. Disposal must be carried out in accordance

with local environmental regulations for waste disposal. For further information

on the treatment, recovery and recycling of this appliance, contact your

competent local authority, the collection service for household waste.

• This hob is suitable for contact with foodstuffs and complies with EEC (CE)

regulation n. 1935/2004.

• The appliances are designed, built and sold in compliance with:

- safety objectives of the “Low Voltage” Directive 2006/95/CE (which

replaces 73/23/CEE and subsequent amendments);

- protection requirements of the EMC Directive 2004/108/CE

“Electromagnetic compatibility”.

APPLIANCE DATA PLATE

MODEL SERIAL NUMBER

USER ADVICE

SAFEGUARDING THE ENVIRONMENT

DECLARATION OF CONFORMITY

Privileg PCTOC240060F Owner's manual

Brand: Privileg

Model: PCTOC240060F

Category: Hobs

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Privileg PCTOC240060F Owner's manual

This manual is also suitable for

Privileg PCTOC240060F Owner's manual

Related papers

Other documents