Alesis GuitarLink Wireless User manual

Type
User manual

This manual is also suitable for

2
User Guide (English)
1. Make sure all items listed in the Box Contents are
included.
2. READ SAFETY INSTRUCTION BOOKLET BEFORE
USING THE PRODUCT.
3. Place the product in an appropriate location for
operation.
Support
For complete system requirements, compatibility information, and product registration, visit the
Alesis website: alesis.com/guitarlink-wireless.
For additional product support, visit alesis.com/support.
Quick Setup
1. Flip the power switch to the "On" position for the transmitter and receiver.
2. Press the Pair Button on both the transmitter and the receiver. The Pair LED will be lit
solid on the transmitter and receiver when they have successfully connected.
3. Set the receiver antenna to a vertical position.
4. Connect your guitar to the transmitter and adjust your guitar’s output volume.
5. Use a standard 1/4" cable (not included) to connect the receiver's Amp Output to your
amplifier.
6. Set the volume control on the receiver to the highest level possible without distorting or
clipping the guitar signal. This level will vary with the settings of your guitar's volume and
your guitar amplifier's gain and/or volume. Adjust your guitar amplifier's volume last.
BOX CONTENTS
GuitarLink Wireless
Transmitter
GuitarLink Wireless
Receiver
Power Adapter
2 AAA Batteries
User Guide
Safety & Warranty Manual
3
Connection Diagram
Guitar*
Transmitter
Receiver
Amplifier*
* Sold
separately
4
3
4
5
1
2
3
4
2
1
2
1
2
3
1
1
3
Transmitter Features
Front Panel
1. Pair Button – Press this button to connect to the
receiver. The Pair LED will illuminate when connected
to the receiver.
2. Pair LED Illuminates when the transmitter is
connected with the receiver.
3. Power LED – Illuminates when the transmitter is powered on.
Rear Panel
1. Battery Compartment – Insert 2 AAA batteries here
to power the transmitter.
2. On/Off Switch – Slide this switch to power the
transmitter on.
3. Guitar Cable – Connect the attached 1/4” cable to
your guitar’s 1/4” output.
Bottom Panel
1. Guitar Strap Clip Use the attached clip to secure
the GuitarLink Wireless transmitter to your guitar strap
or to your pocket.
2
3
4
1
2
3
4
1
2
1
2
3
1
1
3
4
5
1
2
3
4
2
1
2
1
2
3
1
1
3
5
Receiver Features
Front Panel
1. Pair Button Press this button to
connect to the transmitter. The Pair
LED will illuminate when connected
to the transmitter.
2. Pair LED – Illuminates when the
receiver is connected with the
transmitter.
3. Power LED – Illuminates when the receiver is powered on.
4. Volume – Adjusts the volume of the signal going to the Amp Output.
5. Amp Output Use a standard 1/4" cable (not included) to connect the GuitarLink
Wireless receiver to your amplifier.
Rear Panel
1. Battery Compartment – Insert 2 AAA batteries
here to power the receiver.
2. On/Off Switch – Slide this switch to power the
receiver on.
3. Power Input Connect the included 5V 1A,
Center-Pin Positive power adapter here.
4. Antenna – Place the antenna in a vertical
position for best results in transmitting the wireless signal. If the wireless signal quality is
poor, change the position of the antenna.
2
3
4
1
2
3
4
1
2
1
2
3
1
1
3
4
5
1
2
3
4
2
1
2
1
2
3
1
1
3
6
Troubleshooting
No signal:
Make sure both the transmitter and receiver are powered on.
Make sure you are within the 60-foot (20-meter) transmitting range.
Make sure the transmitter and receiver have been paired.
Adjust the output volume on your guitar.
Make sure the volume controls on your mixer and speakers are turned up.
Check the power LEDs on both the receiver and transmitter. If one of them is off, check
that the device is powered correctly:
o Install fresh AAA batteries in the transmitter.
o Connect the power adapter to (or install fresh AAA batteries in) the receiver.
Weak signal:
Adjust the output volume on your guitar.
Make sure there are no objects (computers, walls, furniture, etc.) between the transmitter
and receiver.
Make sure you are within the 60-foot (20-meter) transmitting range.
If the transmitter or receiver is being powered from batteries, install fresh AAA batteries.
Poor signal quality:
Keep any connected audio cables away from the receiver’s antenna.
If the transmitter or receiver is being powered from batteries, install fresh AAA batteries.
27
Appendix (English)
Specifications
Dimensions (L x W x H):
Receiver: 3.5” (6.5” with antenna extended) 4.5” x 1.25”; 89 mm (165 mm with
antenna extended) x 114 mm x 32 mm
Transmitter: 2.5” x 9.2” 0.75”; 64 mm x 234 mm x 19 mm
Weight:
Receiver: 0.25 lbs (0.11 kg)
Transmitter: 0.25 lbs (0.11 kg)
Wireless Connection: 2.4 GHz wireless signal
Wireless Transmission Range: 60 feet (20 meters)
Receiver Power Adapter: 5V, 1A; Center-Pin Positive
alesis.com
Manual Version 1.0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Alesis GuitarLink Wireless User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI