Whirlpool AKR 047/01/IX User guide

INSTRUCTIONS FOR USE 3

MODE D’EMPLOI 19

3

ﻝﺎﻤﻌﺘﺳﻻﺍ ﺕﺎﻤﻴﻠﻌﺗ

3

INSTRUCTIONS FOR USE

Page

IMPORTANT SAFETY INSTRUCTIONS 4

INSTALLATION 9

SAFEGUARDING THE ENVIRONMENT 12

TROUBLESHOOTING GUIDE 13

DECLARATION OF CONFORMITY 13

AFTER-SALES SERVICE 13

CLEANING 14

MAINTENANCE 15

4

IMPORTANT SAFETY INSTRUCTIONS

YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT

This manual and the appliance itself provide important safety warnings, to be read and

observed at all times.

This is the danger symbol, pertaining to safety, which alerts users to potential risks to

themselves and others.

All safety warnings are preceded by the danger symbol and the following terms:

DANGER

Indicates a hazardous situation which, if not avoided, will

cause serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could

cause serious injury.

All safety warnings give specic details of the potential

risk present and indicate how to reduce risk of injury,

damage and electric shock resulting from improper

use of the appliance. Carefully observe the following

instructions:

• Use protective gloves to perform all unpackaging and

installation operations.

• This appliance is extremely heavy accordingly, it must

be lifted and handled by two or more people in order

to avoid any risks or injuries.

• The appliance must be disconnected from the power

supply before carrying out any installation work.

• Installation and maintenance must be carried

out by a qualied technician, in compliance with

the manufacturer’s instructions and local safety

regulations. Do not repair or replace any part of the

appliance unless specically stated in the user manual.

WARNING

If the information in this manual is not followed exactly, a

re or explosion may result causing property damage or

injury.

5

• Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this appliance.

What to do if you smell gas:

- Do not try to light any appliance.

- Do not touch any electrical switch.

- Do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

- If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualied installer, service agency or

the gas supplier.

- Use appliance in well ventilated rooms only.

The electrical and gas connections must comply with

local regulations

• Use only exible or rigid metal hose for gas

connection.

• The use of a gas appliance produces heat and humidity

in the room. Make sure the room is well-ventilated, or

install an extractor hood with exhaust duct.

• In case of prolonged use, additional ventilation may

be necessary (by opening a window or increasing the

hood extraction speed).

• After use, make sure the knob is in o position and

close the main gas supply cock or the gas cylinder

valve.

• Keep the packaging materials out of the reach of

children.

• Power cable replacement must be carried out by a

qualied electrician. Contact an authorized service

centre.

• Regulations require that the appliance is earthed.

6

• The power cable must be long enough for connecting

the appliance, once tted in its housing, to the main

power supply.

• For installation to comply with current safety

regulations, an allpole disconnect switch with

minimum contact gap of 3mm must be utilized.

• Do not use multiple plug adaptors if the oven is tted

with a plug.

• Do not use extension leads.

• Do not pull the power supply cable.

• The electrical components must not be accessible to

the user after installation.

• Do not touch the appliance with any wet part of the

body and do not operate it when barefoot.

• This appliance is designed solely for use as a domestic

appliance for cooking food. No other type of use is

permitted (e.g.: heating rooms). The Manufacturer

declines all responsibility for inappropriate use or

incorrect setting of the controls.

• The appliance and its accessible parts become hot

during use. Care should be taken to avoid touching

heating elements. Very young (0-3 years) and

young children (3-8 years) shall be kept away unless

continuously supervised

• Children from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge can use this

appliance only if they are supervised or have been

given instructions on safe appliance use and if they

understand the hazards involved. Children shall

7

not play with the appliance. Cleaning and user

maintenance shall not be made by children without

supervision.

• During and after use, do not touch the heating

elements or interior surfaces of the appliance - risk of

burns. Do not allow the appliance to come into contact

with cloths or other ammable materials until all the

components have cooled down completely.

• At the end of cooking, exercise caution when opening

the appliance door, letting the hot air or steam exit

gradually before accessing the oven. When the

appliance door is shut, hot air is vented from the

aperture above the control panel. Do not obstruct the

vent apertures.

• Use oven gloves to remove pans and accessories,

taking care not to touch the heating elements.

• Do not place ammable materials in or near the

appliance: a re may break out if the appliance is

inadvertently switched on.

• Do not heat or cook sealed jars or containers in the

appliance. The pressure that builds up inside might

cause the jar to explode, damaging the appliance.

• Do not use containers made of synthetic materials.

• Overheated oils and fats catch re easily. Always

remain vigilant when cooking foods rich in fat and oil.

• Never leave the appliance unattended during food

drying.

• If alcoholic beverages are used when cooking foods

(e.g. rum, cognac, wine), remember that alcohol

evaporates at high temperatures. As a result, there is a

8

risk that vapours released by the alcohol may catch re

upon coming into contact with the electrical heating

element.

• Never use steam cleaning equipment.

• Do not touch the oven during the pyrolysys cycle. Keep

children away from the oven during the pyrolysis cycle.

(only for ovens with Pyrolisis function).

• Only use the temperature probe recommended for this

oven.

• Do not use harsh abrasive cleaners or sharp metal

scrapers to clean the oven door glass since they can

scratch the surface, which may result in shattering of

the glass.

• Ensure that the appliance is switched o before

replacing the lamp to avoid the possibility of electric

shock.

Scrapping of household appliances

- This appliance is manufactured with recyclable or reusable materials. Scrap

the appliance in accordance with local regulations on waste disposal.

Before scrapping, cut o the power cords so that the appliances cannot be

connected to the mains.

- For further information on the treatment, recovery and recycling of

household electrical appliances, contact your competent local authority, the

collection service for household waste or the store where you purchased the

appliance.

9

INSTALLATION

Unpack the oven and make sure that the oven has not been damaged during transport and that

the oven door closes properly.

In the event of problems, contact the dealer or your nearest After-sales Service. To prevent any

damage, only remove the oven from its polystyrene foam base at the time of installation.

TECHNICAL INFORMATION FOR THE INSTALLER

• Use protective gloves for handling, preparing and installing the product.

• Before installation, make sure that:

- the local gas delivery conditions (nature and pressure) are compatible with the

settings of the oven (see the rating plate and injector table);

- this appliance is not connected to a fume exhaust device. It shall be installed in accordance

with current installation regulations. Particular attention shall be given to the relevant

requirements regarding ventilation;

- combustion products are discharged outdoors through specic hoods or wall and/or

window mounted electrical fans.

PREPARING THE HOUSING UNIT

• Kitchen units in contact with the oven must be heat resistant (min 90°C).

• Carry out all cabinet cutting work before tting the oven in the housing and carefully remove

all wood chips and sawdust.

• After installation, the bottom of the oven must no longer be accessible.

• For correct appliance operation, do not obstruct the minimum gap between the worktop and

the upper edge of the oven.

10

INSTRUCTIONS FOR THE INSTALLER

INSTRUCTIONS FOR INSTALLATION OF THE APPLIANCE

(positioning and ventilation requirements)

The regulations covering the installation, maintenance and

operation of gas appliances for domestic use are applicable

regulations.

An extract of these regulations appears below. For all indications

not covered, refer to the above-mentioned regulations.

POSITIONING:

(Fig. 1) the products of combustion from cooking appliances

must always be discharged into suitable extractor hoods,

which must be connected to a chimney, ue or vented directly

to outside the building. In situations where it is not possible

to install an extractor hood, an electric extractor fan installed

in a window or external wall may be used, provided that all

requirements of the ventilation regulations are satised; the fan

should switch on whenever the appliance is in operation.

VENTILATION:

(Fig. 1) it is essential that the room in which gas appliances are

installed is adequately ventilated to ensure that all the appliances

receive the required quantity of fresh air for combustion.

To ensure an adequate air ow, it may be necessary to create

apertures in accordance with the following requirements:

a) with cross-sectional area of 6 cm

2

per kW with a minimum

cross-sectional area of 100 cm

2

(these apertures may also be

created by increasing the gap between the bottom of doors

and the oor);

b) situated at the bottom of an external wall, preferably opposite

the wall on which combustion products are extracted ;

c) the positions of the apertures should selected so as to avoid

the possibility of their being obstructed and, if made in

external walls, they must be protected with grilles, metal

meshes, etc. installed on the outside face of the wall.

Fig. 1

11

If an electric extractor fan for the removal of foul air is installed in the room, the apertures provided

for air changes must allow a ventilation rate of at least 35 m

3

/h per kW of power installed.

GAS CONNECTION

WARNING

This operation must be performed by a qualied technician.

• The gas supply system must comply with local regulations.

• You can nd specic local regulations for some countries in the paragraph “Reference to Local

Regulations”. If no information concerning your Country is given, please ask details to your Installer.

• The connection of the oven to the gas pipe network or gas cylinder must be made by means

of a rigid copper or steel pipe with ttings complying with local regulations, or by means of

a continuous-surface stainless steel hose complying with local regulations. The maximum

length of the hose is 2 linear metres.

• Connect elbow (A) supplied with to the oven inlet main pipe and interpose the washer (B)

supplied, in compliance with EN549.

IMPORTANT: if a stainless steel hose is used, it must be

installed so as not to touch any mobile part of the furniture.

It must pass through an area where there are no obstructions

and where it is possible to inspect it on all its length.

• After connection to the gas supply, check for leaks with soapy

water. Light up the burners and turn the knobs from max

position to minimum position to check ame stability.

ELECTRICAL CONNECTION

Make sure the power voltage specied on the appliance dataplate is the same as the mains

voltage. The dataplate is on the front edge of the oven (visible when the door is open).

• Power cable replacement (type H05 RR-F 3 x 1.5 mm

2

) must be carried out by a qualied

electrician. Contact an authorized service centre.

CABLE TYPES AND MINIMAL DIAMETERS

H05RR-F 3x1.5 mm²

H05VV-F 3x1.5 mm²

H05RN-F 3x1.5 mm²

H05V2V2-F 3x1.5 mm²

12

GENERAL RECOMMENDATIONS

Before use:

- Remove cardboard protection pieces, protective lm and adhesive labels from accessories.

- Remove the accessories from the oven and heat it at the MAX temperature for 30 minutes

to eliminate the smell and fumes from the insulating materials and protective grease.

Clean the oven thoroughly with soapy water and rinse well. To remove the lateral frames from

smooth-walled ovens, proceed as shown in the chart.

Operate the oven for about 20 minutes at maximum temperature to burn o all traces of grease

which might otherwise create unpleasant smells when cooking.

During use:

• Do not place heavy objects on the door as they could damage it.

• Do not cling to the door or hang anything from the handle.

• Do not cover the inside of the oven with aluminium foil.

• Do not pour water into the inside of a hot oven; this could damage the enamel coating.

• Do not drag pots or pans across the bottom of the oven as this could damage the enamel coating.

• Make sure that the electrical cables of other appliances do not touch hot parts of the oven or

become trapped in the door.

• Do not expose the oven to atmospheric agents.

SAFEGUARDING THE ENVIRONMENT

Disposal of packing material

The packing material is 100% recyclable and is marked with the recycle symbol . The various

parts of the packing must therefore be disposed of responsibly and in full compliance with local

authority regulations governing waste disposal.

Scrapping the product

- This appliance is marked in compliance with European Directive 2002/96/EC, Waste

Electrical and Electronic Equipment (WEEE).

- By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product.

- The symbol on the product or on the accompanying documentation indicates that it

should not be treated as domestic waste but must be taken to an appropriate collection

centre for the recycling of electrical and electronic equipment.

Energy saving

- Only pre-heat the oven if specied in the cooking table or your recipe.

- Use dark lacquered or enamelled baking moulds as they absorb heat far better.

13

TROUBLESHOOTING GUIDE

If the oven will not operate correctly, before calling the After-Sales Service, refer to the

Troubleshooting Guide to determine the problem.

1. The burner fails to ignite or the ame is not even

Check that:

• The gas or electrical supplies are not shut o and especially that the gas supply tap is open.

• The gas cylinder (liquid gas) is not empty.

• The burner openings are not clogged.

• The plug end is not dirty.

• All the burner parts have been positioned correctly.

2. The burner does not stay lit

Check that:

• When lighting the burner, the knob has been pressed for enough time to activate the

protection device.

• The burner openings are not clogged near the thermocouple.

• The end of the safety device is not dirty.

• The minimum gas setting is correct (see relevant paragraph).

DECLARATION OF CONFORMITY

- This oven, which is intended to come into contact with foodstus, complies with European

Regulation ( ) n.1935/2004 and has been designed, manufactured and sold in conformity

with the safety requirements of the “Low Voltage” directive 2006/95/EC (which replaces 73/23/

EEC and subsequent amendments), the protection requirements of “EMC” 2004/108/EC.

This oven has been designed, constructed and marketed in compliance with:

- safety requirements of “Gas” Directive 2009/142/EC (ex: EEC 90/396);

AFTER-SALES SERVICE

Before calling the After-Sales Service:

1. See if you can solve the problem yourself with the help of the suggestions given in the

“Troubleshooting guide”.

If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.

Always specify:

• a brief description of the fault;

• the type and exact model of the oven;

• the service number (number after the word Service on the rating plate), located on the right

hand edge of the oven cavity (visible when the oven door is open). The service number is also

indicated on the guarantee booklet;

• your full address;

• your telephone number.

If any repairs are required, please contact an authorised After-sales Service (to guarantee that

original spare parts will be used and repairs carried out correctly).

14

CLEANING

WARNING

- Do not use steam cleaners.

- Only clean the oven when it is cool to the touch.

- Disconnect the appliance from the power supply.

Exterior of the oven

IMPORTANT: Do not use corrosive or abrasive detergents. If any of these products

accidentally comes into contact with the appliance, clean it immediately with a damp

cloth.

• Clean the surfaces with a damp cloth. If very dirty, add a few drops of neutral detergent to the

water. Dry with a dry cloth.

Oven interior:

Important: do not use abrasive sponges or metallic scrapers or scourers. Over time, these

can ruin enamelled surfaces and the oven door glass.

• After every use, allow the oven to cool then clean it preferably while it is still warm in order to

remove built-up dirt and stains caused by food residues (e.g. food with a high sugar content.

• Use specic oven detergents and follow the manufacturer’s instructions to the letter.

• Clean the door glass with a suitable liquid detergent. The oven door can be removed to

facilitate cleaning (see MAINTENANCE).

N.B: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables,

etc.) condensation may form on the inside of the door and around the seal. When the oven

is cold, dry the inside of the door with a cloth or sponge.

Accessories:

• Soak the accessories in water with washing up detergent immediately after use, handling

them with oven gloves if still hot.

• Food residues can be easily removed using a brush or sponge

15

MAINTENANCE

WARNING

- Use safety gloves.

- Ensure the oven is cold before carrying out the

following operations.

- Disconnect the appliance from the power supply.

REMOVING THE DOOR

To remove the door:

2. Open the door fully.

3. Lift the catches and push them forwards as far as they will go (Fig. 1).

4. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).

To ret the door:

5. Insert the hinges in their seats.

6. Open the door fully.

7. Lower the two catches.

8. Close the door.

Fig. 1 Fig. 2

To remove the side grilles

To press down the grilles and lift up as shown in g. 3.

Fig. 3

16

ADJUSTMENT TO DIFFERENT TYPES OF GAS

WARNING

This operation must be performed by a qualied

technician.

If the appliance is intended to operate with a dierent gas from the gas type stated on the

rating plate and information label on the back side, close to the gas pipe, and on the bottom of

the frontal oven door frame when the door is open. Change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• The gas injectors must be changed by After Sales Service or a qualied technician.

• Injectors not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must

be tightened as far as it will go.

IMPORTANT: should you experience diculty in turning the burners knobs, please contact

the After Sales Service for the replacement of the burner tap if found to be faulty.

IMPORTANT: when gas cylinder is adopted, the gas cylinder or gas container must be

properly settled (vertical orientation).

17

REPLACING THE INJECTORS

(see the injector table in the Instruction)

WARNING

This operation must be

performed by a qualied

technician.

For the Oven , lower side

1) Remove the burner cover plate. (Fig. 1)

2) Remove the screw securing the oven burner and

withdraw the burner from the support together with the

heat sensor and the ignition spark plug. (Fig. 2)

3) Remove the nozzle using a 7 mm socket wrench. (Fig. 3)

4) Screw the new injector in fully (diameter in hundredths

of millimetre stamped on the injector), taking care not to

cross the thread.

5) Replace the burner reversing the operations in step 2

above.

6) Replace the cover plate.

7) Adjusting the minimum ame.

Before installing the oven, remember to ax the gas

calibration plate supplied with the injectors in such a

way that it covers the existing information relating to gas

calibration.

For the Grill, upper side

1) Remove the burner screw located at top front of the oven

cavity. (Fig.4 and 4a)

2) Remove the burner together with its heat elements.

3) Remove the injector using the 7 mm socket wrench.

(Fig.5)

4) Fully tighten the new injector which must be of the

diameter indicated in the table in the chart table on

page6.

5) Put back the burner and secure it with the screw.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 4a

Fig. 5

18

REPLACING THE OVEN LAMP

To replace the two rear lamps (g. 4):

• Disconnect the oven from the power supply.

• Unscrew the lamp cover (Fig. 5), replace the lamp (see note for lamp type) and screw the lamp

cover back on.

• Reconnect the oven to the power supply.

Fig. 4 Fig. 5

N.B.:

- Only use 25W / 230V type E14, T300°C incandescent lamps.

- The lamp used in the appliance is specically designed for electrical appliances and is not

suitable for household room illumination (Commission Regulation (EC) No 244/2009).

- Lamps are available from our After-sales Service.

19

MODE D’EMPLOI

Page

INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ 20

INSTALLATION 26

CONSEILS POUR LA PROTECTION DE L’ENVIRONNEMENT 29

DIAGNOSTIC DES PANNES 30

DÉCLARATION DE CONFORMITÉ 30

SERVICE APRÈS-VENTE 30

NETTOYAGE 31

ENTRETIEN 32

20

INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ

VOTRE SÉCURITÉ ET CELLE D’AUTRUI EST TRÈS IMPORTANTE

Le présent manuel contient d’importants messages relatifs à la sécurité, qui gurent également

sur l’appareil. Nous vous invitons à les lire soigneusement et à les respecter en toute circonstance.

Ceci est le symbole de danger relatif à la sécurité. Il met en garde l’utilisateur et toute

autre personne contre les risques potentiels dérivant de l’utilisation de cet appareil.

Tous les messages relatifs à la sécurité sont précédés du symbole de danger et des

termes suivants:

DANGER

Indique une situation dangereuse qui, si elle n’est pas

évitée, provoque des blessures graves.

AVERTISSEMENT

Indique une situation dangereuse qui, si elle n’est pas

évitée, est susceptible de provoquer des blessures graves.

Tous les messages relatifs à la sécurité spécient le

danger potentiel auquel ils se réfèrent et indiquent

comment réduire le risque de blessures, de dommages

et de chocs électriques résultant d’une utilisation

non réglementaire de l’appareil. Veuillez observer

scrupuleusement les instructions suivantes:

• Revêtez des gants de protection avant de procéder au

déballage et à l’installation de l’appareil.

• Compte-tenu de son poids et pour des raisons de

sécurité, la manutention et l’installation de l’appareil

nécessitent la présence d’au moins deux personnes.

• Débranchez l’appareil de l’alimentation secteur avant

de procéder aux opérations d’installation.

• Les opérations d’installation et d’entretien sont du ressort

exclusif d’un technicien spécialisé. Celui-ci est tenu

de se conformer aux instructions du fabricant et aux

normes locales en vigueur en matière de sécurité. Évitez

de réparer ou de remplacer les pièces, sauf indication

contraire expressément mentionnée dans le manuel.

Page is loading ...

Whirlpool AKR 047/01/IX User guide

Whirlpool AKR 047/01/IX User guide

in other languages

Related papers

Other documents