NordicTrack T 7.0 Treadmill User manual

Brand: NordicTrack

Model: T 7.0 Treadmill

Category: Treadmills

Type: User manual

This manual is also suitable for

NETL81810.0

Serial Number

Decal

Model No. NETL81810.0

Serial No.

Write the serial number in the space

above for reference.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

QUESTIONS?

If you have questions, or if there are

missing parts, please contact us:

Call: 08457 089 009

From Ireland: 053 92 36102

Website: www.iconsupport.eu

E-mail: [email protected]

Write:

ICON Health & Fitness, Ltd.

c/o HI Group PLC

Express Way

Whitwood, West Yorkshire

WF10 5QJ

AUSTRALIA

Call: 1-800-237-173

E-mail:

[email protected]

USERʼS MANUAL

www.iconeurope.com

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

SSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

RECYCLING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

This drawing shows the locations of the

warning decals. If a decal is missing or il-

legible, call the telephone number on the

front cover of this manual and request a

free replacement decal. Apply the decal

in the location shown. Note: The decals

may not be shown at actual size.

WARNING DECAL PLACEMENT

NordicTrack is a registered trademark of ICON IP, Inc.

1. Before beginning any exercise program, con-

sult your physician. This is especially impor-

tant for persons over age 35 or persons with

pre-existing health problems.

2. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

3. Use the treadmill only as described.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Place the treadmill on a level surface, with at

least 8 ft. (2.4 m) of clearance behind it and 2

ft. (0.6 m) on each side. Do not place the

treadmill on any surface that blocks air open-

ings. To protect the floor or carpet from dam-

age, place a mat under the treadmill.

6. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

7. Keep children under age 12 and pets away

from the treadmill at all times.

8. The treadmill should be used only by persons

weighing 300 lbs. (135 kg) or less.

9. Never allow more than one person on the

treadmill at a time.

10. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended

for both men and women. Always wear ath-

letic shoes. Never use the treadmill with bare

feet, wearing only stockings, or in sandals.

11. When connecting the power cord (see page

16), plug the power cord into an earthed cir-

cuit. No other appliance should be on the

same circuit. When replacing the fuse in the

power cord adapter, insert an ASTA-approved

BS1362, 13-amp fuse into the fuse carrier.

12. If an extension cord is needed, use only a 3-

conductor, 14-gauge (1 mm

) cord that is no

longer than 5 ft. (1.5 m).

13. Keep the power cord away from heated sur-

faces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See TROU-

BLESHOOTING on page 25 if the treadmill is

not working properly.)

15. Read, understand, and test the emergency

stop procedure before using the treadmill (see

HOW TO TURN ON THE POWER on page 18).

16. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

17. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

18. The pulse sensor is not a medical device.

Various factors, including the user's move-

ment, may affect the accuracy of heart rate

readings. The pulse sensor is intended only

as an exercise aid in determining heart rate

trends in general.

WARNING: To reduce the risk of serious injury, read all important precautions and in-

tructions in this manual and all warnings on your treadmill before using your treadmill. ICON as-

sumes no responsibility for personal injury or property damage sustained by or through the use of

this product.

IMPORTANT PRECAUTIONS

9. Never leave the treadmill unattended while it

is running. Always remove the key, unplug

the power cord, and press the power switch

into the off position when the treadmill is not

in use. (See the drawing on page 5 for the lo-

cation of the power switch.)

20. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6, and HOW TO FOLD

AND MOVE THE TREADMILL on page 24.)

You must be able to safely lift 45 lbs. (20 kg)

to raise, lower, or move the treadmill.

21. When folding or moving the treadmill, make

sure that the storage latch is holding the

frame securely in the storage position.

22. Never insert any object into any opening on

the treadmill.

3. Inspect and properly tighten all parts of the

treadmill regularly.

24.

DANGER: Always unplug the power

cord immediately after use, before cleaning the

treadmill, and before performing the mainte-

ance and adjustment procedures described in

this manual. Never remove the motor hood un-

less instructed to do so by an authorized ser-

vice representative. Servicing other than the

procedures in this manual should be performed

by an authorized service representative only.

25. This treadmill is intended for in-home use

only. Do not use this treadmill in a commer-

cial, rental, or institutional setting.

26. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

SAVE THESE INSTRUCTIONS

Thank you for selecting the revolutionary NordicTrack

7.0 treadmill. The T 7.0 treadmill offers an impres-

sive selection of features designed to make your work-

outs at home more enjoyable and effective. And when

youʼre not exercising, the unique treadmill can be

olded up, requiring less than half the floor space of

other treadmills.

For your benefit, read this manual carefully before

using the treadmill. If you have questions after read-

ing this manual, please see the front cover of this man-

al. To help us assist you, please note the product

model number and serial number before contacting us.

The model number and the location of the serial num-

ber decal are shown on the front cover of this manual.

Before reading further, please review the drawing

below and familiarize yourself with the labeled parts.

BEFORE YOU BEGIN

Handrail

Upright

Tray

Key/Clip

Power Switch

Walking Belt

Platform Cushion

Foot Rail

Idler Roller

Adjustment Bolts

Console

Pulse Sensor

ASSEMBLY

ssembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not

dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking

belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of

the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubri-

ant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys and your own Phillips screwdriver ,

adjustable wrench , needlenose pliers , and scissors .

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is

the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses

is the quantity needed for assembly. Note: Some small parts may have been preassembled. To avoid dam-

aging parts, do not use power tools for assembly. Extra hardware may be included.

#8 x 3/4" Screw

(1)–10

3/8" Star

Washer (11)–6

#8 x 1" Tek Screw

(5)–4

3/8" Nut (10)–3

5/16" Star

Washer (13)–2

#10 Star

Washer (12)–4

#8 x 1" Screw

(53)–4

#10 x 3/4" Screw

(2)–4

3/8" x 1 1/2"

Patch Bolt (3)–2

5/16" x 1" Flat Head

Patch Bolt (14)–4

3/8" x 4" Patch Bolt (7)–4

1/4" x 1" Patch

Bolt (9)–4

3/8" x 2" Bolt (8)–3

5/16" x 1"

Patch Bolt (4)–2

2. With the help of a second person, carefully tip

the treadmill onto its left side. Partially fold the

Frame (55) so that the treadmill is more stable;

do not fully fold the Frame yet.

Remove and discard the two indicated bolts (B)

and the shipping bracket (C).

Cut the shipping tie securing the Upright Wire

(87) to the Base (95). Locate a plastic tie in the

indicated hole in the Base, and use the tie to pull

the Upright Wire out of the hole.

Attach two Base Feet (90) to the Base (95) in the

locations shown with two #8 x 1" Tek Screws (5)

and two Base Foot Spacers (94).

Then, attach the other two Base Feet (90) with

two #8 x 1" Tek Screws (5).

Hole

. Make sure that the power cord is unplugged.

emove the 3/8" Nut (10), the 3/8" x 2" Bolt (8),

and the shipping bracket (A) from the Base (95).

Repeat this step on the other side of the

treadmill.

The 3/8" Nuts (10) and the 3/8" x 2" Bolts (8) will

be used in assembly steps 3 and 6. Discard the

shipping brackets.

4. Identify the Right Upright (85), which is marked

with a “Right” sticker. Hold the Right Upright

near the Base (95) as shown.

See the inset drawing. Tie the wire tie in the

Right Upright (85) securely around the end of

the Upright Wire (87). Then, pull the other end

of the wire tie until the Upright Wire is routed

completely through the Right Upright.

Wire Tie

Wire

Tie

3. See the inset drawing. Cut the plastic tie near

the Upright Wire (87).

ttach a Wheel (96) to the Base (95) with the

3/8" x 2" Bolt (8) and the 3/8" Nut (10) that you

emoved in step 1. Do not overtighten the Nut;

the Wheel must turn freely.

Press a Base Cap (89) into the Base (95).

Plastic Tie

Cut

5. Hold the Right Upright (85) against the Base

(95). Be careful not to pinch the Upright Wire

(87). Insert two 3/8" x 4" Patch Bolts (7) and a

3/8" x 1 1/2" Patch Bolt (3) with three 3/8" Star

Washers (11) into the Right Upright.

Tighten the 3/8" x 4" Patch Bolts (7) and the

3/8" x 1 1/2" Patch Bolt (3) until the heads of the

Patch Bolts touch the Right Upright (85); do not

fully tighten the Patch Bolts yet.

6. With the help of a second person, carefully tip

the treadmill onto its right side. Partially fold the

Frame (55) so that the treadmill is more stable;

o not fully fold the Frame yet.

emove and discard the two indicated bolts (B)

and the shipping bracket (C).

Attach a Wheel (96) to the Base (95) with the

3/8" x 2" Bolt (8) and the 3/8" Nut (10) that you

removed in step 1. Do not overtighten the Nut;

the Wheel must turn freely.

Press a Base Cap (89) into the Base (95).

7. Hold the Left Upright (84) against the Base (95).

Insert two 3/8" x 4" Patch Bolts (7) and a 3/8" x

1 1/2" Patch Bolt (3) with three 3/8" Star

Washers (11) into the Left Upright.

Tighten the 3/8" x 4" Patch Bolts (7) and the

3/8" x 1 1/2" Patch Bolt (3) until the heads of the

Patch Bolts touch the Left Upright (84); do not

fully tighten the Patch Bolts yet.

With the help of a second person, tip the tread-

mill so that the Base (95) is flat on the floor.

8. Identify the Left Base Cover (88) and the Right

Base Cover (91). Slide the Left Base Cover onto

the Left Upright (84) and the Right Base Cover

onto the Right Upright (85).

9. Identify the Left Upright Cover (80). Slide the

Left Upright Cover onto the Left Upright (84).

Identify the Left Handrail (82). Remove the tie

from the bracket on the Left Handrail. If neces-

sary, press the 5/16" Cage Nut (38) back into

place.

Attach the Left Handrail (82) to the Left Upright

(84) with two 5/16" x 1" Flat Head Patch Bolts

(14), a 5/16" x 1" Patch Bolt (4), and a 5/16"

Star Washer (13) as shown. Do not tighten the

Patch Bolts yet.

10. Slide the Right Upright Cover (86) onto the

Right Upright (85). Remove the tie from the

bracket on the Right Handrail (83). If necessary,

ress the 5/16" Cage Nut (38) back into place.

Hold the Right Handrail (83) near the Right

Upright (85). Insert the Upright Wire (87)

hrough the bracket on the bottom of the Right

Handrail. Pull the Upright Wire out of the end of

the Right Handrail.

Attach the Right Handrail (83) to the Right

Upright (85) with two 5/16" x 1" Flat Head Patch

Bolts (14), a 5/16" x 1" Patch Bolt (4), and a

5/16" Star Washer (13) as shown. Do not

tighten the Patch Bolts yet.

racket

11. Set the console assembly face down on a soft

surface to avoid scratching the console assem-

bly. Remove the two #8 x 3/4" Screws (1). Lift

off the Crossbar (107).

107

Console

Assembly

12. IMPORTANT: To avoid damaging the

Crossbar (107), do not use power tools and

do not overtighten the #10 x 3/4" Screws (2).

rient the Crossbar (107) as shown. Attach the

Crossbar to the Handrails (82, 83) with four #10

x 3/4" Screws (2) and four #10 Star Washers

(12); do not tighten the Screws yet.

Insert the Console Frame (102) into the

Handrails (82, 83). Attach the Console Frame

with four 1/4" x 1" Patch Bolts (9); do not

tighten the Patch Bolts yet. Be careful not to

pinch the Upright Wire (87).

Tighten one #10 x 3/4" Screw (2) in each end

of the Crossbar (107); do not overtighten the

Screws. Then, tighten the other #10 x 3/4"

Screw (2) in each end of the Crossbar.

Tighten the four 1/4" x 1" Patch Bolts (9).

107

102

irst

First

13. Firmly tighten two 5/16" x 1" Patch Bolts (4) and

the four 5/16" x 1" Flat Head Patch Bolts (14)

(only one side is shown).

With the help of a second person, hold the con-

sole assembly near the Right Handrail (83) and

the Left Handrail (not shown).

Connect the Upright Wire (87) to the console

wire. See the inset drawing. The connectors

should slide together easily and snap into

place. If they do not, turn one connector and try

again. IF YOU DO NOT CONNECT THE CON-

NECTORS PROPERLY, THE CONSOLE MAY

BECOME DAMAGED WHEN YOU TURN ON

THE POWER. Remove the wire tie from the

Upright Wire.

Connect the ground wire from the console as-

sembly to the Console Ground Wire (52).

Console

Assembly

Console

Wire

Tie

Ground Wire

Console

Wire

14. Set the console assembly on the Left and Right

Handrails (82, 83). Be careful not to pinch any

wires. Insert the excess Upright Wire (87) into

the Right Handrail.

Attach the console assembly to the Crossbar

(107) with six #8 x 3/4" Screws (1). Start all six

Screws, and then tighten each of them.

Attach the two Console Clamps (105) to the

console assembly with four #8 x 1" Screws (53).

105

onsole

Assembly

107

15. Hold the Right Upright Cover (86) against the

console assembly. Align the holes in the Right

Upright Cover with the holes in the Right Upright

(85). Attach the Right Upright Cover with two #8

x 3/4" Screws (1).

Attach the Left Upright Cover (80) to the Left

Upright (84) in the same way.

See steps 5 and 7. Tighten the 3/8" x 4" Patch

Bolts (7) and the 3/8" x 1 1/2" Patch Bolts (3).

Console

Assembly

16. If necessary, press the Left Tray (103) and the

Right Tray (104) into the console assembly.

103

onsole

Assembly

17. Raise the Frame (55) to the position shown.

Have a second person hold the Frame until

this step is completed.

Orient the Storage Latch (51) so that the large

barrel and the latch knob are oriented as shown.

Attach the Latch Bracket (6) and Storage Latch

(51) to the Base (95) with two 3/8" x 2" Bolts (8)

and two 3/8" Nuts (10).

Attach the upper end of the Storage Latch (51)

to the bracket on the Frame (55) with a 3/8" x 2"

Bolt (8) and a 3/8" Nut (10). Note: It may be

necessary to move the Frame back and forth to

align the Storage Latch with the bracket.

Lower the Frame (55) (see HOW TO LOWER

THE TREADMILL FOR USE on page 24).

18. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic

on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.

Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is

used to adjust the walking belt (see pages 26 and 27).

Large

Barrel

Latch Knob

If you purchase the optional chest pulse sensor (see page 23), follow the steps below to install the re-

ceiver included with the chest pulse sensor.

. Make sure that the power cord is unplugged.

Remove the indicated #8 x 3/4" Screw (1) from

he Access Door (108) on the back of the con-

sole assembly.

2. See the inset drawing. Hold the receiver so

that the antenna is oriented as shown. Peel

the paper backing off the pad on the bottom of

the receiver. Press the receiver onto the Access

Door (108) in the location shown.

3. Connect the wire on the receiver to the wire ex-

tending from the console assembly. Make sure

that no wires are pinched. Reattach the

Access Door (108) with the #8 x 3/4" Screw (1).

Discard the other wires included with the re-

ceiver.

Console

Assembly

108

Wires

Receiver

Antenna

108

HE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high-

performance lubricant. IMPORTANT: Never apply sil-

cone spray or other substances to the walking belt

or the walking platform. Such substances will dete-

riorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

This product must be earthed. If it should malfunc-

tion or break down, earthing provides a path of least

resistance for electric current to reduce the risk of elec-

tric shock. This product is equipped with a power cord

having an equipment-earthing conductor and an earth-

ing plug. IMPORTANT: If the power cord is dam-

aged, it must be replaced with a manufacturer-

recommended power cord.

Follow the steps below to plug in the power cord.

1. Plug the indicated end of the power cord into the

socket on the treadmill.

. If you are plugging in the power cord in

Australia, go to step 3.

If you are plugging in the power cord in the UK,

irst press the pins on the power cord into the metal

clips in the adapter as shown. Close the adapter

cover over the end of the power cord and tighten the

screw in the adapter. IMPORTANT: Make sure that

the screw is tightened into the adapter cover.

Then, go to step 3.

3. Plug the power cord into an appropriate outlet that is

properly installed and earthed in accordance with all

local codes and ordinances.

DANGER: Improper connection of

the equipment-earthing conductor can result

in an increased risk of electric shock. Check

with a qualified electrician or serviceman if

you are in doubt as to whether the product is

properly earthed. Do not modify the plug pro-

vided with the product—if it will not fit the

outlet, have a proper outlet installed by a

qualified electrician.

OPERATION AND ADJUSTMENT

Socket on Treadmill

Metal

Clips

Pins

Screw

Adapter

Outlet

Australia

Adapter

Cover

Outlet

Power Cord

FEATURES OF THE CONSOLE

The treadmill console offers an impressive array of

features designed to make your workouts more effec-

tive and enjoyable.

When the manual mode of the console is selected, you

can change the speed and incline of the treadmill with

the touch of a button. As you exercise, the console will

display instant exercise feedback. You can even mea-

sure your heart rate using the handgrip pulse sensor or

the optional chest pulse sensor.

In addition, the console offers sixteen preset work-

outs—eight quick calorie burn workouts and eight

quick timed workouts. Each workout automatically con-

trols the speed and incline of the treadmill as it guides

you through an effective exercise session.

The console also features the iFit interactive workout

system. The iFit system accepts iFit cards with work-

outs that help you achieve specific fitness goals. For

example, lose unwanted pounds with the 8-week

Weight Loss workout. iFit workouts automatically con-

trol the treadmill. iFit cards are available separately. To

purchase iFit cards at any time, go to www.iFit.com

or call the telephone number on the front cover of

this manual. iFit cards are also available at select

stores.

You can even listen to your favorite workout music or

audio books with the consoleʼs premium stereo sound

system while you get in shape.

To turn on the power, see page 18. To use the man-

ual mode, see page 18. To use a preset workout,

see page 21. To use an iFit workout, see page 22.

To use the information mode, see page 23. To use

the stereo sound system, see page 23.

IMPORTANT: If there is a sheet of plastic on the

console, remove the plastic. To prevent damage to

the walking platform, wear clean athletic shoes

while using the treadmill. The first time the tread-

mill is used, observe the alignment of the walking

belt, and center the walking belt if necessary (see

page 27).

CONSOLE

DIAGRAM

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to

old temperatures, allow it to warm to room tem-

perature before turning on the power. If you do not

o this, you may damage the console displays or

other electrical components.

Plug in the power cord (see

page 16). Next, locate the

power switch on the tread-

mill frame near the power

cord. Press the power

switch into the reset

position.

IMPORTANT: The console features a display demo

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as

you plug in the power cord and press the power

switch into the reset position, the demo mode is

turned on. To turn off the demo mode, hold down

the Stop button for a few seconds. If the displays

remain lit, see THE INFORMATION MODE on page

23 to turn off the demo mode.

Next, stand on the foot

rails of the treadmill.

Find the clip attached

to the key (see the

drawing at the right)

and slide the clip onto

the waistband of your

clothes. Then, insert

the key into the console. After a moment, the displays

will light. IMPORTANT: In an emergency situation,

the key can be pulled from the console, causing

the walking belt to slow to a stop. Test the clip by

carefully taking a few steps backward; if the key is

not pulled from the console, adjust the position of

the clip. Note: The first time you insert the key into the

console, the incline will automatically rise to the maxi-

mum incline level and then return to the minimum in-

cline level.

Note: The console can display speed and distance in

either kilometers or miles. To find out which unit of

measurement is selected or to change the unit of mea-

surement, see THE INFORMATION MODE on page

23. For simplicity, all instructions in this section refer to

kilometers.

HOW TO USE THE MANUAL MODE

1. Insert the key into the console.

See HOW TO TURN ON THE POWER at the left.

2. Select the manual mode.

When the key is in-

serted, the manual mode

will be selected and a

track will appear in the

matrix. If a preset work-

out has been

selected, remove the

key and then reinsert it.

3. Start the walking belt.

To start the walking belt, press the Go button, the

Speed increase button, or one of the speed but-

tons numbered 1 through 18.

If you press the Go button or the Speed increase

button, the walking belt will begin to move at 2

Km/H. As you exercise, change the speed of the

walking belt as desired by pressing the Speed in-

crease and decrease buttons. Each time you press

one of the buttons, the speed setting will change

by 0.1 Km/H; if you hold down the button, the

speed setting will change in increments of 0.5

Km/H. Note: After you press the buttons, it may

take a moment for the walking belt to reach the se-

lected speed setting.

If you press one of the numbered speed buttons,

the walking belt will gradually change speed until it

reaches the selected speed setting.

To stop the walking belt, press the Stop button. To

restart the walking belt, press the Go button, the

Speed increase button, or one of the speed but-

tons numbered 1 through 18.

Reset

Key

Clip

4. Change the incline of the treadmill as desired.

To change the incline of

he treadmill, press the

Incline increase and de-

rease buttons or one

of the numbered incline

buttons. Each time you

press the incline increase or decrease button, the

incline will change by 0.5%. If you press one of the

numbered incline buttons, the treadmill will adjust

to the selected incline setting. Note: After you

press the buttons, it may take a moment for the

treadmill to reach the selected incline setting.

5. Monitor your progress with the matrix and the

displays.

The matrix—When the

manual mode is se-

lected, the display will

show a track that repre-

sents 1/4 mile (400 me-

ters). As you exercise,

the indicators around

the track will light in succession until the entire

track is lit. The track will then darken and the indi-

cators will again begin to light in succession.

Time display—When

the manual mode is se-

lected, this display will

show the elapsed time.

When a workout is se-

lected, the display will

show the time remaining in the workout rather than

the elapsed time.

Distance/Incline dis-

play—This display

shows the distance that

ou have walked or run.

This display will also

how the incline setting

for several seconds, each time the incline changes.

Calories/Pulse

display—This display

shows the approximate

number of calories you

have burned. The dis-

play will also show your

heart rate when you use the handgrip pulse sensor

or the volume level when you press the Volume in-

crease or decrease button.

Speed display—This

display shows the speed

of the walking belt.

To reset the displays, press the Stop button, re-

move the key, and then reinsert the key.

6. Measure your heart rate if desired.

Note: If you use the handgrip pulse sensor and

he optional chest pulse sensor at the same

time, the console will not display your heart

ate accurately. For information on the optional

chest pulse sensor, see page 23.

Before using the

handgrip pulse

sensor, first re-

move the sheets

of plastic from

the metal con-

tacts. In addition,

make sure that

your hands are

clean.

To use the handgrip pulse sensor, stand on the

foot rails and hold the metal contacts for at least

ten seconds—avoid moving your hands. When

your pulse is detected, your heart rate will be

shown. For the most accurate heart rate read-

ing, continue to hold the contacts for about 15

seconds.

7. When you are finished exercising, remove the

key from the console.

tep onto the foot rails, press the Stop button, and

adjust the incline of the treadmill to the lowest

etting. The incline must be at the lowest set-

ting or you may damage the treadmill when you

fold it to the storage position. Next, remove the

key from the console and put it in a secure place.

When you are finished using the treadmill, press

the power switch into the off position and unplug

the power cord. IMPORTANT: If you do not do

this, the treadmillʼs electrical components may

wear prematurely.

Contacts

Page is loading ...

NordicTrack T 7.0 Treadmill User manual

Brand: NordicTrack

Model: T 7.0 Treadmill

Category: Treadmills

Type: User manual

This manual is also suitable for

NETL81810.0

Download PDF

report

NordicTrack T 7.0 Treadmill User manual

This manual is also suitable for

NordicTrack T 7.0 Treadmill User manual

Related papers

Other documents