Sprint AIRAVE 2.5+ Setup Instructions

Category
Modems
Type
Setup Instructions

Sprint AIRAVE 2.5+ provides a boosted signal for your wireless voice and 3G data services. It’s like having your very own cell tower. Once the four LED lights (Mobile, Network, GPS, and Broadband) have stopped blinking and are a steady green, your AIRAVE is ready to use. You will hear three short beeps when placing or answering calls on your wireless phone if you are within range of the AIRAVE. Sprint AIRAVE 2.5+ will display solid green lights when it is activated and functioning properly.

Sprint AIRAVE 2.5+ provides a boosted signal for your wireless voice and 3G data services. It’s like having your very own cell tower. Once the four LED lights (Mobile, Network, GPS, and Broadband) have stopped blinking and are a steady green, your AIRAVE is ready to use. You will hear three short beeps when placing or answering calls on your wireless phone if you are within range of the AIRAVE. Sprint AIRAVE 2.5+ will display solid green lights when it is activated and functioning properly.

Mobile
Network
GPS
Broadband
1. Disconnect all power on your
network, including your cable
or DSL modem and router.
2.
Plug one end of the yellow Ethernet cable into your
broadband modem.
3. Connect the other end of the cable into the
yellow WAN port at the back of the AIRAVE.
4. Reconnect power to your cable or DSL
modem and wait about two minutes
for the modem to power up and
initialize.
5. Plug the power supply
connector into the
back of the AIRAVE.
6. Plug the other end of
the power cord into an
available electrical outlet.
READ ME FIRST! Setup Instructions
Check that all these components are in the box:
AIRAVE 2.5+
Printed Materials
Power Cord
Yellow Ethernet Cable
External GPS Antenna Cable
Before You Install Your AIRAVE
Install Your AIRAVE
Note: You will also need a working electrical outlet and a
broadband connection (cable, DSL, etc.) to use this device.
LAN 2
LAN 1
WAN
12VDC
To Broadband
Modem
AIRAVE
LAN 1
WAN
12VDC
to Power
Supply
continued on
other side
2
3
5
6
1
4
The AIRAVE 2.5+ you requested is enclosed. The
AIRAVE
provides a boosted signal for your wireless voice and
3G
data services. It’s like having your very own cell tower.
1.
Follow the diagram below to connect the antenna
to the AIRAVE.
2.
Place the GPS antenna on a flat surface and next to a
closed window, if possible.
Note: It may take up to 30 minutes for the GPS LED light to
become solid green.
Note: In large homes, the external GPS antenna can be used
to allow the AIRAVE to be placed
in a more central location,
allowing for more even coverage
throughout the house.
Connect the External GPS Antenna
AIRAVE Technical Support: 1-866-556-7310
LAN 2
Reset
LAN 1
WAN
12VDC
GPS
Mobile
Network
GPS
Broadband
Place on Window Sill
AIRAVE
GPS Antenna Module
Resources
If your AIRAVE is still not working, you have several
resources that will have you up and running in no time:
In the Box
The Technical and Troubleshooting Guide, with
expanded details.
Online (sprint.com/airave)
FAQs, technical documentation, and more.
The latest User Guide, with detailed instructions
for advanced features.
Phone
AIRAVE Technical Support:
1-866-556-7310
Ready Now Visit sprint.com/readynow for additional
help to get started on your new device. You’ll find more
information on basic setup, activation, maximizing your
device’s performance, etc. Plus, you can even
schedule a personalized one-on-one Ready Now
appointment at a Sprint Store near you.
PC or LAN (local area network) Router: Connect your
PC, your LAN router, or both to the AIRAVE’s LAN ports.
PC or LAN Router Option
LAN 2
Reset
LAN 1
WAN
12VDC
GPS
Check Your Connection
Your AIRAVE’s LED lights will flash as your device
initializes and acquires a GPS lock.
When the Mobile, Network, GPS, and Broadband LED
lights have stopped blinking, your AIRAVE is ready to use.
This process can take up to two hours.
Do not interrupt the process during this time.
Once the four LED lights have stopped blinking and
are a steady green, test your AIRAVE connection:
Dial *99 on any Sprint phone. You should hear
a message that says “You are now within
AIRAVE coverage.”
Note: You will hear three short beeps when placing or
answering calls on your wireless phone if you are within
range of the AIRAVE.
Important: To ensure the best voice and data quality,
always connect the LAN router to your AIRAVE. Do not
connect the router directly to your broadband modem
or other broadband connection device.
WAIT
The AIRAVE will display solid
green lights when it is activated
and functioning properly.
©2013 Sprint. SPRINT and the logo are trademarks of Sprint.
Other marks are property of their respective owners.
912902
READ ME FIRST! Setup Instructions (Continued)
AIRAVE Technical Support: 1-866-556-7310
  • Page 1 1
  • Page 2 2

Sprint AIRAVE 2.5+ Setup Instructions

Category
Modems
Type
Setup Instructions

Sprint AIRAVE 2.5+ provides a boosted signal for your wireless voice and 3G data services. It’s like having your very own cell tower. Once the four LED lights (Mobile, Network, GPS, and Broadband) have stopped blinking and are a steady green, your AIRAVE is ready to use. You will hear three short beeps when placing or answering calls on your wireless phone if you are within range of the AIRAVE. Sprint AIRAVE 2.5+ will display solid green lights when it is activated and functioning properly.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI