EPH Controls R27-RF User manual

Brand
EPH Controls
Model
R27-RF
Type
User manual

EPH Controls R27-RF is a 2 zone RF programmer designed to provide ON/OFF control for 2 zones, with the added application of inbuilt frost protection. It can be mounted directly on the wall or to a recessed conduit box. The device has an IP rating of IP20, meaning it is suitable for use in normal environments. The power supply is 230 Vac, and the contact rating is 250 Vac 3A(1A).

With its frost protection function, the programmer can be set to protect pipes against freezing or to prevent low room temperature when the programmer is programmed to be OFF or is manually OFF.

The programmer has a number of other features, including:

EPH Controls R27-RF is a 2 zone RF programmer designed to provide ON/OFF control for 2 zones, with the added application of inbuilt frost protection. It can be mounted directly on the wall or to a recessed conduit box. The device has an IP rating of IP20, meaning it is suitable for use in normal environments. The power supply is 230 Vac, and the contact rating is 250 Vac 3A(1A).

With its frost protection function, the programmer can be set to protect pipes against freezing or to prevent low room temperature when the programmer is programmed to be OFF or is manually OFF.

The programmer has a number of other features, including:

For use in normal environments.
R27-RF - 2 Zone RF Programmer Installation Instructions
Page 1 of 2
Before commencing any work on the electrical connections, you must rst disconnect the programmer
from the mains. None of the 230V connections must be live until the installation has been completed and
the housing is closed. Only qualied electricians or authorised service sta are permitted to open the
programmer. Disconnect from mains supply in the event of any damage to any buttons.
There are parts that carry mains voltage behind the cover. The programmer must not be left unsupervised
when open. (Prevent non specialists and especially children from gaining access to it.)
If the programmer is used in a way not specied by the manufacturer, its safety may be impaired.
Ensure that this wireless enabled programmer is installed 1 metre from any metalic object, television, radio
or wireless internet transmitter.
Prior to setting the programmer, it is neccessary to complete all required settings described in this section.
Never remove this product from the electrical baseplate. Do not use sharp tools to push any button.
CAUTION! Installation and connection should only be carried out by a qualied
person and in accordance with national wiring regulations.
This programmer can be mounted in the following ways: 1. Directly wall mounted 2. Mounted to a recessed conduit box
This 2 zone RF programmer is designed to provide
ON/OFF control for 2 zones, with the value added
application of in built frost protection.
Important: Keep this document
1
34
5 6
2
Type
EN60730
1C IP20
EN60529
50
°C
0
122
°F
32
5-95%RH
160.5
100
20221019_R27-RF_InsIns_PK
EPH Controls Ireland
technical@ephcontrols.com www.ephcontrols.com
EPH Controls UK
technical@ephcontrols.com www.ephcontrols.co.uk
For use in normal environments.
R27-RF - 2 Zone RF Programmer Installation Instructions
Page 2 of 2
1. Factory default settings
Contacts: 230 Volt
Program: 5/2D
Backlight: On
Keypad: Unlocked
Frost Protection: O
Clock type: 24 Hr Clock
Day-Light Saving
Power Supply: 230 Vac
Ambient Temp: 0~35°C
Contact Rating: 250 Vac 3A(1A)
Program Memory
backup: 1 year
Battery: 3Vdc Lithium LIR 2032
Backlight: Blue
IP rating: IP20
Backplate: British System Standard
Pollution degree 2: Resistance to voltage surge 2000V
as per EN 60730
Automatic Action: Type 1.S
Software: Class A
2. Specications & wiring
Lower the cover on the front of the programmer. There are four hinges
holding the cover in place.
Between the 3rd and 4th hinges there is a circular hole. Insert a ball point
pen or similar object to master reset the programmer.
After pressing the master reset button, the date and time will now need to
be reprogrammed.
5. Master reset
Contents
1. Factory default settings
2. Specications & wiring
3. Setting the date & time
4. Frost protection
5. Master reset
3. Setting the date and time
Press
Press
Press
Press
Press
Press
Lower the cover on the front of the programmer.
Move the selector switch to the CLOCK SET position.
Press the or buttons to select the day.
Press the or buttons to select the month.
Press the or buttons to select the year.
Press the or buttons to select the hour.
Press the or buttons to select the minute.
Press the or buttons to select 5/2D, 7D or 24H
The date, time and function are now set. Move the selector switch to the
RUN position to run the program, or to the PROG SET position to change
the program setting.
Selectable range 5~20°C
This function is set to protect pipes against freezing or to prevent low room
temperature when the programmer is programmed to be OFF or is manually
OFF.
Frost protection can be activated by following the procedure below.
Move the selector switch to the RUN position.
Press both the and buttons for 5 seconds, to enter selection mode.
Press either the or buttons to to turn On or turn O frost protection.
Press button to conrm
Press either the or buttons to increase or decrease the desired frost
protection setpoint.
Press to select.
All zones will be switched ON in the event of room temperature falling below
the frost protection setpoint.
O
4. Frost protection function
RUN
CLOCK
SET
PROG
SET
200-240Vac
50Hz-60Hz CONTACT RATING: 250Vac~/3(1)A
Z1
OFF
Z2
OFF
Z2
ON
Z1
ON
20221019_R27-RF_InsIns_PK
EPH Controls Ireland
technical@ephcontrols.com www.ephcontrols.com
EPH Controls UK
technical@ephcontrols.com www.ephcontrols.co.uk
  • Page 1 1
  • Page 2 2

EPH Controls R27-RF User manual

Brand
EPH Controls
Model
R27-RF
Type
User manual

EPH Controls R27-RF is a 2 zone RF programmer designed to provide ON/OFF control for 2 zones, with the added application of inbuilt frost protection. It can be mounted directly on the wall or to a recessed conduit box. The device has an IP rating of IP20, meaning it is suitable for use in normal environments. The power supply is 230 Vac, and the contact rating is 250 Vac 3A(1A).

With its frost protection function, the programmer can be set to protect pipes against freezing or to prevent low room temperature when the programmer is programmed to be OFF or is manually OFF.

The programmer has a number of other features, including:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents