Simpson ALH3228 User manual

Brand: Simpson

Model: ALH3228

Category: High-pressure cleaners

Type: User manual

Simpson ALH3228 pressure washer delivers a powerful 3200 PSI and 2.8 GPM to tackle your toughest cleaning challenges. Blast away dirt, grime, and mildew from decks, patios, driveways, and more. With its compact size and lightweight design, the ALH3228 is easy to maneuver around your property. The included turbo nozzle amplifies cleaning power for stubborn stains and grease.

Part No. 7107725 Rev. 1 MAR 2016

3200 PSI

2.8 GPM

PREMIUM PRESSURE WASHER

INSTRUCTION

MANUAL

MANUEL

D’UTILISATION

MANUAL DE

INSTRUCCIONES

MODEL

MODèLE

MODELO

ALH3228

If your pressure washer is not working properly or if there are parts missing or broken,

please DO NOT RETURN IT TO THE PLACE OF PURCHASE. Contact our Customer

Service Department at 1-877-362-4271 or www.simpsoncleaning.com

Si votre rondelle de pression ne travaille pas convenablement ou s'il y a des

parties manquant ou cassé, s'il vous plaît le PAS LE RETOURNE AU LIEU

D'ACHAT. Contacter notre département de service clients à 1-877-362-4271 o

www.simpsoncleaning.com

Si su lavadora a presión no trabaja correctamente ó encuentra partes rotas

ófaltantes, por favor NO LA REGRECE AL LUGAR DONDE LA COMPRO.

Contáctese con nuestro Departamento de Servicio al Cliente llamando al

1-877-362-4271 ou www.simpsoncleaning.com

IMPORTANT: Please make certain that the person who is to use this equipment carefully

reads and understands these instructions before operating.

IMPORTANT : Assurez-vous que toute personne qui utilisera cet équipement lise

attentivement ces instructions avant de l’utiliser.

IMPORTANTE: Aségurese por favor de que la persona que vaya a utilizar este equipo lea

con cuidado y comprenda estas instrucciones antes de operar.

VEA EL ESPAÑOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACIÓN,

CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Save thiS manual for future reference

liSeZ et conServeZ ceS inStructionS

conServe eStaS inStruccioneS Para futuraS conSultaS

2- ENG

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand.

This information relates to protecting YOUR SAFETY and PREVENTING

EQUIPMENT PROBLEMS. To help you recognize this information, we use the

symbols below. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided,

may result in property damage.

IMpORTANT SAFETY INSTRUCTIONS

DANGER: Carbon Monoxide. Using an engine indoors can kill you in

minutes. Engine exhaust contains high levels of carbon monoxide (CO), a

poisonous gas you cannot see or smell. You may be breathing CO even if you

do not smell engine exhaust.

•NEVER use an engine inside homes, garages, crawlspaces or other partly

enclosed areas. Deadly levels of carbon monoxide can build up in these areas.

Usingafanoropeningwindowsanddoorsdoes NOTsupplyenoughfreshair.

•ONLY useoutdoorsand farawayfrom openwindows,doors andvents.These

openingscanpullinengineexhaust.

• Evenwhentheengineisusedcorrectly,COmayleakintoyourhome.ALWAYS use

abattery-poweredorbatterybackupCOalarminyourhouse.Read and follow all

directions for CO alarm before using. Ifyoufeelsick,dizzyorweakatanytime,

move to fresh air immediately. See a doctor. You could have carbon monoxide

poisoning.

WARNING: Do not operate this unit until you read this instruction manual and

the engine instruction manual for safety, operation and maintenance instructions. If

you have any questions regarding the product, please contact our customer

service department at www.simpsoncleaning.com.

DANGER: Risk of injection or severe injury. Keep clear of nozzle. Do not

direct discharge stream at persons or live animals. This product is to be used

only by trained operators.

WARNING: This product and its exhaust contain chemicals known to the State

of California to cause cancer, birth defects or other reproductive harm. In addition,

some cleaning products and dust contain chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm. Wash hands

after handling.

3 - ENG

WARNING: This product may not be equipped with a spark-arresting muffler.

If the product is not equipped and will be used around flam ma ble ma teri als or

on land covered with materials such as agricultural crops, forest, brush, grass or

other similar items, then an ap proved spark arrester must be installed and is legally

required in the state of California. It is a violation of California statutes section

130050 and/or sec tions 4442 and 4443 of the California Public Re sourc es Code,

unless the engine is equipped with a spark arrester, as defined in section 4442, and

maintained in ef fec tive work ing order. Spark arresters are also required on some

U.S. For est Service land and may also be legally required under other statutes and

or di nanc es.

Save theSe inStructionS

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spilled gasoline and it’s vapors can

becomeignitedfromcigarettesparks,

electrical arcing, exhaust gases and

hotengine componentssuchas the

muffler.

• Shutoffengineandallowittocoolbefore

addingfueltothetank.

• Usecareinfillingtanktoavoidspillingfuel.

Movepressurewasherawayfromfueling

areabeforestartingengine.

• Heatwillexpandfuelinthetankwhich

could result in spillage and possible

fireexplosion.

• Keepmaximumfuellevel1/2"(12.7mm)

below bottom of filler neck to allow for

expansion.

• Operatingthepressurewasherinan

explosiveenvironmentcouldresultin

afire.

• Operate and fuel equipment in well-

ventilated areas free from obstructions.

Equipareaswithfireextinguishersuitable

forgasolinefires.

• Materials placed against or near the

pressure washer can interfere with

itsproperventilationfeaturescausing

overheating and possible ignition of

thematerials.

• Neveroperatepressurewasherinanarea

containingdrybrushorweeds.

• Muffler exhaust heat can damage

painted surfaces, melt any material

sensitive to heat (such as siding,

plastic, rubber, vinyl or the pressure

hose,itself),anddamageliveplants.

• Alwayskeeppressurewasheraminimum

of4'(1.2m)awayfromsurfaces(suchas

houses, automobiles or live plants) that

could be damaged from muffler exhaust

heat.

• Improperly stored fuel could lead to

accidental ignition. Fuel improperly

secured could get into the hands of

childrenorotherunqualifiedpersons.

• StorefuelinanOSHAapprovedcontain-

er, in a secure location away from work

area.

• Use of acids, toxic or corrosive

chemicals, poisons, insecticides, or

any kind of flammable solvent with

this product could result in serious

injuryordeath.

• Donotsprayflammableliquids.

4- ENG

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Breathing exhaust fumes will cause

serious injury or death! Engine

exhaust contains carbon monoxide,

anodorlessanddeadlygas.

• Operate pressure washer in a well-

ventilated area. Avoid enclosed areas

suchasgarages,basements,etc.

• Never operate unit in or near a location

occupiedbyhumansoranimals.

• Some cleaning fluids contain

substanceswhichcouldcauseinjury

toskin,eyesorlungs.

• Use only cleaning fluids specifically rec-

ommended for high pressure washers.

Follow manufacturersrecommendations.

Donot usechlorine bleachor anyother

corrosivecompound.

DANGER: RISK OF FLUID INJECTION AND LACERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Yourpressurewasheroperatesatfluid

pressuresandvelocitieshighenough

topenetratehuman andanimalflesh

which could result in amputation or

other serious injury. Leaks caused

byloosefittingsorwornordamaged

hoses can result in injection injuries.

DO NOT TREAT FLUID INJECTION

ASA SIMPLE CUT!See a physician

immediately!

• Inspect the high pressure hose regularly.

Replace the hose immediately if it is

damaged, worn, has melted from

contactingtheengine,orshowsanysigns

of cracks, bubbles, pinholes, or other

leakage. Never grasp a high pressure

hosethatisleakingordamaged.

• Nevertouch,grasporattempttocovera

pinhole or similar water leak on the high

pressure hose. The stream of water IS

underhigh pressure andWILL penetrate

skin.

• Neverplacehandsinfrontofnozzle.

• Directsprayawayfromselfandothers.

• Makesurehoseandfittingsaretightened

and in good condition. Never hold onto

thehoseorfittingsduringoperation.

• Donotallowhosetocontactmuffler.

• Never attach or remove wand or hose

fittingswhilesystemispressurized.

• Whenusingreplacementlancesorguns

with this pressure washer, DO NOT use

a lance and/or lance/gun combination

that is shorter in length than what was

provided with this pressure washer as

measured from the nozzle end of the

lancetotheguntrigger.

• Injuriescanresult ifsystempressure

is not reduced before attempting

maintenanceordisassembly.

• To relieve system pressure, shut off

engine,turnoffwatersupplyandpullgun

triggeruntilwaterstopsflowing.

• Use only accessories rated equal to or

higher than the rating of the pressure

washer.

5 - ENG

DANGER: RISK OF INJURY FROM SPRAY

WHAT CAN HAPPEN HOW TO PREVENT IT

• High-velocity fluid spray can cause

objectstobreak, projecting particles

athighspeed.

• Always wear ANSI-approved Z87.1

safety glasses. Wear protective clothing

toprotectagainstaccidentalspraying.

• Never point wand at or spray people or

animals.

• Light or unsecured objects can

becomehazardousprojectiles. • Always secure trigger lock when wand

is not in service to prevent accidental

operation.

• Neverpermanentlysecuretriggerinpull-

back(open)position.

DANGER: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe operation of your pressure

washercouldleadtoseriousinjuryor

deathtoyouorothers.

• Donot usechlorine bleachor anyother

corrosivecompound.

• Become familiar with the operation and

controlsofthepressurewasher.

• Keepoperatingareaclearofallpersons,

petsandobstacles.

• Donotoperatetheproductwhenfatigued

orundertheinfluenceofalcoholordrugs.

Stayalertatalltimes.

• Nevercompromisethesafetyfeaturesof

thisproduct.

• Do not operate machine with missing,

brokenorunauthorizedparts.

• Neverleavewandunattendedwhileunitis

running.

• If proper starting procedure is not

followed,enginecankickbackcausing

serioushandandarminjury.

• If engine does not start after two pulls,

squeeze trigger of gun to relieve pump

pressure. Pull starter cord slowly until

resistanceisfelt.Thenpullcordrapidlyto

avoidkickbackandpreventhandorarm

injury.

• The spray gun/wand is a powerful

cleaningtoolthatcouldlooklikeatoy

toachild.

• Keep children away from the pressure

washeratalltimes.

• Reactiveforceofspraywillcausegun/

wand to kickback, and could cause

theoperatortosliporfallormisdirect

the spray. Improper control of gun/

wandcanresultininjuriestoselfand

others.

• Donotoverreachorstandonanunstable

support.

• Do not use pressure washer while

standingonaladder.

• Grip gun/wand firmly with both hands.

Expect the gun to kickback when

triggered.

6- ENG

DANGER: RISK OF INJURY OR PROP ER TY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Fueloroilcanleakorspillandcould

result in fire or breathing hazard.

Serious injury or death can result.

Fuel or oil leaks will damage carpet,

paintorothersurfacesinvehiclesor

trailers.

• Oilcouldfillthecylinderanddamage

theengineiftheunitisnotstoredor

transportedinanuprightposition.

• Ifpressurewasherisequippedwithafuel

shut-off valve, turn the valve to the OFF

positionbeforetransportingtoavoidfuel

leaks.Ifpressurewasherisnotequipped

with a fuel shut-off valve, drain the fuel

fromtankbeforetransporting.Onlytrans-

portfuelinanOSHA-approvedcontainer.

 Always place pressure washer on a

protective mat when transporting to

protect against damage to vehicle from

leaks.

 Always transport and store unit in an

upright position. Remove pressure

washer from vehicle immediately upon

arrivalatyourdestination.

DANGER: RISK OF ELEC TRI CAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spray directed at electrical outlets or

switches,orobjectsconnectedtoan

electricalcircuit,couldresultinafatal

electricalshock.

• Unpluganyelectricallyoperated product

beforeattemptingtocleanit.Directspray

awayfromelectricoutletsandswitches.

DANGER: RISK OF CHEMICAL BURN

WHAT CAN HAPPEN HOW TO PREVENT IT

• Use of acids, toxic or corrosive

chemicals, poisons, insecticides, or

anykindofflammablesolventwiththis

productcouldresultinseriousinjuryor

death.

• Do not spray acids, gasoline, kerosene,

oranyotherflammablematerialswiththis

product.Useonlyhouseholddetergents,

cleaners and degreasers recommended

forusewithpressurewashers.

• Wear protective clothing to protect

eyes and skin from contact with sprayed

materials.

7 - ENG

WARNING: RISK OF BURSTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Over inflation of tires could result in

seriousinjuryandpropertydamage.

• Use a tire pressure gauge to check the

tires pressure before each use and while

inflating tires; see the tire sidewall for the

correcttirepressure.

NOTE:

Airtanks,compressorsandsimilar

equipmentusedtoinflatetirescanfillsmall

tires similar to these very rapidly. Adjust

pressureregulatoronairsupplytonomore

thantheratingofthetirepressure.Addair

insmallincrementsandfrequentlyusethe

tiregaugetopreventoverinflation.

• High-velocity fluid spray directed at

pneumatic tire sidewalls (such as

found on automobiles, trailers and

the like) could damage the sidewall

resultinginseriousinjury.

• On pressure washers rated above

1600 PSI (11032 kPa) use the widest

fan spray (40ºnozzle) and keep the

sprayaminimumof8"(20cm)fromthe

pneumatictiresidewall.Donotaimspray

directlyat the jointbetween thetire and

rim.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Contact with hot surfaces, such as

engine exhaust components, could

resultinseriousburn.

• During operation, touch only the control

surfaces of the pressure washer. Keep

childrenaway fromthe pressure washer

at all times. They may not be able to

recognizethehazardsofthisproduct.

WARNING: RISK OF INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Serious injury can result from

attemptingtolifttooheavyanobject. • The pressurewasher istoo heavyto be

lifted by one person. Obtain assistance

fromothersbeforelifting.

Save theSe inStructionS

for future uSe

8- ENG

qUICk SETUp GUIDE

WARNING: To reduce the risk of injury, read the pressure washer instruction manual and

the engine instruction manual before operating pressure washer.

aInstall the Handle

Slide the handle

assembly onto

the frame and secure with

saddle bolts and knobs.

BAdd/Check Oil

The engine is

shipped without

oil. Before starting engine,

add the oil provided.

Check oil level prior to

each use. Refer to Engine

Owner’s Manual for

complete procedure.

cAdd Gasoline

In a well ventilated

outdoor area

add fresh, high quality,

unleaded gasoline with a

pump octane rating of 86

or higher. Do not overfill.

Wipe up spilled fuel before

starting the engine. Refer to

Engine Owner's Manual

for complete procedure.

qUICk START GUIDE

DANGER:

• Neverrunengineindoorsorinenclosed,poorlyventilatedareas.Engineexhaustcon-

tains carbon monoxide, an odorless and deadly gas.

• Riskoffluidinjectionandlaceration.Whenusingthehigh-pressuresetting,DONOT

allow the high-pressure spray to come in contact with unprotected skin, eyes or with

any pets or animals. Serious injury will occur.

1Connect Garden

Hose to Pump

Thread the garden

hose to the pump inlet.

See label #1 on unit.

2Connect High

Pressure Hose to

Pump

Connect the high pressure

hose to the pump outlet.

See label #2 on unit.

3Connect High

Pressure Hose to

Spray Gun

Connect the other end

of the high pressure

hose to the spray gun.

9 - ENG

4Connect Spray

Wand to Spray

Gun

Thread the spray wand into

the end of the spray gun.

5Connect QC

Nozzles to Spray

Wand

Pull quick connect

coupler back and insert

nozzle. Release quick

connect coupler and

twist nozzle to make sure

it is secure in coupler.

6Turn Water

Faucet

Completely On

Do not run the unit

without water supply

connected and turned on.

Use Cold Water Only.

7Release Air from

System

Release all air from

pump and high pressure

hose by depressing

trigger until a steady

stream of water is present.

Approximately 30 seconds.

30 S

8Verify the Fuel

Switch is in the

ON Position

See label #8 on unit.

9Verify the Engine

Switch is turned

to the ON

Position

See label #9 on unit.

OFF

10 Move the Choke to

the CLOSED Position

See label #10 on unit.

WARNING: This Guide is not a substitute for reading the operator's manual. User must

read and understand operator's manual before using this product.

11 Pull the

Recoil Starter

Grip

Pull the recoil

starter grip to start

the engine.

See label #11 on unit.

12 Move the

Choke to the

OPEN Position

Gradually move

the Choke to the

OPEN Position after

engine starts.

See label #12 on unit.

10- ENG

GET TO kNOW THE pRESSURE WASHER

NOTE: Photographs and line drawings used in this manual are for reference

only and do not represent a specific model.

Compare the illustrations with your unit to familiarize yourself with the location of

various controls and adjustments. Save this manual for future reference.

BASIC ELEMENTS OF A pRESSURE WASHER (FIG. 1)

A. High Pressure Pump: Increases the pressure of the water supply.

B. Engine: Drives the high pressure pump. Refer to the Engine Owner's Manual

for location and operation of engine controls.

C. High Pressure Hose: Carries the pressurized water from the pump to the gun

and spray wand.

D. Spray Gun: Connects with spray wand to control water flow rate, direction and

pressure.

E. Quick-Connect Spray Wand: Allows the user to quickly change out high

pressure nozzles. See How To Use Spray Wand instructions in Operation

section.

F. Detergent Siphon Hose (not shown): Feeds cleaning agents into the pump to mix

with the water. See

How To Apply Chemicals/Cleaning Solvents

instructions

Operation

section.

G. Handle

11 - ENG

H. Frame

I. Pump Outlet

J. Pump Inlet

K. Quick Connect Nozzles

L. Nozzle Holder

BASIC ELEMENTS OF AN ENGINE

Refer to the Engine Owner's Manual for location and operation of engine controls.

Choke Control: Opens and closes carburetor choke valve.

Starter Grip: Pulling starter grip operates recoil starter to crank engine.

Engine Switch: Enables and disables ignition system.

ASSEMBLY INSTRUCTIONS (FIG. 2–4)

1. Locate and remove all loose parts from the carton.

2. Cut four corners of the carton from top to bottom and lay the panels flat.

Slide the handle assembly (G) onto

22A K

the frame (H) and secure with saddle

bolts and knobs.

NOTICE: Risk of personal injury. Avoid

placing hands between handle and frame

when assembling to prevent pinching.

4. Remove colored quick connect

nozzles (K) from plastic bag and insert them into the nozzle holder (L).

NOTE: Nozzles are color coded to match colored nozzles on panel.

5. Connect wand (E) to gun (D). Tighten securely.

6. Attach high pressure hose (C) to gun (D). Tighten se cure ly.

NOTICE: The engine is shipped without oil. Before starting engine, add the oil

provided. Damage to the engine will occur if the engine is run without oil, this

damage will not be covered under warranty.

NOTICE: The high-pressure pump was filled with oil at the factory. Always check

oil level before using (refer to Maintenance for more information).

12- ENG

OpERATION

pRESSURE WASHER TERMINOLOGY

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used

for air pressure, hydraulic pressure, etc.

GPM: Gallons Per Minute. The unit of measure for the flow rate of water.

CU: Cleaning Units. GPM multiplied by PSI equals CU.

Bypass Mode: Allows water to re-circulate within the pump when the gun trigger is

not pulled. This feature allows the operator to release the trigger gun and reposition

themselves without having to turn the engine off in between cleaning actions.

NOTICE: Allowing the unit to run for more than two minutes without the gun trigger

being pulled could cause overheating and damage to the pump. Do not let the

pressure washer run for more than two minutes in Bypass Mode. Turn off the engine

and relieve the pressure in the gun during these extended situations.

Thermal Relief Valve (Q, Fig. 5): When the temperature inside the 5

pump rises too high, this valve will open and release a gush of

water in an effort to lower the temperature inside the pump. The

valve will then close.

Detergent Injection System: Mixes cleaners or cleaning solvents

with the water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water.

The minimum requirements for a water supply are 20 PSI and 5 Gallons Per Minute.

If your water source is a well, the garden hose length can only be 30ft. (9m) max.

WARNING: To reduce the possibility of contamination always protect

against backflow when connected to a potable water system.

pRESSURE WASHER OpERATING FEATURES

pRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve op ti mum pres sure and

cleaning. If you need to lower the pres sure, it can be accomplished by these meth-

ods.

1. Back away from the sur face to be cleaned. The further away you are, the

less the pressure will be on the surface to be cleaned.

2. Change to the 40˚ nozzle (white). This nozzle delivers a less powerful stream

of water and a wider spray pattern. Refer to How To Use Spray Wand.

NOTICE: DO NOT attempt to increase pump pressure. A higher pressure setting

than the factory set pressure may damage pump.

HOW TO USE SpRAY WAND

The nozzles for the spray wand are stored in the nozzle holder on the panel assembly.

Colors on the panel identify nozzle spray pattern. Refer to the following chart to

choose the correct nozzle for the job to be performed.

13 - ENG

NOzzLE COLOR SpRAY pATTERN USES SURFACES*

Red

0˚ powerful pinpoint

for spot cleaning

of hard, unpainted

surfaces or for

high reach areas

unpainted metal

or concrete;

DO NOT use on wood

Yellow

15˚ intense cleaning

of unpainted

hard surfaces

grills, driveways, concrete

or brick walkways,

unpainted brick or stucco

Green

25˚ standard cleaning

nozzle for most

applications

yard tools, sidewalks,

lawn furniture, unpainted

siding, stucco, gutters

and eaves, concrete,

brick surfaces

White

40˚ cleaning of painted

or delicate surfaces auto/RV, marine, wood,

painted brick and stucco,

vinyl, painted siding

Black

low pressure applies cleaning

solutions Low pressure

spray is safe on all

surfaces. Always verify

compatibility of cleaning

solution prior to use.

*NOTICE: The high pressure spray from your pressure washer is capable of

causing damage to surfaces such as wood, glass, automobile paint, auto striping

and trim, and delicate objects such as flowers and shrubs. Before spraying, check

the item to be cleaned to assure yourself that it is strong enough to resist damage

from the force of the spray.

CHANGING NOzzLES ON SpRAY WAND (FIG. 6)

DANGER: Risk of fluid injection. Do not direct discharge stream toward

persons, unprotected skin, eyes or any pets or animals. Serious injury will

occur.

WARNING: Flying objects could cause risk of serious injury. Do not

attempt to change nozzles while pressure washer is running. Turn engine off

before changing nozzles.

1. Pull quick-connect coupler (E) back and insert nozzle (K). 6

2. Release quick-connect coupler and twist nozzle to

make sure it is secure in coupler.

WARNING: Flying object could cause risk of serious

injury. Ensure nozzle is completely inserted in quick-

connect socket and quick-connect collar is fully engaged

(forward) before squeezing gun trigger.

14- ENG

HOW TO AppLY CHEMICALS/CLEANING SOLvENTS (FIG. 7)

Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use

only soaps and chemicals designed for pressure washer use. Do not use bleach.

To Apply Chemicals:

1. Ensure detergent siphon hose (F, Figure 9) is attached

to barbed fitting location near high pressure hose

connection of pump as shown.

2. Place other end of detergent siphon hose with

filter on it into container holding chemical/cleaning

solution. NOTE: For every 7 gallons of water pumped

1 gallon of chemical/cleaning solution will be used.

3. Install low pressure (black) nozzle into quick connect fitting of spray wand, see

How To Use Spray Wand paragraph in this section.

4. After use of chemicals, place detergent siphon hose into container of clean

water and draw clean water through chemical injection system to rinse system

thoroughly. If chemicals remain in the pump, it could be damaged. Pumps

damaged due to chemical residue will not be covered under warranty.

NOTE: Chemicals and soaps will not siphon if the black soap nozzle is not installed

on the spray wand.

STARTING (FIG. 8–11)

WARNING: To reduce the risk of injury, read the pressure washer instruction

manual and the engine instruction manual before starting pressure washer.

DANGER: Risk of fluid injection and laceration. When using the high

pressure setting, DO NOT allow the high pressure spray to come in contact

with unprotected skin, eyes, or with any pets or animals. Serious injury will

occur.

• Yourwasheroperates atfluidpressuresandvelocitieshigh enoughtopenetrate

humanandanimalflesh,whichcouldresultinamputationorotherseriousinjury.

Leakscausedbyloosefittingsorwornordamagedhosescanresultininjection

injuries.DONOTTREATFLUIDINJECTIONASASIMPLECUT!Seeaphysician

immediately!

DANGER: Carbon Monoxide. Using an engine indoors can kill you in

minutes. Engine exhaust contains high levels of carbon monoxide (CO), a

poisonous gas you cannot see or smell. You may be breathing CO even if you

do not smell engine exhaust.

• Breathingexhaustfumeswillcauseseriousinjuryordeath!Engineexhaust

contains carbon mon ox ide, an odorless and deadly gas.

• Operate pressure washer in a well-ventilated area. Avoid enclosed areas

such as ga rages, base ments, etc.

• Neveroperateunitinornearalocationoccupiedbyhumansoranimals.

WARNING: Risk of Fire, Asphyxiation and Burn. Never fill fuel tank when

engine is running or hot. Do not smoke when filling fuel tank.

• Never fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below bottom of filler

necktoprovidespaceforfuelexpansion.Wipeanyfuelspillagefromengineand

equipmentbeforestartingengine.

• DO NOT let hoses come in contact with very hot engine muffler during or

immediatelyafteruseofyourpressurewasher.Damagetohosesfromcontactwith

hotenginesurfaceswillNOTbecoveredbywarranty.

15 - ENG

NOTICE: Riskofpropertydamage.Neverpullwatersupplyhosetomovepressure

washer. This could damage hose and/or pump inlet.

• DONOTusehotwater,usecoldwateronly.

• Neverturnwatersupplyoffwhilepressurewasherengineisrunningordamageto

pumpwillresult.

• DONOTstopsprayingwaterformorethantwominutesatatime.Pumpoperates

inbypassmodewhensprayguntriggerisnotpressed.Ifpumpisleftinbypass

mode for more than two minutes internal components of the pump can be

damaged.

If you do not understand these precautions, please contact our customer service

department at www.simpsoncleaning.com

Prior to starting, refer to your engine manual for proper starting procedure.

1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline

with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled

fuel before starting the engine. Refer to Engine Owner's Manual for correct

procedure.

NOTICE: Useoffuelswithgreaterthan10%ethanolare

notapprovedforuseinthisproductperEPAregulations

andwilldamagetheunitandvoidthewarranty.

2. Check engine oil level. Refer to Engine Owner's Manual for correct procedure.

3. Check pump oil level. The oil level should come to the dot in the middle of the

sight glass. Refer to the Pump paragraph under Maintenance.

4. Connect the water hose to the water source. Turn the water source on to

remove all air from the hose. When a steady stream of water is present, turn

the water source off.

5. Verify the filter screen (O) is in water inlet of pump. NOTE: Convex side faces

out.

6. Connect water source (N) to pump inlet (J). NOTE: Water source must provide

a minimum of 5 gallons per minute at 20 PSI.

7. Connect

high pressure hose (C) to pump outlet (I).

WARNING: To reduce the possibility of contamination always protect

against backflow when connected to a potable water system.

8. Choose the correct nozzle for the job to be performed. See How To Use spray

Wand instructions in this section. NOTE: If applying a chemical or cleaning

solution, see How To Apply Chemicals/Cleaning Solvents instructions in this

section.

9. Turn water source on.

NOTICE: Risk of property damage. Failure to do so could cause damage to the

pump.

10. Remove all air from the pump and high pressure hose by depressing trigger

until a steady stream of water is present.

16- ENG

11. Start engine. See Engine Owner's Manual for correct procedure.

WARNING: Risk of unsafe operation. If engine does not start after two

pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly

until resistance is felt. Then pull cord rapidly to avoid kickback and prevent

hand or arm injury.

NOTE: If the oil level in the engine is low, the engine will not start. If the engine does

not start, check the oil level and add oil as needed.

12. Depress trigger on gun to start water flow.

WARNING: Risk of unsafe operation. Stand on a stable surface and

grip gun/spray wand firmly with both hands. Expect the gun to kick when

triggered.

13. Release trigger to stop water flow.

WARNING: Risk of injury from spray. Always engage 11

the trigger lock (P) when gun is not in use. Failure to do so

could cause accidental spraying.

SHUTTING DOWN

1. After each use, if you have applied chemicals, place

detergent siphon hose into container of clean water and

draw clean water through chemical injection system to

rinse system thoroughly.

NOTICE: Risk of property damage. Failure to do so could cause damage to the

pump.

2. Turn engine off. See Engine Owner's Manual.

NOTICE: Risk of property damage. NEVER turn the water off with the engine

running.

3. Turn water source off.

4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

NOTE: Failure to release system pressure will prevent removal of high pressure

hose from spray gun or pump connection.

5. See Storage section in this manual for proper storage procedures.

MAINTENANCE

WARNING: Risk of burn hazard. When performing maintenance, you may

be exposed to hot surfaces, water pressure or moving parts that can cause

serious injury or death.

WARNING: Risk of fire hazard. Always disconnect, spark plug wire,

let the engine cool and release all water pressure before performing any

maintenance or repair. The engine contains flammable fuel. Do not smoke or

work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer, a routine

maintenance schedule should be prepared and followed. If the pressure washer is

used in unusual conditions, such as high-temperatures or dusty conditions, more

fre quent maintenance checks will be required.

ENGINE

Consult the Engine Owner's Manual for the man u fac tur er's recommendations

for any and all maintenance. NOTE: The engine drain plug is located at the rear of

the unit.

17 - ENG

pUMp (FIG. 12)

NOTE: The Pump was filled with oil at the factory. The preferred oil is SIMPSON®

Premium Pump Crankcase Oil. If this oil is not available, an SAE 15W-40 oil may

be used. Change the pump oil after the first 50hours of operation and every 100

hours thereafter, or every 3 months.

TO CHECk OIL

The oil level should come to the dot in the middle of 12 BB AA

the sight glass (AA).

HOW TO CHANGE pUMp OIL

1. Loosen pump oil fill plug (BB).

2. Place a container under the pump oil drain plug

(CC).

3. Remove pump oil drain plug.

4. After oil is drained, replace pump oil drain plug. Tighten securely.

5. Refill pump using SIMPSON® Premium Pump Crankcase Oil. If this oil is not

available, an SAE 15W-40 oil may be used.

6. Replace pump oil fill plug and tighten securely.

If there is a problem with the pump contact us at www.simpsoncleaning.com

CONNECTIONS

Connections on pressure washer hoses, gun and spray wand should be cleaned

regularly and lubricated with light oil or lithium grease to prevent leakage and

damage to the o-rings.

NOzzLE CLEANING (FIG. 13)

If the nozzle becomes clogged with foreign materials, such as dirt, excessive

pressure may develop. If the nozzle becomes partially clogged or restricted, the

pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit

supplied and the following instructions:

1. Shut off the pressure washer and turn off the water supply.

2. Pull trigger on gun handle to relieve any water pressure.

3. Disconnect the spray wand from the gun.

4. Remove the high pressure nozzle (K) from the spray 13 K

wand. Remove any obstructions with the nozzle cleaning

tool provided and backflush with clean water.

5. Direct water supply (N) into nozzle to backflush loosened

particles for 30 seconds.

6. Reassemble the nozzle to the wand.

7. Reconnect spray wand to gun and turn on water supply.

8. Start pressure washer and place spray wand into high

pressure setting to test.

CLEAN THE WATER INLET FILTER (FIG. 8)

This screen filter should be checked periodically and cleaned if necessary.

1. Remove filter by grasping end and removing it from water inlet of pump.

2. Clean filter by flushing it with water on both sides.

3. Re-insert filter into water inlet of pump. NOTE: Convex side faces out.

NOTE: Do not operate the pressure washer without filter properly installed.

18- ENG

STORAGE

ENGINE

Consult the Engine Owner's Manual for manufacturer’s recommendations for

storage.

PUMP

The manufacturer recommends using SIMPSON® / POWERWASHER® Pump

Guard or equivalent when storing the unit for more than 30 days and/or when

freezing temperatures are expected. SIMPSON® / POWERWASHER® Pump Guard

is environmentally friendly.

NOTE: Using pump guard helps provide proper lubrication to the internal seals of

the pump regardless of temperature or environment.

NOTICE: Risk of property damage. Use only SIMPSON® / POWERWASHER®

PumpGuardorequivalent.Otherproductscouldbecorrosiveand/orcontainalco-

hol which may cause pump damage.

pRESSURE WASHER

1. Drain all water from high pressure hose and wrap it onto hose wrap.

2. Drain all water from the spray gun and wand by holding spray gun in a vertical

position with nozzle end pointing down and squeezing trigger. Store in gun

holder.

3. Wrap up and secure detergent siphon hose so it is protected from damage.

ACCESSORIES

DANGER: Risk of fluid injection. When using replacement spray wands or

guns with this pressure washer, DO NOT use a spray wand and/or spray gun/

wand combination that is shorter in length than what was provided with this

pressure washer as measured from the nozzle end of the wand to the gun

trigger.

NOTICE: The use of any other accessory not recommended for use with this tool

could be hazardous. Use only accessories rated equal to or greater than the rating

of the pressure washer.

SpECIFICATIONS

Model ALH3228

PSI Max* 3200 PSI

GPM Max* 2.8 gpm

High Pressure Hose 50 ft. (15.24 m)

Presure of Inlet Water 20–100 PSI

Inlet Water cold tap (100 °F max)

Soap Consumption Rate 10% max

*RatedPressureandRatedWaterFlowiswithinmanufacturingtoleranceof

(+/- 10%).

In a continued commitment to improve quality, the manufacturer reserves the right

to make component changes, design changes, or specification changes when

necessary and without notice.

19 - ENG

SERvICE INFORMATION

Do not return this product to your retailer. Please contact our customer service

department at www.simpsoncleaning.com

LIMITED WARRANTY

The manufacturer of this product agrees to repair or replace designated parts that

prove defective within the warranty period listed below at the manufacturer’s sole

discretion. Specific limitations/extensions and exclusions apply.

This warranty covers defects in material and workmanship and not parts failure

due to normal wear, depreciation, abuse, accidental damage, negligence, improper

use, maintenance, water quality or storage. To make a claim under the terms of

the warranty, all parts said to be defective must be retained and available for return

upon request to a designated Warranty Service Center for warranty inspection. The

judgments and decisions of the manufacturer concerning the validity of warranty

claims are final.

These warranties pass through to the end user and are non-transferable. As a

factory authorized and trained Warranty Service Center, the factory will honor the

terms of all component warranties and satisfy claims of the appropriate warranty

provisions.

Normal wear items include, but are not limited to, valves and seals, which are not

covered by this warranty.

This warranty replaces all other warranties, express or implied, including without

limitation any warranties of merchantability or fitness for a particular purpose and

all such warranties are hereby disclaimed and excluded by the manufacturer. The

manufacturer’s warranty obligation is limited to repair and replacement of defective

products as provided herein and the manufacturer shall not be liable for any

further loss, damages, or expenses – including damages from shipping, accident,

abuse, acts of God, misuse, or neglect. Neither is damage from repairs using parts

not purchased from the manufacturer or alterations performed by non-factory

authorized personnel. Failure to install and operate equipment according to the

guidelines put forth in the instruction manual shall void warranty.

This warranty does not cover the following: machines used for rental purposes,

damage resulting from shipping (claims must be filed with freighter), accident,

abuse, act of God, misuse, or neglect. Neither is damage from repairs or alterations

performed by non-factory authorized personnel or failure to install and operate

equipment according to the guidelines put forth in the instruction manual.

The manufacturer will not be liable to any persons for consequential damage, for

personal injury, or for commercial loss.

WARRANTY DOES NOT AppLY TO FAILURES DUE TO:

• Freightdamage

• Damage due to chemical deterioration, scale build up, rust, corrosion or

thermal expansion

• Freezedamage

• Damage caused by parts or accessories not obtained from an authorized

dealer or not approved by the manufacturer.

• Normalwearofmovingpartsorcomponentsaffectedbymovingparts.

20- ENG

ENGINE

Covered by engine manufacturer warranty. See engine manual.

HIGH pRESSURE pUMp (DEFECTS IN MATERIAL AND WORkMANSHIp)

Two (2) years from date of purchase.

FRAME (DEFECTS IN MATERIAL AND WORkMANSHIp)

Ten (10) year from date of purchase.

OTHER COMpONENTS (DEFECTS IN MATERIAL AND WORkMANSHIp)

Includes nozzles, hoses, spray guns, wands, tires, feet

Ninety (90) days from date of purchase.

TROUBLE SHOOTING GUIDE

OPERATIONAL

ISSUE POSSIBLE CAUSE SOLUTION

Engine will

not start

(see Engine

Owner's

Manual for

further engine

troubleshooting)

No fuel Add fresh fuel

Pressure builds up after

two pulls on the recoil

starter or after initial use

Squeeze gun trigger to relieve

pres sure

Choke lever in the "No

Choke" position Move choke to the "Choke"

po si tion

Spark plug wire not attached Attach spark plug wire

Engine switch in OFF

po si tion. Place engine switch

in ON position.

Choke lever in the "Choke"

position on a "hot" engine

or an engine that has been

exposed to thermal heat

for a long period of time.

Move choke to the "No

Choke"po si tion.

No or low

pressure

(initial use)

Spray wand not in

high pressure See How to Use Spray

Wand instructions in the

Operation Section

Low water supply Water supply must be at

least 5 gpm @ 20 PSI

Leak at high pressure

hose fitting Repair leak. Apply sealant

tape if necessary

Nozzle obstructed See Nozzle Cleaning

instructions in the

Maintenance section

Water filter screen clogged Remove and clean filter.

See Cleaning Water Inlet

Filter paragraph in the

Maintenance section for

the correct procedure

Page is loading ...

Simpson ALH3228 User manual

Brand: Simpson

Model: ALH3228

Category: High-pressure cleaners

Type: User manual

Download PDF

report

Simpson ALH3228 User manual

Simpson ALH3228 User manual

Related papers

Other documents